I ran a full installation, which seemed to work fine but when it finished all I get is a black screen. I suspect the GEForce 9400GT Graphics Card but what do I do if it is related because I cannot see anything?
View 3 RepliesI have been using OpenSuse at work for years. My Windows 7 machine crashed on me. Instead of spending the time to fix it, I decided to take the plunge and install 11.2 on my home system. I have 4 one TB drives. My RAID card has a 2x2 1/0 RAID array defined (sdb, sdc, sdc, and sde). A fifth hard drive, outside of the arrary, which is a 250GB drive (sda). It is a software RAID. Here are the partitions I set up in the installer.
On the raid:
1.75 TB on /home
2.01 GB on swap
48.55 GB on /tmp
Off of the raid:
sda1 115 GB /
sda2115 GB /boot
(I know these are really big but I did not want to put any data outside of the RAID) In the final Installation Settings screen, I chose Booting and change from booting from the MBR to the /boot partition. The boot loader type is Grub and the status location is at /dev/sda2. I select Install and it installs without any error message.
After it installs, it restarts and I press ESC to see what is happening. It skips boot.cycle and continues to load to "starting HAL daemon ...done" and then the cursed black screen. I cannot SSH into it. It just sits there and I have to do a hard resest. Once I restart it, it boots into the non-RAD drive I get the follwing error message:
GRUB ..(it went to fast for me to get the rest of it)(hd1/1) message: file not found and I get the option the change the boot options of the Desktop -- openSUSE 11.2 and Failsage -- openSUSE 11.2 . I select e to edit the boot section of desktop and see
root (hd1,1)
kernal /vmlinz-2.6.31.5-0.1-desktop root=/dev/disk/by-id/ata-ST32508...
intrd /initrd-2.6.31.5-0.1-desktop.
I tried changing the root (hd1,1) to 0,1 1,0 2,0, etc with no luck.What do I do? I need to boot into OpenSUSE and finish the cursed installation.
PS: You can tell I work IT with the uber amount of details I put into this
I have a problem after "Loading Linux Kernel - 100%".It mean when I chose "Installation" or "Check installation media" after boot screen, I see "Loading Linux Kernel" from 0% to 99% and after that I see only Black screen for long time. Even NUM LOCK key or Ctrl+alt+del has no resultThere is no a problem with 11.2 and 11.1(current OS).Machine: HP xw8400, 2 CPU XEON 3.0Ghz, 4GB RAM, 2x250GB HDD SATA, NVIDIA Quattro FX 1500 256MB.The same problem with VirtualBox (on the same PC).
Last line in "text mode Installation" is :
...
[ 0.040974] Checking 'hit' instruction... OK.
[code]....
Configuration: AMD 2500+, 2GB RAM, ATI HD3850 AGP
Problem: Can not install OpenSUSE 11.3. Boot from the disc - the installation screen resolutions, modes of installation - everything is in order. But when the installation can proceed - loading (logo) and just a black screen - possibly the installation goes - but no picture. Also try to set mode "vesa" - loading equipment "ok" ... "ok" ... "ok" ... "ok" ... and again in the black screen.
I had 11.3 running for quite some time without any problem. The upgrade to 11.4 was ruined for some reason (only got commandprompt login) and the message that Xorg.0.log couldn't be copied. Decided to install 11.4 from scratch, but since the install my screen flashes every 20 seconds or so to black screen and and after 1 second back to normal. There is no interruption of any other task like typing. Card: FeForce FX5200 card. Can someone please point me to a solution? Also, my monitor (Philips 150S) is not recognized. How can I change that without changing xorg.conf by hand?
View 1 Replies View RelatedI can't seem to get Ubuntu to run on my old Dell Dimension 2300. It boots to a purple screen then it goes to a black screen with a load of writing nothing else happens after this screen. [URL] Could someone advise how I can get it to work?
View 1 Replies View RelatedI have openSUSE 11.3 with an nvidia card connected with two monitors. In the past I used xinerama which was ok, but now I need to have two separate desktops, one on each screen. I set the nvidia driver with x screen, and now one screen works perfect and the other only shows a black screen. When I move the mouse over the black screen, the mouse pointer turns into an X, but moves correctly, which seems to me that the problem is that I need to set the second desktop to that screen. I looked on forums on how to do so, and no luck.
