I have a Gateway DX4850 I7 cpu computer. It has a Ralink 3090 wireless card. 64 bit system. What, in your assessment, is the best distro to work with such a card? I CAN hack stuff. I would prefer not to. I've heard that fedora 15 is to be avoided, but have no experience with it.
View 1 RepliesI'm planning to upgrade to 11.4. Is Ralink 3090 wifi adapter is supported in it or not??
View 6 Replies View RelatedI am running Ubuntu 10.04 (32-bit) on a MSI A5000 which appears to have a RaLink RT3090 wireless card. So far everything seems to work except the Wireless card.
The problem is that no option for wireless appears in the network manager, it only shows the options for wired connection. This computer does have a button on the front to enable/disable wireless and I have confirmed that is is on, as there is a green indicator light showing this.
Can anyone tell me the status of the RaLink RT3090 with Ubuntu 10.04? I have looked through various posts here about getting this card working with earlier versions of the OS, where complicated procedures with mixed and apparently intermittent results are described. Do these measures also need to be followed with 10.04?
I have attempted several older solutions found in assorted threads here and I am still unable to get the card to even so much as show up in the network manager. The proceedure which seemed the most promising is here [URL]
I have an HP DV6 3143se which has a Ralink 3090 wifi card in it.the only thing that doesn't work at the moment is the Wifi. I tried installing the Linux backports module, but the trouble is that sometimes, my home wifi network is shown on the list of available networks and most often, it's not. when the network does show up, and i click on it and enter my WPA2 password, it takes ages to handshake and then it tells me that my password is wrong. the same password works in windows 7 so something's not working.
when i try to disable and re enable wireless network on the network manager applet, i get a Wireless device not ready or Network manager not running message.
[Code]....
In a nutshell, it outlines a rather daft snag when running Ubuntu (10.04 and on) with regards to strange and quite frankly ludicrous wireless behavior concerning RaLink cards in Asus netbooks. The M.O. of a netbook is portable netz, yet it seems ENTIRELY impossible with this hardware setup Any geniuses care to have a stab? All outputs are included in the original post.
View 1 Replies View RelatedJust discovering Linux. Couldn't expect everything to work right away, of course. I has some issues with the x11 (the GUI wouldn't show itself), but have gotten around that. Next is WLAN. I have a Motorola USB stick whose chipset i've identified as the Ralink T2501.
It won't show up in YAST as a WLAN adapter, but does in the USB devices attached. I've procured what the sticky advised, and this is it:
HTML Code:
40: USB 00.0: 0000 Unclassified device [Created at usb.122]
UDI: /org/freedesktop/Hal/devices/usb_device_148f_9021_noserial_if0
Unique ID: CiZ2.Q1gxt8A0_KF
Parent ID: uIhY.3f5c44ENLJ9
[Code]....
Anyway, i've downloaded the necessary driver (rt73), but don't want to leap into installing it before i consult you guys. Where do i go from here?
Desktop PC with Trendnet TEW-642 PCI wireless N adapter (Ralink 2860 STA driver). Running openSUSE 11.3 X8_64 with KDE 4.4.4. Software Management and KNetwork Manager both identified rt2860STA as installed. However, KNetwork Manager's authentication window keeps popping up every few seconds and I cannot get wireless.
1) uname -r:
Code:
2.6.34-12-desktop
2) /sbin/lspci -nnk:
Code:
03:06.0 Network controller [0280]: RaLink RT2800 802.11n PCI [1814:0601]
Subsystem: RaLink Device [1814:2860]
Kernel driver in use: rt2860
3) dmesg:
Code:
[ 6.270671] rt2860sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 6.275290] alloc irq_desc for 21 on node 0
[ 6.275294] alloc kstat_irqs on node 0
[code].....
I have downloaded and extracted the latest rt2860.bin file from the Ralinktech website to Desktop but even as root I cannot copy it to /lib/firmware or replace the existing rt2860.bin file in /lib/firmware.
