In the ipv4 code i was using "ip_mc_join_group()" to join the multicast group. but i cannot find a similar function for ipv6 i have found one ipv6_sock_mc_join() but this function is not available for use with my module as it is not exported.
View 1 Replies
I have a PC connected by ethernet to a Galil motion controller card.I recently installed Centos 5.The Galil software for communicating with the card is reporting that it can't join a multicast socket group.The software used to work with another version of Linux.
View 6 Replies View RelatedHow can i make my device join a multicast IP group.My target device is in linux
View 2 Replies View RelatedI am in verse to test "Multicast Packet filtering".I want to setup Virtual Machines to be servers with bind option set to a multicast group address of 225.0.62.87.Then I want to configure the client VM, connecting to the multicast group address and setting the TTL as needed.
View 3 Replies View RelatedI used to play with gw6c ( a client for tunnel broker ) It works well with fedora9 , fedora 10, but not with leonidas. my rpm is gw6c-6.0-0.4.beta4.fc9.i386.rpm ( a little old!) when I tried to install i have got this: libcrypto.so.7 est ncessaire pou w6c-6.0-0.4.beta4.fc9.i386 I try to make a soft link to libcrypto.so.0.9.8k, but nothing; The question :-Is there a solution for that pb - did you know a better client for non native ipv6 connectivity?
View 2 Replies View RelatedI have been struggling to get FC15 to act as an IPv6 router for a while now, am sure I am missing something trivial.. The idea is that I have a ppp / adsl connection (this works fine), use the wireless card on my pc with hostapd and dhcpd to provide connections to other pcs (works fine), and radvd to delegate ipv6 addresses.
The issue seem to be that as soon as I turn on ipv6 forwarding (net.ipv6.conf.all.forwarding =1), the ppp connection no longer gets an IPv6 address. This means the router cannot ping any ipv6 address outside my network.
If I disable ipv6 routing, my router gets an IPv6 address on its ppp connection, and can ping things such as ipv6.google.com just fine, however (of course) no packets are forwarded from my network and radvd complains that forwarding is disabled.
I am trying to understand the join command. I wish to join two files:
Code:
$ cat test1
a 0
b 2.51
c 19.85
$ cat test2
a 0
b 2.51
[Code]...
this is great but I do not understand why join ignores the -e flag and fails to insert FOO in the empty field.
I have several multicast data feeds that I'm trying to connect to using a minimal server install of Ubuntu as a VM on a VMWare ESXi server.I have another VM on the same server running Solaris that can connect with no issues to the incoming multicast stream.
View 1 Replies View RelatedThis is not a linux specific question more of a general network issue with the hope that someone may have already done this under linux.My problem:I have a red hat linux machine transmitting IP multicast packets onto an ethernet gigabit network (cisco switch).Wireshark (running on a different red hat linux box confirms packets on network.
View 4 Replies View RelatedIf I have set up 2 network interfaces on a box, if I started sending multicast traffic, it will go out through both interfaces? Or is there a way to control through which interface it will go out?
View 1 Replies View RelatedFor the last couple of days, I've been unsuccesfully trying to receive multicast packets on Ubuntu Server 11.04, and seen some strange things along the way. The program i use to test this, is basically http://www.scribd.com/doc/38224328/mcreceive-c.Now the network has been configured to forward me the multicast packets, regardless of the joins. So tcpdump shows me:
Code:
15:16:11.308952 IP 10.164.130.2.61417 > 224.16.17.23.47806: UDP, length 1400
...
[code]....
I've got an application that compiles in Windows and Linux and is using UDP multicast to communicate. I'm running it on a Windows machine, a Linux machine and a small board (Gumstix) that is running Linux as well. The Windows and Linux machines have no problems sending/receiving packets with each other. The Gumstix and Linux machines have no problems sending/receiving packets with each other. The Gumstix can also send/receive packets with two instances of the application both running on the Gumstix.
But when running on the Gumstix I can send udp multicast packets to Windows, but cannot receive them. (It works if I do point to point with a known IP port#, but not multicast.) I can run tcpdump on the Gumstix and see the packets, but they are not being received on my socket. Here's what tcpdump (running on the Gumstix) outputs when sending the same packet from different sources. Notice the IP header ID and flags (don't fragment) are different when coming from Windows.
WINDOWS to Gumstix
-7:-45:-2.015784 IP (tos 0x0, ttl 15, id 35331, offset 0, flags [none], proto: UDP (17), length: 444) 172.30.42.3.1165 > 239.255.183.180.47028: UDP, length 416
LINUX to GUMSTIX
-7:-43:-38.451991 IP (tos 0x0, ttl 15, id 0, offset 0, flags [DF], proto: UDP (17), length: 444) 172.30.42.13.32771 > 239.255.183.180.47028: UDP, length 416
GUMSTIX to GUMSTIX
-7:-33:-10.955608 IP (tos 0x0, ttl 15, id 0, offset 0, flags [DF], proto: UDP (17), length: 444) 172.30.42.110.1025 > 239.255.183.180.47028: UDP, length 416
I've tried everything I can think of to get this to work but am not getting anywhere. Also I'm pretty inexperienced when it comes to Linux. Anything I could try to be able to receive udp multicast packets from Windows?
