Ubuntu Installation :: Using Grub On IDE Drive And SATA
Aug 1, 2010
I have tried to install ubuntu onto my computer using the live CD. It installed fine, and it put grub on sda (which linux sees as my SATA drive). Windows is installed on the ide drive which linux see's as the sdb drive. It was a successful install and in theory it should work, except it find the windows install first so it boots into windows without using grub. I think that linux assigns the drives using the sata first and the ide second, but windows does the opposite and the ide drive is first and the sata is second.
Is it possible to install grub onto the ide drive and get it to dual boot linux or is it possible to use the windows bootloader to recognize the linux install and chainload grub? I am thinking that if I use grub on the ide drive it will throw an error like what happened during my wubi install and it is unable to find the kernel because it is looking for it on sda, but from a windows install it is sdb. I have tried to get the computer to boot from the sata drive, but the mobo is a bit old and I do not think it is supported.
View 2 Replies
ADVERTISEMENT
May 28, 2011
ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies
View Related
Jan 15, 2010
So I installed SUSE 11.1 a few weeks back with two SATA drives andit's been working great. I recently received another SATA drive and wanted to add the space to my /home directory. I installed the drive and then booted up my computer. It goes through BIOS and POST just fine but when I get to GRUB my computer just hangs there. It doesn't throw any errors, it just sits until I hard reboot it. If I disconnect the extra SATA drive and then try to boot again everything starts successfully. I've done a little bit of searchingbut couldn't find much on this problem.pretty new to linux so I could definitely be missing something. Let me know if more details are needed.
View 9 Replies
View Related
Feb 28, 2011
I have a HP PC that I have installed a PCI SATA controller in. The PC doesn't support booting from the card.... So here is what I would like to do. (btw..I'm a seasoned noob on Linux.) I would like to be able to boot ubuntu 10.10 from a usb pin drive 2Gb to a point where the kernal can recognize the SATA drive then start the OS from the SATA HDD.
I can see and access the drive if I boot to a live CD but when I install it won't boot because the PC's bios does not see the PCI card. This has to be possible but my Google foo isn't strong enough to find out how. Would a simple GRUB install on the pen drive work?
View 5 Replies
View Related
Feb 15, 2010
Prefactory note - I've also posted this question on the Ubuntu forum, but so far no solutions have been provided.
My system has several hard drives. The important ones are these:
Sata 1 - Fedora 12
Sata 3 - Windows 7
Slave 1 - Storage
Sata 1 was NOT installed with grub. When I switch OSs, I do it by rebooting and choosing the other drive as primary.
I downloaded an ISO of Ubuntu 9.10 (64 bit) and burned the DVD of it. I backed up Slave 1 and then booted off the Ubuntu DVD. I clicked on "Install Ubuntu", selected Slave 1, and installed onto it.
Subsequently I rebooted the machine, going into the BIOS to boot off Sata 1, so I could get my Fedora Firefox settings to replicate them under Ubuntu.
Instead of Fedora 12 booting, Grub 1.97 came up. It had 5 choices, Ubuntu, Ubuntu Repair, Memtest, some other Memtest, and Windows 7.
Subsequently I tried cracking the box and physically disconnecting Slave 1. When I rebooted Sata 1, it crashed to a grub command line. Apparently when Ubuntu installed, it infected Sata 1 with grub, even though it installed the rest of Ubuntu on Slave 1.
I really, really, REALLY need to get access to the Fedora 12 drive. It's got my work on it.
how I can get grub out of Sata 1 and regain access, or maybe reconfigure it so it recognizes the existence of Sata 1? Personally, I don't want it there; that's why I never installed it in the first place.
View 14 Replies
View Related
Oct 5, 2010
Install of 10.4 64 bit not showing choice of sata drives on install. W 7 on sata a drive, SUSE 11 on sata b drive. Need to load Ubuntu 10.4 on drive b, but not given choice of drives on the install. Only "clear drive" listed on the install window.
This is not the case on 32 bit, a graph with drives listed. W7 a runs Adobe CS5, the Ubuntu 10.4 has excellent font, type display on the live cd.
View 1 Replies
View Related
Oct 7, 2010
I've been trying to find a solution, I've looked everywhere but no luck. I have a 1TB drive, checked the cable & it's connected to motherboard SATA0. That motherboard is dual booting fine (windows7 + Ubuntu 10.04).
My problem is when I connect the other SATA drive, SATA1. Upon restarting my machine, nothing happens & I dont see any boot menu (grub).
I've checked the bios settings, boot drives are in order:
CD-ROM
SATA0
SATA1
To check if the second drive has physical errors, I've connected it as SATA0 (alone) & installed successfully windows & ubuntu 10.04. I formatted it & installed ubuntu studio. The drive is working fine. So I formatted it again, & now it's not connected.
