I am trying to boot up my computer which has the Ubuntu 11 beta AMD 64bit, but before I can reach the login screen I get a black screen with the word "Killed" in the top left-hand corner. If I attempt the recovery boot I get different messages.
View 9 RepliesI'm using debian for the first time and I recently downloaded the Debian Lenny 201 Live CD to test it on my old computer (I'm planning to use Debian 5.0.4). It has a Pentium III (550 MHz) processor, 192 MB RAM, 8 MB graphics memory, 20 GB HDD with a monitor supporting 1024x768 resolution. The problem is, after the booting is complete a blank flashing screen appears with a cross-shaped cursor in the middle. I continues and nothing happens. I tried with solutions like editing the entries with 'live xdriver=fbdev', 'live xdriver=none', and 'live vga=771'.
View 10 Replies View Relatedi just installed slackware 13.37 which worked fine but when i boot it up it runs a number of lines and then the screen just goes black... i can login as root blindly and start x (i THINK, judging from hdd led)... but screen stays black... its a laptop and closing/opening the lid doesnt work either...
i am dualbooting with slack 13.1 which runs fine... it switches screen res at some point during boot (font is smaller) and i would say that is the point where the screen goes black in 13.37...
Pretty much what the title says.. a few more details:
- I installed 10.04 using the alternative install so I've been doing all this in safe mode
- I installed a newer kernel (2.6.33) and still black screen
- I tried to install an updated Intel xorg driver, but I kept getting dependency errors (xorg, x11, something else)
I read another thread on this forum from a user who is using the same platform (Intel HM55), and I got stuck at the last point (can't get Intel xorg driver to install).
I am trying to boot up Linux Mint 7 after a packages upgrade and it boots up but then it shows this and stalls.And similar messages for GDM and then it just shows a black screen with a single blinking cursor on the middle left of the screen. I cannot do anything except press the CTR-ALT-DEL combination to re-boot, then it shows the usual shutting down messages and does the re-boot.I am running the 2.6.28-19 kernel and I have upgraded the Ubuntu packages on my Linux Mint 7 system from Jaunty to Karmic. Please help as I do not want to re-install. I am running Knoppix 6.3 ATM and I should be able to chroot from that if necessary. I am booting from /sda1 that has Linux Mint 8 installed and grub 1.97.
View 1 Replies View RelatedI was messing around with the screen orientation and thought it would be funny to orient it sideways. Big mistake The screen went black.I can force a shutdown, login and I get the same black screen. I tried hooking up an external monitor and the monitor showed no input so I'm guessing my laptop doesn't have that capability with Fedora.This is my main computer.
View 14 Replies View RelatedI have a customer that was raving how he likes windows 7. I asked him what he saw improved over xp, and he could only list the mouse hover preview of tasks in taskbar and media player could show all songs with word black in title. I am training my 3 and 5 year old on Ubuntu, and they (& wife) cannot grasp the difference between bottom taskbar and top applications menu. Even on my xp machine they freak out (including 10 year old with computer classes) when I minimize their applications to work on my own when they get up from the dining room machine.
And, so I though I would download "Visual tray tip" which mimics the taskbar preview on mouse hover. But on my 6 gig hard drive, p3 650 mhz 1 gig ram living room notebook (mainly flash educational gaming for kids) I really would like such a task bar preview. But upgrading Ubuntu is out of the question, since it is a functioning machine with 211 megs free on drive, and I have no stomach, time, or wish to kill it by an upgrade. So, am wishing for a sudo apt-get install solution.
10.04 - Installing splashy fails and consequently makes kpackagekit completely unuseable. Attempting to fix this with aptitude or 'sudo dpkg --force-overwrite --install' or 'sudo apt-get -f install' (as suggested elsewhere) brings me no joy either. Is there a fix so I can remove splashy and repair kpackagekit? How do I kill splashy so i can repair kpackagekit?
View 5 Replies View RelatedI pressed crtl + alt + f9 on my system and it went to a blank screen. I tried to get it to go back but it wouldn't so I rebooted. Now no matter which kernel I select from the GRUB, even in recovery mode I get the same blank screen and after a few minutes it says
Code:
I tried to use the "Rescue a broken system" option on my live cd but as far as I can tell its just a text installer and I can't fix this problem with it.
