Hardware :: Dell Precision T1500 Sound Card Not Found?
May 20, 2010
I am trying to get RHEL4.7 work fully on a dell precision t1500. Everything is working fine except for the sound card. in the specifications it says it has an "integrated High Definition Audio (Rev 1.0 Specification) implemented with a two-chip audio solution comprised of the ADI 1984a High Definition Audio CODEC and the ICH10's integrated AC97/High Definition digital controller"
RHEL4.7 can not detect the soundcard. running system-config-soundcard return no sound devices were found.
lspci returns the following:
00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11)
00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11)
00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11)
[Code].....
View 3 Replies
ADVERTISEMENT
Mar 29, 2010
So I bought a used Dell Precision 390 Workstation and installed Ubuntu 9.04 on it. Everything seems to work fine, except for the built-in network card. Well, the graphics don't really work right, either, but I rather expected that, and I'll get to it later.
Anyway, when I boot Ubuntu and try to get on the internet, it says I'm not connected. When I open Network Tools, in the "Devices" tab, I get three Network device options: Loopback Interface, Ethernet Interface (eth0), and Unknown Interface (pan0). When I click on the ethernet device option, it shows me the hardware address of the interface, that it has multicast enabled, and that it is "Active", but I get no IP address.
Is there something really stupid that I'm missing? Do I need to do something special the first time I hook up an ethernet cable? I don't seem to remember having to do that on other Ubuntu boxes.
View 3 Replies
View Related
Jul 28, 2010
I have recently installed Centos. During the installation, I noticed that only sound was being tested during the installation. Once everything has been installed successfully. I can run Centos with no problem. However, when I tried to switch from one window (browser) to another. The display was slow. Thus, I suspected the driver for the graphic card of my PC is not being installed successfully. When I type /sbin/lspci | grep VGA in the terminal, I get the following output:
02:00.0 VGA compatible controller: nVidia Corporation Unknown device 06fd (rev a1)
03:00.0 VGA compatible controller: nVidia Corporation Unknown device 06fd (rev a1)
Then, I went to the dell support & driver site to download the driver. In the readme file, it is suggested to install dkms first before installing the graphics driver by typing rpm -ivh dkms-2.1.0.1-1.noarch.rpm
I managed to install the dkms without any error.However, when I use rpm to install the graphics driver as suggested by the readme file:
rpm -ivh dell-nvidia-190.42-1dkms_rhel5.3.x86_64.rpm
I get the following errors: error: Failed dependencies:
libX11.so.6()(64bit) is needed by dell-nvidia-190.42-1dkms_rhel5.3.x86_64
libXext.so.6()(64bit) is needed by dell-nvidia-190.42-1dkms_rhel5.3.x86_64[code]....
Since the above errors may be related to the missing packages then I use yum provides and install to find the missing packages. Even I try to install all the matched packages, i still cant install the driver for my graphic card. To be honest, i am not very sure whether I am doing the right things or not. how to solve this slow display problem when switching from one application to another.
View 1 Replies
View Related
Apr 13, 2011
since installation I dont have any wifi on a dell precision m2400, I have installed ubuntu 64bits.
View 9 Replies
View Related
Oct 1, 2010
We have a RHEL5 box with a 2.6.18 kernel up and running (no RAID in use, but the SAS controller is enabled in the BIOS). To expand the storage, we bought a 2TB drive to add to the machine. Currently the setup is like this:
SATA-0 => DVD-rom
SATA-1 => DVD-rom
SATA-2 => empty
HD-0 => old hard disk
HD-1 => old hard disk
HD-2 => new 2TB drive
HD-3 => empty
The BIOS doesn't seem to have any way to list the drive on any of the HD ports, only the SATA ports, so I'm not sure if the drive is being recognized or not. fdisk -l doesn't seem to recognize the 2 TB drive.
I'm going to try reordering the drive ports and try the drive in another machine, but I'm baffled here...
View 1 Replies
View Related
Sep 5, 2009
I am looking to install Linux on a Dell Precision 340 with unpartitioned 17G (scsi) disk space available.
It is a 4-5 year old workstation with Nvidia Quadro2 MXR/EX video controller.
It has a Windows XP Pro installed on the primary partition.
Which OS should I download and install?
Is the X86-64bit CentOS 5.3 an option?
