General :: Asus Eee Pc 1001px Will Not Find Wireless Extensions
Aug 28, 2010
Just bought a netbook, ASUS Eee PC 1001PX, and got rid of the crappy XP pre-installed. first i put netbook remix on it, and tried many downloads and ndiswrapper to fix the wireless problem. then i went ahead and put another form of ubuntu on it thinking it might have the right drivers need to use the built-in wireless card, nothing. i dl all updates and bug fixes. i went to atheros to download the only driver they have for linux in the AR8132 class but still not helping. although i am not sure if i even installed. once dl it only extracted itself. i couldnt figure out how to run. if someone has this type of netbook it would be awesome. everything works on it except wireless and headphone jack. i know its just cosmetics but it would be nice if all hardware worked.
View 1 Replies
ADVERTISEMENT
Sep 23, 2015
I recently bought a used Asus eee 1001PX. It came installed with some spyware called windows which I replaced with jessie. Everything works great but one thing. When I plug in headphones I get no sound in the headphones. If I have some audio running and plug them in while it's playing it doesn't cut the audio from the built in speakers off like it should do. If I start and look at Output Devices in pauvcontrol it seems like it at least recognizes that I have headphones inserted.
I didn't have a chance to test if the physical audio jack was broken while it had Windows running on it but assuming that it's not physically broken, what might be wrong? I know very little about audio, alsa, pulse and that kind of stuff so I hardly know even where to start.
Some info:
Code: Select alllspci -v
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 8437
Flags: bus master, fast devsel, latency 0, IRQ 44
Memory at f7cf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
[Code] ....
View 3 Replies
View Related
Aug 15, 2010
If I would like to update my kernel to linux 2.6.34 on my asus eee 1001px laptop. How can I do that in the easiest way? I already downloaded the kernel from kernel.org.
View 7 Replies
View Related
Feb 28, 2011
I have problems installing Ubuntu Netbook Edition (ubuntu-10.10-netbook-i386.iso)on Asus eeepc 1001PX. code...
I have tried both Universal-USB-Installer-1.8.3.3.exe and the Ubuntu start up disk creator to prepare my USB-stick.
I have earlier installed the Ubuntu desktop 10.10 on the same machine with the same method without problems.
View 6 Replies
View Related
Dec 24, 2010
I've been looking for info about Legacy OS but havent found much. I installed it and all works great except there are no active wireless extensions.My laptop have an internal wifi adapter (bcm43xx) I tried to load that driver using legacy OS network wizard but didnt work, the other is a external wireless card with a rtl8187 driver, this last one is the one I want to be up. I also tried to use ndiswrapper but can't set it up either.
View 1 Replies
View Related
Jul 11, 2011
I have a deep folder structure on my RHEL 5.x file system which is supposed to have only word(*.doc, *.docx) or pdf(*.pdf) files. But I want to check if there are files with any other extensions which exist. Is that possible?
View 2 Replies
View Related
Mar 28, 2010
A friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
View 7 Replies
View Related
Mar 2, 2011
I am doing a migration and where i face problem with few file formats . I have the list of acceptable file formats , now i need to find the rest of the file formats other than the acceptable file formats. is there any tool available for this ? or can some give me the VBA macro .. My VBA macro works to find the file extension in a particular folder but the problem is its ending when the count increases to 65000 (excel limit). How do i use If condition here to avoid the acceptable format and give me unique file formats .
[Code]....
View 1 Replies
View Related
May 26, 2010
I'm trying to find all the files in a specified directory that do NOT end in .archived or .error and are older than 30 mins. Currently I have: Code: find /opt/edi/incoming -type f ! ( -name "*.archived" -name "*.error" ) -cmin 30 But I keep returning files that end in those extensions and I'm not sure if I'm using -cmin correcty? If there is a better way to do this (perl, etc) I'm open to options, this is for a nagios check.
View 2 Replies
View Related
Dec 28, 2010
I have a directory of a load of files without extensions. I know what the filetype should be, so is there any way of batch renaming the files to append a given extension onto it. i.e. text would be renamed as text.txt?
