Anyone knows how to configure wpa_supplicant.conf for ad hoc mode using wpa/wpa2 encryption...Is wpa_supplicant will work wpa/wpa2 encryption? I tried many ways but i am not able to configure for adhoc mode in wpa_supplicant using wpa/wpa2
View 2 RepliesI was using Fedora 14 for some months and my wireless was working fine. I've set up a hidden network with WPA2 Personal authentication. My laptop has an Atheros AR2413 802.11bg NIC and my modem/router is a Topcom Webracer. Yesterday I upgraded to Fedora 15 and I can't login to that network now. The only way to login again is to boot with the old Fedora 14 kernel that still shows up in my grub menu.I've searched this on these forums there are plenty of people with the same problem but the only suggestions are that the network card isn't supported by Fedora or the network card doesn't support 802.11bg.some suggest changing the authentication method in the router... and the only one who got it solved was by rebooting the router... None of this addresses the fact that the same hardware/network was working just fine in Fedora 14. And I still can't find a way to have a wireless WPA2 connection with Fedora 15.What can I do to fix it?
View 6 Replies View RelatedFirst, I've dinked around with Linux b4 but never really considered it for an everyday desktop machine. After installing the ubuntu 10 release I have to say I am really impressed. This is going to be the kids homework machine!I had one challenge during the installation and that was getting wireless networking going. I set up Win XP first (to get the ndis driver and validate connectivity).After installing ubuntu I could not get the adapter (Netgear N300/USB) to connect to our router (D-Link DIR-825) using WPA2 and AES. Finally I got it to work after setting the router to only TKIP encryption. This works ok but causes the adapter to operate at a lower connection speed
View 3 Replies View RelatedI wanted to run a little media server in my house, shared with my laptop only, so I could free up space on my laptop drive. I took one of my Linux boxes out of my render farm and loaded up a minimal install, command line only of Ubuntu Lucid from the mini ISO (32 bit). I had to plug in a lan cable to install, but I wanted to move my box back out to the "farm" that doesn't have wired access to my intranet.
After much research, trial and error, this is what worked for me. My wireless card uses an Atheros AR5001X+ chip, and it works with the desktop cd out of the box. I found the "just works" desktop install uses the ath5k driver that is now included in Lucid, but I'm not using a desktop or window manager. I haven't tried this on server version, if you do, let others know what you had to install to get it to work.
The things I do tell you about, I instruct you as if you are a newbie, however I have left out some things that users should know or be able to lookup easily, like if you want a static address instead of using dhcp. You may not need all of the steps or you may have to do more research and troubleshooting.
Find your wireless card (you may need to lookup what to do if it is not recognized at all)List all pci devices, only show network devices (-v verbose, -vv very verbose): >>lspci -vv | grep Network List all hardware (| less lets you pause at each page - arrow keys, page down/up to navigate, q to quit) >>lshw | less
[Code]...
Below is a print out of my partition Table from Fdisk, in Cylinder mode, Sector mode, and then in expert mode?
Why in expert mode does it look like Partitions 2 and 3 share the same sector / hd / Cylinders? Is this OK?
Code:
I am an emacs user, and I noticed that on my new machine (running F15, 64bit) flyspell-mode will not work in tex mode.
I get errors that look something like this:
Code:
Spell-checking inequality-model.tex using hunspell with default dictionary...
Spell-checking region using hunspell with default dictionary...done
ispell-send-string: Process ispell not running
When done with a buffer, type C-x #
code....
I've got a Toshiba Satellite L25-S199, and it includes an Atheros wireless NIC based on the AR2413 chipset, I believe. Currently I'm running OpenSUSE 11.4 on it, but I've previously had Xubuntu and Ubuntu, and this problem has always existed with WPA2.
Specifically, the LAN is a wireless WPA2 with AES encryption (no TKIP). The computer can connect to the network just fine, but the web is all but unusable; it is very finicky, mostly failing to fetch any pages, but sometimes succeeding (mostly with Google pages, and those from the local network's servers). Perhaps a DNS issue?
This problem doesn't occur with WEP or no encryption.
Here's the output of lspci
09:04.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
And the relevant output of hwinfo
22: PCI 904.0: 0282 WLAN controller
[Created at pci.318]
Unique ID: y9sn.SufKn0XT2bB
Parent ID: qscc.hTSZxA6Z5F6
[Code]....
Any wpc54g wireless adapter be converted to version 7.1 or 7.2 which should be wpa2 compatible?
View 1 Replies View RelatedI'm trying to connect to a new router that has WPA2-PSK encryption.In the connection window Ubuntu presents when choosing the network from the wifi menu, there are only the 3 WEP options (40/128 bits, 128 bits, and dynamic) plus LEAP. But no WPA2-PSK or any other WPA..I know for sure my router is set to WPA2-PSK and not to WEP.
View 1 Replies View RelatedI am planning to create a home router using my Linux laptop. Is it possible to secure the wireless router with WPA2, and how would I set that up?
View 2 Replies View RelatedI've been receiving a LOT of log cruft ever since I installed my WUSB100V2 (using the rt2870sta community driver from the Linux kernel) and was wondering what it all meant.