View 2 Replies
View Related
Apr 30, 2010
I have problems with my laptop which runs well until it decides to freeze and it either shuts down or I have to turn it off. After I restart the system there is no hdd check to signal that something really wrong happened. I suspect the nVidia driver for the Quadro FX 770M video card is responsible but I am not sure. Also, firefox sometimes runs sluggish (maybe flash is causing something to overcharge?) and often times the computer freezes when I am using firefox. The funny thing is that all my heavy simulations are not causing problems and often times they use 10GB of swap with no complains. When the laptop freezes I see two keyboard lights flashing intermittently. How can I figure out what is going on? I mean are there any log files where I can look for something or can I setup a log procedure to detect the cause of this problem?
View 3 Replies
View Related
Jul 20, 2010
Actually, the title I was looking for was Belkin Gigabit Ethernet ExpressCard not seen on Dell Precision M6500 with CentOS 5.5 _when system boots with no link on this card_. When I boot this system with a cable connected to the Ethernet port, the card shows up (dmesg, lspci 0e:00.0 and ifconfig). When I boot it with nothing connected, it's like it doesn't exist. I know I could make it work with a loopback plugged in at all times, but am looking for a more graceful solution. Here are messages logs from when it's recognized
Jul 19 15:14:23 mss kernel: sky2 driver version 1.22
Jul 19 15:14:23 mss kernel: sky2 0000:0e:00.0: v1.22 addr 0xf6afc000 irq 193 Yukon-2 EC rev 2
Jul 19 15:14:23 mss kernel: sky2 eth0: addr 00:00:5a:11:45:5b
[code]...
Update: Should have been a little clearer - this card has the Marvell Yukon chipset. I'm trying to identify the part number without ripping out the casing.
View 6 Replies
View Related
Oct 28, 2010
I have a Dell Vostro 3300, i5 460 processor with a NVIDIA 310M Graphics Card. I'm doing a KUBUNTU 10.10 (Maverick) install with the following results. The Live CD boots just fine to, "TEST," or "Install." Installation goes fine. However, the graphics card being used is the Intel i915. I have tried installing the NVIDIA drivers directly from the, "Additional Drivers," tool and after the reboot I get through the boot screen to the console. I try to manually startx and I get the errors, "no device found," "no screens found." The second install I tried purging and blacklisting the nouveau drivers and entering safe mode. Then using apt-get install nvidia-current. After that, nvidia-xconfig. Same results.
The third attempt I re-installed and this time downloaded the drivers from the Nvidia site (version 256.53). Blacklisted nouveau, remove all nvidia, updated initramfs, etc. The install went fine however I still end up at a console after boot with the same messages as above. No device found, no screens found. I've tried searching through the forum and web and have tried things like adding the modset option along with many other hacks, tips and fixes. still, no go.I can live with the Intel graphics for now although I lose 512MB of memory. Unfortunately there is no way to disable or change this set-up in the BIOS. I've seen quite a few bug reports at Launchpad:
1. Is this something I should just wait til a fix comes? Will a fix come?
2. Is there, or will there be an official Updated Ubuntu Guide for Maverick to install NVIDIA drivers with this tecnology?
3. Lastly, is there anything else I should try??
View 9 Replies
View Related
Jul 3, 2010
I have tried a lot to get sound from my laptop Dell Studio XPS 16 having i7 CPU.
->uname -a
Linux Pakudidi 2.6.31-rc9-7-default #1 SMP 2009-09-08 18:49:15 +0200 x86_64 x86_64 x86_64 GNU/Linux
->
-> rpm -qa '*alsa*'
alsa-devel-1.0.21-1.1.x86_64
alsa-tools-devel-1.0.21-2.5.x86_64
[Code]....
Here, "enable_msi=1" was not initially included in sound.conf, I added. After adding I find that volume change buttons are working, but sound is not coming. Mixer channels are all set to active mode and vol is MAX to 100. Mixer channels show two tabs -- one showing HDA_Intel and the other showing HDA_ATI_HDMI. Mic Jack mode is Line_in.
View 5 Replies
View Related
Aug 7, 2010
Something about my sound setup does not agree with Linux. I couldn't get sound on Puppy Linux and I can't get sound with Ubuntu either. I'm trying to use speakers through the headphone jack at the front of the tower (system unit, whatever you call the thing that houses the motherboard/ CD Drive etc.)
I tried the basic sound troubleshooting from this guide: [URL]..Since I still have the links up from it, I might as well share them with you. 1. This is the ALSA Information Script tailored to my settings: [URL]..
2. This is the ALSA Driver Configuration Guide. Scroll down to Line 587 for my card ( Module snd-ens1371):[URL]..
3. This is just some general Hardware info:
[Code]...
