Ubuntu :: (10.04 Lucid) Built-in SD Card Reader Stopped Working?
Apr 3, 2011
I'm using 10.04 and it's been excellent all the way through up until this problem happened. My laptop's built-in SD card reader has stopped working out of nowhere.
Here are the basic facts:Laptop is a Compaq Presario CQ50-115NR I tried older Linux Kernels, it's not the newest kernel causing the problem. The SD card reader is not shown in disk utility anymore. It used to be shown, even when no SD card was inserted. Now? Nothing.lspci output:
Code:
00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation Device 075e (rev a2)
00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1)
00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor (rev a2)
00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller (rev a1)
[Code]...
View 1 Replies
ADVERTISEMENT
Dec 11, 2010
I am trying to disable the built-in card reader in my MBP (5,3) running Debian testing. I've noticed that powertop lists the card reader as a major contributor of wake up events and would like to disable it as I rarely need to read SD cards.
I found this with "dmesg":
scsi 6:0:0:0: Direct-Access APPLE SD Card Reader 1.00 PQ: 0 ANSI: 0
and this from "sg_scan -i":
/dev/sg2: scsi6 channel=0 id=0 lun=0 [em]
APPLE SD Card Reader 1.00 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
I don't know where to find the device in /proc and there are no modules loaded for this device (I'm guessing it has support compiled into the kernel).
So, ideally, I would like to be able to enable/disable this device without a kernel recompile. Is this possible?
View 1 Replies
View Related
Jan 1, 2009
I have an Acer Aspire One running Fedora 10.The Aspire One has a built in multi-format memory card reader compatible with SDHC, XD, Memory Stick Pro and MMC cards, however the card reader is only detected during bootup if a card is inserted otherwise the device isn't detected, the relevant drivers aren't loaded and the card reader doesn't work.
In other words if Fedora is booted without a card in the reader and I then want to use the card reader I have to insert a card and reboot in order to use it, after which cards can be inserted & removed and are detected and automounted with no problems.When the card reader is working lsmod shows the following modules are loaded.
[Code]...
If the laptop is booted without a card in the reader none this shows up. I've also tried manually loading the mmc_core, mmc_block, sdhci, memstick & jmb38x_ms modules to see if this kicks the reader into life but it doesn't. Is there a way of forcing the detection of this device during bootup?
View 14 Replies
View Related
Mar 17, 2011
System: Intel E5400 "Intel 64 Architecture for 64-bit Computing"
Fedora: F14: 32-bit version from OSDisc.com
uname gives the following:
Linux localhost1.localdomain 2.6.35.11-83.fc14.i686 #1 SMP Mon Feb 7 07:04:18 UTC 2011 i686 i686 i386 GNU/Linux
Firefox: 3.6.15 using yum
Adobe Reader 9.4.2.02/11/2011 using yum from "adobe-linux-i386" repository
Plugin listed as: Adobe Reader 9.4: nswrapper_32_32.nppdf.so
Since a week or two, clicking a link to a pdf file will not load in Firefox. I tried removing Adobe Reader and reinstalling it. Then the pdf files loaded, but now again they will not load. It just stopped working! No error messages.
View 1 Replies
View Related
Jul 18, 2011
Stuck an SD card into my laptop (acer timelinex 5830tg) for the first time today, and to no avail. I've done an lspci, but don't seem to see my card reader there. here's the output
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family HECI Controller #1 (rev 04)
00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4)
00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4)
00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4)
00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4)
00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04)
01:00.0 VGA compatible controller: nVidia Corporation Device 1050 (rev a1)
02:00.0 Ethernet controller: Atheros Communications AR8151 v2.0 Gigabit Ethernet (rev c0)
03:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01)
04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01)
05:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
I'm running kernel 3.0-rc6. Issue still remains when booting into 2.6.39 also.
View 14 Replies
View Related
Jan 10, 2010
I just did a fresh install of OpenSuSE 11.2 for my fiancee on her new HP Mini 110-1030NR, and everything works great, except for the 5 in 1 card reader. Here is the information I believe you may find relevant:
Kernel
2.6.31.5-0.1-desktop
Output of lspci:
Code:
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2)
00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series]
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
View 8 Replies
View Related
May 1, 2010
i was recently running the latest xubunto, and decided to upgrade when the upgrade manager offered me however ever since vie upgraded my sound no longer works neither does wine. I have reinstalled wine but nothing has happened but i am at a loss of what to do with the sound. It used to work with no extra configuration before the upgrade i am running a dell inspiron 530.
