Just Installed Fedora 10 on Dell PowerEdge 2950. Installation went fine. Problem is I cannot Assign a Ip address to eth0. Service "NetworkManager " dies on its own "ifconfig eth0 192168.0.8/24" works though.
View 6 Repliesi know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
my Apache2 was running fine for a while. Bur yeserday when I tried to start it again after a couple of weeks of vacation, I got the message:
* Starting web server apache2 [Sat Mar 20 10:48:12 2010] [warn] The Alias directive in /etc/phpmyadmin/apache.conf at line 3 will probably never match because it overlaps an earlier Alias.
[code]....
I was trying to assign the static IP address of my internet connection to my home server and managed to make a mess of it. I've configured the router to assign it the address every time but when I rebooted everything the server is cut off from the network completely (rather unfortunate with a headless server...). The only file I've edited on the server when trying to do this is /etc/network/interfaces, everything else network related is default. My intention in editing the file was to make the server accept the IP address assigned by the router since the router was already configured to assign the right one. I put in
Code: inet dhcp in the /etc/network/interfaces file, is that wrong? What is that line supposed to be?
Every time I upgrade my system I run a post install script. This script made some harm to the network start that prevents sshd from starting, but I was unable to detect the problem. In my boot.log I found this:
[...]
Starting NetworkManager daemon: [ OK ]
Starting Avahi daemon... Jun 2 14:58:48 Antares kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
[code]...
So there is a "bind to port 22 failed" probably caused by "eth0: link is not ready", but after the sshd init script fails the eth0 is ready...
I noticed that my internet connection wasn't automatically brought up each time I logged into Fedora so I opened the system-config-network tool and edited my network adapter by checking the box marked "automatically start at boot/login." To my surprise, the connection went down and upon trying to click on the device to let the manager bring up the connection the greyed-out phrase "device not managed" appeared underneath the device name and wouldn't allow me to connect.
Even when I used ifconfig/dhclient to get the connection up nothing happened. I could get the router to assign an IP address through DHCP, pinged a few sites to make sure it was legit, but still couldn't use firefox to browse anything. Seems as if network manager GUI is conflicting with command line attempts to bring the network up. I'd like to permanently disable system-config-network if possible because it's acting screwy!
Consider the following program:
Code:
#include <stdio.h>
#include <stdint.h>
[code]...
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
how to assign a address to my ethernet card all the options available
View 1 Replies View RelatedI downloaded Fedora 10 32bit and put it on a Dell Dimension 8200 to save it from the recycle bin. Everything seems to work except I cannot get an IP addr. Roadrunner is my ISP using a cable modem and a Linksys Instant Broadband Series Etherfast Cable/DSL router model BEFSR41. In system-config-network, the nic shows inactive. If I activate it a window opens saying "determining IP information for eth0". After a short time the message adds the word "failed". Using a Windows PC on the same network, I can look at the DHCP connections on the Linksys and I see the MAC addr for the PC running Fedora.
From the OS installation, /etc/sysconfig/networking/devices/ifcfg-eth0 has following:
DEVICE=eth0
HWADDR=00:80:ad:d1:88:c9
ONBOOT=yes
[Code]....
I am trying to get networking up on an old PII which I have successfully installed with FC4. There is a link and activity on the onboard interface because I see the indicator lights. The controller is a 3Com PCI 3c905 Boomerang 100baseTx @ 0xdc80.The only message returned by dmesg about eth0 is "Dropping NETIF_F_SG since no checksum feature."The driver module, 3c59x, is loaded as well as the mii module that depends on it.There is something about "unknown parameter`irq'" in the dmesg text regarding the driver.I noticed that eth0 is sharing an IRQ with the UHCI Host Controller.That should not be a problem, but it should not be necessary. And I could do away with USB if this is a conflict and that is the easiest way to solve it.When I drop to console at runlevel 3, and call dhclient, which is installed, I get a message telling me there is no reply to the dhcp request.I don't think the problem is on the router/switch side.
View 5 Replies View RelatedSince I have a new internetaccount, 2 days ago, I have a problem on my server [Fedora Core 8]. I use it as a router.
eth0 is for the internet.
eth1 is for my LAN.
But since my new internetaccount my server uses eth1 for the internet. This is a line from my syslog:
Code:
NetworkManager: <info> Policy set 'System eth1' (eth1) as default for routing and DNS. I killed the NetworkManager daemon and now it works but this must not be the way to do it? Where do I tell my server that I use eth0 for routing and DNS?
after a yum update on my CentOS 5.3 I got this error when shutting down eth0 on reboot...
Shutting down interace eth0: Device eth0 has MAC address XXX instead of configured address XXX ignoring [FAILED]
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedIm running samba on fedora core 7, im abit new to the server part of fedora, i set up samba and it runs well, only issue i have now is resolving permissions( User Rights)i have a shared folder which has alot of files and many subfolders in it, the files and folders in this shared foldr were copied from our old Novell Server through samba, i need to assign permissions to this folder where by a defined usergroup can have full read and write permissions to all the files and folders and sub-folders in the shared folder. i tried doing it in GUI but i realized there were over 1000 subfolders.is there a command i can run in the Terminal to help me assign the permissions?
View 1 Replies View RelatedIs there a way to use dhcpd to assign vpn clients their IP and configuration?
I'd like to have dhcpd listen on br0 (already set as 10.0.0.1) so that devices conecting through eth1 and tap0 (should I be using tun?) will get the same address pool.