View 9 Replies
View Related
Aug 17, 2010
Has anyone ever experienced an issue with a Creative Sound Blaster Live! Value Dell OEM sound card, models SB0200 and SB0203, using the EMU10K1X chip that causes any multimedia application (Amarok) or flash web site where the audio plays back way too fast?
I tried this on two different Dells, a Dimension 4600 and Dimension 8300. The only variable that was a constant was the Creative card. I took the OEM card out and put in another card, audio playback speed was fine. The only reason I am asking, even though the OEM card is slightly inferior, it has the front panel multimedia connector pins on the OEM card. Thus, if I use another card, either the front panel multimedia jacks become unusable or I have to turn on the integrated sound in the BIOS and run two sound cards.
View 1 Replies
View Related
Sep 11, 2010
My sound card isn't being found on F13, it's a VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60). I ran alsa-info and posted it to the following url:
[URL]
I've had these problems before intermittently and it was working until I rebooted recently. I've also attached my yum log if there was something updated that affected it.
View 1 Replies
View Related
Sep 27, 2010
When I run the openSUSE-11.3-GNOME-LiveCD-x86_64.iso from an usb stick and select "Installation" or "openSUSE Live (GNOME)" the screen goes to black after showing the load bar for a while.
This is most likely a graphics driver issue but I have no idea how to fix it.
This happens on a dell precision M4500. The same usb stick works fine on another machine.
View 3 Replies
View Related
Jul 31, 2010
I have tried many, many things to try to get the sound card recognized since upgrading from Mint 8 to Mint 9, and have still been unsuccessful...all modules and up to date and alsa was rebuilt this morning (to insure I didn't mess something up with my prior attempts to resolve). I have only been using Linux for about a month now, and really don't want to have to go back to Windows
Here is a link to my latest hardware and troubleshooting info:
http://forums.linuxmint.com/viewtopi...302076#p302076
Can someone on this forum please assist?
View 2 Replies
View Related
Jun 10, 2011
I am using debian on kernel 2.6.38-2-amd64 with Kde 4 and I have one sound card integrated on my mother board (Asus A8N32-Sli Deluxe) with Nvidia CK804.
Often when I start debian I get a message that sound card wasn't found, therefore from the Konsole I have to reload the as:
xxxx@debian:~$ sudo alsa reload
Unloading ALSA sound driver modules: snd-intel8x0 snd-ac97-codec snd-mpu401 snd-gina20 snd-pcm-oss snd-mixer-oss snd-mpu401-uart snd-pcm snd-seq-midi snd-seq-midi-event snd-rawmidi snd-seq snd-timer snd-seq-device snd-page-alloc.
[Code].....
View 2 Replies
View Related
Jan 7, 2011
I am running Slackware Linux-13.1. Recently I noticed that alsaconf has stopped working: when I run it all I get is:
Code:
However, sound works just as good as it did before I noticed the problem. The issue is present both with the generic kernel and with any custom compiled one.
Here is some diagnostics with the custom compiled 2.6.37:
Code:
Code:
View 5 Replies
View Related
May 10, 2010
I encounter many problems, the most pressing now is the lack of my Ubunto-PC to make use of my M-Audio Delta 1010 LT Soundcard. I installed ALSA package yesterday, but there's still no sign of my Soundcard to be found. sudo aplay -l delivers: aplay: device_list:223: keine Soundkarten gefunden ... (no soundcards found)
[Code].....
View 9 Replies
View Related
Dec 23, 2009
I am using a dell laptop which has Dell 1397 802.11B/G Wireless Mini Card. I not able to connect to internet and was not able to detect what actual problem is weather card is not supported (i.e. drivers are not available) .
Also, if any one can point to exact process to connect to wireless Lan using fedora12.
View 10 Replies
View Related
Jan 12, 2010
My Dell Vostro 1520's Dell Wireless 1397 WLAN Mini-Card must not have been set-up correctly, as the Network Manager won't even let me select the wireless tab. Please just explain to me, step by step, what exactly I must do to make it work! Additionally, I can't figure out how to disable my Touchpad's Tap to Click funtionality, which must be done if I'm to effectively use my current KDE installation of openSUSE
View 9 Replies
View Related
Mar 24, 2010
After installing an external sound card, Im having some weird issues. The cards chipset is fully supported by suse, (CM8738) so I dont think thats the problem. Besides, I'm getting sound, but not in some applications. The system's sounds work just fine (login, logout themes) amarok plays without any problems, kaffeine, mplayer they all work flawlessly, in fact I can see the difference in quality between the onboard sound and my new card. However, no web browser is able to play any sound at all, firefox, opera or chrome, nothing,zip. Plus, vlc cant reproduce sound either, nor can smplayer.
