My reinstalled OS Linux Lite ( version 1.0.9.E) connects fine with cable but Broadband BT hub does not support the protocol for wireless.Is there a Linux download which will solve this?
View 7 RepliesWife's laptop has AR5001 Wireless Adapter laptop model is Toshiba Satellite A215
Problem : Wireless networking randomly loses connectivity and can not regain connectivity, the only apparent solution is a full power down , this is not even certain to work. The card works under Windows, she hates Windows. (I love her for this) I know it's not faulty hardware , because it will work for days on end under Windows without problems.
Things I've tried : madwifi drivers (any and all versions available) : These increase stability of the signal and seem to delay the inevitable however it still happens. When using these drivers the only option is to unload them modprobe -r then reboot then remove them again and re add them. It makes no sense why this works, and if I don't remove them prior to rebooting it will not work.
ATH5K drivers : These are pretty much junk, results are unpredictable at best, sometimes it will work perfectly for a few hours, sometimes it will not work at all. Nothing is repeatable, I can't seem to force whatever condition is causing this. rfkill does not show the wifi being blocked (hard or soft), unblocking it anyway does nothing, only way to make this work and it's iffy is to fully power down wait 5-10 minutes turn it back on and it MAY decide to work.
Firmware update : Updated the Toshiba BIOS to the latest version of the firmware 2.0 no joy here either. Same issue both sets of drivers.
Tried different distros and kernels : I've tried Mint 9, 10 ,11 ; Ubuntu 10.10, 10.04 , 9.10 and 11.04 (which is currently installed) , Fedora and OpenSUSE. All are giving the same problems. I have also tried a slew of different kernels no joy from any of them (I'm not at the computer with the issue now I will post exactly what kernel versions I've used when I have access to the machine).
Another useful bit of information, the hard switch to disable/enable wifi WILL disable it but turning it back on does absolutely nothing. The hotkey does nothing at all. The bios does not have an option to disable or enable the wireless card.
I will also post the typical lsmod , lspci , iwconfig all that good stuff when I get back to the computer in question. I'm probably just going to buy a PC card for it and give up on that one, but this is driving me insane and I would really like to see it resolved even if I do replace the hardware.
I recently installed Ubuntu on my MacBook and it's great. The only problem is the Internet speed... on Mac OS X it is much faster which doesn't surprise me because both have been optimized to run fast.
I was wondering if there was a driver, or similar, that would improve the speed for Ubuntu?
I got ubuntu working fine on my netbook and wanted to play around with opensuse. I have it installed and everything works fine except my wireless connection. I have updated everything since the installation through a wired connection, that didn't help. I have read the stickies, but to be honest, I'm so new to this stuff I'm kinda lost. So my wireless network has a WEP encryption and I have entered that password as a 64 HEX Key in the Wireless Manager widget. It connects to the network and says is labeled as active, however there is still the yellow exclamation shield next to the connection. Firefox and other apps don't have access to the internet.
View 9 Replies View RelatedAs promised the finished (pretty much finished) wireless script can be downloaded here the wireless_script is a diagnostic tool for wireless issues. It will return all relevant information to help diagnose a wireless connectivity problem, return connectivity stats and attempt to fix common problems such as blocks. It comes in cli - wireless_script_1.2.sh or gui - wireless_script_zenity_1.2.sh'
Let me know any issues you have with it. My contact details are in the readme.txt (also the wireless results.txt generated by running the script includes code tags for forums - so please copy and paste the whole document when pasting on forums to enable this function)
I have an older Gateway with model number: 4024GZ, and I just installed Ubuntu on it and I am not able to connect to my home's wireless network. I am assuming that this is because of a driver issue, whether there is none or the old driver isn't compatible. So is there a website that I can go to to maybe find a driver that will work with both my wireless card and ubuntu? My wirless network adapter is internal and is a Broadcomm I believe. (btw I am a beginner here and if I have posted this in the wrong section,
View 6 Replies View RelatedMay I please have some help configuring wireless connectivity?I just moved and went from connecting to a LAN infrastructure to connecting with a wireless cable modem. The modem is dual-purpose, it has two ports, one for an Ethernet cable, and an access point for a wireless connection. The ISP is CableOne. My laptop, which I use most often, is wireless capable, and I want to use the wireless feature. The laptop is running Fedora 13 KDE, with a VirtualBox virtual drive running WinXP.
I have used NetworkManager to create a wireless connection and name it. I have also used WPA encryption for this because I don't want anybody else using my bandwidth. Moreover, I have tried no encryption and WEP, all to no avail.
I have bought a new Insipirion 1464.Installed a OpenSuse 11.0 ,Gnome Desktop .
I dont have wireless connectivity in my laptop(i hve never used Wireless ).
