Fedora Servers :: How To Setup A Intel Xenon Power Edge 1900
Aug 31, 2009
I need to setup a Intel Xenon power edge 1900 server, which fedora version (10 or 11) suits it best and whether I should go for 64bit or 32bit (If I go with 64 bit some applications wont support it). I also have another issue, currently on another Intel Xenon power edge 1900 server on which Fedora 9 32bit version is installed, tough the server has 8GB ram, fedora can access only 3.2 GB. How can I solve this issue and will it repeat in the new server where I install fedora(10 or 11).
View 1 Replies
ADVERTISEMENT
Dec 27, 2009
I'm running FC12 x64on a Dell PE2950 to host some virtual guests, but FC12 host drops CPU errors (IERR asserted) and reboots whenever CPU utilization jumps above 30-40%. Found mention here from end of 2007 checked /proc/cpuinfo and DO have the 38 bit addressing processorsDoes anyone know if there's a kernel module I can load or am I going to have to custom build a kernel with that module available? What mod is it?
View 5 Replies
View Related
Apr 20, 2011
Im having a bit of an issue installing Ubuntu Server 10.04 on a Dell Power Edge 1850. I am running RAID1 via the onboard PERC4 controller that is set to emulate MASS storage. I am able to boot from the disk and run through the initial setup, however, when I give it the go ahead to start the partitioning it hangs up on 33%. It does this on both the Guided full disk and guided full disk LVM. I have run a check on the disk as well as memory.
View 6 Replies
View Related
Feb 16, 2010
I am running Ubuntu 8.04LTS x64 on a Dell Poweredge 1900 with a Perc 5i RAID Controller. There are 3 500Gb SAS drives in a RAID 5 configuration. The Kernel is Linux dtpfs 2.6.24-27-server #1 SMP Wed Jan 27 23:39:33 UTC 2010 x86_64 GNU/Linux Approximately once every 1 - 2 months I have a problem where the disk usage starts to rise for no apparent reason. When I run df the usage grows steadily over 2-3 days from 26% to 100%. At this point Samba reports that the disks are full. Baobab does not report the additional usage and the tape backup ignores the 'extra' usage and just backs up what was previously there. When I reboot the machine the usage is set back to normal and we can continue.
View 2 Replies
View Related
Nov 3, 2010
Actually we are trying to upgrade Memory in Dell PowerEdge 1850 it has 3 memory banks and each bank has 2 slots and it supports max of 12 gig and 16 gig we r2 4gig rams. The box is running with Debian Os with kernel 2.4.X we have upgraded the bank-1 and bank-2 with 2*2G.B rams total of 4 RAms with 8 G.B The Problem is Bios is showing 8 GIG but at the operating system level it is showing about 3049 gig instead of showing 8 GIG.
View 5 Replies
View Related
Feb 10, 2010
I am trying to get a understanding of how to install a RAID 1 on a Dell Power Edge server.
HARDWARE:
2 - 16gig SCSI dives
1 - 36gig SCSI drive
I have read through some documentation found online and at centos.org but still having problems.
get this accomplished keeping in mind this is my first go at using RAID system.
View 4 Replies
View Related
Feb 1, 2015
I'm having problem in installing debian 7.5.0 on Dell Power Edge R 470 1U Rack Server ( Not Sure If am using RAID 1 ) whereby the hard drive is not detected. This server is running 2 Proc/2x1.2 SAS HDD . The installation went ok until i reached into partition section whereby the drives is not there to be selected , throwing an error " No disk drive detected , Driver needed fro your disk drive "
I've tried to use debian-7.8.0-amd64-DVD-1.iso
My server details:
Dell Power Edge R 470
32GB RAM
2 x 1.2 TB SAS HDD
View 4 Replies
View Related
Oct 29, 2010
Im trying to limit the diskspace users on the system may consume, and i found quotas (im a total linux noob). But when i try to set it, no matter what i set it to the maximus is 2 GB. Now... i need quite a lot more than that. One user should be able to use 1900 GB and the other 600 GB. How can i fix this? Im using ubuntu server 10.04.
