In vmware workstation 6/7 (using windows xp as host), how can I map virtual disk of my linux VM? When I try to map it, it maps but when I try to explore it, it gives me an error of formatting!
View 2 RepliesI tried to format my harddisk (160 GB) with the following command
dd if=/dev/zero of=/dev/sda
After some 3 hours, following error came up:
dd: writing to '/dev/sda' : No space left on device
312581809+0 records in
312581808+0 records out
160041885696 bytes (160 GB) copied, 10708.3 s, 14.9 MB/s
I installed win 7 and Linux Mint, however I've now decided to uninstall both and start with a fresh hdd. Anyway formatting went fine and started installing win 7 however there was a reading error from cd and canceled. Now ever time I try and start my pc it comes up with error: unknown filesystem and the grub rescue prompt. Now I don't know what to do as i can't seem to get around this and back to win 7 installer.
View 1 Replies View RelatedSo I installed Wubi with Ubuntu 10.04 and chose the standard partition size (8GB?) and now I am running out of disc space. How do I resize this partition?
This guide didn't help: [url]
How do I resize the virtual disks? The download link doesn't work and LVPM doesn't support 10.04.
Any other options or do I need to re-install the whole Wubi?
I have a Dell Studio XPS running openSUSE 11.2 with dual mirrored disks (using Dell's SATA controller). Does anyone know how I can set up automatic monitoring of the disks so that I will be informed if either fail? I think smartd might be what I need here. Is that correct? I added:
/dev/sda -a -d sat -m <my email>
/dev/sda -a -d sat -m <my email>
smartd is running, but how do I know that it will report what I need? I also have a client with a Dell PowderEdge SC440 with SAS 5/iR also running openSUSE 11.2. They also require automatic monitoring. There doesn't seem to be a SAS directive for smartd. I notice that the newer release says it does support SAS disk. I upgraded to 5.39. On restart (with DEVICESCAN as the directive) I get the following in /var/log/messages for my SAS RAID disk.
Sep 18 10:47:26 harmony-server smartd[25234]: Device: /dev/sdb, Bad IEC (SMART) mode page, err=4, skip device
I ran:
smartctl -a /dev/sdb
and got the result:
smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (openSUSE RPM)
Copyright (C) 2002-10 by Bruce Allen, smartmontools
Device: Dell VIRTUAL DISK Version: 1028
Device type: disk
Local Time is: Sat Sep 18 11:32:08 2010 JST
Device does not support SMART
Error Counter logging not supported
Device does not support Self Test logging
Is there some other tool/package that does support DELL virtual disks?
Just installed debian linux. I did the smallest install possible because I didn't really know what I was doing. I have the linux style cmd prompt on the screen. I want a windows style gui - with text editor and other windows for copying and pasting. How do I get that on my linux version ?
View 14 Replies View RelatedI'm having problem in formatting the newly added hard drive to my Ubuntu 64 bit server, is there any explanation why I got stuck to this error ?
Code:
root@isuzu:~# fdisk -l
Disk /dev/sda: 21.5 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[Code].....
I'm trying to format an external hard disk under Ubuntu 10.04. All starts well, but eventually I get the message:
Error formatting volume
Error creating file system: helper exited with exit code 1:
Error calling fsync(2) on /dev/sdb1: Input/output error
I installed Sun's virtual box 3.1 under Ubuntu 9.04. It worked flawlessly. I upgraded to to 9.10 and know I get a kernel error. rc=-1908 Now I cannot get Windows to load.
View 2 Replies View RelatedI have new external usb drive which I'm trying to format to NTFS so I can also use in in windows. I've set it up using fdisk
Disk /dev/sdd: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x604a2a7d
Device Boot Start End Blocks Id System
/dev/sdd1 1 60801 488384001 7 HPFS/NTFS
And tried formatting using
mkfs -t ntfs /dev/sdd1
However I get the following error
Cluster size has been automatically set to 4096 bytes.
Initializing device with zeroes: 100% - Done.
Creating NTFS volume structures.
Error writing to /dev/sdd1: Input/output error.
Error writing non-resident attribute value.
add_attr_sd failed: Input/output error
Couldn't create root directory: Input/output error
i have a dell server. its a couple of years old and has a perc 4 raid controller in it. When i do an install it shows the drives configured in the raid 5 configuration. i select the disk and do an auto partition. It goes for about 10min then errors with "error formatting drive volgoup00 the error is serious occurred press enter to reboot" or something like that can remember all the words. It doesn't give any info about the error.
i get the same error on centOs 5.5 and Ubuntu server 10.10
There is a firmware update for the raid controller that i could apply but dell's site was not letting me download it yesterday. Other than that I am not sure what to do. I could try an older version of CentOS 5.4 but i figure someone might tell me how to fix this so i can run the newest version.