I recently read over here: Getting Your Wireless to Work : "For example, open-source firmware for the Broadcom BCM4306/3 BCM4318, and BCM4311/1 was just released. Future openSUSE versions will be able to include this firmware and those devices will work immediately..." I am looking for PCI cards for desktops. Besides the list of supported chipsets at [URL], is there a brand name list with firmware support by OSS 11.3? At the moment, I have a Netgear WG311v3 which believe has been causing system instabilities in both linux and windoze:
01:06.0 Ethernet Controller [0200]: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11 b/g Wireless [11ab:1faa] (rev 03)
Even with both machines in the same room, I'm only getting 1Mbps when using a pair of TL-WN321G wireless USB adapters to link my main box and my laptop. I'm using Fedora 11 on both machines. It is just as bad if I use the laptop's built-in wireless. lsusb shows the adapter uses the Ralink RT2501USB chipset. iwlist wlan0 rate gives "wlan0 unknown bit-rate information."
View 1 Replies View RelatedI recently purchased an MSI A5000 notebook, but regrettably it happens to use an obscure branded wireless card that's given me quite a bit of frustration to get working. I do have a bit of history behind this card that might help to solve this problem. First of all the card is a Ralink rt3090STA, and the manufacturer does provide a linux driver for this card (available here)
I was using Ubuntu 10.04 32 bit until last week, when I decided that I would like to try using a 64 bit system. I would prefer to use fedora instead of Ubuntu for the time being. Ubuntu had some major problems recognizing the card for some time before I was able to get it to work. The process I used to resolve the issue on my Ubuntu system has not proven successful on Fedora 13 x64, and I would like any help I can get to try to resolve this problem.
I have installed opensuse 11.2 on a second partition, with the ultimate aim of leaving windows altogether. Unfortunately, I seem to be having terrible trouble (as do many others) getting my wireless internet connection working. I have viewed lots of posts in these forums and done everything I can think of, but since I am a linux novice, am unable to identify the problem. The card is working, since it can identify local SSIDs, it has been set up (to the best of my knowledge) correctly in YAST, but nothing seems to work.
I'll include some information I have recorded from my system.. I typed the commands below with the accompanying output listed:
[Code]....
About a year ago I had a different computer with this same wireless card (edimax EW-7128g) and it was recognized immediately after I installed ubuntu 8.10. I found this hardware compatibility page, and it says it is compatible, at least on 9.04.
After reading this old guide I found:[URL].. I downloaded the latest driver, and followed the instructions (i had to refer to the readme too, some things were slightly different which I'm assuming is because it's the 2010 driver not the version referred to in that tutorial) up until:
(e) copy the rt61.ko driver file to the modules directory then load it
Code:
$ sudo cp rt61.ko /lib/modules/`uname -r`/kernel/drivers/net/.
$ sudo depmod
$ sudo modprobe rt61
I don't see where rt61.ko is.I've got the information for my wireless connection edited into /etc/Wireless/RT61STA/ rt61sta.dat iwconfig shows pretty much default stuff, no mention of my wireless card or any type of connection, though the card does show up at the bottom of the lspci query. I added the wireless connection information into the "Network Connections" prompt in the preferences, but obviously that's not accomplished much of anything for obvious reasons. Should I just install 9.04? Judging from this account, getting this wireless card to work would be a hell of a lot easier.
I installed the driver from Ralink (2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO) and followed the instructions in other threads and my card does not work. I am getting this message.
"$ dmesg | grep -e rt5 -e wlan
[ 14.454006] rt5390sta: module license 'unspecified' taints kernel. I have also installed the Ralink RutilT program using synaptic. I can see my wireless device and many others around me but I can't connect.
I have recently upgraded my USB wireless network connection for one of my computers to N from G. As I am (temporarily) based in China the device (and all documentation) are in Chinese. I THINK it is based on a Ralink 28XX chip. I am running Ubuntu 10.04. Network Manager claims that the wireless network is disconnected does not list any sources This is the basic info that I am able to find (I am using these commands in ignorance, by the way!) lsusb shows:
Code:
Bus 002 Device 002: ID 1d57:d2d1
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 148f:3070 Ralink Technology, Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
dmesg shows (after plugging the thing in):
Code:
[ 2081.028069] usb 1-1: new high speed USB device using ehci_hcd and address 5
[ 2081.178000] usb 1-1: configuration #1 chosen from 1 choice
[ 2081.208886] phy2: Selected rate control algorithm 'minstrel'
[code]....
