I have (3) 60GB SSD. I want to use (2) in RAID 0 for Ubuntu and (1) alone for Windows 7.
What is the best way to get about this? I know how to create the RAID 0 array with the (2) disks and install Ubuntu on it. But how do I get the RAID array with Linux on it to dual boot with Windows 7?
Linux - RAID 0 (2) SSDs
Windows 7 - (1) SSD
I have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
I set up an array of 2 hhd in raid0 using intel ICH7R, and i have a win7 installed on it. I'd like to have a dual boot with karmic, too. I googled a little bit and i found that it's not so easy as i thought. Are there anyone who's experiencing my same situation?
View 1 Replies View RelatedIs it humanly possible to have a dual boot system and have it in RAID 0
I have three Hard drives.....
The three drives that I have are250GB IDE
1TB Sata
1TB Sata
And I edit . produce a lot of music/videos
What I am looking to do it have my 250Gb IDE drive as my Operating system (partitioned in two or something, one for Windows Another for Ubuntu)
And I would like when I am on either Operating System (ubuntu/windows_7)
its see's ,my computer as having a 2TB HDD (setting the two 1TB HDD's in RAID 0 )
So in Laymans... 250GB for OS's and 2TB (2 x 1TB HDD) as DATA drives
Currently I have windows 7 x64 installed on a pair of raided ssd's using an x58 motherboard(ich10r) and I want to duel boot ubuntu x64 (either 9.10 or 10.04) on another harddrive (not part of the raided ssd's). Does anyone know if this can be done? I haven't found anything out there about this. I have tried to install Ubuntu from the CD. It gets to the install screen booting from the CD, but it doesn't let me install or try Ubuntu. I hit enter and nothing happens. I can look through all of the options but can't install or boot into Ubuntu.
View 1 Replies View RelatedI was trying to dual boot ubuntu on my desktop which has windows 7 already installed on it with raid 0. I have 2 500GB hard drive and when I boot from cd and try to install ubuntu it only detect one of my hard drives and it said I only have 500GB and there is no OS installed on this machine! I look online but I couldn't find any solution!
View 9 Replies View RelatedI originally wanted to dual install 10.10 64 Ubuntu with Windows 7 64 RAID 1 HP PC, but RAID got corrupted and I could find no fix online except using fakeraid unsupported software. The whole thing blew my muind. I gave up after 4 or so reinstalls of windows 7 to fix RAID. So I decided to install a dual boot 10.10 Ubuntu i86 with my old WinXP i86. I kept getting these errors at boot up: unknown filesystem, file not found, out of disk, no such partion and so on. I tried just about every grub reinstall I could find, including article here: "Recovering Ubuntu after Installing Windows."
After a number of tries my friend installed Ubuntu successfully, but then when I installed windows xp I am stuck here, again. I did do the Reload grub tutorials again as well. I may just give up on WinXP and have my friend reinstall Ubuntu for me.
[Code]...
I am currently with Wubi 10.04 under Vista and my Dell XPS 630i has a 1 TB Nvidia RAID controller.First image (Option A) suggests /dev/sda as device for boot loader installation, while second image (Option B) suggests /dev/mapper/nvidia_bcidhdja.I think that the way of keeping the RAID would be using Option B as the device for boot loader installation. Would Option A break the RAID instead?
View 1 Replies View RelatedI'm having serious troubles to install ubuntu-10.04.1. My raid is an hardware raid with intel chipset. Note that win7 is already installed and working with my raid. I made some space from windows, to install Ubuntu (40gb). First, I run the installer, everything seems to be fine. I choose to install Ubuntu were there is the most space free (sorry, I'm not sure about the real terms used there).
Then my partition with the vista loader appears. So the installer can see my raid, and should work fine (everything is detected correctly). But once I'm in the end of the installation (around 95%), a pop-up appears, and tells me that Grub can't install in /dev/sda and it's a fatal error. I can choose an another destination, but it doesn't seems to work.