Many times when these messages occur it is accompanied by slow network speeds and many DNS queries and outgoing SYNs being dropped. I have searched for documentation for these (error?) messages and have come up empty as far as what they mean or how I can stop them from occurring.
I reside on the opposite side of the building from my WAP. I have taken steps to improve the signal strength, but the signal quality hovers between 50% and 70%, sometimes dropping to 40% for unknown reasons.
My /var/log/messages:
Sep 12 05:04:40 necronomicon -- MARK --
Sep 12 05:29:48 necronomicon kernel: 0:3 LTL=0 , TL=0 L:4284
Sep 12 05:29:53 necronomicon kernel: 0:3 LTL=0 , TL=0 L:4104
Sep 12 05:30:06 necronomicon kernel: 0:3 LTL=0 , TL=0 L:4156
[code]....
I'm relatively new to Linux.My netbook ran updates yesterday for Ubuntu and now I am unable to reconnect to wireless network connection.I am using WPA2 encrypted security.I am able to connect via wired LAN. Also, when I went to connect using USB mobile connection, I get an error "unable to mount location". I get the same error if I try to connect my external CD drive. I have tried to force mount but no luck.
View 17 Replies View RelatedThe university I go to uses a WPA2 wireless network that requires a netID and password to connect too. I installed wicd but I can't seem to connect to this network, is there a way to add this functionality to wicd, and if so, how do I do that (links to a how-to or guide would be nice, I've yet to find one).
Also, I spend most of my time on campus in the command line, so I'd like to know if there is a way to use command line utilities to connect to this network (again, a guide or how-to would be nice)
I can get online through my fedora live USB just fine (w/ network manager) but I'd rather get on directly from slackware.
My linux workstation recently crashed. After rebooting, Linux (Red Hat 5.3) will not boot properly and automatically went into emergency mode or recovery mode i think. I can still see my /home/user/ and all the files inside.I boot from CD to rescue mode and tried mounting read-only the /dev/sd5 which contains the files in the crashed hard disk to try to copy out my files but mounting was unsuccessful (invalid argument). I checked the filesystem type using fsck -N /dev/sda5 and shows it to ext2. i tried to mount another known working hdd and was successful.
My question is why in emergency mode, the crashed hdd is able to be mounted automatically as read-only but cannot be done in rescue mode thru a bootable CD?Is there any special mount options used in emergency mode?I also cannot copy out in emergency mode booting from the crashed hard disk as everything is read only.
It seems like everything is configured correctly but NTP will start, sync once or twice in the first hour, then never sync again.. Below are signif lines from my /etc/ntp.conf files.
Server:
----------
tos orphan 9
server BOGUS_1 # Must operate in orphan mode
server BOGUS_2
[Code].....
I can't get n-mode working on my 5100AGN. I tried
Quote:
iwconfig wlan0 modu 11n
but it doesn't work.
iwlist modu gives me this:
Quote:
wlan0 unknown modulation information.
I really need n mode for 150 Mbps and greater range provided by N-mode for my UGV (unmanned ground vehicle) project.
Using the Nvidia driver from the repo on a Geforce 6800gs. In Kde4 all 3d applications seem to be working properly so I don't know why Gnome 3 is doing that myself. It wasn't working at all at one point and I am assuming that some update or another got it going. Perhaps a repo switch. Unfortunately I am not sure of what those changes may be. I just know that it does run now but only in fallback.
View 6 Replies View RelatedI recently uninstalled some unnecessary libs thinking that I could work around without them. It turned out I couldn't. So I installed every single one, and it seemed like everything was working fine. But then I tried to boot, and was thrown into a low-graphics. Well I tried to boot in a low-graphics environment temporarily but it turned out X just restarted. Then I tried to reconfigure the settings, but choosing any option it threw me back into the last menu without any action being taken.
So I googled up some lines it was vomiting at me and it indeed might be my xorg not configured properly. but every time I try to reconfigure it and I look into the .conf file it turns out it is completely blank. maybe I should also note I am sporting a 64 bit bubuntu, not an NVidia though, Intel Series 4 express chipset family thing. I think it is a GMA4500MHD but not sure, what shall I do so that I don't have to reinstall my beautiful pimped out system?
as Ubuntu is my only OS on this box.I had this PC running as a server for a few months with few reboots.I installed updates as usual yesterday, and hadn't changed anything configuration-wise since the last reboot. Well last night this server that I was running was moved to another Windows box and so I finally got to shut this PC down for the night. In the morning, I was greeted with an endless splash screen. It went on for 20 minutes without anything. I did update the kernel through update manager.
So what do I do? This machine has a 1TB HDD with a lot of very important data on it--reformatting is not a considerable option at this point. Which is bad because I don't know what else I could so when even recovery mode isn't working...
It seems like everything is configured correctly but NTP will start, sync once, then never sync again.... Below are key lines from my /etc/ntp.conf files.
Server:
----------
tos orphan 9
server BOGUS_1 # Must operate in orphan mode
server BOGUS_2
[Code]....