View 9 Replies
View Related
Mar 19, 2010
According to firestarter, there's some process on my machine that keeps trying to access port 1900, every two minutes exactly. I don't know what it is. I've tried netstat -tnlp, but it doesn't show up. Presumably I have to do it at the exact second the process is trying to access the port. Does anyone know of a bash subroutine that will keep doing netstat -pl until it finds a process on port 1900?
View 4 Replies
View Related
Aug 19, 2009
Been trying to setup SSH on the Linux box for a long time and still no success.
AIM: To be able to SSH from the internet.
I CAN ssh locally.
I CAN ssh on the LAN to the Linux box.
I have even changed distro from Ubuntu to Fedora.
Everytime I try to SSH from the internet I get connection timed out.... I have setup port forwarding correctly on my Netgear router, when a SSH request hits the router I can see it in the logs. I have port forward setup for FTP service to my windows 2003 box which all works fine, so port forward works and I know what im doing regards that.
"iptables -L" shows no policies in place, the GUI firewall is DISABLED.
Even tried service iptables stop
I have made no changes to sshd_config, its set to standard port 22. At this moment in time I dont care about firewalls/security just need to get this working as a inbound request comming in from the internet.
the hosts.allow file I have added 2 lines
ALL:ALL
sshd:ALL
View 14 Replies
View Related
May 28, 2010
I am very confused in setting a SVN server with repository
View 4 Replies
View Related
May 4, 2011
This is very likely a silly question but .. where is the power management setup in KDE? I have set it up before in Slackware 13.1 but now that I'm running 13.37 I'd like to set it up again but can't seem to recall where to set it up.
View 2 Replies
View Related
Nov 15, 2009
i have been searching ways to setup an ftp server. but it seems, everything i tried does not work or not what i wanted.how to setup an ftp server, allowing only permitted users. I'm using the desktop edition live cd.
View 4 Replies
View Related
Nov 20, 2009
I want to setup a webmail server or something like that on fedora 11. How to do so?
View 2 Replies
View Related
Apr 27, 2010
I have Fedora 12 x86_64 installed in my computer. I have also installed system-config-httpd, but when I go to System --> Administration --> Server Settings --> HTTP, nothing shows up.
View 4 Replies
View Related
Oct 28, 2010
I put together a little computer recently to hook to a TV.The problem I'm having is that when I start the computer up and get to the desktop... the desktop is off the edges of the screen. I checked the resolution and it's 1920x1080.I can't see the panels my applications menu, as they're both off the edge of the screen. Is there anything that can be done to correct this? Also, the TV has no settings to correct this problem.
View 2 Replies
View Related
Apr 7, 2009
I want to setup a mail server on my LAN. I want to send e-mails from 1 system to another systems.
View 8 Replies
View Related
Jun 17, 2009
I'm trying to setup eRuby on my Apache server, and I'm having problems. Currently, I have this in a separate config file in "/etc/httpd/conf.d/eruby.conf":
Code:
AddType application/x-httpd-eruby .rhtml
Action application/x-httpd-eruby /cgi-bin/eruby
DirectoryIndex index.rhtml
I have a file named "index.rhtml" in a folder called "test" that's in the root of my server. When I try to get to the file I get this, though:
Code:
You don't have permission to access /cgi-bin/eruby/test/index.rhtml on this server.
View 3 Replies
View Related
Aug 1, 2009
I have a small office setup all on public ips and was trying to work out the best way to move the wearhouse computers on to private ips and leave offices on public ips I have server with 2 nics and i have two switches What i am after is how to set it up so all computers can still see each other but private can not access net All the office computers via switch 1 Public IPs All the wearhouse computers via switch 2 Private IPs
1 DHCP server
3 Routers from ISPs going to switch one
Both switches going to DHCP Server
View 2 Replies
View Related
May 29, 2010
Setup a SVN for my network
Please tell me the complete steps for that
View 3 Replies
View Related
Jul 25, 2010
I'm trying to setup nagios, and I've looked at several guides but none of them seem to address my problem.Here's the clearest guide that I followed URl...I followed all the instructions on that basica guide, except disabling SELinux. I changed SELinux rules based on URL...I'm not getting any AVC Denials, so that's not the problem. Nagios and Apache both start fine. If I go to my local IP, I get the standard Apache test page. URl...(address from all the guides I read) doesn't resolve.I know that Nagios is at least running from "service nagios status," and I have gotten two alerts emailed to me: swap alert (I don't have swap configured) and disk space.