I am attempting to install Maverick on an older pc. It has (2) mirrored 153 GB SATA drives. I set aside 33GB for a linux partition, by shrinking the partition in Vista.
Choosing to "Install along side windows" is not an available option. I can only choose use who disk, or use empty area. I choose use the empty area, and the Ubiquity installer gets hung up when attempting to format the empty space as EXT4. When I scroll up on the output I notice some error messages referencing NTFS. When I use Gparted it shows a possible problem.
Quote:
Warning:
The device /dev/sda1 doesn't exist
ntfsresize v2.0.0 (libntfs 10:0:0
ERROR(2):Failed to check 'dev/sda1' mount state: No such
file or directory
Probably /etc/mtab is missing. It's too risky to continue. You
might try an another Linux ditro.
Unable to read the contents of this file system!Because of this some operations may be unavailable.
The following list of software packages is required for ntfs file system support: ntfsprogs.
I ran chkdsk /r on the Vista partiton, in case there was a problem there. The issue still persists.
(This is for a 100% Clean install)
Q1) I was wondering if it is possible to Dual boot Ubuntu with Windows XP on a 1TB RAID-0 setup ?
Q2) Also, is it possible to create a SWAP partition (for Ubuntu) on a NON RAID-0 HDD ?
Q3) Lastly... I read GRUB2 is the default boot manager... should I use that, or GRUB / Lio ?
I have a total of 3 HDDs on this system:
-- 2x 500GB WDD HDDs (non-advanced format) ... RAID-0 setup
-- 1x 320GB WDD HDD (non RAID setup)
(The non RAID HDD is intended to be a SWAP drive for both XP and Ubuntu = 2 partitions)
I plan on making multiple partitions... and reserve partition space for Ubuntu (of course).
I have the latest version of the LiveCD created already.
Q4) Do I need the Alternate CD for this setup?
I plan on installing XP before Ubuntu.
This is my 1st time dual booting XP with Ubuntu.
I'm using these as my resources:
- [url]
- [url]
Q5) Anything else I should be aware of (possible issues during install)?
Q6) Lastly... is there anything like the AHCI (advanced host controller interface) like in Windows for Ubuntu?
(Since I need a special floppy during Windows Install...) I want to be able to use the Advanced Queuing capabilities of my SATA drives in Ubuntu.
I've recently had trouble reinstalling my Ubuntu system as I was getting various unusual errors as described in my old thread here. I thought it was probably something to do with my RAID-0 array which was pre-installed on my laptop from purchase being corrupted or something like that (if it's possible). I decided to simplify things for myself (not understanding RAID arrays much) so I just removed the RAID array and installed Windows and Ubuntu on the now separate hard disks. It worked fine.
I noticed quite a significant performance drop, however, with even Ubuntu boots taking longer than 30 seconds despite my laptop being both high-spec and only a few months old. Windows, as you can imagine, was dreadfully slow. I wasn't entirely convinced that this was entirely due to the loss of the RAID array - as even low-spec laptops with presumably no RAID arrays are supposed to boot Ubuntu in under 30 seconds apparently - but I read that RAID-0 arra
I did some linux installation in the past but never get along with it. now I decided to give it another shot because I need it for the information security class I'm taking.
I have a gigabyte ga-p35-ds3 with 2 WD 320GB HD on a raid 0 array (motherboard raid). I have windows 7 x64 already installed on the raid and would like to install ubuntu 9.10 x64 dual boot with it.
The problem is that the installation does not recognize the win7 on the disk, it does recognize the raid as 1 640GB disk but with nothing on it so I can't processed with the installation without loosing the win7 installation with everything on it.
another weird thing is that after I quit the ubuntu installation and restart the computer the raid 0 fail to load. after I shutdown the computer and start it again the raid is up again and the win7 loading ok.
I have to install it in a dual boot with win 7 without reinstalling everything from scratch.