How can I make it work? I want SATA0 to have both windws/ubuntu, & the SATA1 to be just a data storage drive.
View 6 Replies
View Related
Feb 17, 2010
i have a strange problem while trying to install Ubuntu 9.10 64bit (also tried with x86 - no luck).My system specs : Motherboard : ASUS P5B VM SE (PATA : JMB368 / Intel ICHHD : Seagate SATA II 3GBit 320 MB (connected in SATA port 1)CPU : Intel Core 2 Quad 2500 GHzI must state i installed Windows 7 without a problem. After that, i tried to install Ubuntu 9.10, first 64bit then x86 but in every case the setup starts, i select language / location etc and when the partitioner starts i see no hard disk drive. Same happens if i try the alternate install cd.
I must mention here that if i click on "Exit" and access Ubuntu Live CD desktopm i can go System >Administrator > Disk Utillity and GParted. In both utillities my HD shows up just fine. So what could be the problem ??? I tried starting ubuntu with pci=nommconf irqpoll -> no luckHere is the lspci output :
ubuntu@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82G965 Integrated Graphics Controller (rev 02)
[code]....
View 9 Replies
View Related
Apr 5, 2010
I have a Desktop system using the Intel DG45ID motherboard with integrated graphics. I can't install from the 9.10 LiveCD. It can't find the Hard drive which is on the chipset's SATA controller.However, I can install 9.04 just fine. I can even do the 9.10 upgrade without a problem.Does anyone know if this bug has been reported. I'm hoping 10.4 has this fixed. I'll test the beta to see
View 9 Replies
View Related
Aug 19, 2010
I am about to do a clean install of 10.04 (64-bit) on a ThinkPad X201. The machine will only be running Ubuntu (i.e., no dual-boot). Is there any reason to use compatibility mode for the SATA boot drive, or will AHCI work fine?
View 2 Replies
View Related
Sep 15, 2010
I have appealed to anyone on this forum site for any help on installing Unbuntu 10.04.1 LTS on a MACBOOK PRO (Mid 2007 Model. Basically I've followed a few threads & posts on how to Quad boot a Macbook Pro & it seems pretty straight forward,however. Ubuntu is not playing ball for some reason?? The first attempt I tried I had the partitions as follows:
I am using a 500gb sata internal hard drive.
WIN 7 - 125gb
STORAGE - 15gb
WIN XP -125gb
MAC OSX - 180gb
FREE SPACE 50gb - Formatted DOS - Which would become the EXT4 & SWAP FILE partition.
After following instructions:
http://hydtechblog.com/2009/01/26/du...windows-vista/
[Code]...
View 7 Replies
View Related
Mar 12, 2011
I want to install Ubuntu 10.10 via a DVD-ROM but I faild. I got the message "no common cd-rom drive was detected." I have tried to install ubuntu 11.4 and failed too.
Hardware Setting:
DVD-ROM was attached to SATA 3.0 port.
SATA controller was set to IDE mode.
PCH is CougarPoint.
I use the same hardware setting to install Red Hat 6.0 and it works fine. I tried following boot option but in vain: noapic, acpi=off, nodmraid, all_generic_ide. It is ok to boot via a live usb but ubuntu 10.10 still can't find DVD-ROM. I have to use the hardware setting I descripted to install Ubuntu 10.10.
dmesg:
Code:
[ 1.892198] ata1: SATA max UDMA/133 cmd 0x3098 ctl 0x30ac bmdma 0x3070 irq 19
[ 3.309652] ata1.01: failed to resume link (SControl 0)
[ 3.469636] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[code]...
View 5 Replies
View Related
Apr 18, 2009
I have just changed my OS from Vista to Linux Fedora 10. After looking at my system I notice my SATA drive was not recognised its my 2nd drive. Is this a normal think or can it be fixed.
View 1 Replies
View Related
Mar 21, 2010
Somehow Fedora 12 does not find one of my Sata drives (Seagate Barracuda 500GB) on the motherboard (Asus P5Q pro). The drive is attached to SATA_E1, which is a Silicon Image Serial ATA RAID connector. The drive currently has Windows Vista 64-bit OS which has been working fine. Fedora install loads correctly without errors, but only shows my RAID system on SATA ports 1-6.
WHAT I HAVE TRIED:
I have tried showing RAID as IDE in the BIOS, and setting it to compatible mode. Still does not detect.
I have tried setting the drives to ACPI mode in BIOS. No effect.
OTHER INFO:
I'm installing the x86_64 version of Fedora 12. I have run the Debian i686 installer and it picks up this volume without issue.