View 4 Replies
View Related
Jul 5, 2011
k i tried just cicking the the icon =fail then i tried in terminal
Code:
transmission enable
= fail. im lost its in system monitor but its not showing as a window or anything
View 1 Replies
View Related
May 1, 2010
User switching doesn't work for me anymore since upgrading to Lucid. When I choose "Switch From <user>..." in the logout menu on the top-right of my screen, it jumps to the login screen (gdm) but it doesn't show any usernames as it should.I wish I could get a screenshot of gdm but I'm not sure how.
View 4 Replies
View Related
May 3, 2010
i upgraded to lucid, but now my video has stopped working... videos and iplayer work fine. the problem is with any videos (mp4, flv) opened in vlc or mplayer. i can hear sound fine but the screen is black. the same happens in skype. i followed the comprehensive guide and did all the steps, but no joy.
View 3 Replies
View Related
Jul 19, 2010
My sound in Lucid was working fine (for months), and then, for no obvious reason, it stopped working today. I get no sound from any application. I have no idea what could have changed on my system to cause this.When I re-boot Lucid, the login sound plays, and sound works briefly, but it always stops eventually after I login.I am overwhelmed by the large number of different Ubuntu sound problem fixes
View 9 Replies
View Related
Oct 9, 2010
I've been running Ubuntu Lucid for six months now without problems. Last night my keyboard suddenly stopped working in any applications under Gnome. Rebooting didn't help. Mouse still works fine.But the keyboard still works fine when typing in my password, and if I start KDE instead it also works OK. So it doesn't seem to be hardware failure.I see from googling that others have had similar problems, but most seem to have been on installation, and involved either VMWare or USB keyboards. I'm not using either of those.When it broke I was trying to build PyCairo into an alternative installation of Python2.5, don't know if this is relevant, if some key package got somehow corrupted.
View 1 Replies
View Related
Aug 29, 2010
im trying to mount my built in sdcard reader
View 1 Replies
View Related
May 5, 2010
after having tried out almost all suggestions found here and elsewhere on the internet, i'm somewhat at my wits end The situation: I'm running Kubuntu 32Bit Version (at the mom 10.4) on a HP-Compaq 6735s (AMD Processor, Vanilla 32Bit Install). My first Install was last year with 9.4 and the Broadcom 4322 wireless worked like a charm after installing the proprietary STA-driver under System -> Hardware Drivers. As the update didn't work out really without glitches, i did a fresh install and lost my wireless. I tried various combinations and tutorials but to no avail. My card is found, the driver installed, but i cannot access my access-point. I can SEE the access point (and all my neighbors'), but knetworkmanager does not seem to do anything. To be sure, I installed wicd (nice tool by the way). Trying a connect here told my my credentials were bad (incorrect passphrase for my WPA2 Personal auth), which is not true. I tried connecting without security, didn't get an IP. So it seems somehow the card is working, but all functions needed for passing information to the access-point are unavailable.
This is what I tried:
both broadcom-drivers
fw-cutter
installing the driver by hand
Installing the driver via Hardware Drivers produced the same results as any other, viz the card is working, but not connecting. Unfortunately knetworkmanagers error messages are a bit sparse, or rather non existant. My guess is that somehow the firmware is not properly loaded (or the wrong type??).
View 9 Replies
View Related
May 13, 2010
my 3G card Huawein E630 sucesfully on carmic 9.10. However, after upgrade to lucid 10.04, I cannot connect anymore.After insertion card contains drive containing windows drivers and modem.In karmic both were detected properly, however in lucid only drive is visible and modem is not detected.Connection is setup properly, but network manager does not offer me the connection.
View 3 Replies
View Related
Oct 9, 2010
I recently installed 10.04 and everything Just Worked.Before Lucid, I was using 9.04 and had successfully gotten my Broadcom 4306 working perfectly... which is why I think the Lucid install went so perfectly.Well, after a botched hiberation (Dell Inspiron 9100), my wireless is dead in the water.I've tried "ifdown", "iwconfig", "/etc/init.d/network restart" and "force-reload", 'modprobe -r b43'
View 1 Replies
View Related
Jun 8, 2010
Summary: a long-working config involving a 1st-generation Ipod Touch with v1 firmware, Ubuntu, and Amarok 1.4 stopped working when I upgraded to Lucid.