I have done following step
1)Checked for wireless card in Hardware Information ==> was present Wireless 1397 wlan min-card from broadcom family
2)Checked for firmware dmesg|grep firmware ==>no output
3)Then checked for access points
PHP Code:
I've been trying to use the wireless adapter that came shipped with my computer for a while now (it is NOT a USB adapter; it seems built into the computer). However, I can't seem to get it working.HP says that the driver is Lite-On USB Wireless 802.11 b/g Adaptor. I am currently connecting to the internet with my netgear USB adapter (I think the driver is something like prism_usb)
View 3 Replies View RelatedI am new to linux. I just installed linux on my PC and wanted to configure wireless network connections. I have entered SSID and mode is set to infrastructure. I don't know what is BSSID do I need to enter MAC address (of router?)?I need to connect to internet wireless can you please guide me ?
View 1 Replies View RelatedI have a Air-CB21AG-A-k9 cisco Card and trying to run it with Ubuntu 11.04. But this card doesnt seems to be plug n play device with ubuntu 11.04. As soon I inserted the card both the leds are flickering but no wireless conectivity.
View 9 Replies View RelatedThe problem is I have a wireless Belkin router which I can connect to, but after being connected for a few minutes the net disappears (cuts from the router) and my laptop will have to reconnect again to the router for internet to work again. After a few minutes (or seconds in some cases) the connectivity loss will happen again over an over.
How to fix this problem or some things I can try, I've tried updating to two different firmwares, two different channels and resetting the router. The biggest problem I find is that this happens on both my laptop, another laptop in the house and also my tablet PC but doesn't happen on two other laptops in the house, I've also tested with windows 7 and Ubuntu with my laptop.
My laptop wireless card is Atheros AR9285 802.11b/g/n WiFi Adapter
I'm running Lucid Alpha 1. Installed it about two weeks ago. Until a few days ago, the wireless networking was the best I've witnessed on any o.s. However, after last Wednesday's updates, connectivity now lags about 10-30 seconds whenever I open any web-page or access the repositories via aptitude. Granted after it gets going, it's fine. I noticed this same behavior in 9.10. I tested my XP connection and found no problems. .
View 3 Replies View RelatedI recently formatted an old Dell D600 and installed 9.10 on a single partition. It connects to my Airport just fine hardwired, but I have had no success getting the IntelPro/Wireless 2200BG card to talk wireless. I've entered the SSID and WPA2 security ID with no success.
View 2 Replies View RelatedI just installed Ubuntu 10.10. I was using iBall N 150M USB adapter for internet connection with Windows XP. Let me explain about the present Windows connection :
I am using an Outdoor CPE Wimax. For mobility purpose I have connected this wimax to one LAN port of ADSL+ WiFi router ( Beetel 450 TC1 ). This ADSL+wifi router reset to Factosy settings and enabled DHCP. With this setting , I am perfectly able to connect my laptop to Internet.
When I connect my USB adapter to Ubuntu , intially it detected the signal and asked for credentials. I gave the same and network established. But I am not able to browse the net. If I give [URL]..., its going to the ADSL+Wifi's diagnosis page. With Windows , [URL]... was going to the Wimax modem. After 2-3 trial and error , now Ubuntu also not able to connect to the wifi network.
Just recently I've been having strange connectivity problems with my wireless network. The connection has previously worked fine and haven't had any problems with it. I haven't installed anything that would have affect it as far as I know. how do I go about testing the network to see where the problem lies? I'm running Ubuntu 10.10 with a Netgear WG111v2 wireless adapter and my guess is it is some strange configuration problem or a rogue application is eating up packets because the system works fine when I boot it up into Windows.
When I try to ping my router I'll usually get something like 98% packet loss. However in the output below, the network sprang to life half way through my pings so it went up to 63%. What other tools can I try to find out what's going on?
Code:
alex@obsidian:~/dev $ ifconfig
eth0 Link encap:Ethernet HWaddr 00:1a:4d:4e:03:3f
UP BROADCAST MULTICAST MTU:1500 Metric:1
[code]....
I'm having making network/internet connection with my laptop. I have:Toshiba 1415 S173laptop
NetGear WG511T pcmcia card using madwifiNetGear WPNT511 pcmcia card using windows driver via ndiswrapperSlackware 12.2In both cases the card is recognized, and I can get a list of access points with iwlist.I can set the card to connect to the desired access point. I can use dhclient to get an ip address from the remote dhcp server. This works, the card is assigned a valid ip address on the desired network.Once I do this, however, I cannot access any network resources, no Internet, and no other devices on the network can see, ping, or access my laptop. It does this with with both cards, using madwifi or the windows driver via ndiswrapper.
I have just upgraded to 10.04 and can't get wireless connectivity because the STA driver for bcm4312 fails to activate. Does this sound familiar to anyone? I had had similar problems in 9.10 and tried to install bcmwl-kernel-source which apparently caused errors in the upgrade process. Not sure if this is part of the problem.