I can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedThis is my sons Asus eee pc 1005peb ( have one exactly like it and never happened to me)
The screen flashes on bootup and makes it very hard if not impossible to login and the gnome menu at the top is gone too. I do not know what he did to it. But I am loading meego on it now.
Have installed Ubuntu 10.10 on a couple of Dell Inspiron 2650 laptops (both 512M memory) and when they run, they're great, but they only successfully boot up maybe 10% of the attempts. Most of the time, the touchpad and keyboard are inoperative, but I recall sometimes the enter key gets me past my user Id to input password. Trying to enter recovery mode isn't any better, but once into recovery, I'll boot up in safe graphics, but it is probably only running because it succeeded in entering recovery, anyways. I have elected to to boot up in safe graphics, but they still both freeze. No error messages, just a frozen background/icons screen.
Ubuntu has searched the hardware and reports there's nothing requiring proprietary drivers installed.
After reading all the other problems posted, I figure my laptops are doing pretty darn good, but it sure would be nice not to set around starting up and shutting down, over and over.
When I boot up 9.10, very occasionally, I get a login screen directly after the page with the Ubuntu b&w symbol and before the colour page. It doesn't happen very often but usually when I am showing someone how good and quick Ubuntu is.
View 8 Replies View RelatedI installed Ubuntu via Wubi, but now when I boot up the computer, it asks me to select Ubuntu or Windows, then after I select Ubuntu, it takes me to the Grub menu, which also asks whether I want Ubuntu or Windows. I've had this on multiple computers, and it's not very useful. How to change this?
View 2 Replies View RelatedI turned on my Acer laptop and during bootup it seemed normal. After it passed the blue Acer logo, all I could see is a black screen and a black cursor outlined in white in the shape of an X. Thinking it would be a one time thing, I turned it off again.it still was a black screen.
View 14 Replies View RelatedI have a pc with 1 GB RAM,Intel Core Duo CPU(1.86 GHz).Recently during formatting of the pc with new windows , I (accidentally)powered off the pc during the process.Due to which what has happened is there is no screen during the time computer boots up when switched on.Only when there is a login window,the screen becomes active.I even installed UBUNTU (which I am still using) on the whole hard disk but problem persists.The problem seems to be independent of the OS.
View 2 Replies View RelatedAfter grub loads the kernel I'll get an on screen message from the console showing: cannot reserve MMIO region And I was wondering is there a way to silence console messages so you don't see them at bootup?
Could setting dmesg work:-nlevel Set the level at which logging of messages is done to the console. For example, -n 1 prevents all messages, expect panic messages, from appearing on the console.So typing at a term 'dmesg -n 1' will work?
I have Lucid running on a Toshiba Portg R500. Last week it started hanging for just over one minute at the initial Toshiba screen. That is, the screen with the Toshiba logo and a series of boot-from options (HDD, CD, Network, USB) along the bottom. I don't know if the machine is even interacting with the OS at this stage. Also, neither Ubuntu nor the machine recognises the CD-ROM tray any longer. As in, I can't boot from CD and I also can't mount a CD when in Ubuntu. I can, however, boot from a USB startup disk (after the one minute delay).
I'm not sure how to collect helpful data on this sort of issue, especially since I can't see any threads that point to similar problems. The only strange thing I did the day this problem started was to forget to unmount a truecrypt-encrypted USB key before shutting the laptop off.
I've reinstalled Lucid but to no avail. I assume that whatever problem I have is a BIOS problem (and so strictly not for here)? As you can imagine though I want to make sure I've accounted for all other possibilities before fooling around with the BIOS.
I installed lubuntu 10.10 on my old computer (pentium II, 192 mb ram) but when i try to boot it passes the purple screen and feezes just after showing:
* Starting AppArmor profiles [OK]
* Starting NTP server ntpd [OK]
It was installed on From liveusb with the harddrive plugged into another computer cus the old ones bios doesnt support usb boot.
I recently got a new laptop (Aspire 5741) and have installed ubuntu 10.4 on it. I have been very happy with the computer and OS. However the only problem I have had is that I am unable to change the screen brightness. Last night I though I found a fix. I cant remember the specific thing but it was something similar to this [URL]. On reboot the ubuntu logo came up and a few seconds later it showed a distorted ubuntu logo. After this it just goes to a black screen. I have tried booting into recovery fail proof graphics mode, and the problem still arises.