A few years ago I was given a 1st-generation Ipod Touch, running the original v1 firmware (I never upgraded to the v2 firmware because v2 wasn't jailbroken at the time). I took it to a friend's place to activate and jailbreak it with her Mac laptop (I didn't have a Mac or Windows machine to install Itunes on; have been Linux-only for many years). Once jailbroken, I was happily able to use it with Hardy, Amarok 1.4, and ipod-convenience (which supply ipod-touch-mount/ipod-touch-umount).
This continued through upgrades to Intrepid and Jaunty. I didn't care for Amarok 2 in Jaunty, so I installed Amarok 1.4 from the ppa someone else made available. I continued to use it through Jaunty and Karmic, without any problems.
Last week I upgraded to Lucid. Syncing Amarok 1.4 to the Ipod Touch no longer appears to work; the Ipod fails to recognize any music transferred onto it (standard "No Music - you can buy music at Itunes" error screen), so I presume this is a libgpod/hash error. I have the FirewireGuid properly set in the .../Device/SysInfo file, as I always have.
Every time I use the Amarok Ipod "connect" function (which runs ipod-touch-mount) it tells me no valid Itunes db was found, and asks to initialize the db. I can then transfer music to the Ipod, and successfully disconnect, but it's not recognized on the Ipod after a respring or reboot.
I've tried RhythmBox and gtkpod briefly with no luck either.
Relevant installed packages:
Code:
ii amarok14 2:1.4.10-0ubuntu3~ppa5 Amarok 1.4 series
ii amarok14-common 2:1.4.10-0ubuntu3~ppa5 architecture independent files for Amarok
[Code]....
Edit: a little more info: after I let Amarok initialize the Ipod Touch and transfer a song to it, the iTunes.db that gets created on the Ipod is 0 bytes long. I presume this is the source of the problem, and indicates something is going wrong with libgpod's creation/editing of the db.
what I should do from here? I've tried removing the DB by hand, but it makes no difference - the subsequent operation to initialize the db results in the same 0-byte file.
View 3 Replies
View Related
May 18, 2010
After upgrading to the latest Ubuntu, my wireless card stopped working. I keep on pressing the button but the little orange light wont come on...I have an aspire 5517 with "Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)" I have tried drpjkurian's tutorial for madwifi with no success . (http://ubuntuforums.org/showthread.php?t=1309072
View 2 Replies
View Related
Nov 10, 2010
I have two sound (or audio) hardware on my desktop computer. One is part of my computer motherboard and the other one is a sound card (CA0106 Soundblaster) I bought to replace the other one. When I first installed Ubuntu, my sound card was working properly after I made the necessary changes (system>preferences>sound), but after a few days it just stopped working and the sound from the motherboard is only working.
I reinstalled Ubuntu to my computer a few days ago, and my sound card was working again, but once again, it stopped working after a few days. How can I fix this?
View 2 Replies
View Related
Dec 16, 2009
Our smart card readers stopped working with Firefox and Thunderbird after upgrading from Fedora 9 to 12. When I first opened it, Thunderbird warned that the "CAC Reader (DoD Configuration Extension)" is incompatible with the current version (3.0b4) and disabled the extention. Firefox (3.5.5) just doesn't work. The module listed in Mozilla Firefox/Thunderbird [Security Devices] was "/usr/lib64/pkcs11/libcoolkeypk11.so" which is still there. To get it working in Fedora 9 I was able to run an installer from [URL]. That was before my VeriSign software certificate expired.
Now I can't even connect to forge.mil because they require a PKI cert to connect. I'm wondering how they expect someone to get a driver for their CAC reader if they need a working CAC reader to get the driver - seems like a "Catch 22" situation. I also still have the rpm's that I downloaded before from software.forge.mil. I tried installing those but that didn't help.
mozilla-dod-configuration-1.0.2-0.noarch.rpm
firefox-mozilla-dod-configuration-1.0.2-0.noarch.rpm
thunderbird-mozilla-dod-configuration-1.0.2-0.noarch.rpm
Does anyone know if there is a later version of these RPM's or if there's another way to get our CAC readers working again with Firefox and Thunderbird?