View 5 Replies
View Related
Jun 19, 2009
I just configured my first Directory Server. I was looking to use PHPLDAPADMIN to start administrating it. Any good how to's or Tut's?
View 4 Replies
View Related
Oct 19, 2009
is this command exact or do I replace anything with my own setu
" yum install mysql mysql-devel mysql-server "
who can't tell what has to be changed for "My server name" and "my setup"
View 8 Replies
View Related
Feb 26, 2010
I've installed Fedora 12 Desktop in order to develop a simple website, which is going to use some PHP.
I will need:code editor to write html/css/php local apache server running php browser how to get me up and running in no time with least extra configurations.
Bonus: I'm going to run all this in a virtual box on my company computer. I'd love to be able to stay undercover with this, so if one of you can tell me how to configure the apache server not to be too visible to the company network/domain, that'd be excellent.
View 7 Replies
View Related
May 10, 2010
You are running tftpd as an on demand server i.e. it is only fired up when it is needed. Services run by xinetd are always run on demand. Have you actually tested if tftp on another system can access your PC i.e.
Code:
tftp your_pc_ip_address
View 2 Replies
View Related
Feb 14, 2011
As I do not want to entrust my firefox data Mozilla's Server and have a server runnig anyway, I wanted to setup a server which provides weave service. I found this and know from different sources of the web that this indeed works: [URL] It is a stripped down Weave server intended for personal use. All in all, it does not sound to complicated. The developer says
Quote:
You ll need a relatively recent php with sqlite, mbstring and json support, and apache, preferably running ssl. Give it a shot and let me know how it worked for you in the comments. I have Fedora 14. Only problem is that Fedora does not provide a php-sqlite package. For this I found a repo [URL] So I installed php-sqlite (as well as php-pdo, php-cli and php common) with
Code:
yum --enablerepo=remi intstall php-sqlite
In consequense all php releted stuff was replayed by remi provided packages. In addition I installed json to get JSON support. The author describes the setup quite easy as follow:
Quote:
SERVER SETUP
Add the following line to your apache config:
Alias /weave /<path to this folder>/index.php
Restart your apache server. Point your browser at h[URL]. Enter "blah" for the username and garbage for the pwd. Auth will fail, but it will create the db (you can cancel the subsequent request for auth). You should now see a file called weave_db in the directory.
You can create and delete users by running the create_user script.
CLIENT SETUP
in about.config, set extensions.weave.serverURL to [URL] You can run it under http, but this is insecure and not recommended.If I disable or set SELinux to permissive mode I can point my browser to [URL] Here starts the trouble. After attemping to login no weave_db is created. I tried even 777 permission in that directory. I can run the create_user script with php and add a user, but the database does not seem to be recognized, I am unable to login into weave service.
View 4 Replies
View Related
Mar 15, 2011
I know what I need to do I just cant seem to achieve it and that is correctly setup a DNS server that works over the internet, I'm using BIND9 with webmin. I have Fedora 14 - Apache is install its all working locally, so this final step I just can't grasp to be honest.
View 14 Replies
View Related
Jul 14, 2011
I need the complete reference guide to set up my own SQUID transparent proxy Server with Gateway support. I am using Fedora 14. Please help me with LINKS/REFERENCE. I am a learner in Squid.
View 1 Replies
View Related
Mar 14, 2010
I ended up setting up a basic linux file server as a pdc for that office. Our main office is a windows 2000 ads domain. The two offices are connected with a vpn. I only have two users at the new location so I simply have the linux and samba usernames/passwords setup manually. I would like to know if it is possible to setup a domain trust between the two sites so I don't have to create a username/password in the remote site for every user at the main office to access. I did some searching but came up empty.
View 5 Replies
View Related
May 12, 2009
I am wondering, what is the status of Intel GMA X4500 driver on Fedora 10.
View 2 Replies
View Related
