I have an HP OfficeJet 6500 wireless all in one.I've tried using the HPLIP that comes in the distro, uninstalling that and installing the scripted installer from the site, and manually installing the RPM.Yast isn't detecting my printer, whether I try a USB install or over the network.I have all the dependencies, CUPS is up to date, and this printer is detected by Fedora and Kubuntu.
View 9 RepliesDeskjet-F4400-series
--------------------
Type: Unknown
Installed in HPLIP?: No, not using the hp: or hpfax: CUPS backend.
Device URI: usb://HP/Deskjet%20F4400%20series?serial=CN9C1CK70705C5
PPD: /etc/cups/ppd/Deskjet-F4400-series.ppd
[code]....
how do I get the printer installed in hplip? I can print but cannot scan. xsane will not recognize printer. Jaunty 64bit 2GB Ram 350GB HD
I've followed the instructions that I can find as well as I can, but it seems I've hit a relatively unusual condition. Here's the preliminary stuff:
lspci output:
Code:
0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 05)
Subsystem: Apple Computer Inc. Device 008c
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at 97300000 (64-bit, non-prefetchable) [size=16K]
[code]....
Currently, the interface seems to be set up correctly in the YaST network settings thing, labeled as wlan0, and it doesn't have the 'Not Connected' indicator after it.
EDIT: iwconfig doesn't list wlan0; it just lists eth0 and lo0, saying neither have a wireless extension
Tofirst automatic software update was launched on my newly installed openSUSE 11.2 - and apparently it replaced Firefox 3.6.4 with 3.5.9.I tried to find out how to install 3.6.4 using YaST2, but adding the following repository didn't help me any further:Index of /repositories/mozilla/openSUSE_11.2What do I need to do to have YaST2 install the latest firefox version?
View 8 Replies View RelatedI am using Fedora 12. I have the following problem, when i working with system-config-samba dialog:I add the new user on the server:as following:
Unix username: vova
Windows username:test
As described in Customisation Guide for Red Hat 9: "If the user has a different username on a Windows machine and will be logging into the Samba serverfrom the Windows machine, specify that Windows username in the Windows Username field."So i logged from the Windows machine not under test(Windows username) but under vova.And i logged in without the problem. However it seems that samba should check windows username=test (as have written in samba-config) and ask an password for different users. And additionally, if samba check the currect user in Windows itself and verify it with Unix user, what for we need write the Windows username in samba config? I don't understand
The new 2.6.35.7 kernel fails to boot on my Lenovo laptop. I had previously compiled a 2.6.35 kernel with a couple of different .config files and never had it boot properly. The failure occurs very quickly and I am including the final screenshot in case that helps.
View 7 Replies View RelatedI recently acquired a Gateway with a Radeon video adapter in it.I've tried both the proprietary and open drivers.I've followed the installation instructions here: https:[url]........to no avail. I know that my video adapter is compatible with Ubuntu, because I have seen the explode/fade effect on launcher buttons -- until I reboot.I have even seen all of the screensavers working properly, again, until I reboot.Is there a config file not being set up properly?Additionally, this is what Gateway says about the video adapter:
"ATI Radeon� HD 3200 Graphics with up to 1919MB of HyperMemory� supporting Shader Model 4.0 and Microsoft� DirectX� 10 with AMD RS780MN Chipset"It uses shared memory.
I've set up hplip and added a "fax" device. However, when I go into open office and try to fax something, it says it's doing it, then pops up a window saying "step 3 of 5" asking me to add files to the fax (there are no others to add) and only the "cancel" button is clickable. Then in HP Device Manager, it shows the fax as having a job but it never does anything.
View 6 Replies View RelatedI have following setup on my one of the customer where we had suplly thin client. Customer have their old system with SuSE Linux Enterprise Desktop 10.2 with HP LaserJet P1008. They had configure this printer thru foo2xqx & HPLIP 2.8.10. Our Thin Client which we had supplied with SuSE Linux Enterprise Desktop 11.1 & HPLIP 3.10.2.