View 3 Replies View RelatedI've upgrade my fedora 11 to 12 by installtion DVD and everything is fine right now.Everything is there and the new system looks good.However,my boot screen is still the same with 11.How can I switch to the new screen?
View 12 Replies View RelatedI have a clean install of slackware 13.37, downloaded today from slackware64current. On boot, I get a black screen - not just black, but no video signal out of the video card, or at least nothing that the monitor recognizes. Fortunately, I can ssh into the box from another machine. If I do, I can startx and xfce starts up and appears as expected. lspci shows:
01:05.0 VGA compatible controller: ATI Technologies Inc Device 9714
02:00.0 VGA compatible controller: ATI Technologies Inc Device 6898
I have an onboard video chipset with a monitor connected to it, and an ATI 5970 in a pcie slot with a monitor also connected to it. xfce appears on the pcie card (the 5970) as expected, as this is (supposedly) the primary monitor, and the monitor connected to the onboard video output is blank - no signal, also as expected as I have not yet installed the ATI drivers. So the question is - how do I get the terminal output on bootup to appear on one of my monitors? I'm not sure where it is going, and this is out out of my area of expertise.
Is there a function to use cursor pointing to some word on screen and tell what is the font name?I tried X utilities, xprop. listres, xrdb,etc. but still lost. I am trying this because some font is missing in Exceed but OK using local Xserver. I'd like to copy the missing font to PC and get readable text in Exceed.
View 3 Replies View RelatedI have 9.04 installed. When I boot up i see all the iterations since the 1st install on my boot up screen. How do I delete these? I have to scroll to get to my other OS's.I am running a multiple boot setup.
View 3 Replies View Relatedwhen trying to startup Ubuntu 10.04 the screen goes blank and says no signal. But there are three Ubuntu's to chose from. the middle one will boot-up and works all right. But for when it is starting up the screen flashes and comes back on. the top one doesn't work at all screen goes blank but the lights on tower stay on.
the bottom one starts to boot but when it gets to the screen for your id and pass. it goes all blank but for a white line on the right side of the screen. this is on an old e-machine with a dual boot windows xp home. currently with 1g of ram and a 160gb hard drive split in two. with an AMD processor and ATI graphics on board. cant remember the numbers after that come after Ubuntu on the grub it is listed three times. how do you remove the other. let me know if you need more info.
I get a blank white screen when i try to bootup fedora and ubuntu to install them. I don't know whats wrong, any ideas?
View 1 Replies View RelatedI just installed 11.3 on a Toshiba Satellite A305 laptop. After going through the install process it restarted (without a full reboot I believe) and spent a very long time going through a bunch of message. E.g. it spends about 10-15 minutes building java fonts, and warning me that Japanese/Chinese/Korean might not work in Java.About 20+ minutes after bootup it finishes with all the status messages (including a message that said it couldn't execute /usr/bin/cmp !?) and goes to a blank screen with a mouse sprite -- first a spinning circle, then a regular arrow sprite. So it's not a totally black screen, but all I have is the mouse sprite.
I let it sit there for over an hour.I think it was hitting the disk but nothing happened. I tried rebooting and it did the same thing.I tried setting the "nomodeset" boot parameter, which had helped someone with a similar problem no change.I tried it in failsafe mode no change.
Is it possible to create a custom bootup splash screen, either a bitmap graphics file or just a simple text file. I'm not talking about the BIOS splash screen nor the boot loader input splash screen, but rather somewhere in between, i.e. when the HDD is detected as the boot drive, a splash screen is shown. I'm trying to make sort of a "rescue disk" that simply boots up to a shell, and I am wondering if I can display a custom message once the PC is booting up from this disk.
View 1 Replies View RelatedWell, I am facing one issue:How can i read two files word by word at a time using any loop as i need word by word comparision in shell script?Please let me know pseudo code.
View 14 Replies View RelatedI have a output file look like this:
{"test1" : "test2", "test3" : "test4"},
How can I read word by word in each line?This is not working code:
a=0
while read word
do a=$(($a+1));
[code]...