As both root and myself, I've gone into the:
configure desktop -> display and monitor
thing and set "primary output" to "DVI-I-1" and
set the DVI-I-2 connection to the "Right of DVI-I-1" position
[code]....
Doesn't work when done either as root or as me. So, there *must* be a way. How?
I'm running a lenovo laptop with an nVidia Quadro FX 570M and Ubuntu 9.10.
I cannot get my external monitor to work properly for me (using nvidia-settings). It basically creates a single continuous monitor space across both the external and the inbuilt monitor (maximising a window, covers BOTH monitors and the gnomepanels run across both monitors)
I think its related to my xorg.conf settings, which are as following, Can any one help:
(It used to work for me when I was using ubuntu 8.4)
Anyone have a multi-card, multidisplay setup working with gnome 3 and Fedora 15? I have two nvidia 9500GT cards driving 4 monitors (2 per card) using the proprietary nvidia drivers (270.41.19) The setup had been working fine with the previous version of Gnome and Fedora 14. I was using xinerama to have one large desktop spanning 4 screens. No problems until I upgraded. KDE works after configuring using nvidia-settings, however gnome 3 is not useable. I get two screens black (but with mouse pointers when I move the mouse) and the right two screens with the background but the activities corner in the right hand side of the right most screen, rendering it useless.
View 10 Replies View RelatedI've always used Debian with a single monitor and no need of proprietary drivers, because I usually don't do graphics or multimedia. Now I'm asked to set-up a machine with 3 nvidia video cards (770) and 4 monitors and everything went south. I started with just 2 monitors connected to 2 different video cards, not wanting to push my luck.
I installed a fresh Jessie and followed the instruction to install the nvidia drivers and tools from the Wiki. Everything went smooth. After reboot I executed (as root) nvidia-settings and I configured the two monitors to be one to the right to the other, with BaseMosaic option (at this point just one monitor was active) I saved the configuration to /etc/X11/xorg.conf , I even executed nvidia-xconfig as suggested, I rebooted and nothing happened, only one monitor was working, while the other -- looking again in the nvidia settings -- was still disabled.
I then tried with xinerama option and things are even worse, since now both monitors are black. I can login in one textual shell, but then I don't know what to do, since in my 10+ years of linux ... I never had to mess with X server. Is there a way to at least recover a working X without reinstalling everything?
I'm using a NVIDIA 9600M GT on my laptop running Ubuntu 10.10. The laptop has a 16:10 display, I also connected my 16:9 LCD TV via HDMI. I would like to use them as clones. The problem is, as my TV has a different aspect ratio than my laptop display, the image does not fully fit on the TV. For example, when using a resolution of 1280x800 (16:10), one tenth of the width of that image is missing on my TV, as it has an aspect ratio of 16:9.
In Windows, the NVIDIA software stretches the image so that it appears a little distorted on my TV, but at least I see everything. Is it possible to do that in Ubuntu?
I would like to create the following setup:
3 monitors: 1 2 3
monitor 1 and 3: 4:3 monitors, running 1600x1200, rotated 90 degrees
monitor 2: 16:9 monitor, running 1920x1080
Can this be done in Linux? If so: how? If not: what's preventing it from being possible?
I have been trying to configure dual monitors of different resolutions on 11.4 the Nvidia configuration utility does not know where or what to save anything anymore and goes wonky. Trying to use it is a dead end for me. X11 is a mess. What happened to SAX and things like this that were part of openSUSE and just worked? Supposedly we X11 got better. I think it's got over complicated and much worse. This stuff just worked in 11.1 and KDE 3.
View 9 Replies View RelatedI've a laptop with 2 external monitors connected to it.Using SaX2 I can't configure it in a way where it only uses the two external monitors and not the laptops own screen.With nvidia-settings I can configure it properly, as I am however unable to save it due to a missing xorg.conf file how am I supposed to save the this config so it isn't 'forgotten' between reboots?
View 2 Replies View RelatedOn openSUSE 11.1 I was able to configure KDE 4 for 2 monitors with sax2 (although the resolution was bad).On 11.2 neither SAX2 nor KRandR seem to work. The KDE User Guide says that a driver supporting version 1.2 is necessary. However the nvidia driver for eForce FX Go5200 seems to support only version 1.1.Is there a way to use both monitors with SUSE 11.2? I am quite desperate since for my work using only 1 monitor is definitely a handicap.