View 3 Replies
View Related
Aug 24, 2015
iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
Whereas I am using wireless internet ...
View 14 Replies
View Related
Feb 22, 2011
I just installed Slackware 13.1 on my Asus 1215T, and I've been trying to get it to connect to my wireless network in my home. When I type iwconfig I get no wireless extensions, and ifconfig returns only lo, no wlan0. I read the Slackbook wiki and tried to configure the inet1.conf and wireless.conf but still no luck...
View 12 Replies
View Related
Mar 24, 2010
I have a fresh install of Karmic on a older compaq laptop. I initially had LAN access, but not wifi. I added a few Broadcom packages using synaptic, and then neither worked. Then I removed the same packages, but I still have no internet access, LAN or wifi. Here are some of my settings. vincentertainment@vincentertainment-laptop:~$ iwconfig
[Code]...
View 1 Replies
View Related
Apr 9, 2010
I wanna see the wifi signal strength.But when i run the command iwconfig , it tells me 'no wireless extensions'.By googling I found that I need to enable config option CONFIG_NET_RADIO.I see that this has to be done in boot which has config files.So I typed the command grep CONFIG_NET_RADIO /boot/<config-2.6.31.5-127.fc12.i686> (my fedora version is 2.6.31.5-127.fc12.i686).But I got the error as "bash: syntax error near unexpected token `newline' ".I dont know the reason.I also want to know if I have to install driver(ndiswrapper)for viewing wireless signal strength.I thought that the drivers will present default(am not sure).
View 9 Replies
View Related
Aug 26, 2011
A friend of mine have just migrated to Linux, and as recommended by me, He's trying Fedora 15 KDE. Everything runs just fine, he loved the OS, but there's a sad problem, his network card seems to have no "wireless extensions", which makes the system impracticable to use. I've tried searching around which card JMC250 is a single-chip PCI-Express Gigabit Ethernet Controller
with lspci
and which driver for this card
JME
is installed, with modprobe list
I've tried loading this driver with modprobe jme, no errors. And I've also tried compiling a driver I got from the manufacturer. No changes.
View 13 Replies
View Related
Jul 19, 2011
I have an Asus U52F laptop with the Intel 6050 network adapter.
Code:
# lspci | grep WiFi
02:00.0 Network controller: Intel Corporation WiMAX/WiFi Link 6050 Series (rev 5f)
I've downloaded the Intel firmware and dropped it into the correct location according to the README.
Code:
# ls -l /lib/firmware | grep iwl
-rw-r--r-- 1 root root 469780 Jul 10 13:18 iwlwifi-6050-5.ucode
I am using the current module from compat-wireless. When I modprobe iwlagn, I get no error message, and the module shows up in lsmod.
Code:
# lsmod | grep iwlagn
iwlagn 158054 0
mac80211 179615 1 iwlagn
cfg80211 139799 2 iwlagn, mac80211
However, no wireless devices show as being attached to my system!
Code:
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
I also see errors in dmesg.
Code:
# dmesg | tail
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
iwlagn: Copyright(c) 2003-2011 Intel Corporation
iwlagn 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:02:00.0: setting latency timer to 64
pci_resource_len = 0x00002000
pci_resource_base = ffffc90016384000
HW Revision ID = 0x5F
pci_enable_msi failed
iwlagn 0000:02:00.0: PCI INT A disabled
iwlagn: probe of 0000:02:00.0 failed with error -1
Distro: CRUX (64-bit contrib)
Code:
# uname -r
2.6.38.2
View 3 Replies
View Related
Jul 2, 2011
I just can't get my wireless to work so I can get started with learning Linux. Here is a bit info about my setup, I have tried it both ifup and Network Manager version 0.8.2-15.20
[Code]....
View 6 Replies
View Related
Jan 3, 2010
Hello, I have a problem with wireless internet on my laptop - Acer TravelMate 2413LMI with Broadcom BCM 4318 card.
Below are ifconfig, lspci and iwconfig outputs:
ifconfig:
eth0 Link encap:Ethernet HWaddr 00:0a:e4:e6:86:b5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:20 Base address:0x3000
lo
Link encap:Local Loopback
code....