I've tried switching channels on and off(muting)in kmixer and in alsamixer, on the console, with no results. I disabled the onboard audio on the bios before installing the new card, however my ati video card has integrated sound, which I cant disable.... I used to get this exact same problem randomly with the onboard sound, but I just had to go to kmixer and turn up the "pcm" channel volume, which was set to 0, and I had sound again on my browser. However this card's pcm channel is at max and turning it up or down affects the whole systems volume, not just the browser's. Is it better to just reinstall the sound system, if so how could I do that.
View 7 Replies
View Related
Jul 28, 2009
I bought a Diamond Xtreme Sound 5.1 sound card because I had read online that this card was a good choice with Linux and came with universal driver software. I installed the hardware correctly (as it works with WinXP) but I'm not able to get it working with Ubuntu.
View 1 Replies
View Related
Mar 18, 2010
my computer after being updated a few months back lost its ability to make noise. the sound and volume settings see no input (i have an internal mic) or out put (speakers) hardware. they see no sound hardware at all. im running this on a sager so im assuming its an intel HDA audio thing. is there a package where i could report this bug?
running ubuntu 9.10 64 bit
View 3 Replies
View Related
Sep 5, 2011
I just bought a new graphics card and installed it. it works perfectly although my sound worked perfectly this morning and I think the graphics card is overriding my built in sound card. I need help fixing the sound. The graphics card I bought is an ATI Radeon Cedar HD 5450 The sound I want to use is HDA VIA VT82xx
when I run alsamixer I get Card:
HD-Audio Generic
Chip: ATI R6xx HDMI
[Code]....
View 3 Replies
View Related
Jan 3, 2010
I am unable to hear any sound at all using my M-audio delta 44 soundcard (which works fine in Windows - Dual boot).how I can get this working?
View 4 Replies
View Related
Dec 20, 2010
I have been using Ubuntu as my main OS on my desktops for a couple of years now. Started off with a HP with a Creative Labs XiFi soundcard, but am now using a Dell with a Creative Labs Audigy. Sound worked perfectly on the Dell since a clean install (about 7 months ago). I turned it on a week or so ago, and no sound! Even the little sound indicator in the notification area has gone.
View 8 Replies
View Related
Mar 7, 2010
I installed Mangler and one of its requirements was pulse-audio. I installed pulse-audio everything worked great except i couldn't get sound out of wow if i started mangler first and vice-versa. I then found a version of Mangler that worked with alsa. So i uninstalled mangler and pulse-audio, installed mangler-alsa. Everything works great now. The problem is when i uninstalled Pulse-audio i lost all my sliders in Yast > Hardware > Sound > other > volume. The only thing that shows up is master volume > Test. My sound works great just can't adjust anything. How do i get my sliders back. I would like some advice before i screw something up. (lol) My Sound card is according to sound configuration SBx00 Azalia(Intel HDA) - Driver snd-hda-intel.Opensuse 11.2 KDE 4.3.5
View 2 Replies
View Related
Jun 14, 2011
I have suse 11.4 installed and I wish to replace the on-board sound chip with an add-on sound card. The following are available at my local shop but they cannot advise whether any will work on Linux Suse 11.4.
Anyone know which of these cards will work on Suse 11.4?
Sound Blaster X-Fi Titanium HD
Sound Blaster X-Fi Xtreme Audio
Asus Xonar DS
View 9 Replies
View Related
Aug 17, 2010
sound card is working well inside SuSE and everything is ok there. But when I install Windows 7 or XP inside Xen Virtualization software, I can't use sound card and Windows is unable to find any sound hardware.
View 1 Replies
View Related
Aug 9, 2011
I am setting up a mythtv/xmbc box on Ubuntu 10.10 (natty does not install on my hardware). I have a Sabrent TV PCIRC tuner card, which seems to work fine with the proper card and tuner settings. My on-board sound is HDA-Intel surround sound, which I have configured as analog duplex.
Currently the sound works fine through my speakers plugged into any jack on the back of the PC (two speakers, one jack). I can watch ripped movies and listen to music. The TV tuner is pumping sound from its external jack -- if I hook it up directly to the speakers it works fine. I can feed the Tuner's sound to the line-in on my motherboard, but nothing comes out. In the sound manager, i have the input device selected and the input level shows that the sound is coming in through the connector, and I can test the speakers and they work fine, but they don't seem to be communicating that the sound coming in needs to be pumped out through the speakers.
View 2 Replies
View Related