View 5 Replies View RelatedAnyone using dual monitors (dual head) and has a nvidia graphic card, might be interested in the app, Disper, nvnews.
You can configure a dual monitor, on/off, via nvidia-settings, but you can automate it with Disper by writing a script to execute something like:
I have openSUSE 11.4 with standard KDE and two screens attached.Here's the question: How do I configure dual monitors when using the proprietary nVidia drivers?The openSUSE 11.4 installation put in the "nouveau" drivers for my nVidia card and I was able to configure dual monitors using KDE's Configure Desktop --> Display & Monitors GUI configurator. I could also set up dual monitors using a script based on xrandr (e.g. "xrandr --output VGA-1 --auto --pos 0x0 --output DVI-I-1 --auto --pos 1920x0")My screens are detected as VGA-1 and DVI-I-1 by the nouveau drivers.
OK, today I switched to the proprietary nVidia drivers. Only one of the screens is now detected and displayed in the KDE monitor configurator and that's marked as "default" rather than as a VGA or DVI connection.When I run xrandr to configure monitors, I get error messages if I refer to VGA or DVI hardware.
More info -- RPMs
nvidia-gfxG02-kmp-desktop-260.19.36_k2.6.37.1_1.2-23.1.x86_64
x11-video-nvidiaG02-260.19.36-24.1.x86_64
[code]....
I'm starting to have A LOT of opened windows in my machine. Sometimes within a project, I have e-mail/task management/personal e-mail/twitter, and a lot of different opened applications/terminals in my Linux workstation.Sometimes it would be interesting to have different workspaces to projects instead of this configuration I have nowadays that are classes of work (bad name, I know, but I think you got the idea).I'm starting to think about using two monitors: one with Corporate Management, Work and Personal. The second monitor is only the development state: each workspace here is about a project being worked on instead of groups of works like before. A workspace may be implementing different classes for example.
My question is: I just want to change to a second monitor using the mouse. I want to still be able to change workspaces in the same monitor using keyboard shortcuts. The keyboard shortcuts wouldn't change monitors, just worskpaces on the same monitor. All the tutorials I read (like this one) only tells how to use multiple monitors but doesn't answer my question about keyboard shortcuts.Does Linux (Ubuntu 10.04 Lucid Lynx or Debian 5.0.5 Lenny) support this envisioned setup (Different workspaces in a way that keyboard workspace switching only works in the current monitor) ? If so, how?I haven't tested this setup, that's why I'm asking. In this question the user says it works exactly how I want it to behave, can someone else confirm it?
So essentially, I have 3 monitors and i'm attempting to run 2 different window managers/sessions at once split up on the monitors. It is intended to be like this:
Code:
[GNOME/Compiz - Screen0]
- Left Monitor[code]......
I am hoping I have a simple one to solve here! I've been looking around online, trying to find out how to configure multiple desktops to have their own taskbar.Most of my results suggest that I should be able to click on the menu, choose favorites, and go to Configure Desktop. In the new window, I should see a taskbar section on the left hand side?I am running OpenSUSE 11.2 on two machines and neither of them have this option. I just wanted to see if somebody knows where I can find the window to configure separate taskbars for each desktop?
View 1 Replies View RelatedI have installed openSUSE with Gnome3.
I had to install the nVidia proprietary drives so the OS would boot into Gnome3 and not fail safe mode. Without the proprietary drivers installed the display settings said:
Driver: software rasterizer in use
After installing the nVidia drivers Gnome3 works in one monitor, but I would like to be able to use my other two monitors (totaling three with two video cards.)
When I run nvidia-settings to generate an xorg.conf file it hangs, so I used nvidia-xorgconf to generate the xorg file and then used nvidia-settings to configure my extra screens.
This fails with a permissions error, running sudo nvidia-settings fails with the following error:
ERROR:
So, I ran nvidia-settings, saved the settings file to my /home/$USER dir, then copied xorg.conf to /etc/X11/
Logging out and logging back into Gnome fails with the error:
This problem extends to Ubuntu running Gnome3, so my thinking is:
a) Imma id10t and something in my xorg.conf file is wrong,
b) there is an issue with Gnome3/nVidia/Multiple displays.
I would really like to use Gnome3, it works on multiple other machines (ironically all ATI devices) just not the machine I use all day long...
Here is my xorg.conf file as generated by nvidia-settings.
