How can I connect to a hidden wireless network on Kubuntu? I have 9.10 64bit installed, and have the information for the network (e.g. SSID and key) because I've already connected to it on Windows.
View 3 RepliesI am having a little trouble connecting to my wireless network. Running Fedora 10 32 bit.I'm trying to connect to a hidden wireless network. I updated the firmware for my driver but apparantly the driver is still not working. Broadcom has a driver from their website for Linux 32 bit systems. Should I attempt to install it? I read a post where the driver is built into the system kernel. If so I would need to blacklist the one of the drivers. Correct?
[justin@justin ~]$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
code....
When I click on the 'connect to hidden wireless network' I get a pop up window. All boxes are selectable with 'new' as the connection. If I click on that drop down and select my ESSID, all the boxes, including the 'connect' box are greyed out. If I enter new network name and the security I can get a connection. If I put down my original ESSID down as the new network name, it works, but if I then look at network preferences, I have two wireless connections with the same name.
View 2 Replies View RelatedMy network has SSID broadcast turned off, it took me several attempts before the crappy ubuntu network manager figured out that I want to connect to that network automatically.
Yesterday my laptop ran out of battery and entered on hibernation. Now, the crappy network manager can not connect to the network anymore. I tried everything. I restarted, I removed the connection from the list. But after asking to connect to the network, and enter the SSID and the WEP key, it simply won't connect.
The worst part is when I tried to load a pre-defined configuration using "Edit Connections", It displays the connection name, but the "Connect" button is disable.
Is there any way to connect to this hidden network? Or it is not supported.
connect to a hidden wireless network from command prompt? The networks ESSID is "sh0mis"
View 5 Replies View RelatedKernel: 2.6.27.15-170.2.24.fc10.i686
WLAN: Broadcom BCM4311
Problem: I run WPA2 Personal encryption on all my wireless devices. At work we use Cisco WAPs and I can connect flawlessly, simply by entering the password. At home I use Apple's Timemachine, which is basically an Airport Extreme A/B/G/N router.
I go to Network Manager and choose "Connect to Hidden Wireless Network". I enter in the SSID of my home wireless, choose WPA2 Personal, and enter in the password. After ~1 minute Network Manager spits back a window requesting the WEP key.... But I'm not running WEP. This is extremely frustrating. I delete the network and try again... same behaviour. My assumption is that this may be isolated to Airport Extreme network devices but I'd really love to find a fix. Just FYI: I have a MacBook Pro and a system running Vista that connect without a hitch.
Trying to convert from Slackware and on a less than 8 yr old gateway installed 10.04. My wireless network is hidden. Logs of the wireless router show dchp requests from xxx.xxx.xxx.45 and the associated offer back. I am assuming xxx.45 is the gateway box.When I open a terminal on the gateway box ifconfig shows the wlan0 to have the proper mac address of the usb wireless stick (intel).
I assume the proper drivers have been loaded as the mac address is recognized; I inputted the proper wep key as an address is offered by the router. Yet no internet connection. Am prepared to use the terminal [as gui screens don't seem to work] to change some file's wireless configuration setting but don't know where to look with Ubuntu.
I'm using three different UNIX OS's.I have used gnome on my laptop for most of the time I have had it and I decided it was time for a change in GUI,I am wanting to use KDE but I can't get it to work with my laptop I have tried mandriva 2010.1 spring and that one was slow and it kept dropping my wireless connection.So I got rid of that in tried Kubuntu and now it will not use the wireless.Ubuntu and Ubuntu SE and the live version of super gamer can all connect it's just Kubuntu and mandriva
View 2 Replies View RelatedFinally took the plunge and decided to give debian a go, not done so before as feared it would be too complicated. Net install went ok. Used to wiki to get me wireless up and running by copying those commands provided most of which made no sense (why the separate kernel image for wireless?).