I recently installed CentOS 5.5 on a Acer Revo with RaLink RT3090 wireless card (RaLink RT3090 Wireless 802.11n 1T/1R PCIe). Everything works great except for the wireless card. I've looked at the ELRepo repository, but there is no support for this particular driver. Has anyone had any success with this card or am I stuck with no wireless.
View 9 Replies View RelatedI have recently installed Fedora 10 onto my PC, dual booting with XP, and I am fairly new to linux. I have been trying to connect to my wireless network, but cannot even get Fedora to recognise my wireless adapter (Belkin N1 +MIMO). I have tried to follow a few tutorials that go through either the ndiswrapper method or by using native drivers. Because I don't have an internet connection on Fedora, I have to boot into XP to download the files for either ndiswrapper or the native drivers, rather than installing using the terminal.I downloaded the ndiswrapper RPM, and it failed because of an 'unexpected error', and when using the tarball, it could not find the makefile. The native drivers did not install because of unresolved dependencies.
View 11 Replies View RelatedI just installed Fedora 13, and now I figured, maybe I don't know so much about pc anyway. Before I tell you my problem, I would like to say that I know a lot about windows, but about linux, I don't know anything. A plain beginner. And about my problem, it's more like a "how to" question than a problem.
You see, I don't know how to set up the wifi? The pc has installed wifi, and all I need to know is how I can connect to the internet. In windows you would usually just press the connection icon and then choose witch network you would like to access, and then eventually type in the password, and there you go. But it seems it's a little more advanced at Fedora. But I will give it a shot.
I'm very new to openSUSE, so I need easy, clear instructions on how to install the driver for RaLink RT2561T wi-fi card. I have the driver and everything, I just don't have a clue on how to install it!
View 5 Replies View RelatedI just purchased a RALINK WIRELESS G PCMCIA WIFI CARD VISTA/LINUX (UBUNTU).
It is supposed to be UBUNTU plug and play out of the box with no driver downloads needed.
I installed it but could not find a way to search the active Wi-Fi networks available like on my Actiontec card on windows xp. The wireless router/ethernet I have is an Actiontec setup for Qwest-DSL and Actiontec is the name of the wireless network.
Strangely I tried to choose setup a "new network" and entered Actiontec as the network name and it found the network and said it was connected to it. However the internet still is not working?
Has anyone ever heard of this card or have knowledge of how to configure it to allow me to get on the internet?
View 1 Replies View Relatedthis is my first attempt to get into Linux (10.04 Lucid Lynx), and I'm eager to learn. The problem is however that i can't connect to the internet using my USB wifi dongle (Jensen 25150). I've tried what this link says:I've tried to blacklist rt2800usb, rt2x00lib, rt2x00usb and rt2870sta and to load "/etc/modules/rt3070sta", but no luck in that, so I simply do not know what to do next. Perhaps I haven't blacklisted them the right way? I've typed in the commands and saved Gedit and closed it. Is that the right way?
View 2 Replies View RelatedI just want to setup adhoc network using the wireless card that came with the box but I'm having a hard time getting it up. I have gone through a lot of posts about wireless troubleshooting but nothing has solved it. Left clicking the network manager tray icon always says wireless network is disconnected. "Enable Wireless" is checked.
Some info:
Code:
rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
[Code]....
I been having trouble getting my rt2070 wireless usb card to work on my desktop. I am using Ubuntu 10.10.
[URL]
Pastebin of dmesg: [URL]
Code:
Representative portion in case pastebin wipes this entry:
[ 234.984025] hub 1-0:1.0: Cannot enable port 8. Maybe the USB cable is bad?
[ 234.984041] hub 1-0:1.0: unable to enumerate USB device on port 8
[Code].....
I've ubuntu 10.04 and I can't connect to router wi-fi with my new wireless adaptor usb (ralink 2870). I've tried various guides but nothing. The adaptor work fine with Windows and other linux distributions.