View 1 Replies View RelatedOpenSuse 11.3 with nVidia drivers.I have the screen working fine though it only runs in 1600x1200@75 using the nVidia driver (GTX260 card).When I play a game in full screen mode all seems OK but when I exit the game then I just get the mouse pointer on a black screen.There must be something present since the cursor changes as I move it, normal pointer -> hand over a link etc. It's just that black on black isn't very readable.
View 5 Replies View RelatedThis obnoxious bar has just appeared in Smplayer at the top of the screen. It stays there even when I go full screen. Now full screen isn't full screen and there are black edges on both sides of the screen. I have not be able to figure out how to hide it. I do not need or want this onscreen display. How can I configure Smplayer to make this go away? How can I get my 16:9 full screen aspect ratio back? I have done nothing to mplayer or smplayer as far as editing any or changing any configuration files. I tried several videos and it displays on all of them. It was not there last time I used Smplayer.
View 9 Replies View RelatedI was messing around with the screen orientation and thought it would be funny to orient it sideways. Big mistake The screen went black.I can force a shutdown, login and I get the same black screen. I tried hooking up an external monitor and the monitor showed no input so I'm guessing my laptop doesn't have that capability with Fedora.This is my main computer.
View 14 Replies View RelatedI try to install openSUSE 11.4 KDE RC 2, unfortunately I show black screen after GRUB screen. I must press Power button to turn off my computer. I hope it won't on openSUSE 11.4 stable. I'm waiting for downloading openSUSE 11.4.
View 8 Replies View Related'm trying to duel boot windows 7 and ubuntu 11.04 on an Acer Aspire 5736, but when I try to boot from the cd (which I burned with InfraRecorder) it first goes to a black screen with a blinking under score in the corner, then to a purple screen with a couple symbols at the bottom, and then the screen goes black and nothing else ever happens
View 4 Replies View RelatedAfter succesfully installing Ubuntu 10.4 x32 and rebooting pc hangs on black screen with a flashing white dot in the top left corner of my screen, i've tried installing it twice with the same results.
my setup is: Asus p5q-e,
4 gig of corsair dual ram,
ati 4850 graphics,
onboard audio.
ahci mode
win 7 installed on intel ssd, and xp on a samsung 320 gb sata 2,
i had this configuration running fine for 2 months without boot loaders,
on pc start up i choose from which hdd to boot from.
i installed ubuntu on the samsung drive where it was recognised fine, wiped it all and installed automatically.
pls let me know if there is anything i missed, and advice if possible in what to do.
thanks
kannanni
another post about this. I just don't know how to handle this, as I'm pretty nsee the grub loading menu, but screen just freezes after, no way I can reboot, or open a console. In recovery mode I can log as root in console, though.I run Debian 6, 64 bits. I have an intel q6600 and a nvidia geforce 9800GX2.
View 9 Replies View RelatedA recent OpenSuse 11.2 update is causing one to view a black screen with an X in the Tight VNC window of the remote machine when connecting with VNC Viewer (i.e. vncviewer IPAddress:1 ) in a console. I have two OpenSuse11.2 machines (one with no updates since 11/2009) and one I updated this week (12/16/2009). I am able to successfully use Tight VNC to connect to the OpenSuse11.2 machine without recent updates but get a black screen when attemmpting to connect to a recently updated OpenSuse 11.2 machine. My source machine is also a OpenSuse11.2 desktop with current updates.
View 8 Replies View RelatedI've got a problem with my openSuse 11.3 for a few days. This is my first Linux so i'm kind of rookie.OK, let's start.I installed it something like 1 month ago and everything looks good until now. When I turn on my PC and try to login (deskop mode) login bar goes from 30% to 50% and then appears a black screen, nothing more, just deep black (cannot type anything etc.) I use GRUB - Windows, opensuse deskop mode and failsafe mode. Failsafe mode works good, but I have no idea what should I do because I didn't change anything. I even done a reinstall of OpenSuse and after one day I've got the same black screen.Someting wrong with grapfic card drivers? (ati 4850, downloaded from ati page, works good for 1 month) maybe some kind of new update which was installed automatically?
