I would like to enable ipv6 forwarding . i have ipv6 module loaded.I added net.ipv6.conf.all.forwarding=1 in /etc/sysctl.conf .i tried reboot , did 'service network restart' .
.
Also I tried
sysctl -w net.ipv6.conf.all.forwarding=1
and
[code]....
Okay I have searched how do I enable ipv6 forwarding?
There is no ip_forward in /proc/sys/net/ipv6/
A command like (single quotes used in the command):
Code:
ssh -L '[::1]:3128:127.0.0.1:3128' ...
is getting an error message like:
channel_setup_fwd_listener: getaddrinfo(::1): Address family for hostname not supported
This is supposed to be an IP address, not a hostname, for the localhost in IPv6. Anyone know what is wrong with this? Addresses like this work OK in rsync. I know I can use ip6-localhost as a hostname. But right now I'm testing actual IP addresses in IPv6 to see what programs can or cannot handle it.
We have on Ubuntu 10.04 LTS installed on one m/c which is connected to office network using pptp vpn.Now i want to enable ip-forwarding on this m/c so that i can connect my RH9 m/c through this. For enabling ip forwarding i did the basic thing "echo "1">/proc/sys/net/ipv4/ip_forward" And added route on the RH m/c as route add -net 10.254.254.0 netmask 255.255.255.0 gw 192.168.1.10 dev eth0" (IP of Ubuntu m/c is "192.168.1.10 and RH m/c is 192.168.1.15) But some how ip-forwarding is not working properly.
View 4 Replies View RelatedHow do you I use duel stack i.e How do I use ipv6 packet inside ipv4 packet using fedora kernel 12 ?
View 1 Replies View RelatedI'm trying to enable port forwarding so I can use my computer as an FTP server to some friends. Here's my setup:
CLEAR wireless modem <--> LAN port 4 on router (not WAN) and LAN port 1 on router <---> eth0 in Ubuntu 9.10
The modem acts as a DHCP server which successfully assigns an IP address to my desktop system. I can also go onto the internet just fine on my desktop, and any other computer that connects to the router.
I have enabled port forwarding on the modem (not the router because it's being used as a switch, and not using its WAN port) to forward ports 21 and 80 to my desktop. What I don't understand, though, is that when I try to FTP to the modem's WAN IP address, the connection is refused. However, when I use websites such as:
www.canyouseeme.org
www.yougetsignal.com/tools/open-ports/
They say ports 21 and 80 are open (and not other random ports like 22 or 23 which I tried to see if the site simply said everything was open) but I cannot access my site from a web browser.
I was wondering what it was that's stopping computers from the Internet from communicating with my computer? The modem? The router? Configs?
Got Ubuntu Server 10.10 installed as a virtual machine (vmware). When i forward X through SSH (putty) i can start xeyes, xcalc,etc.
Now when i disable ipv6 putty can't set the display variable and i get "Error: can't open display". I haven't changed anything in putty or win 7 (the host system).
I disable ipv6 by putting these lines in /etc/sysctl.conf
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1
I used to play with gw6c ( a client for tunnel broker ) It works well with fedora9 , fedora 10, but not with leonidas. my rpm is gw6c-6.0-0.4.beta4.fc9.i386.rpm ( a little old!) when I tried to install i have got this: libcrypto.so.7 est ncessaire pou w6c-6.0-0.4.beta4.fc9.i386 I try to make a soft link to libcrypto.so.0.9.8k, but nothing; The question :-Is there a solution for that pb - did you know a better client for non native ipv6 connectivity?
View 2 Replies View RelatedI have been struggling to get FC15 to act as an IPv6 router for a while now, am sure I am missing something trivial.. The idea is that I have a ppp / adsl connection (this works fine), use the wireless card on my pc with hostapd and dhcpd to provide connections to other pcs (works fine), and radvd to delegate ipv6 addresses.
The issue seem to be that as soon as I turn on ipv6 forwarding (net.ipv6.conf.all.forwarding =1), the ppp connection no longer gets an IPv6 address. This means the router cannot ping any ipv6 address outside my network.
If I disable ipv6 routing, my router gets an IPv6 address on its ppp connection, and can ping things such as ipv6.google.com just fine, however (of course) no packets are forwarded from my network and radvd complains that forwarding is disabled.