View 5 Replies View RelatedIm a Linux newbie and am running OpenSuse 11.3 (Gnome, 2.6.34.7-0.5-desktop Kernel) and Ive an Asus N13 wifi dongle (linux compatible). I currently connect using my laptopś internal wifi but I bought the dongle due to trouble with weak signal. It came with some sort of code that can be "compiled" but I havent got a clue how to do that (and I have been researching this matter for quite some time now). I then came across a post where someone with the same USB stick created and added only two small files to his filesystem and it worked...for him (maybe becasuse he was on a different Distro )
Ralink RT2870 USB Stick and created the two files mentioned in the post (network_drivers.rules and network_drivers.conf) and placed them in ETC... etc, etc! I rebooted the system but NetworkManager only lists it as "device not ready" ... So now back to square one.
[Code]...
Just purchased this USB wifi NIC. installs and work perfect under Win XP, how ever I can't seem to get working on my opensuse 11.3
Network manager did not recognize the NIC out of the box (still doesn't) so I started trawling the forum and I've read both wireless 'stickys'.
When out of the box did not work I installed the rt3070sta-kmp-desktop - RT3070 Wireless Lan Linux Driver from the repos.
My Nic and kernel version
Code:
lsusb
Bus 001 Device 004: ID 148f:3370 Ralink Technology, Corp.
uname -a
XXXXXXXX 2.6.34.7-0.5-desktop #1 SMP PREEMPT 2010-10-25 08:40:12 +0200 x86_64 x86_64 x86_64 GNU/Linux
[Code]....
I use Ubuntu 9.04 and try to get a Sweex LW053 USB wireless card (Ralink RT73/RT2500 chipset) to work. According to the Wiki list in the sticky thread, this one should work "out of the box" since 8.04.
lsusb delivers
Bus 002 Device 002: ID 148f:2573 Ralink Technology Corp. RT2501USB Wireless Adapter
and there is also some wlan0 entry that doesn't look too dodgy when typing ifconfig.
From this I get that my laptop recognizes the card.
I also typed in some numbers such as SSID and DNS server address in Preferences>Network Connections where asked (although the information that I had wasn't 100% what was asked for so I tried to guess what needs to be filled in which fields).
However, I don't get an internet connection (Firefox can't find server...)
What else do I have to (or can I) do?
I'm having trouble installing my RaLink RT2561/RT61 wireless card. It seems that this driver causes problems for all ubuntu users, and I've tried a couple of work arounds, none of which work for me.
Firstly I downloaded the most recent driver from here: [URL]...RT2501PCI/mPCI/CB(RT61:RT2561/RT2561S/RT2661) is the driver I downloaded. Next I performed the following steps:
Code:
robinsjp@home-desktop:~$ sudo apt-get install linux-headers-`uname -r` build-essential gcc
Reading package lists... Done
Building dependency tree
[Code]...
I have strange behaviour on my portable computer Asus UX30. I'm using latest Ubuntu 10.10 release. The main problem, and the most annoying, is a system freeze on shutdown, suspend, hibernate or even restart. For a week I'm trying to find a solution on the web, but no result. From what I noticed, computer freezes when a wireless card is turned off or on. Here are some basic info from wireless card:
Code:
sudo lshw -class Network
*-network
description: Wireless interface
product: RT3091 Wireless 802.11n 1T/2R PCIe
vendor: RaLink
[Code]....
I use Ubuntu 11.04 on a PC clone desktop.With ethernet cable connects automatically, despite compiling wlan0 not connected. Do not know what I installed Ubuntu 10.04 and 11.04 over 30 times and still the same. Try to manually connect to the network connection did not work either hidden and also deal with ipv4 address assigned and neither worked.
1 ) Machine Brand and Model (PC/Laptop):
desktop pc, clon.
2)lspci
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:02.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Graphics Port 0)[code].....
Try setting manually to no avail not know if I did well. Ralink also downloaded from the rt2860sta and then compiled and did not work. Now I went to install Ubuntu 11.04 and change nothing but that which is above is what I have right now in the machine.