Relevant Background Info:
Installed Packages:
ccid-1.3.9-2.fc12.x86_64
coolkey-1.1.0-11.fc12.x86_64
mozilla-dod-configuration-1.0.2-0.noarch
firefox-mozilla-dod-configuration-1.0.2-0.noarch
thunderbird-mozilla-dod-configuration-1.0.2-0.noarch
Could a renamed kernel module be part of the problem? What do you make of the following information?
Find library dependencies:
Code:
[root@inet3 ~]# ldd /usr/lib64/pcsc/drivers/ifd-ccid.bundle/Contents/Linux/libccid.so
linux-vdso.so.1 => (0x00007fff41bff000)
libusb-0.1.so.4 => /usr/lib64/libusb-0.1.so.4 (0x00007f52a37fd000)
libpthread.so.0 => /lib64/libpthread.so.0 (0x00007f52a35e1000)
libc.so.6 => /lib64/libc.so.6 (0x00007f52a3268000)
/lib64/ld-linux-x86-64.so.2 (0x000000374b400000)
[root@inet3 ~]# locate linux-vdso.so
[root@inet3 ~]# locate vdso.so
/lib/modules/2.6.31.6-166.fc12.x86_64/vdso/vdso.so
[root@inet3 ~]#
##!!
There is no module named "linux-vdso.so". It looks like there was a name change that broke the libccid.so dependencies. I tried creating links within "/lib/modules/2.6.31.6-166.fc12.x86_64/" named linux-vdso.so pointing to vdso.so but it still isn't working. I've unloaded the module within Firefox (and Thunderbird) preferences within the [Security Devices] manager. Then tried adding it back using the [Load] button and specifying the coolkey library again but it's still not working.
View 12 Replies
View Related
Jul 14, 2011
the distro is slackware64-13.37 I did install the firmware it was working I have no Idea why it quit wicd sometimes looks like it's connected only to have mozila not find a network connection most of the time wicd times out when obtaining ip address the router is working just fine and was reset to out of the box factory defaults and is working with windoze vi-stool from dmesg I get
[code]....
View 1 Replies
View Related
Jun 11, 2010
I have an HP 2133 Mini-Note [KX869AT] with a Broadcom 4312 wireless card. I've had Ubuntu 10.04 on my machine for a few weeks now and everything was great until my wireless card abruptly stopped working. It doesn't detect any wireless networks,uch less connect to them. I tried reinstalling the proprietary driver, but that hasn't worked.
View 1 Replies
View Related
May 11, 2011
Well, I have an issue with my wireless card in Ubuntu 10.04, my wireless card model is:
the D-Link WIRELESS N 150 DESKTOP ADAPTER DWA-525. I was already successful getting it to work by using the RaLink driver suggested here and following the instructions in their readme.But after a system update I performed through Update Manager (in which I guess the kernel was updated), the device stopped working completely. The wireless icon remains(in the top panel), but it displays a red exclamation mark next to it
View 9 Replies
View Related
Nov 3, 2010
Anybody know how to get pictures off of one? I've got a computer with XP, but the software doesn't want to work. I've tried setting it up in a VM, but VirtualBox won't patch the camera through for some reason. The SD card adapter it came with stopped working, so that's a no-go.
View 2 Replies
View Related
Jan 9, 2010
I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.
After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.
Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.
Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:
yum info kmod-wl-PaE
Loaded plugins: presto, refresh-packagekit
Available Packages
Name : kmod-wl-PAE
Arch : i686
[Code].....
One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?
View 14 Replies
View Related
Jun 20, 2009
HH 8.04 on a Toshiba Satellite A75-S2762. Rather suddenly, I have no sound. On startup, I click on the volume control (speaker-with-x) icon in the tray, and the error message in the attachment shows up. (That message only appears once per session, subsequent clicks just say "No volume control GStreamer plugins and/or devices found.") Synaptic shows a broad range of said plugins installed (everything from Pidgin to good/bad/ugly), I mark them all for reinstallation, but nothing. I have no sound from any program, and whenI go to Control Center | Sound, there are no options down in the "Device" pull-down.Recenthanges to system: installed and later uninstalled VLC for i386, however sound continued to work for at least one or two sessions. (However, after installing VLC, I got no sound in Totem or VLC, only in Dragon.) No other changes of note
View 1 Replies
View Related
Jan 30, 2010
After doing a reconfigure of my wrt54gl router, trying to activate WEP encryption, and then finding WICD wouldn't connect, and returning to the original config on the router, now wicd won't reconnect the wireless card. Here's the wicd.log entry from the attempt to connect:
Code:
2010/01/30 18:40:46 :: ifconfig wlan0 up
2010/01/30 18:40:46 :: iwlist wlan0 scan
2010/01/30 18:40:47 :: ifconfig eth0
2010/01/30 18:40:47 ::
2010/01/30 18:40:47 :: {}
2010/01/30 18:40:47 :: hidden
2010/01/30 18:40:48 :: scanning done
2010/01/30 18:40:48 :: found 4 networks:
2010/01/30 18:40:48 :: found use_settings_globally in configuration 1
2010/01/30 18:40:48 :: found afterscript in configuration None .....