I am able to install HP printer on my thinclient but thru IPP but, when we fire any print command I am getting "Stopped: /usr/lib/cups/filter/foomatic-rip-hplip failed" error. If I can connect printer on thinclient I am able to print. But, thru IPP share I am not able to print. Also, customer have their old thinclient also on which they share this printer so, I am not able to detach this printer from that system.
Everytime I get HPLip working with my printer, it will only work until I shutdown the computer. On next restart, it no longer works and the only way to get it to work again is to delete the printer configs in hplip and re-create them!
View 2 Replies View RelatedTrouble with cups - Opensuse 11.3 x86-64
Hplip installed
prrinter = HP photosmart 4280
No way I can set the printer as default printer in cups as in 11.2. Now hp-device-manager. Part of hplip is complaining "set the default printer"
When I try to change some settings of my printer using HPLIP it tells me to add myself to the lp an sys group. Is that safe ? What are those groups used for ?
View 9 Replies View RelatedI recently bought the HP Officejet 8500 all-in-one. I was at that moment using OpneSUSE 11.1 on a HP Pavilion laptop. As this printer was too recent for the version of hplip in the 11.1 repositories, I downloaded the source, compiled and installed it. Last week I upgraded to 11.3, and now the repositories have an even more recent version than what I installed. But in Yast the hplip package is marked as 'never install'. Why is this and how do I remove this blocking? How can I install a hplip package compatible with 11.3?
View 2 Replies View RelatedIf anyone else is having problems with their HP Photosmart (c4580) multifunction after the latest updates, here's what I did to get mine working once again -
1. Uninstalled hplip (ALL versions including standard AND packman), this also automatically uninstalls hplip-hpcups (which seems to be the cause of the problems) and automatically re-instates hplip-hpijs instead.
2. Remove all installed printers in Yast and also check on http://localhost:631 to make sure they are all removed.
3. If you have (as I did) lots of annoying test pages spooled and waiting to be printed, reboot now to (hopefully) get rid of them.
4. Disable your firewall (through yast) and add allowed service - cups. You might want to restart it, but to save time/frustrations/headaches/smashing your computer and printer out of frustration I would leave it disabled until you have successfully achieved a test page printout!
5. Download hplip-3.9.6b.run from here - HP Linux Imaging and Printing and follow the install instructions. It should eventually bring up the GUI interface where you can detect your printer.
5a. If it doesn't find your printer in the scan, then you are most likely going to have problems. Make sure your firewall is disabled/allowed and that the printer is actually reachable (ie by ping or the web interface). If still not reachable, then you need to find out your printer's IP address and enter that in a browser and get it's hostname.....
I have this HP Laser Jet P1005 and it working wonderful in 11.1 whit HPLIP .But now i switch on printer before installing 11.2 (lake every time before installing) and lucks like everything is OK,printer was recognized but not printing(Devise communication error5012) hеre is a log of - "hp-check -t"
Code: HP Linux Imaging and Printing System (ver. 3.9.8) Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP This software comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to distribute it under certain conditions. See COPYING file for more details.
[Code]....
I got cartridge is low warning and after a couple of days refilled the the black cartridge (#56) for my HP officejet all-in-one printer. The low warning is still there and when I try to print, it does not even try/use the black cartridge. I believe it is tracking the serial number of the cartridge (showing in the status of hplip manager). I know the cartridge has ink, because I am able to scan/copy on the all-in-one and it does use the black. I have tried to clean, align, and test using the hplip tools, but it has not worked. Any ideas on how to erase the memory or have it retest the cartridge for ink ?
View 7 Replies View RelatedI have downloaded the hplip command on the desktop, attempted to cd desktop, and it shows "no such directory". running this command so I can set up my printer? And I can't seem to put the screenshot here..