I have 4 interfaces, dvb0_0 - dvb0_3. Each one has a multicast stream coming in on it. The program I am using to decode these streams only accepts one interface though. How can I "combine" so that the program, listening on 1 ip can get all 4 streams? they are on groups 224.0.1.1-4
View 1 Replies View Relatedhave a doubt about the multicast address.I have read that IP and ethernet multicast address have the same last 23 bits. While an ethernet multicast address always starts with 01:00:5E. Changing the last 23 bits of the IP address into hexadecimal form and "adding" them to the first 24 bits we find the ethernet address but what about the missing bit??? For istance I have: 230.11.111.10 = 11100110.00001011.01101111.00001010 So converting the last 23 bits I have b:6f:a The final ethernet address will be 01:00:5E:b:6f:a . And what about the missing bit?
View 1 Replies View RelatedWe have a high speed udp multicast connection. There are about 37 multicast groups and average incoming rate via the connection is about 20000 pkt/sec and peak 40000+ pkt/sec. Each packet is about 100-300 bytes. And there are 6 busiest multicast groups generating 80% of the traffic. No significant outgoing traffic via that interface. The problem is that, if our heavy-weight application create 37 sockets for all the groups, the packet loss become quite frequent. but if we create the 6 sockets for the busiest groups, the packet loss drops to 1/10 of the original level. We can confirm that the lost packets DO arrive in our box because a light-weight recorder on another box on the same ethernet segment can see the lost packets when listening to the same groups. If we start another heavy-weight application for the rest groups (31 groups ) on the same box, the packet loss just come back to the original level.
The packet loss happens not only to the heavy-weight application but also the light-weight recorder running on the same system. that is, the loss is system wide. The socket kernel buffer are all 4MB max and did not observe system buffer overflow. It seems the number of sockets listening to the same multicast group have the most negative impact on packet loss. And the higher traffic have a far less impact on packet loss than the number of sockets. It also seems that there is some limit in the kernel that when socket number are reduced under, the packet loss can significantly ease. How can I further diagnose the problem? Our system is RHEL 5.3 32bit i386, Xeon 2.9GHZ 16 Processors, 32GB memory. Two broadcom giga netowrk card and 6 Intel GIGA NIC, and only one interface card has so much traffic.
I am trying to run some benchmark tests for multicast. What I want to do is have one system send multicast packets and another receive it on all it's interfaces (eth0-eth3). Whenever I run receiver on more than one interface I get echo effect (if I receive on x interfaces then I get same packet x number of times). Is this how it is supposed to behave? It does not make any difference whether I use loop-back or not. I have set SO_REUSEADDR to yes. I run separate instance of receiver on each interface. I am doing this on RHEL5 systems.
# uname -r
2.6.18-164.20.1.el5
I'm trying to receive data that is being broadcast on address 224.0.1.1, 224.0.1.2, 224.0.1.3, 224.0.1.4. ports are 1201, 1202, 1203, 1204 respectively. I can see the data using wireshark but can not get my program to receive the data. all firewalls are shutdown. iptables is not running, i've set net.ipv4_icmp_ignore_broadcasts = 0 and still no luck.
View 1 Replies View RelatedI have just set up an FC 13 box for a small network application. At the core, the application is supposed to receive some data over a multicast on my local network. However, for some reason, I am not being able to receive any multicast data on this machine. Other machines, on the same network (connected on the same layer 2 switch) are receiving the multicast just fine. I have tried the following things:
1. ensure that I am joining the multicast on the correct interface: the machine has only one ethernet card. Also, after starting my application, I use netstat -g to check for group membership. The multicast subscription shows up fine.
2. ensure there is no error in the program: the program works fine on my person linux machine
3. ensure that the multicast is actually available: it is available on all other local machines. I also wrote my own small broadcaster. data from this broadcaster (running on the same box) is available to other machines but not to my own listener program.
4. no firewall/filtering settings on the layer2 switch
5. TTL setting on the broadcast: have tried changing it from 1 through 5 with no effect. Note that even if the broadcast is coming from the same machine, my machine does not pick it up while other machines on the network do so.