I have a fresh installed redhat 9 with 1 network card attached may I know what command will I type to assign 10.0.0.1 on the network card?
and also when I type hostname it always reply localhost.localdomain
how can I assign a hostname
I want to assign a static ip address, my network/interfaces files shows
Code:
auto lo
iface lo inet loopback
am I correct to add
Code:
iface eth0 inet static
address 10.42.43.10
netmask 255.255.252.0
gateway 10.42.43.1
or is there more I need?
I have set up a cloud (Ubuntu) environment in my test lad and it's working fine I am confused setting up the public IP in the production environment. The cloud instance will get only a Internal IP address ( Private) we cannot bind the Public Ip to the cloud instance as it uses Elastic IP, so I am confused how can I set up this if I have about 250 Public Ip to 250 cloud instance. How will I map this 250 Public IP with the 250 internal IPs is there any hardware device.
View 3 Replies View RelatedI am a certified newbie into linux. I am using now ubuntu 9.04. Now here is my question. Is it possible to assign your own IP address on your ubuntu desktop, I mean a fixed IP address? Because everytime I start my computer, my internet service provider will automatically assigned a NEW IP address to my computer, but when I'm on windows the ip address is fixed.
I've installed and configured lampp and joomla. I am trying to learn how to use the joomla under ubuntu using only my computer as my local host. But when I restart my computer, the IP Address that is assigned is different to what I used when I installed joomla so I cant access my website even if I am using the same computer when I installed it. Is it possible to assign a fixed IP Address to my computer under ubuntu.
I am running Linux AS4 Update version. I have one lan card and the primary IP-Address is 192.168.0.215 & subnet is 255.255.255.0
Now I want to assign an alternative IP-Address on the same card & the IP I want to assign is 192.168.15.215.
I run the following command from root user:
Now when I ping this IP 192.168.15.215 From Windows machine then its reply me & properly reply comming from this Ip.
But when I want to access this Ip by \192.168.15.215 from run prompt then it gave me error. The specified network name is no longer available..
I already restart the machine & network service but the problem remains same.
I recently just upgraded from humble Linux user to confused Linux admin of my own virtual Linux server. When I issue the ifconfig command I get following output.
Code:
venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:1.2.3.4 P-t-P:1.2.3.4 Bcast:1.2.3.4 Mask:255.255.255.255
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
The WAN IP of the interface is not really 1.2.3.4 I just changed that IP for security reasons.What I am trying to figure out, is it possible to assign a private IP address to the same interface or can I only have one IP address per interface. I understand I have a mask of /32 so I am not going to be able to subnet the address to create any more addresses, so I assume I am stuck with the WAN IP (public IP) that I have, and just need to deal with it.
The reason I ask this is because I have been reading through several DNS/BIND tutorials/walk-throughs, and a lot of them specify setting up a intranet access with 192.168.1.1 address for the local DNS server, but since I am connecting to the sever via SSH I figure I do not need a private IP address.
In my red hat Linux machine there was a Lan card using eth0. IP is asign to that network card and it is functioning properly. I add another ethernet card in my linux machineit was detacted and when i use the commandQuote:[root@localhost root] # ifconfig -ait show me both eth0 and eth1 lan cards.I can see Ip address in my eth1 ethernet card but When I enter into
Code:
[root@localhost root] # cd /etc/sysconfig/network-scripts
and i use ls command it only show me the file ifcfg-eth1 and with
[code]...
I am using internet in my home PC using Red Hat 9. To assign static IP to my linux machine I use "System Settings....> Network" and then double click on "eth0" to assign the static IP.Well these all settings by using GUI interface.Kindly guide me that if I use only command line interface "runlevel 1" then in that case which file should i edit and assign my static IP,Subnet Mask,Default Gateway DNS settings.2- 2nd thing is,is there any way that I may open web broswer in command line? or the administrator should only use internet on Run Level 5 ?
View 14 Replies View RelatedI am running Linux AS4 Update version. I have one lan card and the primary IP-Address is 192.168.0.215 & subnet is 255.255.255.0
Now I want to assign an alternative IP-Address on the same card & the IP I want to assign is 192.168.15.215.
I run the following command from root user ifconfig eth0:1 192.168.15.215 netmask 255.255.255.0 up
Now when I ping this IP 192.168.15.215 From Windows machine then its reply me & properly reply comming from this Ip.
But when I want to access this Ip by \192.168.15.215 from run prompt then it gave me error.
The specified network name is no longer available..
My server is Linux (centos 5.3). In Server System Dhcp server is running, so it assign ip address to client windows .....
1. I want to assign ip address to Printer (printer Hp laser 3055 )
2. How do I configure cups (Network Printer) in linux server
3. How to configure printer in windows client....
How to do this.
I want to assign an address location to a pointer and wanted to display the value at that memory location.I wrote a small program for this and it is like this : (i am using gcc 4.4 compiler)
# include "stdio.h"
int main()
{
unsigned int *a;
a=(unsigned int *)0x3f8;
printf("%u",*a);
return 0;
}
But it is giving Segmentation fault
i am trying to assign a Static IP address and for the life of my i cannot get it to work Can someone explain to me the easiest way to do it and if i restart the server it won't get lost either.
View 1 Replies View RelatedI'm using Ubuntu 9.10, and I want DHCP to assign an IP address automatically. I can ping my router, and get a reply. I just have no idea how to do this.I'm trying to get my Ubuntu machine onto my Windows network.
View 9 Replies View RelatedI want to setup 1Gbps our lab network and we purchased 'Buffulo Giga layer switch ' with 24ports. Is there a way to tell DHCP to assign specific IP to a particular MAC address of a machine ? We want to use DHCP and whatever the port we use ,it should have same IP ..
View 1 Replies View Related