Code:
I am trying to configure Fedora 11 to run on two monitors. However, after hooking the second monitor up, I can not extend the display to it. Hell, in the display options, it doesn't even show that a second monitor is connected. Restarting X does not help either.
View 2 Replies View RelatedWHY I can't enable my 3rd and 4th monitor on Ubuntu 10.04? Does it have anything to do with xorg? I can easily do it in Windows! In ubuntu ATI control center will recognize the 3rd monitor but DO NOT let me enable it... the same about the video card! I tried to do it manually changing xorg.conf but it totally ignores it! I found this thread: [URL]Does it have anything to do with XRandR? I managed to get the Crossfire working and enable it after put two identical cards. I've tried adding a 3rd card to even try a 4th monitor but it will not let me at ALL... WHY THIS?? I can do it in Windows but I do not want to use Windows! Why do not allow to use more than 2 monitors??? I'm running a clean new installation of Ubuntu 10.04 64bit and I've installed the ubuntu drivers for my video card. I've a double ATI HD 5770 (crossfire) and a third video card in the motherboard (Asus M4A89GTD Pro/USB3).have 4 monitors, 3 in the crossfire and one in the motherboard. I've managed to do it in windows but in linux I can get max of two monitors working...
View 1 Replies View RelatedI use Kubuntu 10.04. I want to use multiple monitors in an extended way. When i connect a monitor to my laptop, i get the same desktop view on both monitors. When i go to system settings - display - multiple monitors, i see the message: "This module is only for configuring systems with a single desktop spread across multiple monitors. You do not appear to have this configuration".
View 9 Replies View RelatedI'm trying to get dual monitor support enabled in Suse 11.3 Previously I had this in Suse 11.2 using a dedicated NVIDIA graphics card with VGA and DVI output and this was done in a GUI. I now have 11.3 and a built in ATI card with VGA and DVI output When I run xrandr I get the following Code: Screen 0: minimum 320 x 200, current 1440 x 900, maximum 8192 x 8192 VGA-0 connected 1440x900+0+0 (normal left inverted right x axis y axis) 408mm x 255mm
1440x900 59.9*+ 75.0
1280x1024 75.0 60.0
1280x960 60.0
1152x864 75.0
[code]....
I tried using xrandr --screen 1 but it says Code: Invalid screen number 1 (display has 1) I'm looking to expand the desktop onto the second screen so I can photo edit on one screen and web browse and instant message in the other screen Currently using the Radeon R600 classic driver from ATI
I have Ubuntu 10.04 running gnome and two monitors. I am wondering if a can get a better multi-monitor configuration tool. The one I have, gnome-display-properties, has too many problems, including: When I swapped my monitors over, the narrower (external) one now on the left. There is a width calculation error, such that I have a virtual monitor the width of the wide-monitor on the narrow-monitor and part of the wide monitor. And a virtual narrow-monitor on the remainder of the wide-monitor. Also the visible mouse pointer does is not aligned with the active spot, an x offset of one monitor width. I would like, in approximate order of importance:
[Code]...
I'm running Ubuntu 10.10 x64 as a guest in VirtualBox on top of Windows 7. I recently bought a second monitor, and I want to set up my Ubuntu guest to use both monitors. I configured VirtualBox to give two displays to the VM, and two windows are displayed when I run the VM, however, the Ubuntu guest only uses the primary screen and does nothing with the second--the second screen is just black.
When I go to the monitor settings, only the one monitor is detected (as an "unknown monitor") I have the latest guest additions installed and the driver under System-Administration->Additional Drivers is shown as installed and working correctly. I don't have any issues with the single display--it shows in the correct resolution, and works fine if I set it to fullscreen or seamless mode. Any thoughts on getting Ubuntu to detect the other screen?
I've been using linux for roughly 12 years now but I've always avoided linux on the desktop since touching X back in the day was quite a hassle. I recently decided that rather than keeping my windows desktop full of 15 PuTTY instances, I should rock the *nix desktop.
I started by installing Ubuntu 10.10 Desktop. It detected my two monitors handing off a pci express card just fine. I decided to install the ATI drivers when it prompted me - the proprietary drivers would let me select to use the monitors separately, but would always just default back to mirroring the screens. I was unable to get it to stop that, so I had to go back to the open source drivers. Which is fine, I don't really need the 3d accel. Roll forward a week, I ordered another video card to add another screen. I purchased another ATI card, since word on the street is that same-vendor chipsets play best together. This one had to be PCI, if this matters.
dmesg reports the new card is fine and happy, but the Monitors GUI thing doesn't detect any monitors off the new card, or report anything about it. So: what should I do to make the second video card get noticed?[URL]...
