Ubuntu Installation :: 10.04 LTS (Wubi) - Blank Screen On IBM Laptop
Jun 27, 2011
There is an installation problem when installing Ubuntu 10.04 LTS using Wubi on my IBM Thinkpad R50e. My operating system is Windows XP Professional. After Wubi installed the Ubuntu Installation Files on my hard drive, I restarted my computer. After restarting, I selected Ubuntu on the selection of operating systems.
First, I saw the introductory logo of Ubuntu (when the ubuntu loads its files). After that, instead I will saw the installation progress or the installation of language packs, only Black Screen will appear on my Laptop screen. I have waited for an hour, but nothing happens. It did not pushed through with the installation.
The wubi installer copied files successfully and asked for reboot. After booting into Xubuntu the flashing logo appeared for a minute. And then the screen looked as if it was trying to show something but could not and flickered and then became dark this continued till half an hour and then I pressed Alt+Ctrl+Del.I tried all the modes but to no avail, only the last mode with command line was working. But it was not helpful for me becoz I dont know most of the commands.When I tried "Verbose Mode" as directed by the WubiGuide - Ubuntu Wiki, CTRL+ALT+F2 did not work when the installer stopped.The computer I use is assembled with Intel pentium 4, VIA chipset and Mercury(Kobian) motherboard.
My laptop: MSI AMD Athlon 64x2 Nvidia GeForce GO 6100.
I've done a fresh install of Ubuntu 10.04 and I end-up with a blank screen. I've also tried a fresh install of Xubuntu 10.04 and Kubuntu 10.04 and I get the same blank screen.
Ubuntu 9.10 was working perfectly though. So what do you think happened?
I installed the Ubuntu 10.04 livecd on my desktop and it works perfectly so I think it is not a burning problem.
I am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
I just installed Ubuntu 9.10 CLI with Openbox as the WM on my Dell laptop. I installed gnome-power-manager because I like to suspend my laptop when the lid is closed. When the close the lid and reopen it, the screen is black and the computer never suspends. This happens regardless of whether or not gnome-power-manger is running is the background.
I have Ubuntu 10.10 installed on a laptop. The laptop has an external 19" screen connected to it through the VGA port. I am not using the laptop screen (because it is small and flickers constantly) but only the external screen. When I shut the laptop lid the external screen blanks. There is no option in the power management dialog and the option "Activate screensaver when idle..." in the screensaver dialog is unchecked (which I would like to re-enable to blank screen when idle for x minutes). How can I get Ubuntu to leave my external screen on when the laptop lid is closed?
I just installed Linux 5.5 on a Toshiba laptopn (i3, 64 bit). Centos runs until it reaches a very dark screen. On a few occasions, I am able to see something but the screen is very dark.
I'd like your input on this. A toshiba laptop screen goes blank after few seconds(from turning on).
At first i thought it was fan that was out and once it got hot enough it cut the laptop off like my old Acer did.
But after close examination i noticed that it continues working. HD still spining and fan blows..
Example: Turn on>Hit F2 to go in to Bios> Bios screen appears>Before i have a chance to do anything it geos blank but continues working> I hit Cntrl ALt Del> it resets and screen comes right back up>second later it goes blank again.
ALSO the toshiba logo and whole screen seems to have a red tint to it.
I also get a media test error but that is likely from hard drive not being there during some of the tests.
DO you think it can be an LCD Backlight issue? or possibly video card?
I am running Debian 8.3, and I'm running Gnome 3.14.1.I have an external monitor plugged in with HDMI, and while Linux is loading both screens are on duplicate. Once the GUI kicks in, only the external screen works, so I have to enter my password blindly. Then, I open a terminal and run
I'm using a dell latitude d630 with an nvidia quadro 135M card. I'm able to suspend without any problems while running the X server. If I try to suspend on console without the X server running, the laptop wakes up to a blank screen. The screen remains blank and my only resort is to type sudo halt (with the screen off).I'm using the proprietary nvidia driver with the nvidia-kernel package on testing.