I'm having a problem installing RHEL-5 on my system. I have Windows 7 installed so far on a Dell XPS workstation that came with hardware RAID 0. I have 2 x 500 gb hard drives. So I went in Win 7 and partitioned my disk to leave about 75 gb of unallocated space to install RHEL-5 on. I load the RHEL-5 DVD into my disk, restart my comp, and just follow installation steps. Use about 73 GB as an ext3 partition for the RHEL-5 and have about 2 GB reserved for swap space. RHEL-5 installs, and I'm all done. However, when I reboot the computer, the GRUB boot loader fails to load. I'm directly taken into Windows. How do I recover GRUB so I have the option of loading into RHEL-5?
View 9 Replies View RelatedI just installed SUSE 11.2 as dual-boot with WinXP on an older system that has a 160GB PATA drive and a 500GB SATA RAID drive. I left about 80GB on the PATA drive unpartitioned to accommodate SUSE. During the initial installation attempt, SUSE was determined to install on the RAID drive instead of the PATA drive, so I disabled the SATA drivers in the BIOS to force the installation on the PATA drive. This was successful, but now there is no access to the RAID drive from SUSE because there is no driver and it is not mounted. I reactivated the SATA drivers in the BIOS and the RAID drive reappeared in WinXP with everything intact. The SATA drives now appear in SUSE under Hardware Information as "/dev/sdb" and "/dev/sdc" and the listed driver is "sata_sil".
So how do I get the RAID drivers installed in SUSE and then mount the drive so it can be browsed/modified from Dolphin? I would also like to be able to browse/change this drive from other computers on my home network through samba, just like with WinXP.
Ive created two RAID0 partitions on my drives, a 500GB and a 60GB. Im trying to install Ubuntu on the smaller partition (ive already put Win 7 on the larger one) and every time when i get right to the last part of installation it says Grub couldnt be installed. "the grub package failed to install in arget......."
View 1 Replies View RelatedI have a pre-existing setup with Windows XP Professional and CentOS5.5 on a dual boot setup with the Linux drive setup as the primary drive hosting the grub menu.
I am replacing these machines with new updated ones and they have windows setup on a RAID0. I think it would be easiest to follow my previous setup and move the RAID to secondary SATA ports and put the linux drive on the primary SATA port, or should I just change the boot order in the BIOS to have the secondary linux drive boot first?
can I move a RAID setup to secondary controller ports without breaking the RAID?
hey guys i am trying "again" to dual boot on my gaming computer, and i am failing miserably. i boot the cd, it detects the hard drive i set the partitions and press finish and either on the partitioning or the files copying the installer crashes. what can i do to make it work with raid 0 (nvidia chipset).
View 5 Replies View RelatedI am quite experienced user of Ubuntu desktop / server distributions. Recently my desktop 9.10 disk failed and I decided to reinstall using 10.04. My configuration is a dual disk dual bot system. I have XP Pro SP3 on one disk and Ubuntu 10.04 on second. XP has own, untached MBR ubuntu got Grub 2 installed on the same disk as Ubuntu. Ubuntu disk is booting first in BIOS. Grub 2 detected both system, however I can boot only to Ubuntu. When I am trying to boot XP I got black screen only. Looks like booting is stack in BIOS stage, because crt+alt+del reset system.
I read Ubuntu forum, search Google and did not come with any solutions. My XP MBR is OK. I can boot directly, choosing XP HDD in BIOS as a starting disk. All entries in grub.cfg looks fine to me. I made 3 different clear installations of Ubuntu. Each with the same result. I reinstaled Grub2 with no effect. I wonder if this may be a hardware/Grub 2 compatibility issue. I am using quite old components.My motherboard is Assus P4C800 Delux. I have 5 HDDs 2 CD. Exactly the same configuration was OK with 9.10/XP dual disk dual boot using Grub legacy.
[Code]...
I have a (slightly complicated) dual/multi boot system.
I keep getting boot errors (when choosing ubuntu from the grub2 menu)
Code:
Serious errors were found while checking the disk drive for /boot
If I switch off and restart, ubuntu will then start without issue.
