Ubuntu Installation :: 10.10 And Win7 - Device For Bootloader
Nov 20, 2010
I'm trying to create a dual boot with ubuntu 10.10 on my acer laptop with windows 7. I looked at my hard drive and I found out that it has three partitions, one called System Reversed, another one called PQSERVE or something like that (which is a recovery partition since acer laptops dont have a recovery cd), and the third partition is C:.
So I shrunk my C: drive, and created a 44gb partition for ubuntu, and a 6gb swap. I then booted with the ubuntu cd and went into manual partitioning. I selected the 44gb partition as "/", and set the 6gb partition to swap. The problem is at the very bottom of the partition manager, where it says "Device for boot loader installation". I get several choices, and I'm a bit unsure which one to choose.
The choices are as follows:
/dev/sda ATA WDC WD5000BEVT-2 (500,1GB)
/dev/sda1 Windows Vista (loader)
/dev/sda2 Windows 7 (loader)
/dev/sda3
/dev/sda5
/dev/sda6
My first thought was of course why do I have a vista loader? I don't even have vista!
I had vista installed, then I installed Win7 on a dif. partition. Then I installed Ubuntu 11.4 over the vista partition (formatted first), and now I can't get into Win7. I'm really at a loss. I've tried the Win7 disk, and it doesn't detect the Win7 installation. I've also tried sudo update-grub, and it doesn't seem to detect the win7 install either. I've tried making the Win7 partition bootable using gpart as well. I'd like to dual boot Win7 and Ubuntu, however I need to do that.
I installed Windows 7 First then give partition space of 25 GB for my Ubuntu. However, I prefer using Windows 7 BootLoader instead of using Ubuntu BootLoader.
What is the preferred bootloader with Ubuntu 10.04 and windows 7, when multiple booting also with Vista and XP all on one hard drive and each on separate partitions? All are installed except Ubuntu and now boot with the windows boot manager. I have heard that if you install grub 2 on the MBR, then boot windows 7, that it will replace the grub boot code with windows boot code automatically. So is it best to use that NeoSmart EasyBCD tool to add Ubuntu in to the windows boot manager, and can I install grub on the boot sector of Ubuntu's root partition ?
I have a Dell Studio 14 laptop with Windows 7 64bit preinstalled. The processor is core i5 and the machine has 4GB RAM. I freed 25GB of memory from my Hard disk and tried to install Ubuntu 10.04 (AMD). Everything went fine. I restarted and Logged into Ubuntu. It worked like a charm. Then I restarted to Windows7. This also worked well as expected.
But, when I rebooted again, I got a black screen saying that �No modules found. Press any key to restart� When I press a key, it says �No operating system found�, probably after checking through a network (it printed lines starting with PXE).
I tried exactly in the same way with Ubuntu 8.04 in my machine, and this worked without any problem. The Bootloader was not corrupted after restarting from Windows. I noticed the problem with Ubuntu 9.10 and 10.04. I feel like a problem regarding the bootloader version. AFAIK, 9.10 and 10.04 is using GRUB2 when 8.04 use the old version of GRUB. Will I have to switch to the legacy GRUB? (I would love to keep using GRUB2). If yes, I would like to know How.
I'm having an issue installing Ubuntu with Windows 7 Home Premium 64-bit through Wubi. The Wubi installation works great and Ubuntu seems to install after the first reboot after selecting Ubuntu from Windows' boot menu, however whenever I select Ubuntu from Windows' boot menu after Ubuntu installs and it reboots for the second time, it loads the GRUB bootloader, however Ubuntu isn't listed at all.
Windows 7 is listed twice and Windows Vista is listed (seems it picks up the recovery partition for Windows 7 as Vista) and when I select the first Windows 7 from the GRUB bootloader, it just goes back to Windows' boot menu with Windows 7 and Ubuntu as the selections. If I select the second Windows 7 from the GRUB bootloader, it'll boot Windows 7 like normally. It looks like Ubuntu is nowhere to be found. Because of that, I just ended up uninstalling it.
I'm trying to install ubuntu 9.10, downloaded the iso from the site and burned it on a CD, but when I boot from my cdroom drive and choose install ubuntu option I get an ubuntu grey logo for a couple seconds and the I get this error:
I tried downloading a new copy and burning a new CD but still have the same error, no matter what option I choose when booting the CD.
Does anyone now whats the problem? What I'd like to do is install linux as the only OS (formating everything else) not dual boot or anything, I'm new to linux so it'd help if you guys could give me details on how to fix it
I have installed previous versions of ubuntu on this same computer but using the wizard inside windows.
after every update extra fedora link generates at bootloader menu , till today i updated thrice and 3 fedora with diferent version is comming up at the boot menu along with other (win7) so if i updated f14 100 times then 100 fedora link will come at boot menu or what ?
I just tried to install OpenSUSE 11.3 on sda4 which is approximately the 2nd half of a 1TB drive, with a pre-existing Win7 installation on the 1st half. The installation summary (before it made any changes) told me "The bootloader is installed on a partition that does not lie entirely below 128GB. The system might not boot." Naturally, not keen on having a computer that won't boot, I aborted the installation.