View 9 Replies View Relatedafter an update to 11.2 (from 11.1), 64 bit, I don't get the printer to work. I reinstalled the driver and checked in cups: it says that the printer is available and waiting for a job. When I send something to the printer, nothing happens. The priont job will be stopped immediately. The printer is properly connected: xsane finds the scanner, that is part of the printer, without a problem. The printer is also ok: I can copy documents, it just works fine.
[Code]...
I just installed opensuse 11.3 and was configuring the printer (via http) as usually using the HP Device Manager. But this time I got these error message:Printer queue setup failed. Please restart CUPS and try again
These lines were generated in the error-log of cups:
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"!
E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Skipping "/usr/share/ppd": loop detected!
[code]....
I have newly installed opensuse 11.4 x85_68 on my computer. Yast2 refuses to see my connected HP Laserjet 4l on parallel port, I can install a second network printer but neither hplip nor yast2 can start printer configuration. The printer is present in Yast2 hardware List under /dev/lp1
View 8 Replies View RelatedI have the following set up in my crontab:
Code:
# crontab -l
# m h dom mon dow command
*/5 * * * * /usr/bin/perl /usr/local/bin/perl/managed_arp_data.pl >> /var/log/arpdb.log
*/5 * * * * /usr/bin/perl /usr/local/bin/perl/infoblox_fixed_sync.pl >> /var/log/crossref.log
00 23 * * * /usr/bin/perl /usr/local/bin/perl/infoblox_host_sync.pl >> /var/log/host_sync.log
0 * * * * /usr/bin/perl /usr/local/bin/perl/infoblox_excl_sync.pl >> /var/log/excl_sync.log
None of these jobs is apparently running, however they did run on the 31st (yesterday), but not on the 30th or any other day during the last 10 days that I have logs for. I think I've set cron to run at log level 1, but I don't know where that log goes, I don't see anything like /var/log/cron
So, couple questions:
* If I do something like "sudo -s" to get a root prompt and then do a "crontab -e", which user does that crontab get executed as?
* Where should I look for cron logs?
* Anyone know why a job would run on the 31st, but not any other day?
I have an issue with cfservd, from the cfengine package not listening on both ipv4 and ipv6. Tracing through the source indicated that the issue was with the getaddrinfo() call. I have used the example code on the man page and can confirm that it doesn't work as expected on either Fedora 12, Fedora 10 or CentOS 5.3
The servers I am testing on have both ipv4 and ipv6 enabled and working. i.e. I can ssh to them using either -4 or -6 and netstat -a shows 0.0.0.0:22 and :::22
Running the example code on the Fedora servers results in only a single IPv4 address structure being returned by the getaddrinfo call and hence only listening on the one protocol. Strangely, on the CentOS server only the IPv6 address structure is returned.
I need both IPv4 and IPv6 for cfengine but am at a complete loss as to how to get it to work when the issue appears to be something fundamentally wrong at the OS level.
I have done some searching around and now know that the 64 bit version of Wine is useless. I tried to install the 32 bit version and apparently succeeded. The problem is that when I open Wine File the .wine-x86_64 folder reappears. I don't even know where the 32 bit folder is.
I have tried
Code:
yum erase *wine*
but it does not seem to work. However this does.
[Code]...
I have just installed the new version 10.04 of xubuntu but I cannot enable xdmcp.
1) the gdm.conf (usualy in /etc/gdm/) is missing (where is now this file?);
2) the custom.conf apparently don't work;
3) the remote tab in login windows are missing
I'm using Slackware 13.1 on a new laptop (MSI 1481). Everything has worked great except when I put a DVD in the drive (like the Slackware DVD) the drive spools up and down constantly - you know, how it goes from slow speed to fast speed. I figured it was hal polling it every 2 seconds and that for some reason it was causing it to actually kick in and read the DVD, but disabling that didn't help. I've also tried not starting X or xfce (going to runlevel 3) but that didn't make any difference - as soon as I put the dvd in, it starts up.