View 3 Replies View RelatedVNC is still now working with xinitd.d. I have done a standard installation with KDE and start VNC with xinitd.d. The system is fully patched. The VNC client connects but the screen remains black. All hints on the internet (IPv6, displaymanger) don't work for me.
View 5 Replies View RelatedSeems to happen with every version! I have the same problem as my last thread. Basically it was solved by removing an IPv6 line from the hosts file or adjusting the vnc configuration to use an IP and not host name. Both of these are not working for me on 11.3. I'm not seeing any errors in log/messages. It just sits there with an X cursor that moves around then times out after around a minute or so. I don't know if there are any other logs that will help.
To clarify, starting a vncserver from a terminal will work, but the 'Remote administration' vnc with the login screen will produce a fully black screen with an X cursor that updates with my mouse position.
I have the all the latest updates from yast. I recently installed the nvidia drivers. I have a black fuzzy line near the top of the screen. At the task bar(bottom of the screen.), all the menus now appear at the top of screen.
View 3 Replies View RelatedI'm running openSUSE 11.2 on a Thinkpad T61p with nvidia graphics. I'm running the proprietary nvidia driver.The battery ran very low and the computer suspended itself. After I woke it up, the desktop is completely black.After troubleshooting as much as I could, I did ctrl-alt-backspace, which brought me to a normal (non-black) login screen. However, as soon as I logged in, I was back to a completely black screen. But the system is operating.I rebooted the computer (warm reboot as well as cold restart) and each time the video is normal until I get to the desktop and all I get it black.Everything was normal until the pm suspend.Suspend has never worked exactly right, so I don't normally use it. But in this case, it used itself Next step: I logged in to console mode and looked at the logs. The only messages of interest seem to be in Xorg.0.log I found a couple error messages that might be of interest:
(II) LoadModule: "nouveau"
(WW) Warning, couldn't open module nouveau
(II) UnloadModule: "nouveau"
[code]....
I'm on a JFK assassination binge right now
Every ten minutes or so the screen goes blank and I have to hit the keyboard or wiggle the mouse to bring it back to life
This isn't hibernation...for the audio still works
I've looked around the control center...right clicked the desktop and looked at options there
I have registered a problem similar to the one reported in this thread: Solution to black screen problem in opensuse11.2 - openSUSE Forums
after installing openSUSE 11.2 from DVD, and rebooting the system a blank screen appears after booting process is completed.
Initially, I was thinking that was 'cause of the installation of ndiswrapper drivers (see command "modprobe ndiswrapper" not working - openSUSE Forums) but after the 4th (!) installation of openSUSE I really don't know what to think...
Sometimes openSuse boots regularly, and sometimes not... seems that there is no difference if I restart the PC or I turn it off and then off. Result is the same: sometimes I get the user desktop and sometimes not...
As explained in my previous post, I have checked the disk but all seems ok.
Now I cannot use the PC even in failsafe mode... I get always a black screen.
But what is more surprising is that I have 2 identical (identical!) PC with the identical hardware, and identical bios configuration. Only the monitor is different. Well, said that, one is working the the other one not...
To be honest, the working PC was an openSUSE 11.1 systems updated to openSUSE 11.2.
I think that must be something wrong on the distributed openSUSE DVD..
I tried both installing 11.3 on top of 11.2 and a new install with the same result on a couple of different mac pros (with 2009 ATI Radeon HD 4870 with 512MB of GDDR5 memory, 2.66 GHz 2x4 core Xeon 3500, 24 GB of memory). The install was done via the downloadable dvd from opensuse.org. The graphics of the install process looked fine as well as the configuration. When it came time to boot, however, the suse splash screen showed up and then the monitor went dark. The graphics seems to be frotzed. Now attempting to boot from the DVD does not cause the display to do anything. Even putting a mac DVD restore disk (and using C during boot) does not result in anything on the display). Any ideas of what the installation could have done -- seems like a no-brainer that something is screwed up with the graphics card, but I have no real proof and even less idea of what to try next.
View 2 Replies View RelatedI very frustrated at this point. I have tried to boot OpenSUSE 11.4 from the usb flash drive iso and CD iso. After I restart my computer the boot menu comes up and I click the boot option and the screens loads a bit and then goes black. I have also tried the text installer, but that doesn't work either. I know the problem must be my graphics chip. I have a integrated Intel HD Graphics chip. My laptop is a Gateway NV79. How can I get the graphics to work?