View 6 Replies
View Related
Feb 21, 2010
I have been trying to install Ubuntu on my main computer for some time. I think I have two problems: my hard drive and video card. I started with Ubuntu 9.04 but got nowhere. I am now trying Ubuntu 9.10 32 bit. I can at least use the live cd if I put the video on safe mode. Just in case you are wondering, I have tried other distros: Fedora, OpenSUSE, Slitaz, Wolvix, etc. Only Slitaz and Ubuntu 9.10 works on a live cd.
Information on my computer:
OS: Trying to install Ubuntu 9.10 32bit
Motherboard: ASUS M3A78
CPU: AMD Phenom 9500 Quad Core
Video Card: Galaxy Geforce 9500 GT 1GB 128 bit DDR2 (Nvidia) Hard Drive: Hitachi 1 TB Sata Drive 3 Gb/sec 7200 RPM Ram: 4 GB (I think, its been awhile since I built this thing) DVD Burner: LG I think I have two problems: the Sata Hard Drive and the Video Card. When I go to install it, I can get to the install menu but from there all I get is a blank screen. I have tried to put the video in safe mode then install it but I get the same result: a blank screen.
How do I know if Ubuntu recognize the Hard Drive and Video Card? I tried the mount command to see what it sees but I didn't notice any Sata Drives. I was told that I may have to do something with the kernel so it will recognize my Hard Drive. How would I do that?
I have been working on this for awhile now. On a side note, does it matter which Sata Plug the hard drive is on? Right now I have it on the 1st one but I would like to move it to the second one because I want a dual boot system. And yes I know I can use the same hard drive but I would like to keep them separated and use a switch to pick which OS system to use.
While running on the Live Cd, Ubuntu seems to know about my video card and ask to install some drivers but then it asked to be rebooted and it came back up not recognizing anything; video card and hard drive that is. On the live cd I ran the following commands: lswh, lspci, mount, and df. I am not too sure if they will show if the hard drive and the video card are working since I did them on the Live CD. Also on the lspci command, I did this after Ubuntu loaded the driver for the card.
[Code]...
View 9 Replies
View Related
Apr 16, 2010
I decided to install the Ubuntu Netbook remix (9.10, I believe) on this extra IDE hard drive I had (my other three hard drives are SATA.) My primary hard drive contains a Windows XP, my second contains Windows 7, and my third SATA drive is just NTFS-formatted storage. I went through the installer and choose to format and install on my 40GB IDE hard drive, which it did. Then it finished and rebooted. It apparently decided to install the GRUB bootloader onto the primary hard drive (not the one it was installed on,) which was not my intention. The bootloader froze the boot of my computer and wouldn't work. (Stuck at loading GRUB.) I couldn't even get to the BIOS. So I pulled the plug on the primary hard drive and tried to boot again. I could get into Windows 7 just fine, but that was it. The problem, though, is that the CD drive (also SATA) no longer shows up in My Computer. Also, after changing the boot order and replugging in the former primary hard drive, it wouldn't show up, either. Nor would the IDE one (though I'm pretty sure that's because Windows doesn't understand the EXT (or whatever Ubuntu uses) file system.
Does anyone know why this occurred and how to get those drives to show up in Windows again? I don't really care to get the netbook remix working here, since this isn't even a laptop, it was just an experiment. Also, I'd love to know how to remove GRUB from my primary hard disk so that I can boot from it again.
View 3 Replies
View Related
Dec 27, 2010
i have a netbook compaq mini with a sata toshiba hard drive.XP was installed on this machine until the hard drive started to have bad blocks.Then i bought a mypassport500go to install f14 on it.It worked but know the sata hard drive is more and more faulty.When i try to boot f14 it displays :acpi : package has zero elements. So i cannot boot.I tryed rescuecd, does not work either.i tryed many kernel params to disable sata at boot but it seems to be builtin.there is no option in the bios to disable the hard drive.
View 8 Replies
View Related
Mar 2, 2010
I can dual-boot on my PC by using my SATA drive for Windows & a second IDE (PATA) one for Ubuntu.However when I try to install both OS's on the Primary SATA drive side by side only one is detected (and I have no option to boot the other).
I have a friend with the same problem who is trying to boot Win7 and Ubuntu off the same SATA drive and the same issue occurs on his (He doesn't have the second drive as an option as I do).
Does anyone know a way to get side by side installation to work on one (SATA) drive? Failing this is it possible to boot Ubuntu off and External hard drive and still be able to dual boot Windows & Ubuntu?