How to enable ipv6 in snort. I read that it must compilate with --enable-ipv6 but still don't know how?
View 2 Replies View RelatedWhat determines whether I should enable ipv6 when installing Linux? so not sure whether it depends on my ISP, my hardware (network card or modem or router), my Linux kernel, my CentOS version (5.6), my requirements, etc.
So I'm not sure whether or not I should enable it. And if I were to, in the CentOS installation screen would I select 'Automatic neighbor discovery' or 'Dynamic IP configuration' or 'Manual configuration'?
I just finished setting up my slack machine as a home server (printers & files) and I noticed that I have an IPv6 address (from ifconfig)... I didn't know I did. I used to work in tech support and when a windows or OSx machine didn't connect properly on a LAN, disabling IPV6 was a common troubleshooting step. Is there a way to easily turn inet6 connectivity off/on in Slackware? (I want to keep the ability to get an IPv6, we will all use those in the future)
View 2 Replies View RelatedI have a server that sits between two LANs, and I wish to enable multicast routing from one LAN to the other. I have multicast routing enabled in the kernel but didn't know how to enable it. Tried to add mc_forwarding in /etc/sysctrl but doesn't work.
View 3 Replies View RelatedI installed Fedora 15 to my server. I preffer to work over SSH and I enable X forwarding. My configurational file:
/etc/ssh/sshd_config:
X11Forwarding yes
X11DisplayOffset 10
X11UseLocalhost yes
From my laptop I run next commands
ssh -X user@xx.xx.xx.xx
startx
and the session start on server, no redirect occur. Next output I saw in terminal
[Code]....
how to enable X11 forwarding if I SSH directly into the system, for example:
ssh -X server1
However, I'm trying to get X11 forwarding on a system I don't have direct access to. I need to first SSH into a server I do have access to, server2, then from there I can SSH into server1. I know about port forwarding but I'm not sure how it works with regards to forwarding X11 windows. For port forwarding server1's web page, I'd do this: ssh -L 9999:server1:80 mylogin@server2
Then opening [URL] on my computer would bring up server1's webpage. What is the equivalent SSH command for X11 forwarding so if I typed it and executed gedit for example, that program from server1 would pop up on my Desktop?
I want to share my WiFi internet connection over LAN, so I'm trying to set up IP forwarding. An old tutorial tells me to go to Network Settings in YaST to do this, but that applet says that NetworkManager is now handling all of that stuff.How do I enable IP forwarding while NetworkManager handles my internet connections?
View 2 Replies View RelatedI have just set up shorewall on my router running Arch Linux. The external network is on eth0 and the internal network on eth1.I have set it up for masquerading and that works fine and I can open ports to the firewall. But I'm having trouble with port forwarding to my internal machines.The problem I have is that when port 22350 is forwarded to 192.168.1.3 on my local network, checking the port with nmap from a remote computer gives me:
Code:
PORT STATE SERVICE
22350/tcp closed unknown
[code]....
I have Ubuntu 10.10 installed on my laptop. My ISP natively supports ipv6, but since last weekend, I do not get an ipv6 ip. When I use a live cd however, I do get an ipv6 ip. For as far as I can see, all settings (/etc/network/interface and the settings in network manager) are exactly the same.
Output of ifconfig:
Code:
eth0 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX
inet addr:XXX.XXX.XXX.XXX Bcast:XXX.XXX.XXX.XXX Mask:XXX.XXX.XXX.XXX
inet6 addr: XXXX::XXXX:XXXX:XXXX:XXXX/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code].....
EDIT: is there a way to let the netwerk be automatically configured as happens during installation? It would be nice to start with a clean and new set of network config files as there were just after I installed Ubuntu on my system, without a full reinstall of my system.
I have a problem with my ipv6 connection: although I can't get ipv6 address with DHCP, I can't use ipv6 network. I tried [URL], and the tortoise is static. I want to fix it out , so I use 'ifconfig' to see my network configuration:
eth0 Link encap:Ethernet HWaddr 00:50:8d:ef:dd:06
inet addr:210.77.9.102 Bcast:210.77.11.255 Mask:255.255.252.0
inet6 addr: 2002:d24d:b64:4:250:8dff:feef:dd06/64 Scope:Global
[code]....