Is there a known problem with the Lubuntu 10.10 image here? I have downloaded it to two different computers, then burned the images to two different blank CD's (different brands) and neither loads. Both only get as far as the Lubuntu menu, once ENTER is pressed at that point to load the LiveCD, a blank screen eventually appears with a flashing cursor at the upper left of the screen, that's it. They were both burned using the slowest burn speeds available.
i just tried to install Ubuntu 11.04 (x86) on my Dell Inspiron 1520 Laptop (with a Nvidia 8600M GT graphics card) with Wubi. A normal installation try resulted in an unreadable screen after boot (see attachment). I then managed to get the installation going by modifiing the boot options like shown in this HowTo: [URL] After the installation Wubi automatically rebooted the system without any prompt, so that i couldn't install the proper Nvidia drivers (is there a way to prevent wubi from doing that?) like described in the HowTo. After the reboot the graphics were messed up again.
Boot parameters like "text" "single" or vga=xxx didn't work, adding nomodest and nouveau.modset again didn't help either (I think "text" acutally brings up the console, but i just see an unreadable "blacker" screen than normal). Is there an boot option for grub to disable all nvidia related drivers and the graphical login manager and just show a text based console? Or force the gfx driver to be the same as in the installation process (which was perfect...native resolution, no graphical errors until the reboot) (i tried xforcevesa without any luck; nosplash and removing quiet/splash does work - the bootup process is readable, but as soon as the login manager starts its messed up again)
I have been running 10.04 quite successfully, when I upgraded to 10.10, I have a problem with the newer kernels. If I let it boot into the latest one 2.6.35-23, I get the Ubuntu 10.10 splash screen for a second then a blank screen, same with 2.6.35-22. I have to run with 32-25 to get it to load the gui.
I have an AMD Sempron 2800, 1.6GHz pc, but I'm not sure if it's running 64bit.
I've been running Ubuntu 10.10 very smoothly for a while now. Decided to upgrade to 11.04 - managed to corrupt the hard disk the first time by letting the laptop hibernate part of the way through but reinstalled from a live CD of 11.04 and it's now working except for this issue.
If I shut the screen on my laptop (or press the screen off button) either the screen won't come back on or it will but frozen (I can move the mouse but not click on anything etc.) In this state music continues to play (from spotify under wine) and if I press my hibernate shortcut (power button) the computer hibernates, only to wake into the same situation. I've got a Dell Latitude D520, upgraded to a bigger hard disk and more ram - the ubuntu partition has 50gb. Windows is working fine.
Edit: I noticed a sticky thread which includes something about a blank screen but I think this is a different issue?
When I installed Kubuntu 11.04 using Wubi it did not load the Ubiquity installer like it normally does. Instead the boot screen (image attached so you know what I mean) remains displayed for the entire installation. The installation works fine once installed but I was wondering if this is normal or not?
I have installed Ubuntu 11.04 along side windows 7 ultimate. But the problem is as soon as I switch on my computer. There is only a blank screen with my TFT screen displaying a msg "Out of Range"
Then suddenly Ubuntu loads without showing any option to load windows 7.
So finally decided to upgrade the desktop (dual-booting with Windows 7 for games) from 9.10 (fresh install awhile ago, never did anything with it) to 10.04 - upgrade went fine, reboot, watch grub go by, and voila. Blank screen.
I was hoping to test out Windows 7 in a VM, see how far I could get for GPU acceleration there - I'd much rather not run Windows on the bare iron for that machine, but if I can't get this fixed I have no option :-/
I'm installing Koala here on a 250gb Sata drive. I am looking to dual boot with Win7. I've got a 80gb Win7 partition and the rest is unallocated so I can install Ubuntu on to it. If I try to install, I get to the manual partition screen and it's blank. From what I can tell, Ubuntu isn't recognizing my hard drive at all. When I boot into the liveCD and run gparted, it says no devices found. Also when I boot gparted from a cd I get the same thing. BIOS sees the drive fine and the drive boots into Windows fine.
When I run "sudo fdisk -l" I get nothing. I've tried several of the flags including all-generic-ide. Also tried removing dmraid.