View 9 Replies
View Related
Aug 13, 2010
Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies
View Related
Mar 9, 2010
I installed Red Hat Enterprise Linux AS 4 Standard Edition on a HP dc5800 PC with a SATA drive. To install the system I use the boot option: Linux pci=nommconf After the installation is done The system is hangs while uncompressing the kernel. the boot loader is GNU GRUB:
root (hd0,0)
kernel /vmlinuz-2.6.9-55.ELsmp ro root=LABEL=/ rhgb quiet
initrd /initrd-2.6.9-55.ELsmp.img
It hangs on: uncompressing Linux... OK, booting the kernel
View 7 Replies
View Related
Dec 28, 2009
would it be possible to clone an IDE hard disk (on which I installed Fedora 10) on a SATA hard disk, and that programs can succeed
View 10 Replies
View Related
May 1, 2011
I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
View 4 Replies
View Related
Feb 28, 2010
I have read others getting Grub error 2, but i cant fix the problem. I have 2 sata HDDs. I suspect the problem is something to do with RAID?
View 2 Replies
View Related
May 23, 2011
I'm trying to install Natty from a USB thumb drive on a SATA SSD. My main system is OS X. The method to create an instal USB disk on the download page didn't yield a bootable disk (the partition was readble, with the right files, but GRUB never started). The quick method from the clemsonlinux wiki gave me a minimal bootable drive, though.From there, I tried to install Natty on my SSD.
Once again, the partitioning process appears to work fine, the files are copied, no problem, but the GRUB install fails silently.I think that the problem comes from the fact that, when I boot from the USB drive (even if the SSD is set as the first boot device), the SSD ends up at /dev/sdb, whereas it would be at /dev/sda if the machine could be booted from the SSD.I chose the automatic partitioning method and ends up with sda1 (/), sda2 (ext) and sda5 (swap).If I launch the installer in recovery mode and ask to mount /dev/sdb1 as root, mount reports that sda1 is / (sda1 doesn't even exist), but blkid reports the SSD as /dev/sdb.
The output of the boot_inf_script is clearly pathological, but I didn't manage to get it out of the machine with what I have (gmail is broken in lynx).I've also tried to install LILO instead of GRUB. LILO boots, but doesn't find /dev/sdb (which is now /dev/sda) and gives me a busybox prompt.I've tried to install GRUB from there, but, once again, I get a black screen at boot time.
View 1 Replies
View Related
Jun 11, 2010
i'm well versed with the fstab but i'm just curious if there is ubuntu way
View 3 Replies
View Related
Jan 12, 2011
I'm having a bit of a problem enabling any sort of permissions for my 1TB SATA HDD on /dev/sda1. Using Nautilus and wine, I'm trying to play games already pre-installed on my Windows 7 partition. When ever I right-click>permissions>Enable execution, it reverses the changes. I don't know if this is relevant, but id rather not copy anything on to my /dev/sdb2/ partition because its about 1/10th the size of sda1 (142GB free to be exact). Is their any way to make a permanent change? I don't really mind if it's a solution in the terminal... So long as it doesn't mess up my ability to boot Windows 7.
View 3 Replies
View Related
Feb 5, 2010
I am helping my pal to get into Debian (yes first timer).He is running W7 on a 500G SATA HDD and he has another 250G SATA HDD that he wants Debian to go to.Will Debian install grub on the master bootloader even if the installation is going on a separate hard drive?I have dual boot before but on the same hard drive.
View 6 Replies
View Related
Jan 16, 2010
I have 4 hard drives in my computer. 1 for may root and home partitions. 2 extras for storage and 1 for Windows. I have the hard drive with my root and home partitions set as the first hard drive in the bios. However, in the Ubuntu setup it isn't the first one in the list. I would have thought that the first drive would be get set to sda. That is not the case.
View 1 Replies
View Related
Apr 29, 2010
I'm trying to mount my SATA drive that has Windows on it under Xubuntu, it's NTFS formatted, I tried adding it to fstab, I know the /dev points are right I checked with sudo lshw -C disk and with fdisk -l, the drive is partitioned 3 ways 1 for Win7, one for Win7's system info partition or whatever, and 1 for documents, but when I try mounting with mount -a with /dev/sda1 (which is where the windows partition should be) I get this:
[Code]...
View 3 Replies
View Related
Feb 23, 2011
Having an issue I've been unable to resolve for for a week now. I've 2 drives, SATA1 for OS and operating files, SATA2 for media storage. came home last week to an update manager window present and error in Transmission stating unable to second drive due to "Read Only" status. the drive was never set to read only status but following the update manager a reboot was needed. once rebooted, the GRUB menu came up (dual boot system), selected Ubuntu then booting stopped. blank black screen with blinking cursor. rebooted several times, checked bios recognition of both drives, replaced cables, switched power to drive to separate cables, used different SATA ports but nothing worked. finally removed the second media storage drive and Ubuntu booted normally. now any time i connect the second drive and reboot it fails to boot into ubuntu or XP. i removed the media drive and installed it in another computer and it worked normally. have searched everything i can but no answers have been found so far. wondering if anyone here has had similar trouble or has idea for what to try.
I'm using Ubuntu 10.04 64 bit with current 3.6.32-28 kernel
View 4 Replies
View Related