View 3 Replies
View Related
Sep 9, 2010
I'm using Ubuntu 9.10 on a Lenovo ThinkPad T61 using an Intel PRO/Wireless 3945ABG. My laptop's ability to connect to a wireless network stopped last night, and I'm not sure why. It's definitely something on my end, as my roommate can connect to the internet on a Windows box. I can wire in without a problem, but that's a pain and my Ethernet cable got lost in the shuffle when I moved back to school. I've been able to get into this network before and nothing about it has changed. I've been able to hibernate and restart and such and nothing has ever needed to be reset.
The router's a D-Link WBR-2310. Wicd and Network Manager see the network (I'm back to using wicd) , but wicd appears to get stuck at "Obtaining IP address..." and says "Unable to connect: Cannot obtain IP address". I know my password is correct (I set up the router and I'm the CS undergrad in the apartment so I manage it), lspci sees the wireless card, ifconfig and iwconfig return information about the interface, dmesg|grep wlan0 doesn't seem to have anything terribly out of the ordinary, but here's that output:
Code:
allyanncah@taliesin:~% dmesg | grep wlan0
[ 23.514202] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.609016] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.756143] wlan0: direct probe to AP 00:24:01:cb:4e:7e (try 1)
[ 38.758791] wlan0: direct probe responded
[ 38.758796] wlan0: authenticate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.760587] wlan0: authenticated
[ 38.760609] wlan0: associate with AP 00:24:01:cb:4e:7e (try 1)
[ 38.763318] wlan0: RX AssocResp from 00:24:01:cb:4e:7e (capab=0x431 status=0 aid=1)
[ 38.763322] wlan0: associated
[ 38.765502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready .....
I've tried:
- reinstalling wicd
- uninstalling wicd and installing network-manager
- restarting
- shutting down and booting back up
- restarting the router
- sudo /etc/init.d/networking restart
- taking the interface down and back up with ifconfig
I haven't changed anything recently in regards to my wireless card, and all the fixes I've tried are things I've done before without an issue. The only thing I'm wondering about is if doing a hard reset might have broken something (I know this is a cardinal sin, but there's a whole 'nother problem I haven't been able to fix with the OS hanging every once in a while over a VPN daemon when it tries to shut down or restart -- I've left it for hours to see if it actually gets anywhere and no luck, won't do a soft reset). I'm nervous about reinstalling the driver just because I've never had to do it and drivers are a finicky business. I imagine there's a config error somewhere?
View 2 Replies
View Related
Feb 23, 2011
I have a new Thinkpad t510 laptop with an intel centrino wireless N card (no bluetooth). I installed ubuntu a couple weeks ago after I got another hard drive in the expansion bay. I have the drive partitioned into two sections, 250gb for file storage, and 250gb for the linux OS. Currently no other OS is installed on the other harddrive.
I have had everything perfect for the past couple weeks, but once i installed some updates today, my wireless fails to work now. Just some general info that you might ask me, lspci | grep Network, returns
00:19.0 Ethernet controller: Intel Corporation 82577LM Gigabit Network Connection (rev 06) 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 Furthermore, on the top right of my screen, my wireless is grey'd out and says no network devices available on hover.
[Code]...
Im trying to connect to my college wireless network. I have looked a thinkwiki and no one has posted any bugs. Any ideas on getting it working again?
View 1 Replies
View Related
Feb 13, 2010
fsck died with exit statusAn automatic file system check of the root file system failed. A manual fsck must be performed then the system restarted. The fsck should be performed in maintenance mode with the root file system mounted in read only mode..This is the message I now get with the word "warning" in red
View 2 Replies
View Related