I recently got a new laptop and am trying to install Ubuntu 9.10 on it. I have installed it on my two other computers without any problems, but there seems to be a hitch with my new one. So I boot up using the live CD and then am presented with the option to test Ubuntu or install it. If I choose either of these the screen just goes blank. If I go with the first option of testing Ubuntu before installing, I can hear the intro drumbeats but the screen is still blank.
I have searched in some forums and tried some people's advice, like pressing Ctrl+Alt+- or trl+Alt+Backspace to change the resolution and restart X windows, respectivley. But it doesn't seem to work. I'll list my laptops specs just in case my problem has anything to do with them:
MSi Windows 7 Home Premium 32 bit Intel Core i3 M 330 2.13GHz 4GB DDR3 RAM Intel Graphics Media Accelerator HD
Ok well this is my first post on the ubuntu forums and the problem I have is, hopefully, pretty simple to fix. When I am installing Ubuntu, I go through all of the steps and once it asks where to install and partitioning and all that I tell it to erase the entire windows thing and put in Ubuntu. So I click the Forward button and when it gets to 69% of copying files, the screen goes black. It sounds like its still running the install but I cant be sure. What should I do?
I've found similar posts to this but none seemed to be solved. I'm trying to install ubuntu 9.10 on my new laptop. Dual boot Win 7 Pro on first partition.Its a gateway nv79 laptop with an intel i3 330M processor.The problem occurs when I boot from the CD I get the first menu where you can choose to install, load ubuntu from CD, etc. No matter which option I choose, I get nothing but a blank screen. Then I can do nothing but power down by holding the power button.I've tried both 64 and 32 bit versions, same thing. The 32 bit disk works fine on another computer. I've also tried booting another version of Linux, Helix, from CD and that also works fine. I'm thinking ubuntu doesnt support my graphics card: Intel Graphics Media Accelerator HD
I'm trying to use the live cd on my HP Pavilion Entertatainment laptop, but I get a blank screen. The Ubuntu logo shows and I get to choose my language, but when I click on "Try Ubuntu without doing anything to your computer" (paraphrased) the screen goes blank. About a minute later I hear the Ubuntu music.
I did a fresh install of 8.04 alternate disk with LVM then updraded to 10.04 (due to lack of any spare CDs around).
Everything was working fine but wanted to try to get the nvidia-173 drivers installed (I have an old FX5200). Can't start into X now as my plasma says mode unsupported.
At one point I managed to boot into recovery mode then root terminal and removed all nvidia packages and reinstalled nvidia-173 only and followed the instructions listed on the 10.04 release candidate page. Still stuck with the unsupported modes error on my TV though. I have a 720p plasma display (1366x76, I usually run 1280x768 without issues. I'm guessing it is the refresh rate set in the new xorg.conf that is throwing me off, how to adjust this?
An issue that's complicating things however is that when I try to boot into recovery mode I get an error stating 'pcspkr' driver already registered, aborting... then it hangs there until I ctrl-alt-delete and force a restart. This is preventing me from getting to the point where I can select a a root terminal to try to fix my errors.
I have used 8.04 exclusively for a few years and wanted to try something new (still not all that adept at linux setup).
EDIT: I managed to get to root again and just removed the xorg.conf file and that seems to work somewhat. Except now I can't boot as I get a looping mountall: Plymouth command failed that hangs up the process.