Of course it's not below 128GB -- Windows is there.
Is there a workaround that is straightforward enough for someone who has very limited experience with GNU/Linux and isn't a comp-sci student?
I am trying to install Ubuntu to an external usb hard drive (WD Elements SE). I am also choosing to install the grub bootloader to this disk (/dev/sdb) because I do not want anything modified on the internal drive. The installation appears to go okay, but when I try to boot to the usb drive, I get the error, "no boot sector on usb device" and it immediately falls back to my interal drive. I have tried this installation with both 10.10 (amd64) and 11.04 (amd64). How can I fix this?
Just installed Ubuntu 10.10 onto my new netbook from a USB stick. The laptop came with Win7 Starter, which I kept on a small partition. Installation was apparently successful, but when I start up the computer, it will go straight to Win7 and GRUB doesn't appear.
borked the bootloader by my own doing. When I got this machine, I had a single HDD. I partitioned it with a primary partition for Windows, followed by an extended partition with swap, /home/ and /, as well as a FAT32 partition for "general" data. (this was before NTFS write support was common) This worked well with the Win2K install. Eventually, I added a second HDD, which became part data storage, and part Windows XP install. I eventually put Win7 on it, and pulled the other HDD during setup so that the boot order of the drives determines whether I boot Win7/XP or get GRUB.
However, my "data" partition was not visible in Win7... It shows up as an unknown FS in the disk management. OK, I thought. I used Paragon partitioning software to move the "data" partition out of the extended partition and make it a primary. I could now access it from Win7. I didn't realize I had GRUB set to boot from the extended partition, so now when I boot from that HDD, I get "no operating system". No problem, I thought. I'll pop in the install CD (NET), use it to boot the installed 11.3, and run the boot loader setup. Nope- setup just hangs. Tried it with an 11.2 DVD... doing a "boot installed system" nets me a few moments of searching, "evaluating root partition", and then "no valid linux install found". Trying the boot loader reinstall from there nets me an "error changing to target environment" and the install fails.
I can still mount the / partition via rescue mode and all files appear to be intact, so I don't think I've lost any data... just grub/the MBR is borked. I've already moved the data partition back in to the extended partition but no luck. Still the same story... thus I'm stuck booting Windows until I fix this.
i installed ubuntu after windows 7 but now i cant boot windows 7 i tried the start up repair and I've read through some questions answered on here and int figure out the problem i don't want to uninstall ubuntu unless it's my only option
Currently I am running a dual boot with Windows 7 and openSUSE 11.3. Windows has two partitions, one for the system partition and another for the OS. I have 3 Linux partitions (swap, root, and home). Obviously I am running GRUB to boot, but this seems to be impacting my ability to install Windows 7 SP1. I would like to revert back to the Windows boot loader, install the Service Pack, and then revert back to GRUB. How do I do this?
i've been using ubuntu with wubi, and I'd like to install it on my new hard drive (so windows is on one hdd and ubuntu is on another). afaik, grub will be installed on the hdd w/ ubuntu, and i have to set it to recognize the other (windows) hdd. assuming that i want to get rid of ubuntu and just use windows, what steps do I have to take to do so? (if grub is only on the ubuntu hdd, then would I just have to format it?)
I installed Ubuntu 10.10 amd64 (and tried 10.04.2 as well) from Wubi under Windows 7 64-bit. When I reboot after installing it through Windows, I go to Ubuntu and the installation completes. Then it reboots again to finish the install of the OS. When I boot into Ubuntu now, grub does not appear. Instead, some initramfs stuff comes up in a console with no GUI and says some error stuff about root devices. I read that grub updates cause problems, but the installation never finished and therefore I was never able to go into Ubuntu to lock grub packages, etc. I've run into this error on multiple fresh installs.
i have ubuntu 10 and win 7 dual booting on one hdd, all of a sudden grub says error no such partition when i select windows at the boot menu. and i cant get to the win7 partition from ubuntu (to play music and stuff, this used to work, places, mount filesystem, 250 gigs whatever). i've tried the stuff in these links and nothing has worked so farpartition info
sudo fdisk -l /dev/sda Device Boot Start End Blocks Id System /dev/sda1 1 29094 233697523+ 7 HPFS/NTFS /dev/sda2 * 29095 30401 10498477+ 83 Linux
I am helping my pal to get into Debian (yes first timer).He is running W7 on a 500G SATA HDD and he has another 250G SATA HDD that he wants Debian to go to.Will Debian install grub on the master bootloader even if the installation is going on a separate hard drive?I have dual boot before but on the same hard drive.
I am just starting to learn how to work with a Linux OS and was planning on using a bootloader to start my PC so that I could choose which OS I wanted to start, enabling me to mess around with them without needing to worry about hosing my system.Also, my studies are taking me deep inside how the Linux OS system works in general and was hoping that I could also get some advice on where to start separating GNOME from the OS to find out exactly how they work together, how the OS works with services, etc. because I am trying to learn everything that this entails.