I suspect this has to do with some settings on the network card itself. Below is the output of /sbin/ifconfig on the card:
eth0 Link encap:Ethernet HWaddr 00:08:A1:67:BBA
inet addr:192.200.20.32 Bcast:192.200.20.255 Mask:255.255.255.0
inet6 addr: fe80::208:a1ff:fe67:bbca/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
How can I find out list of multicast addresses and port in use?"netstat -ng" only gives list of multicast addresses that have been joined, it does not give port number.I have several hundred servers running application that listens to several multicast addresses on different ports. I want to write an audit script and get the list of multicast address and port numbers.
View 2 Replies View RelatedI've just set up an LTSP server, with all its clients on a separate subnet to my main network - the main network is 192.168.1.x, and the LTSP clients are all 192.168.2.x. My LTSP server has 2 NICs, one on each network, and is merrily forwarding normal IP traffic from the clients to the rest of the network. I have a client/server application that has a server on one machine, and clients locate and attach to it using multicast protocols. The server is on the main network, and any other machines on the network can locate and talk to the server quite happily. The LTSP clients, however, cannot - I assume because the multicast communications aren't being forwarded by the LTSP server. How I can get this working?
View 2 Replies View RelatedI got a server setup with three nics
eth0 = wan
eth1 = lan
eth2 = iptv (multicast)
When I have my IPTV inserted in the computer I am either having problems connecting to the internet or recieve the multicast streams from the iptv. I do get a valid ip on both the WAN and IPTV, but I am having problems getting them both to work at the same time.
eth0:
eth0 Link encap:Ethernet HWaddr 00:14:d1:1d:72:39
inet addr:94.xx.xx.63 Bcast:255.255.255.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2180753 errors:0 dropped:0 overruns:0 frame:0
[Code]...
I don't know how to join centos v5 to domain cotroller 2k3.
View 4 Replies View RelatedI've installed Ubuntu 9.10 in my office desktop. as a newbie in the world of linux, i really do not know much about it. I want to join my desktop in our domain. i already have the ip addresses of the DNS servers but i dunno where to put it. i've installed likewise open and try to join the domain but it displays the following errors: Manual Configuration Required:
The configuration stage 'open ports to DC' cannot be completed automatically. Please manually perform the following steps and rerun the domain join: Some required ports on the domain controller could not be contacted. Please update your firewall settings to ensure that the following ports are open to 'MARVEL2.LBPNET':
88 UDP
389 UDP
464 UDP
445 TCP
But here is my problem... I have a windows 2003 server mini tower ATX running VMware workstation 7.0 that has a Ubuntu server 32-bit and a Ubuntu desktop; both versions are 10.04. Now, my ubuntu server edition joins active directory just fine, but my ubuntu desktop does not.
Here is my /etc/samba/smb.conf file:
[Global]
workgroup = XXXXDELIGHT
security = ads
realm = XXXXDELIGHT.BIZ
idmap backend = lwopen
[Code]....
I'm trying to join a wireles lab that I've setup with WEP encryption, but I'm unable to join. (I've tried on two different distros: ubuntu, and backtrack) same result.
here are the commands:
Code:
ifconfig wlan0 down
iwconfig wlan0 mode managed
iwconfig wlan0 essid MYNET
iwconfig wlan0 key XXXXXXXX
iwconfig wlan0 channel 3
dhclient wlan0
tries to contact dhcp but none responde to request, and when I do iwconfig, it shows as not associated
I am running Ubuntu 10.10 64-bit on my Dell studio 1557 with a broadcom 1394 wireless card.
I am wondering if it is possible to set my laptop to autojoin open wireless networks. I like traveling and it popped into my head. I am a novice linux user, long time windows user. I know its possible just how. like a terminal script or just a check mark somewhere. i broke my right hand and arm in a motorcycle wreck recently.
but is there any thing i need to make sure on the domain controller for me to be able to join the domain with a linux machine alright?
View 2 Replies View Relatedis it possible to join a Fedora box to a Windows Domain. Will the box be automatically added in DNS?How do I configure Fedora afterwards so I can login with a domain user on the box?
View 1 Replies View RelatedHow do I join a Windows XP Workgroup named HOME?
View 1 Replies View Relatedin searching i never found an article that got it just right. so here it is tried and true..
1. I usually start out assigning myself a static ip address. this is not needed to join but its something I always do.
2. next i set my dns settings in resolve.conf to my local dns server
3. download likewise "apt-get install likewise-open"
4. for kerberos i just leave it blank
5. go to your nsswitch.conf file located in /etc/ and set the hosts to only files and dns
6. now you should stop your networking and start it again so that the dns changes take effect.
7. you are now ready to try and join your domain. "domainjoin-cli join fqdn.of.yourdomain administrator" you can substitute administrator with any admin account
you should now be joined to your domain for adding sudo rights to the "administrator" membership
1. open your sudoers file located in /etc/
2. the following line to the bottom of the file "%DOMAIN\administrators ALL=(ALL) ALL" replace DOMAIN with your domain name. do not use your fqdn. all set. hope you enjoy