View 5 Replies View RelatedI have a Toshiba Satellite L305-SP6944C, Pentium Dual Core 2.16, 2GB RAM, 160GB hard drive, DVD-RAM UJ880AS, display 15.6 TFT widescreen, ethernet Realtek RTL8101E/RTL8102E PCI Express, WLAN Realtek RLT8187, Opensuse 11.2 and KDE 4.3.1. Installation was OK and finally the wireless card is working... but I don't have conectivity bacause in the browser (Firefox) appears a message saying "the server can't be found"
I follow the howto write by Swerdna. With ndiswrapper I install the XP driver for RLT8187, KnetworkManager is in charge of connections showing both eth0 and wlan0, the wireless sign of router Dlink DIR-280 is OK, in the dialog box of network connection I put the mac address of the wlan card but I think that is not the problem.
Other thing that I missed is that I don't find boot.ini at any directory to add modprobe ndiswrapper in the boot sequence, in etc/init.d/ appears a "boot" file, is this file that I have to change to modprobe ndiswrapper??
I would like to share my internet connectivity on eth0 with another computer on eth1.
+-----------+ +-----------+ +-----------+
| | | | | |
|ADSL Router|-------------| Computer |-------------|NFS Client |
| | eth0| |eth1 | |
| | dhcp| |static | |
+-----------+ +-----------+ +-----------+
How can i maintain this network topology and allow internet connectivity with dns across my main computer?
I read that "ATDT*99#" is used to create a GPRS connection through a GSM/GPRS modem how exactly this AT command works.
View 4 Replies View RelatedI'm using Linux Mandrake 9.0 on my Dell 750MHz laptop. Linux is not making a dial-up connection, but modem test showed passed. Is there any utility to fix this problem. I have to often use dial-up connection.
View 1 Replies View RelatedI have a Toshiba Satellite L55 S5105 Laptop with "Atheros AR8152 PCI-E fast ethernet controller"
and "Realtek RT8188CE Wireless LAN 802.11n PCI-E "
I have ubuntu9.10 running on this[dual boot].
For some reason there is no wifi and ethernet connectivity.
Are the drivers not installed? where and how do I start to troubleshoot this problem.
I have comma separated file containing 3 fields:
Name,Shortcode,URL
Example of file is
Sony,52525,http://17.0.0.1/xyz
NDTV,53636,http://10.0.0.1/abc
Now i want to test every URL connectivity from my server by executing it using shell script and if url gives back response it shows output as "OK" in green color and if url is not responding it shows "NOT CONNECTED" in red color.
Output will be like following:
Sony 52525 OK
NDTV 53636 NOT CONNECTED
I'm learning via baptism by fire method here, and need to test PHP connectivity to a local postgresql 8.3.9 setup. (CentOS 5.5 x86_64). I have got PHP and Postgres both working; I can pull up a test PHP page via web browser, and I can login to postgres via the command line. What I can't figure out is how to test PHP connectivity to the local DB.
I found this test script:
Code:
<?php
$conn = pg_connect ('dbname=template1');
?>
Which I've named, testdb.php - when I run ./testdb.php from the CLI though, I get:
Code:
./testdb.php: line 2: ?php: No such file or directory
./testdb.php: line 3: syntax error near unexpected token '"dbname=template1"'
./testdb.php: line 3: `$database=pg_connect ("dbname=template1");'
I've seen a LOT of pages describing the internal code of the PHP file, but as a newb to this, I don't know how to execute this test. I've ran chmod 755 against the file to verify permissions, but this didnt effect the results. I've also done a "chmod +x testdb.php"
Code:
PHP 5.1.6 (cli) (built: Mar 31 2010 02:39:17)
I realized I wasn't doing this:
Code:
php testdb.php
but when I do, I get this error message now:
"PHP Fatal error: Call to undefined function pg_connect() in /var/www/html/testdb.php on line 3"
Our laptop all of a sudden will not connect with our usual wifi network connection which has disappeared & now mysteriously shows dd-wrt . It shows an internet connection has been establihed with dd-wrt but does not work.
View 1 Replies View RelatedI have installed open suse linux 11.3. I have mysql database and jdk 1.6.20.0. How do I connect from java to mysql database?
View 2 Replies View Relatedred hat 5 update 4 64bit. on an interactive boot i can ping -t my vm linux server from my physical MS XP workstation and a vm W2000 64 bit server until xend is started, after that i get destination unreachable. if i choose not to start xend on the interactive boot i retain connectivity. i have read some blogs that imply this might be a bug - is this so? do I need xend on my vm red hat box that is a database server?
View 1 Replies View RelatedJust installed Ubuntu 10.10 on dual boot computer. Each OS is on separate hard drive with GNOME selection between Ubuntu and Windows 7 Ultimate. Firefox was working fine yesterday when I went to use today, nothing. Email through Thunderbird is down as well.
View 3 Replies View RelatedCamangi WebStation (android pen tablet)
Incredibly poor Wifi connectivity (No WPA, not even WEP full support), missing ether plug. Easy to freeze. Poor input method. Considerable pricing. poor applications. (not android-market compatible) not well organized web pages.
My impression: You have a right to buy. It is up to you, if you want to. It is your responsibility.