Anyway seems to have worked so now to the problem I can't connect to my wireless network its not broadcasting so configured it manually the way I do in ubuntu through the net manager, it doesn't connect at all.
Installed 11.2 last night with KDE4. Using "Connect to other network" I could see all the private networks around, including my own.
Mine has an hidden SSID and WPA2-PSK security. Regardless of what I tried I couldn't connect. Both BSSID and password are correct (but there was no other choice than "WPA/WPA2 personal" under security).
So I go to work today and connect to an unsecure network with a visible SSID (and a lower signal quality) without any problems.
I just wanted to share how I got my wireless network working after spending several hours doing it wrong. It might be helpful to others.My wireless router is set up as a "hidden network". That is, it doesn't broadcast the SSID to prevent hackers. My laptop connected fine under Windows, but not Ubuntu.Lots of posts told me to do stuff in the Network Manager. I tried, but I couldn't find the right settings. It turns out there are *TWO* different programs that control the network settings. I was using the wrong one.
To get to one of them you go to System/Preferences/Network Connections. This program is *NOT* Network Manager. Whatever I tried to set up in this program, I could not get a working connection. The other program, the *REAL* Network Manager, is a different program altogether. You get to it by clicking the network icon at the top right corner of the screen. The problem is you can barely see it if the network is not working. When the network is down, all you can see is a tiny greyed out triangle. That's the thing you have to click. After I clicked this and followed the steps under "Connect to a hidden network".
I just installed xubuntu on my desktop. I am using a D-Link USB to connect to the internet wireless. It picks up all of the other Networks around me, but when I try to connect to my hidden network, It will not connect. I made sure the name and password is correct. I really need to connect it to the internet.
View 4 Replies View Relatedhave to connect to it manually every time i log in where i'll get prompted for the root password to connect.
things worked fine on F12.
After installing Fedora 15 on my notebook, I found that the one thing that I am unable to do is connect to a hidden encrypted wireless network automatically. I've seen plenty of people inquiring about this online but have found no solution. I can set up whatever I want to in my settings (using the old gnome2 interface setup, the gnome3 interface setup leaves the wireless options unconfigurable for some reason so I can't do anything with the "Network Name" dropdown)
All of my settings have been set up using the network manager from gnome2, but that doesn't seem to translate to my gnome3 desktop. So, is there any way to get the wireless to connect automatically on startup? I know my wireless card is working when I start my computer because it shows some of the networks in the area and I can connect to a few of the unprotected networks. This is the only problem I have with gnome3.
EDIT: from dmesg, I find the following: [485.63] ADDRCONF(NETDEV_UP): wlan0: link is not ready
EDIT #2: Going into the network settings just to play around with it, I discovered that the network name dropdown box appears to be grayed out, but now it works when I click it (didn't the first time) -- this allowed me to connect to my hidden wireless network. Still however, it does not connect automatically (system default is the hidden wireless network) and I still have the DNS problem
I have a CentOS 5.5 server running currently with a Netgear gigabit ethernet card and for wifi I have a wi-fi card with the chipset: RT2860.Now I have gotten the ethernet card and wi-fi card working but my main question is: How do you bridge the connection between the ethernet card and the wi-fi card to create a wireless network with a hidden ESSID if possible and WPA encryption? (So the server basically acts as a wireless router as well as doing all the other stuff I need to do on it).
View 2 Replies View RelatedWhen i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies View RelatedMac OS X has built-in support for internet connection sharing through the settings as in the following screenshot:
This works very well with other Macs, but I'm having problems connecting to such a network using Linux. I tried all combinations of configuration, double- and triple-check the WEP password but could never get an IP address. In a last effort I also tried without encryption, but still couldn't get my Linux box connect to the network.
I don't know if Windows has the same problem. Now I'm suspecting two things. Either I misconfigured something in my Linux installation, or OS X is doing something smart and makes it difficult for non-Apple devices to use the network (I also tested with an iPhone, it connects very well, unsurprisingly). Now what is wrong? What do I have to do?