I am facing a problem while installing backtrack 4.0 on my virtual box. After assigning a hard drive and booting from the live cd, i am receiving a error message as follows:
Loading, please wait...
Buffer I/O error on device hdc, logical block 76636
(this statement gets repeated like four times with different logical block id.
SQUASHFS error: squashfs_read_data failed to read block 0x5bb337b9
SQUASHFS error: unable to read is index table.
It is not the first time i install operating systems on virtual box though it is the first time i receive such an error with backtrack.
I setup a virtual server with these configurations:
1. Mail server: POSTFIX / DOVECOT
2. Webmin / Virtualmin
I am getting email to desired folders locally but I am not getting email from outside to desired users. Emails are bounced back with message "Address not found in virtual alias table".
Recent log errors are:
Sep 8 04:25:49 server1 postfix/smtpd[28002]: cannot load Certificate Authority data
Sep 8 04:25:49 server1 postfix/smtpd[28002]: warning: TLS library problem: 28002:error:02001002:system library:fopen:No such file or directory:bss_file.c:122:fopen('/etc/pki/postfix/root.crt','r'):
[code].....
I tried creating a virtual server in apache and it got created successfully. (I also added a zone in dns for that domain successfully) However, when I try opening that domain in my browser, I see a popup window which asks me what to do with "default" which is a php file type.
I dont see the index.php which should actually open. What do I do to make the php files display correctly?
I have servers which contain SATA disks and SAS disks. I was testing the speed of writing on these servers and I recognized that SAS 10.000 disks much more slowly than the SATA 7200. What do you think about this slowness? What are the reasons of this slowness?
I am giving the below rates (values) which I took from my test (from my comparisons between SAS 10.000 and SATA 7200);
dd if=/dev/zero of=bigfile.txt bs=1024 count=1000000 when this comment was run in SAS disk server, I took this output(10.000 rpm)
(a new server,2 CPU 8 core and 8 gb ram)
1000000+0 records in
1000000+0 records out
1024000000 bytes (1.0 GB) copied, 12.9662 s, 79.0 MB/s (I have not used this server yet) (hw raid1)
[Code].....
I have/had a PC with several hard drives, and a mix of ubuntu and windows on multi boot.The old boot drive died screaming, and I need to start again. (But my data is safe! yay!)
Is there anything special about which drive can be the main drive to start booting from? Or to put it another way, can I install to any of the other 3 and expect it to work, or do I need to switch them around so a different drive is on the connections for the recently dead one?
I'm in the process of trying to install FC14 64 bit to my Window 7 64 bit system. This new system has a 6.0 Gb/s internal hard drive.When I reboot with the F14 install disk I have made it past the disk verification (is Verified) and then picking a language but then I get the message "No usable disks have been found". In Win 7, the Disk Management window shows that 184 GB of space are free. Is there some disk preparation that I should do to make this space available?
View 11 Replies View RelatedI'm fairly new to Ubuntu/Linux. Here's the problem I'm encountering after I tried to install Ubuntu Desktop 10.10. I was installing from a CD, as I tried to install alongside Windows XP, (The setup detected 2 hard drives, the first one was 40 GB, with all my windows stuff on it, the other was a 160 GB one), I got the message "error informing kernel about changes made to .....", which would not disappear no matter what I clicked. So, choosing the seemingly only option, I force powered down the computer. As I powered it back on.
Windows did not boot, instead I just got a black screen of nothing but a flashing _. I tried booting from the LiveCD again, which worked well enough, EXCEPT, the 40 GB hardrive full of my Windows stuff and files was not detected, and the 160 GB drive was detected only in the drives tool, but not accessible. I have no clue as to how to: 1. retrieve important files from my 40 GB drive. 2. Restore Windows XP professional.
This was a really frustrating problem which turned out to have a really simple solution, so I'll share it with people who might be having the same struggle. Problem You plug in a usb hard disk and try and mount it using:
[code]....