It's not just the Slackware dvd either, it's any DVD. Movie DVDs however don't seem to spool up to higher speeds but you can still hear the drive running constantly, so there is some different. I'm not mounting the drive or anything, just close the tray and listen to the rhythmic annoyance of the drive at full speed, then not, then full speed, then not.
I don't see any other suspect processes with top or ps either. Anyone have any idea why this would be if it's not the polling doing it? I'm starting to think a kernel or hardware thing. The drive I have is reported by cdrecord -scanbus as "Optiarc DVD RW AD-7580S FX20".
I'm at a loss. I'm thinking next I'll have to install another distro to at least rule that out, but with so many variables (packages installed, kernel version, driver versions) I don't know that this approach would tell me much.
I have a user that is reporting the following error on a bounced message:
Quote:
smtp;554 5.6.1 Body type not supported by Remote Host
He is forwarding emails from his exchange server to a recipient in Germany relaying through our smtp server using Surgemail as the MTA.
He called a senior tech specialist at Microsoft to get help thinking the problem was on his end (exchange server). According to this "specialist", he said the problem was that our smtp server was not advertising 8BitMIME in its 250 statement. I tested this myself by log in on to the smtp server and doing typing the following:
Code:
EHLO localhost
250-smtp.<mycompanyname>.com. Hello localhost (127.0.0.1)
250-AUTH PLAIN LOGIN
250-DSN
[Code]....
As you can see, 250-8BITMIME is not listed here. From the bit of research I made, I found that most MTAs send this by default. Is it possible that the characters from the German language are causing this problem?
NOTE: This problem did not exist or was never reported until now. No one has made any changes on any settings on the server.
I've recently upgraded my Lenovo Sl500 laptop from windows vista to windows 7, both 32bit.
Prior to this i had dual boot between CentOs 5.6 and windows vista.
After i have upgraded to windows 7, the dualboot is apparently gone, I am no longer able to boot in linux.
My question is now, how can i fix this, or create a new dual boot?
Im currently left with two partitions, one with Windows 7 installed, and one with CentOs 5.6 installed, but as said, I am unable to acces my linux.
I am running into a problem with my xen installation. So far I have:
- installed 11.4 64bit
- installed hypervisor and tools (I created br0)
- boot into xen kernel
- run a zypper update
My current configuration is:
Linux linux-c7sq 2.6.37.6-0.7-xen #1 SMP 2011-07-21 02:17:24 +0200 x86_64 x86_64 x86_64 GNU/Linux
using patterns-openSUSE-xen_server-11.4-6.9.1.x86_64:
- bridge-utils-1.4-63.1.x86_64
- xen-doc-html-4.0.2_02-4.9.2.x86_64
- xen-doc-html-4.0.2_02-4.9.2.x86_64
code....
Does anyone have the same problem? There was nothing on google on this, and the xs_handle cannot be debugged as xs.so isn't visible to me.
I merged my toolbars into one toolbar. This results in having my bookmarks toolbar next to my URL bar.
The problems is that the URL bar apparently chooses the biggest width available with priority over the bookmarks bar, being merged into simply an arrow, which I have to click in order to see my bookmarks.
I would like to give my URL bar a fixed width so that I can see my bookmarks toolbar or to leave the URL bar with a flexible width as long as it doesnt have priority over the bookmarks bar.
I just ran Computer Janitor on my computer and I think it broke Synaptic. The program was cleaning up some files, but then it froze halfway through and I had to force it to quit. Since then, I can't open Synaptic package manager, the Ubuntu Software Center, nor Computer Janitor itself. When I do they either freeze and I have to force them to quite or they just don't show up on the screen, but they're stuck running in the background because System Monitor reports the processor is running at 100% and so I have to go in manually and kill the bad processes running in the background. Restarting doesn't change anything.Running Lucid Lynx on a HP dc7100, P4 3.2 Ghz, 2gb RAM.
View 2 Replies View Related