Tried the live boot of Ubuntu 10.04 LTS on my work PC today (it has Windows Vista on it and it is literally DEAD slow). There's a wireless network in the office and the PC has a wireless network card installed.
The problem was the following - I booted up Ubuntu, the "tray" was showing the network icon. I click on it, it shows me the list of all available wireless networks. I click on the one that belongs to our office, enter the password, click "Connect".
Now, here comes the problem - after "loading" for some three minutes, the same window pops back up. No errors, no messages, absolutely nothing. The password is correct because the Windows installation and the other PCs in the office can connect just fine. Anyone knows what could be the problem? The drivers are apparently fine if it can find the networks and detect the connection encryption correctly.
I am a LINUX newbie using Ubuntu. I love it so far but I am having issues. I cannot connect to the wireless network that I am using with my other Windows PC. The problem in my opinion is that the wireless device I use isn't operating. No light comes on the device. I am not sure how to "find hardware" with Ubuntu.
View 9 Replies View RelatedI have ubuntu 10.04 netbook edition running on dell mini 10 and i cannot connect to my wireless network. I entered in everything on the editing wireless network section of ubuntu. However when I try to enter in the mac address as soon as I start typing the apply button becomes unactive. I have entered it before and I did connect to my wireless net with my netbook. However I tried top connect this morning and I wouldn't let me! I did not connect automatically to my wireless net work as it had before. I am typing this message on my desktop using the same internet connection so, I know that the net is active.
View 15 Replies View RelatedI just install arch linux yesterday. And I have an issue with the wireless connection. I can see wireless connections, when i click on thet networkmanager. But I cannot connect. If I remove WPA or any security from the wireless connection(from my wifi router) I can connect to wireless network without any issue. But when there is any security is involved to the connection it does not connect. How to connect to wireless. I've been using debian for a long time, but there was no any issue with this connecting thing. I am new to arch linux.
View 18 Replies View RelatedI'm running ubuntu 10.10, in a Gateway M-6750. I can't get my wireless to work properly.
After I lose my wireless signal, I can't connect to a network again. I have to restart my computer or, remove the ndiswrapper module and insert it again so that I can connect to the network again.
I do this with:
Also, there are sometimes when the computer freezes up when trying to search for a signal.
I have configured my system to connect to a wireless network on bootup, but now every time I boot I have to wait and watch it connect (it outputs some dhcp connect stuff) which delays the boot process. is there any way to just initialize the script and then go on with the boot process instead of letting it output some pointless crap and waiting for it to end?
View 5 Replies View RelatedI was told by an experienced Linux user/IT professional that older Broadcom wireless cards had embedded code preventing access through non-Windows OS's. I was told that there were drivers that were basically "hacks" for skirting this issue. I've tried two different drivers and neither seems to be doing the trick. My current driver is the "Broadcom STA wireless driver".
Symptoms
Recognizes my network and others
Says it's connected
Won't load any web pages
Frequently asks for authentication
I've authenticated using my network password and my router's security key
Here's what the terminal says about my wireless card:
05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: AMBIT Microsystem Corp. Device [1468:0422]
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: wl
Kernel modules: wl, ssb
I'm trying to connect to a wifi network where it hijacks all requests and redirects you to a page where you have to agree to a terms of use before it lets you connect to the actual outside world. This is a pretty common practice, and usually doesn't pose much of a problem. However, I've got a computer running Ubuntu 9.10 server with no windowing system. How can I use the command line to agree to the terms of use? I don't have internet access on the computer to download packages via apt-get or anything like that. Sure, I can think of any number of workarounds, but I suspect there's an easy way to use wget or curl or something.
Basically, I need a command line solution for sending an HTTP POST request essentially clicking on a button. For future reference, it'd be helpful to know how to send a POST request with, say, a username and password if I ever find myself in that situation in another hotel or airport.
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies View RelatedI've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedI clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View Related