I've been using Ubuntu off and on since 6.10, but I am definitely a noob when it comes to troubleshooting this kind of stuff. All of my previous installs went flawlessly, so I guess I've been lucky so far. I finally decided that I would bite the bullet, and remove Windows altogether. No more dual-boot with XP or 7 for me.I've been attempting to install the 10.04 RC all weekend, and it's been pretty frustrating. I decided I would start with my aging laptop, a HP Pavilion ze8500 that I custom-ordered way back in 2003. A few specs I know off the top of my head:
P4 (2.30 GHz) 512MB RAM 40GB SATA HDD
I burned the ISO to CD-R and started the install. When I boot from the CD, I get a purple screen which is blank other than two symbols at the very bottom. IIRC, one looked like a ruler or something, and the other looked sort of like a star in a circle? I think they were separated by an equal sign.I have no idea what that meant, but I knew enough to hit F6 and that got the install menu to appear onscreen. The only way I could get through the installer without losing video was to use 'nomodeset'
I installed over top of Windows 7 RC with the default partition table settings and after the install finished, I got the dialog box telling me that a restart is necessary. I hit Continue, the CD tray ejected, and my laptop restarted.So, assuming that the installation was a success, I see the BIOS screen, and then that goes blank, and where I would expect to see a boot screen or a Grub dialog, I see nothing at all.After the first install attempt, I would hear a drum sound after the screen went blank.I tried hitting 'Esc', along with 'Ctrl+Alt+F1', 'Ctrl + Alt + F2' or whatever else I could think of, and nothing seems to work.I updated my BIOS, remembering that I forgot to do that, and then I reinstalled Ubuntu. Again, no display when Ubuntu boots. And now, I hear no drum sound at all.
So I tried to install ubuntu 10.04 on my 5 year old gateway laptop but the screen kept going blank when ubuntu was booting up. I was able to get to the menu screen and add "i915.modeset=1" after "quiet splash", which allowed ubuntu to load. I installed it on the hard drive successfully, but when I restarted the computer, it won't load again. I don't know how to fix this so I can run it from the hard drive.
I'm attempting to install Ubuntu Netbook remix (however I have tried others) on a 32 bit laptop but after it goes through that ubuntu loading thing, it goes blank after that and I've determined that it's not the cd and it's something to do with the hardware after looking at other posts with similar issues. I do not have an operating system on this laptop.
I've searched the forums and all the problems seem to be getting a blank screen after the first menu or first splash screen.My problem is that I'm getting a blank screen straight away without seeing anything. As soon as the system says that it's booting from CD the screen goes blank and nothing happens.I've done the md5sum on the disc successfully (and the iso). It's an old system (P4) and I'm using the integrated graphics.I've tried Ubuntu Server 10.04, UNE 10.04 and Ubuntu 9.04, all have the same problem.
I have an HP computer nvidia and AMD stickers on it and 1GB RAM. HDD is Parallel ATA. I downloaded both Ubuntu & Kubuntu Live CD. Both live CD's boot to a blank screen. After a (seemingly) successful install of kubuntu, the screen goes blank after GRUB.
Here are the details: With this HP, when i boot from ubuntu live CD the screen goes blank. It does not give any option about trying ubuntu, install, ubuntu, mem test. I just get a blank screen. On my ASUS laptop the ubuntu live CD goes straight into ubuntu live (without having to choose an option). It is not the CD When I boot from kubuntu live cd i get to the screen where i have an option to try kubuntu, install kubunt, memtest..
If I choose either try or install, my screen just goes blank & never progresses. Again, this live CD works on my ASUS laptop. At the bottom of the boot screen for the kubuntu live CD i noticed f1-f6 configurations. I was unable to change any other than language and f6 options. If I press f6 i get options which i can mark with an x. I don't know what any of these mean but I checked all of them and then on the boot menu popped up
BOOT **a whole bunch of text** I went onto install kubuntu and it no longer went to a blank screen. Rather it was a fuzzy grainy splash with the word KUBUNTU and loading dots underneath. Atlas it seemed to prevail, the installation process started (fuzziness went away). The installation screen now looks just as it did on my ASUS laptop. I continued through the steps with an installing on the entire HDD. The installation completed (with no signs of error). Screen said take out disc press enter.
I did so and my computer turned off. I power up the computer and the GRUB loads up. I have option of regular and fail safe. Both lead up to a blank screen. My monitor seems to think there is no signal and goes into standby mode. Perhaps the video card is not rendering correctly or not compatible.
ive tried to update my test-laptop (thinkpad t43) to the actual beta. the dist-upgrade worked whitout problems, but after rebooting the x-server seems to work, but screen is empty...it seems that the xserver is crashing:
Quote: Caught signal 11 (Segmentation fault). Server aborting here the full log: Quote: [ 181.280] X.Org X Server 1.9.0