My setup is like this ....3 disks, one with 10.10 clean install - so Grub2, separate partitions for /, /boot and /home, one with windows 7, one with windows XP and 10.04 wubi (this is my old disk which I will trash once I'm happy with my upgrade to 10.10 & 7 on separate disks.
I installed 7 and 10.10 with ONLY their disks installed. After both were working, I added all disks and rejigged the grub2 menu (using update-grub and StartUp-Manager).
This problem only seems to occur if my previous boot was not 10.10 ( I will investigate this further). It's as if something (grub2 ?, the bios ?) is remembering part of the previous boot and not using the grub2 menu completely.
I had a dual boot machine with fedora 12 and windows vista and I could use grub boot-loader to switch between two. Few days ago windows got corrupt and I have to reinstall it. I put windows 7 now and as usual it erased grub. So to reinstall I put the fedora 12 installation CD on and followed some usual setup steps. When I got the command line I issued the command "grub-install /dev/sda" (sda not hda because It showed bunch of sda, sda1..) but surprisingly it said grub command not found. I remember doing it before while it worked fine.
View 4 Replies View RelatedI'm a long time windows user and it-tech but I have long felt that my geek-levels were too low so I installed Ubuntu last week (9.10 x64). Hopefully I can make it my primary OS. I have two 80GB drives in RAID-1 from my nforce raid controller, nforce 570 chipset. Then a 320 GB drive where I placed ubuntu and it's also where grub placed itself. And also a 1TB drive.
When grub tries to boot XP I get the error message: "error: invalid signature" I checked the forum as much as I could and tried a few things, but no change.
Drives sdc and sdd are the two drives in raid, they are matched exactly, but detected as different here. I really think they should be seen as one drive.
how I can make grub work as it should?
Also, if/when I need to make changes to grub, do I really have to use the live CD?
Code:
============================= Boot Info Summary: ==============================
=> Grub 1.97 is installed in the MBR of /dev/sda and looks on the same drive
in partition #1 for /boot/grub.
=> Windows is installed in the MBR of /dev/sdb
=> Windows is installed in the MBR of /dev/sdc
[Code].....
I am using the 10.04.1 x64 Kubuntu live CD to install Kubuntu on my FakeRAID 0 array, I tell it not to install grub as i know it is still currently broken. the install goes flawlessly. However on first boot using my live grub CD unless i tell my computer to point to the CD it will hang (which it is told to boot from CD first so i'm not sure why it does.) When i tell it to boot to Linux, it will not boot saying the kernel is missing files (to much to sadly list, all i do not understand) then offers me a terminal to input "help" into for a list of Linux commands. Windows 7 pro x64 works just fine CD was downloaded VIA P2P if it matters
View 6 Replies View RelatedI have a Asus P5Q-E with SATA Raid (fake Raid ?) with 2 250Gb disks on Raid 0 and have Windows 7 installed. Freed some space and want to install Ubuntu 11.04 alongside Win7. Install choosing the "alongside" option. Installed...reboot...grub rescue (error no such device). Win7 disk recovery and got access to Win7 again. Where is Ubuntu ? Nowhere... the free space continues free (not partitioned) and found no evidence of ubuntu install. Ok...second try with "something else" option, created /boot /swap and / partitions and installed grub on /boot partition (this time I want to use windows boot to choose...and if it fails the instalation again, at least I got Windows). Installed...reboot...grub rescue.
Again, the free space wasn't partitioned and the installer spend some time doing something but there is no evidence of ubuntu install. Also grub seems to be installed on first disk (even when I choose /boot as device bootloader installation) - I've used EasyBCD to create an entry on win bootloader and when I choose that got grub> (not grub rescue>).
Can Ubuntu be installed on such conditions ?