I have Ubuntu 10.04 running gnome and two monitors.I am wondering if a can get a better multi-monitor configuration tool. The one I have, gnome-display-properties, has too many problems, including: When I swapped my monitors over, the narrower (external) one now on the left. There is a width calculation error, such that I have a virtual monitor the width of the wide-monitor on the narrow-monitor and part of the wide monitor. And a virtual narrow-monitor on the remainder of the wide-monitor. Also the visible mouse pointer does is not aligned with the active spot, an x offset of one monitor width. in approximate order of importance:to be able to select which is primary monitor.to have multiple configurations. configurations to be automatically selected based on which monitors are attached.configurations to be cycled (reliably) when display mode key is pressed. when a display is deactivated, for windows to migrate to remaining monitors. option to not change display resolution when mirroring, but to use side/top blanking bars to pad out screen.
View 3 Replies View RelatedGot Ubuntu installed with not much trouble, tho I found the install CD not as helpful as it might be. Anyway, I have three monitors and want to get them running, same as in XP. Is there somewhere I can read up on this? At the moment my worst card is on the lowest PCI slot, and as I understand it, that makes it always the default, but XP has no trouble with that. Ubuntu's monitor setup page tells me 'unknown monitor' and seems unhappy with the graphics abilities of the card, but lspci reports all three cards correctly, so they are 'visible' at least.
View 8 Replies View RelatedI just abandoned Windows 7 for Ubuntu. I am trying to setup my monitors on my desktop. I have 3 monitors (i have 2 graphics cards with 2 monitors per graphics card -- so potential for 4 monitors).
Currently I have 2 of the monitors working, but they only mirror each other. I tried going in to System-Preferences-Monitors to configure them the way I want to, but nothing i do stops them from mirroring each other.
I'm trying to set up my monitor and tv for dual display but I'm having some problems. I want them to display the same thing so I've enabled twinview and I figured the second display position should be set as clone but when I save xorg and restart the x server the position reverts to absolute. Anyway, the monitor is set as the primary display and it's the one I'm having problems with. The tv is fine but the monitor's display is stretched off the screen so I can't see the far right or bottom of the screen. I'm very new to linux and I'm just finding my feet so if there's any other info needed you'll probably have to be very specific.
View 2 Replies View RelatedI have been playing around a bit today and decided to hook my tv up to my slack box. I have an NVIDIA gt220 using the proprietary drivers which supports multiple monitors and I can get various setups like an extended desktop and xinerama, but what I can not seem to do, and what I'd actually like to do, is just have both the monitor and the TV display the same images. If it would work better/easier I also have a second NVIDIA card, although it is a different model. I haven't bothered trying that yet as it seems like it would be easier to configure one card instead of two.
View 10 Replies View RelatedI was just wondering if is an easy way to configure three monitors run across two video cards (Nvidia Leadtek GTS250 PCI-E 2.0 1G 2DVI ) 2 on one, 1 on the other under the one xserver? I tried to get it going using the Nvidia driver package with no luck - 2 monitors seemed to be simple to configure using Twinview setting on a single xserver (my current settings) and I was hoping their may be a simple extension for three and if so is there an easy way to go about this? (I am new to Ubuntu).
[Code]...
When trying to install the nvidia graphics driver I get the following error-message:
ERROR: The kernel header file '/usr/src/linux/include/linux/version.h' does not exist. The most likely reason for this is that the kernel source files in '/usr/src/linux' have not been configured. How do I configure the kernel source files?
How to get AWN to run on two monitors? I want a bar on each monitor. I used to be able to start two instances using a shell script below but that doesn't seem to be working now.
Code:
#!/bin/bash
killall avant-window-navigator
sleep 4
DISPLAY=:0.0 avant-window-navigator &
sleep 4
DISPLAY=:0.1 avant-window-navigator &
Playing around more with this and it looks like avant no checks to see if there is another instance running and will not start if there is. That is a bummer. Any way to change this?
dccrens@cavermax-ubuntu:~$ DISPLAY=:0.0 avant-window-navigator &
[1] 15569
dccrens@cavermax-ubuntu:~$
** (avant-window-navigator:15569): WARNING **: Another instance of Awn is running
[1]+ Done DISPLAY=:0.0 avant-window-navigator