I had let it run over the weekend. It did not update so it is not just this one time. It never syncs again.
I've a problem booting on my fc14 64 bit. I install it yesterday and everything was ok. Then I updated it and I installed wireless drivers kmod-wl equivalent to my kernel version that is 2.6.35.6-45. I've a pavilion dv6 with a broadcom ach. for networking. So the next step was installing kmod-nvidia for my nvidia geforce but after rebooting my never allow me to log in! I can se the tipical blue-white progress bar loading nvidia drivers but not else!
my screen freeze itself after the progress bar became white. I would resolve by rescue mode but I've installed fc14 64 b using a usb-pen drive and I find no way to do this from live version.
I have ubuntu 10.04 installed. I have a problem when my usb IR receiver is connected, than suspend mode isn't working. System will jump into black screen and that's all. Only hard reset works. I tested this problem also on ubuntu 9.04 and situation is the same.Is there any way how to force suspend mode without "looking" on this device? Do you need any log file to trace reason of this problem ?
View 2 Replies View RelatedWhatever settings I use in the power manager, (Ubuntu default Gnome Power Manager) nothing appears to change. Screen brightness does not change when moving the slider, but is reduced after 5 or 10 minutes (haven't timed it. Probably whatever is default) of inactivity, even though the reduce screen brightness checkbox is unchecked. The latter is pretty annoying when watching online TV streams, especially since the video also exits full screen mode when the screen brightness is reduced.
The weird thing is, as the title implies, that when booting in recovery mode with FailsafeX the power settings seems to work. At least the screen brightness varies as the slider is moved I should probably mention that it is possible even in normal mode to adjust the screen brightness by using the buttons for adjusting screen brightness on my laptop (Fn + arrow up/down)
I have installed ubuntu 11.04 just yesterday and have installed the necessary nvidia graphic drivers too. But when I maximize any application(be it chrome, firefox, vlc, media player), the whole screen becomes white and when I escape from it to make it of small window, it again runs normally. Sometimes it work fine, but most of the times it is like what I told above. Please tell me some solution or I will have to go back to windows.
View 5 Replies View RelatedDoes anyone else have the problem with Natty 64 bit, where when apps are opened up in full screen its not filling the screen properly, until the app in minimized & maximized again? Unity works fine, this is only an issue in classic mode.
View 4 Replies View RelatedBAM your ftp doesn't work. Out of the blue my ftp connections stall when I ask for a directory listing. I am using ncftp as I have for several years. And after a long pause I get the answer:Data connection timed out.Falling back to PORT instead of PASV mode.I then get the listing and the connection continues in PORT mode. But not with FileZilla it just hangs. Also bit torrent no longer works. Set up is a home network of 6 machines reaching the internet through a linux firewall box, qwest DSL modem gt-701-gw. Nothing has changed but sometime in the last week something has changed because now FTP PASV and BIT TORRENT can no longer connect.
I am holding back from completely rewritting the iptables/shorewall rules and have spent the day with the website host 1 and 1 and Qwest. Trying to find a solution. This problem is universal, all machines (windoze and linux) and all software (coffeecup, ncftp, ftp, filezilla, bit torrent).
I'm using gnome shell 3.4.2.1 from the stable debian repository. 2 problems with the gnome-tweak-tool:
1) The extensions list is empty, even when the gnome-shell-extensions package is installed
2) in the non-classic mode only, setting made in the tool have no effect: e.g. Shell->Show date in clock does not toggle the date in the clock.
[URL]
I forgot my new password. I followed the guide on how to recover the password but in recovery mode my keyboard doesn't work, I have tried a usb and a ps2 keyboard. What is going on? Or is there another way to reset my password?
View 4 Replies View RelatedI'm currently trying to setup a minimal Slackware installation. Everything is well, except for screen brightness/hard disk control via laptop-mode-tools. I was wondering if anyone used it, and if they got it to work on their Slack systems, how they went about doing it.
View 5 Replies View RelatedI tried to make Compiz work using the experimental 3D support of the free Nvidia driver, because I am suffering from a bug in the proprietary driver (click here for launchpad entry). The free driver I mean is the one that shows up as "Experimental 3D support for NVIDIA cards" in the "Additional Drivers" manager (note: for some reason, this option will only present itself when no proprietary driver is currently active).
Now the strange thing is: the driver does not provide 3d support, and behaves generally awful (lots of glitches and so on) when I boot my system normally. But when instead I boot from the grub menu into recovery mode, then select "failsafe graphics", and then select "restart X", the whole thing works perfectly! So now I am running the experimental 3d driver, I have compositing working, 3d animations on docky. Somehow, the failsafe boot sequence does something right that my normal boot sequence does not. When I reboot in normal mode, everything is screwed up again.
I have no idea what statistics about my system I should include here, because I really have no idea what could possibly be wrong. I am running 32bits Natty in Classic mode, on an Ahtlon Dual Core 4850e machine, with a GeForce 6150 LE graphics card. These are the normal and recovery entries in my grub.cfg:
Code:
menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os {
recordfail
set gfxpayload=$linux_gfx_mode
insmod part_msdos
[code]....