I spent hours - days - hunting around for the solution! (And felt a bit humiliated when I realised how simple it was!) PS, There used to be a "Success story" section on LQ, but I couldn't find it; if this is better in another section, please move it. PPS, I'm on a public computer and won't have Linux access for a looong time - if anyone can copy the message that fdisk prints out to help people who are searching for it
I would like to configure and SAN disk. But I do not have a physical SAN disk. Is it possible to create and configure a Virtual SAN disk and work on it with virtual machines?I have around 400GB of space in my Laptop.
View 7 Replies View RelatedI have downloaded NETINSTALL disk from debian.org burned it and during installation it says that error and inst will not continued. This disk havent error replace disks and reburned them. On this computer debian 6 has been installed two weeks ago. "Running post-installation trigger fontconfig" on this stage i have fail.
View 6 Replies View RelatedI got a new computer (core i7, 6gb ram, 500gb hdd).I first installed Windows 7, because I remembered how Fedora 9 created a dual-boot screen nicely, while if I installed XP on a system with Fedora 9 it would just take over the boot and boot to XP.Anyway, so Windows 7 is installed, and I got the Fedora 11 DVD install.I partitioned the hdd as thus (on win7 installation): 93gb windows system, 300gb media partition, 90gb unformatted.When I boot the installation and select the "use free space" I get an error that there isn't enough free space on the disks to create the layout.I also tried to create a custom layout, but after a few errors I gave up on that what should I do to get Fedora 11 installed?
View 9 Replies View RelatedI have installed CentOS on a VMwareWorktation and that CentOS, i also install VMware Server (suscess) and setup a guest OS that, but i start this Guest OS, an error show "You may not power virtual machine in virtual machine"...
View 3 Replies View Relatedim trying to format my 40gb hard drive and i get error ATA HTC426040G8CE00 saying one ore more partitions are busy on /DEV/SDA
View 2 Replies View RelatedI'm trying to install Fedora 13 on my HP dv6 laptop and when I try to use the Use Free Space installation type, I receive a Partitioning Error: Could not allocate requested partitions - not enough free space on disks. Before I started the install, I used the Disk Management utility in Windows 7 to shrink the volume of the C: drive down to 242 GB and leaving 210 GB Unallocated. Here is what the screen looks like when I select Create Custom Layout (also receive the not enough free space error):
Device (sda) Size Type
sda1 199 ntfs
sda2 248,018 ntfs
Free 215,175
sda3 13,443 ntfs
sda4 103 vfat
I have an command to read inputs from file2 and replace the content in file1. Issue is that the op is coming in a single line as gsub and split functions don't recognize new line characters.
Code:
awk 'NR==FNR{gsub(/input./,""); split($0,a," = ");b[a[1]]=a[2];next} {gsub(/@/,"");for (i in b) gsub(i,b[i])}1' $t2 $t3
This gives belwo op:
[Code]....
I had Ubuntu and Kubuntu installed to dual-boot using the GRUB loader installed by Kubuntu. I mistakenly formatted the Kununtu partition to NTFS in an attempt to install Windows XP in its place without updating grub to pull the files from my Ubuntu partition.
Now, when I go to boot the computer, I receive a the "error: unknown filesystem" and the grub rescue prompts for commands. I've attempted to boot from both a Ubuntu Live CD and a Secured Ubuntu CD with boot repair built into it, but receive the same message both times. I know this isn't an issue with my boot order (I've changed that), and my computer will boot into a Windows XP setup disc (which will not proceed for a different reason)
I've been asked to move data from an old external hard drive to a new one, and to make the new one compatible with the Macintosh. (The old drive's USB connection has died, and I'm connecting to old the drive using a PC card that provieds an eSATA to the drive. The recipient's Macintosh doesn't have a PC card slot, so she can't access the old drive anymore. Hence, the new drive.)
Naturally, I'm doing this data transfer using Linux. I've discovered that I can format the drive as HFS+ using mkfs.hfsplus from the hfsprogs package. But I need to know: do I need to do anything special with the partition table? Is there a special Macintosh partition table format that I need to format this disk to? If so, what tools can I use to get the right format for the partition table?
I'm looking for a way to force my PS1 variable to a certain number of chars.
It currently looks like:
$PS1="W $"
and I'm trying to keep the same number of characters regardless of the length of current folder name.
For example, both Documents and bin would be displayed as 10 character strings, keeping the left side of my terminal the same width all of the time.
I bought a 3 TB western digital but I cannot format it. I have to split into 2TB and 1TB (or less because it holds 2.73 TB actually). Is that normal because of linux does not support 3tb yet? I note that I tried into EXT4 and JFS (after tabel creating)
View 1 Replies View Related