I forgot to mention that the problem occured after linux 9.10 installation
View 1 Replies
View Related
Dec 26, 2010
currently running karmic on an old gateway laptop with kernel 2.6.31-22-generic and, as is par for how I handle challenges, I've jumped in with both feet - which is to say this is not a dual-boot situation. I've spent some time reading the forums (and other sources of information) and am grateful for all the knowledgeable people who are willing to share what they know.
My operating system seems to be functioning properly.I can get online via ethernet, but not via wireless. I have a lucent orinoco gold PC24E-H-FC (PCMCIA) card, which the computer isn't seeing. I am trying to follow the instructions here: [URL] to install the driver. Everything is going well until I get to the sudo make line. At that point I get the following display:
make -C /usr/src/linux-headers-2.6.31-22-generic M=/usr/src/orinoco-0.15rc4 KERNELRELEASE= modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.31-22-generic'
/usr/src/orinoco-0.15rc4/Kbuild:8: *** Wireless extensions are not enabled. Stop.
[code]....
how I can fix it so I can continue on with the instructions. (For the record - if I just continue on, I can change directory in the next line, but I cannot remove either hermes or orinoco as "no such file or directory" seems to exist.)
View 3 Replies
View Related
Mar 11, 2010
The adapter I purchased (Zonet ZEW2508 ) uses the Ralink 2070 chipset - a fact that originally excited me because Ralink seems to be fairly loving to the Linux community. However, despite my best efforts I can't get the thing to work. Initially I tried following directions to set up the driver you can download from the Ralink website. The directions I found were written February first, and Ralink updated the driver February eighth - so as far as I can tell the directions no longer work. After screwing around trying to figure that out for a while I decided to give ndiswrapper a go.
Initially this seemed promising. I just harvested the drivers from the CD and followed one of the many ndiswrapper directions available - most helpful seemed initially to be the Ndiswrapper Troubleshooting Guide found in this forum, however the solutions offered there didn't work either. When I throw an ndiswrapper -l into the terminal it looks promising at first, it tells me the driver is installed and the device is present, but it just doesn't work. When I try iwconfig, or iwlist scan it tells me "no wireless extensions," and "interface doesn't support scanning" respectively. The only devices even listed are lo, eth0, and pan0. There's no wlan0 or anything of the sort.
View 1 Replies
View Related
Sep 26, 2010
I'm trying to install from a USB drive. I followed the instructions given on an Ubuntu website, only to get the following output when booting from the drive:
SYSLINUX 3.86 2010-04-01 EBIOS Copyright (C) 1994-2010 H. Peter Anvin et al No DEFAULT or UI configuration directive found!
View 3 Replies
View Related
Jul 4, 2011
I'm following this guide[URl]... And, after a thousand of bad words, it works But w_scan doesn't find any channel! Have you experience with this DVB-pen? I'm using Slackware 13.37 x64
View 2 Replies
View Related
Apr 8, 2010
I am trying to clone a working Centos 5.4 system onto a new box with a ASUS P5KPL-CM motherboard. I have done so by plugging in a Realtec lan card - but can't get the motherboard lan working. Googling tells me the motherboard has a Atheros L1E lan chip - but I have installed several kmod drivers from ELREPO - but still can't get the on-board lan working. So far I have installed:
kmod-atl1e
kmod-atl1
I have just installed these with yum - but no new hardware appears in the network gui dialogue. Am I missing some step here - or is there another driver I should be looking for.
View 5 Replies
View Related
Jul 3, 2011
I am attempting to setup wireless in Slackware 13.37 for the first time and while I found a lot of guides I am still unable to connect to my router without starting X and using wicd. I'll post my rc.inet1.conf and rc.wireless.conf along with wireless-settings.conf from wicd. wireless-settings.conf
Code:
[00:26:F3:22:33:7A]
automatic = False
[00:26:F3:22:33:79]
afterscript = None
dhcphostname = Doctor
bssid = 00:26:F3:22:33:79
[Code]...