I recently installed Lubuntu to a USB. It was up and running and worked fine, however, upon exiting and going to boot into windows, I noticed it had installed a GRUB bootloader. I use whole disk encryption on windows, which has its own bootloader, so I can't be having some other bootloader on the PC interfering with this. I used my rescue disk to restore my WDE bootloader, but the USB stick will not boot now.
I also tried using pendrivelinux but this copies the live cd version onto the USB stick and nothing saves when you log off.installing Lubuntu to USB without a boot loader?
I have two installs on the same drive but different partitions. First I installed XBMC live which is based on Ubuntu (I don't know the exact verion but I think it's in the 9.x).Then I installed full Ubuntu 10.04 on another partition. Now it uses grub2 off the second partition. I configured it to boot XBMC as default and I've had no issues with it. However in the end I rarely use Ubuntu since this is really HTPC. I thought maybe it would be cool to check emails and do some web browsing on my TV, but it turns out I prefer just using a regular computer for that. So I want to delete the partition, but I'm worried doing so will make the system not boot anymore unless if I reinstall XBMC live, I don't want to do that either since I've got it configured all properly and I don't want to mess that up. So I believe I have to change the MBR to point to the XBMC partition although I haven't quite figured out how to do that.
I am installing version 10.10. Does it matter where I install the bootloader? There are selections for the entire device and each partition. I have Windows 7 on /dev/sda1 and Ubuntu on /dev/sda3. The last time I tried this I couldn't go back to Windows 7 even after using the grub-update commands.
I tried to install Ubuntu 11.04 via .iso + USB key to my Asus EeePC 1000HE. This computer comes with two partitions already on the hard drive so I installed to the empty one, to dual-boot with Windows XP on the other. Installation seemed to work, but after resetting, the computer always boots straight to Windows, not Ubuntu or an OS list.From my Ubuntu boot USB, sudo fdisk -l shows that the installation wrote to the partition successfully.From Windows, the partition appears to have disappeared.So it seems that the installation worked except that I have no way to boot to Ubuntu.
I have seen multiple others with this problem, I now have it too. I had Ubuntu 10.10 installed on my entire disk, then I installed Fedora 15 with it. The resizing-the-disk went smoothly, everything is great, but now when I turn on my machine, I get no grub, no boot loader, nothing. I just get thrown right into Fedora. I saw on a few other posts that if you manage to get into Ubuntu, you can open a terminal and type something along the lines of sudo grub update, and that would do the trick. The only issue is that I can't even get into ubuntu. I also was told that if you boot from a livecd you can edit the boot config, or view it, or something. I'm pretty new to all this "bootloader grub" jazz, and am hopelessly confused. How do I make it so that upon startup, I am able to choose between Ubuntu and Fedora?
I've recently installed an Ubuntu Netbook Remix on my netbook and I'm trying the same on a desktop with a desktop distribution. I've a strange issue : I get to the start menu with the "Try ubuntu", "install ubuntu" and so on.
When I choose try I get a popup with title "Boot loader" containing the word "live". When I choose to install, I get the same popup with "live-install" as content. I don't find much on the web.
I recently installed Fedora on a triple boot system with Winows XP and Ubuntu JJ. how to add Ubuntu's grub to the bootloader. Here is the output of Fdisk -l.
[root@localhost rabbit]# fdisk -l Disk /dev/sda: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes
I am trying to install Ubuntu10.04 on my machine which already has on it, Win XP. Lemme lay down the setup of my machine first of all.
I got a new 320GB HDD of which I have taken 20GB as the primary partition and installed Win XP on it. Took another 220GB as an extended partition for my data storage. Around 63GB was remaining which I left it as unallocated. Decided to try Ubuntu, but preferred to boot it from the windows bootloader. Downloaded and burned the Ubuntu-10.04-desktop-amd64.iso(have a AMD x3 425 machine) and tried an install on 30GB of the 63 left.
I did not try any partition scheme. I chose the manual partition option, made a 28GB ext4 partition, made it primary, mounted the /, took another 2GB for the swap and proceeded. Chose advanced option and installed grub on the 28GB(/dev/sda6) and completed the installation.
Since no grub was installed, Ubuntu was not available. So then, used the bootpart utility to point grub to the windows bootloader, but it did not work, was giving me error when I chose Ubuntu from the bootmenu modified by the bootpart.
So tried booting with the same install cd, chose Live Ubuntu this time and mounted the 28GB, copied the first 512bytes using dd if=/dev/sda6 of=ubuntu bs=512 count=1 to a usb drive. Rebooted into windows and copied the file to C: and added it to the boot.ini. Rebooted and tried choosing Ubuntu from the boot menu but it does not work. I get a blank screen with the cursor blinking.
The machine is new and BIOS is LBA enabled by auto.
i had a dual boot xp/ubuntu first. later i had to format and reinstall xp. this deleted the grub bootloaderplease let me know, how to fix this! please make it simple . i have the live cd, but i don't have internet connectivity in ubuntu.