I've tried everything I can think off. I'm not the most computer savvy so if someone replies I would appreciate a dumb-down explanation on what to do with clear steps, if possible. Note: I'm dual booting with windows 7. The graphics problem is not just OpenSUSE. I tried Ubuntu 11.04, Kubuntu 11.04, Fedora 15 and they all have the same problems. In Fedora 15, I was able to boot in but I got an error message that said Gnome 3 fallback and I couldn't get the graphics to change to standard mode
Problem-PC automatically boots into a black screen with blinking cursor. No message or nothing
I have 4 HD. Primary drive has Windows Vista, Secondary no OS installed. Sata1 HD Ubuntu 10.04, Sata2 Windows 7. Prior to installing windows 7 all was perfect but once I did it, grub got all screwed up. The only way I can boot into grub is if I manually select my Sata1 which has Ubuntu on it and only then it allows me to select Linux or Windows OS. How can I change that so it can boot up normally as before? I'm assuming that grub was installed in the primary drive which has vista on it, but once I installed windows 7 it got deleted and when I tried reinstalling Ubuntu, the grub was not installed in the primary drive.
I have spent the better part of 2 days perusing these forums for assistance. Here is the short story:I run a 7 year old custom build with a 82865G Intel Chipset and a NVIDIA FX5200 graphics card. Had been running a sluggish XP and after adding 2GB of fresh RAM wished to start fresh with my old friend, Ubuntu.
I've tried 10.04 LTS with and without my NVIDIA card installed with no luck. I have successfully installed 10.04 using the alternate install, but this also goes to black. I can hold shift to see GRUB and play around there, but no luck so far. I've also tried 9.10 but have not gotten past the pulsing Ubuntu image. I've seen plenty of support for NVDIA and Intel onboard graphics chips suggesting boot commands like nomodeset and i9015.modeset=0/1...it's all falling short.
I'm heavily leaning towards just installing an earlier LTS or a different linux distro all together. If there no one can help me debug, maybe someone can suggest a distro that will make me happy.
I've installed ubuntu 10.04 onto my Dell Latitude e6510 (through the wubi installer), but I can't get anything except a black screen. I'm pretty new to ubuntu, but after a bit of looking around at graphics issues I found a bunch of boot parameters and tried different combinations of them. i915.modeset=0 Gave me the purple loading screen, until the screen went black and I got flashing caps lock and scroll lock lights.xforcevesa gave me a completely black screen -- not receiving power at all
I also tried noapci, acpi=off, irqpoll, and pci=routeirq as parameters. None of those had any success.I've also tried letting ubuntu boot with a black screen until I heard the African drums and pressing Ctrl+Alt+F1 to go into the console, but the screen stayed black then as well.
Opensuse 11.2 remote administration. If configured at vnc and www (5901 and 5801) port we got just a black screen. No firewall to block it
View 9 Replies View RelatedI played a bit with plasma widgets and every once in a while everything crashes, I see only black screen and have to restart. After restarting everything worked normal. I found some tutorials for opensuse, and started with some basic shortcuts, such as showing active windows and activities. Then I had black screen again (which I've come accustomed to) and restarted pc expecting everything will be just fine like it was after previous reboots.
But then I saw that all activities are identical and everything I worked on has been deleted. I found in activities window that I have 20 or more activities and I didn't know where they had come from. I am stuck and I didn't see any activity that will restore my desktops to original state, and in my searching through activities I also had a lot of black screens. I use opensuse 11.4 x64 and kde 4.6.
opensuse v11.3
linux 2.6.34.7-0.5-desktop x86_64
ati radeon hd3200 (builtin to mb)
fglrx driver - distribution-specific build
At random intervals the video output is turned off for 2 - 3 seconds giving a black screen. (I suspect the 2 - 3 second blank time is how long it takes the monitor to recover after a loss of input signal.) The interval between events can vary from 1 minute to an hour to more than a week, and recently more than a month. Sometimes I get several per hour; other times not for two weeks. Hmm, there was a kernel update in the last week or so.At one time the cause was pointed at a USB driver problem since a number of USB log entries occurred at the same time as the screen blanking. That is not the case here;here is nothing in </var/log/messages> (or the dmesg output) that is anywhere near when a screen event happens.