Some people told me that the fisrt ipv6 address was wrong and unsuitable for ipv6 connecting. I tried /ect/init.d/networking restart but it didn't work. How can I use the second address as my ipv6 address and fix the problem out ? Now it seems there is not problem with the ip adress but the route. After watching some video, I suddenly could use ipv6. I did 'ifconfig' again and nothing was different. However, the result from the command 'ip -f inet6 route' changed: the last default route was gone and there was only one default route.
I have installed Bind 9.6.1 on my linux pc. I have to resolve domain name using IPv6 address. I have made following entry in the /etc/resolv.conf file code...
address of the machine on which Bind is running. The problem is that I am not able to ping open-ims.test domain name. If I use IPv4, everything works fine but how to ping domain using IPv6.
I have also made changes in dnszone file by replacing IPv4 address with IPv6 address and also changing A to AAAA.
I want to add repository using ipv6. So, I add a xxx.repo file in /etc/yum.repos.d/. Just like it:
[sjtu6]
name=Fedora $releasever - $basearch - ftp6.xxx.xxx.xxx
baseurl=ftp://ftp6.xxx.xxx.xxx/fedora/releases/$releasever/Everything/$basearch/os/
enabled=1
gpgcheck=1
gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-fedora-$basearch
I have a networking problem with my computer. Under Windows, the computer can get both v4 and v6 address via DHCP. However, the same computer can only get v4 address under Ubuntu. Does anybody know how to solve this problem?
View 3 Replies View RelatedThe goal: ipv6 connectivity using 6to4 The problem: no connectivity on some internal hosts (mixed win & debian) and no ipv6-web access on any host. Let's start with my external box. It is headless debian lenny dhcp/local-dns & cache/firewall. It has the following interfaces after a reboot:
[Code]...
My understanding is that ipv6 will auto-configure itself and that the radvd file is all that is needed by the external host to give all the ipv6 enabled internal hosts ipv6 web access. My question: How is my external host misconfigured? Or are the problems specific to the internal hosts? I am assuming that I have issues on both the external and internal hosts since some of the internals have golobal ipv6 address and some don't. I do however wish to address the external host first.
I have a host and typing ifconfig I get:
eth0 Link encap:Ethernet HWaddr 00:0E:7F:4F:E4:09
inet addr:130.130.9.9 Bcast:130.130.255.255 Mask:255.255.0.0
inet6 addr: fe80::20e:7fff:fe4f:e409/64 Scope:Link
[code]...
and to do a test i want to disable or delete the ipv6 address, but mainteining the other configured parameters. Looking on the ifcfg config file I have
DEVICE=eth0
BOOTPROTO=static
BROADCAST=130.130.255.255
[code]....
and nothing about IPv6... Then, using ifdown-ipv6 could i remove only the ipv6 address?
I have tried to disable the ipv6 support in ubuntu 9.04 32bit but the /etc/modprobe.d/aliases does not exist so I can't disable the suport as sugested for the previews versions. I need to disable it becouse it is pounding a total maihem in my vamware machines.
View 7 Replies View RelatedI am trying to create the IPV6 socket and was wondering if anybody has any code strip which I can reuse ?
View 1 Replies View RelatedI have a server application that uses loopback addresses to open servers on linux machine.
For IPv4 with one line of configuration I can open many servers according to the mask I use for example with 10.10.10.0/24 I can open 254 servers.
How can I do the same for IPv6 ? I am able to add loopback interfaces but only for one host. Is it possible to add for a subnet ?
If not what is the max number of addresses that I can add ?
I also saw that it add the address only to loopback lo and I can add it to lo:3 for example.
I am wondering how I can share connection with my IPv6 connection.
I am using slackware and ip6tables so far. But the problem is that IPv6 or ip6tables has no "-t nat", so how could I just simply share Internet with the computers behind the firewall?
I want to know if sysklogd supports IPv6? I have downloaded latest version of sysklogd, which is 1.5 version. But, I didn't see any information about ipv6 support.
View 1 Replies View RelatedHey even I'm not able to telnet to IPv6 address on port 23
View 2 Replies View Related