Have just installed 9.10, again, many failed attempts previously.Cannot get to boot up and show menu on dual boot with Vista initially,However when I delete the grubenv file the system boots ok and works fine.But does not show the grub menu to choose boot up choices.Got the information to delete the file on some posts elsewhere about booting problem, and tried a longshot and got into Ubuntu for the first time from trying to install now for 3 months!The problem is the file grubenv is created each time so on subsequent boot ups the sytem fails to boot again.The Grub version is 1.97 beta 4, most up to date for Karmic I think, I have seen a version 1.98 but dont think its for Karmic?
Is there a way to modify the grub.cfg file to stop this problem ( all posts say dont touch this file??Or install a script to delete the grubenv file on shutdown as a workaround for me, (I have no idea how to do this whatsoever, I'm not familiar with linux at all)I did read that this problem was fixed/patched in Grub version 2, but dosn't seem.so on my system afetr I updated it when I got into Ubuntu.I couldnt find the patch or fix, I got the information I am on about from this post:URL...It seems to say it was fixed or patched by Colin Watson reading through, but I don't really understand whats being said or how to get the patch on my system if indeed there is one?Sorry for being a bit thick about all this, its a bit beyond my brain now, hope somebody can help out as I have enjoyed my brief bit of fun in Ubuntu.
I have a netbook running Windows XP as standard. There is also a recovery partition which came from the factory.
In the past I installed Ubuntu (I think 9.something) from USB key and all worked fine. However my XP became corrupted and I needed to do a repair on it. After this, Ubuntu became removed from the boot select menu.
Since then, Ubuntu has become updated to 10.04, which I now cannot install.
The Live CD tells me there is a "file IO error" and simply stops installation at around 70%.
I did manage to get into Ubuntu from a Live USB using Wubi. However when I chose to install Ubuntu to a Harddrive, the option to "install side by side" was missing.
After reading on the forums, I did a chkdsk /f on Windows and tried again. Now my liveUSB does not show a boot menu!
When I select to boot from USB stick, the screen goes blank with a flashing cursor. Ctrl+alt+dlt reboots.
I'm really lost here! It seems when I fix one problem, another problem arises!
Also when trying to instal Ubuntu within Windows, the process goes through to 100% and asks me to reboot. When I do so, the option for Ubuntu does show in the boot menu. However when I select it, I get an error "Windows boot failed: file wubildr.mbr and status: 0xc00000f - something is corrupt".
I have Ubuntu 10.04 LTS and Windows XP installed on my laptop. Usually when booting, I get the GRUB 2 menu and I can boot into either Ubuntu or XP.I was playing around with EasyBCD, then after trying to remove it I was unable to boot into Windows, I used a Windows 2000 CD recovery console to fix the MBR (using: fixboot and fixmbr).Now Windows starts up when I power on, but I don't get the grub menu anymore with an Ubuntu option. If I boot from the Ubuntu Live CD and try to mount my Ubuntu partition (/dev/sda5) I get this error:
mount: wrong fs type, bad option, bad superblock on /dev/sda5,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
[code]....
I recently got a netbook and setup as dual boot between win7 starter and 9.10 (64bit). Win 7 starter is not impressive so i want to nuke it and give the space all to my /USR partion. I am comfortable working with Gparted and assume that i can launch using my gparted live usb and delete the windows partion and then resize the /usr partion.
what changes do i need to make w/ Grub2? I would prefer not to see the Grub menu at all and have it load right the main kernel if possible. Also, if this is possible is there a way to get to the Grub menu during boot should i need to select a different kernel?
I have just installed Ubuntu 10.4 x64 onto a machine with Vista Ultimate x64. When I boot the machine, the Windows option comes up in the GRUB menu. However, when I attempt to boot Windows, I receive the following error: No such device: de80ab9f80ab7d21. error: No such partition. Press any key to continue...
I looked around and found a similar issue at [URL] However, before trying to fix the issue by guesswork or via solutions that worked for a similar, though not necessarily identical problem. I've run the boot info script (see output below) mentioned several places on this site as a valuable input for boot problem tracking. how to get Windows to boot on my computer?
[Code]...