View 3 Replies
View Related
Oct 19, 2010
I just installed slackware 13.1 on my notebook...all instalation step was success. But then everything is just like "a jungle" for me. So there will be a lot of next question post from me for this time, i wonder about the LED wireless that always ON. The Hotkeys is work i thought, because when i on/off it and i check it by "iwconfig" tx transmits going to off/0dB.
View 2 Replies
View Related
Jul 5, 2011
I currently know next to nothing about networks in Linux (yes I am working on that). I have just brought a Asus n13 wireless adapter after failing to get my laptop wireless working. I am using the 2.6.32-5 Debian squeeze kernel. The device connected once after I did the following:
apt-get update
modprobe rt2870sta
iwconfig
ifconfig wlan0 up
The device connected to wifi and was working fine. I then shutdown and rebooted to see if it would automatically connect on start up and now, although nothing seems to have changed and even after I repeated the steps above it did not connect. The network manager applet as well as listing the asus adapter(as ralink 802.11 WLAN) lists a Texas instruments PCI1410 pc card cardbus controller which i didn't before.
This is the output of iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 Ralink STA ESSID:"" Nickname:"RT2870STA"
Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Link Quality=10/100 Signal level:-39 dBm Noise level:-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon: .....
pan0 no wireless extensions.
This is lsmod | grep rt2:
rt2870sta 326811 1
crc_ccitt 1039 2 irda,rt2870sta
usbcore 98453 5 btusb,rt2870sta,uhci_hcd,ehci_hcd
View 10 Replies
View Related
Jul 16, 2015
I just installed a fresh install of firmware-8.1.0-amd64-netinst.iso. During installation the wireless setup utility located my wifi-network and upon entering my WPA password it said it was connected. It didn't work however so I plugged in my ethernet cable and continued the install process hoping it would magically start working after that. No luck.
I went from an Arch Linux install with working wifi, and I dual-boot my box with Windows 7 with working wifi, so I know it's not the card or the distance from the router.
View 1 Replies
View Related
Jul 20, 2010
I haven't been able to find anything really useful on google either. Was hoping you guys could point me somewhere or explain a process that might work. What I've tried so far is downloading the driver from ralink and trying to follow their procedure for getting it setup. Following the readme I get lost at step 3 and attempting to make it, I get:
[boardbox@niflheim ~]$ cd Desktop/2010_07_16_RT2860_Linux_STA_v2.4.0.0
[boardbox@niflheim 2010_07_16_RT2860_Linux_STA_v2.4.0.0]$ make
make -C tools
[code]...
but this hasn't fixed my problem either. I can see networks but I can't connect to anything, so kinda still stuck at square one.
EDIT: Turns out in frustration and absent-mindedness I didn't reboot and that fixed it.
View 1 Replies
View Related
Jul 26, 2011
I recently purchased an Asus n10 wireless usb adapter to use with my media server, running Ubuntu 10.04 LTS (Lucid Lynx). After spending several hours today with many of the threads (especially this one about the Asus n13) it seems that I've run out of ideas.
My network is running a hidden (non-broadcast) SSID ("Potato") with wpa2 personal encryption.
Here is the relevant information from lsusb:
Code:
Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer Inc.
Iwconfig follows. The rest of the values, like link quality & etc, are all zero:
Code:
wlan0 802.11b/g ESSID:"Potato"
Mode: Managed Access Point: Not-Associated Bit Rate: 0kb/s
And the kicker is that the interface doesn't seem to be available, despite the above reports. ifconfig wlan0 up produces:
Code:
SIOCSIFFLAGS: Resource temporarily unavailable
View 9 Replies
View Related
Feb 17, 2010
Under OpenSuse 11.2 i cannot connect to my wireless network. Sometimes computer doesn't see network, sometimes computer cannot connect to it. Encryption: WPA & WPA2 Personal Kernel driver: ath5k Also I am embarrassed that in lspci and yast written various models of my wifi adapter.
Code:
linux-ra0h:/home/miksayer # lspci | grep "Wireless" 01:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
View 9 Replies
View Related
