Fedora Networking :: Connecting To Internet Through GPRS?
Mar 27, 2009How can I connect laptop to internet using GPRS enabled Phone?
Phone is Nokia 6600 slide. And laptop(Dell) has F10 installed.
ADVERTISEMENT
Networking :: Connecting To Internet Using GPRS Modem With WVDIAL?
Apr 11, 2011trying to connect to the internet using wvdial but facing problems. the command runs fine until i get PID ppd Carrier detected. Starting PPP immediately.
--> Starting pppd at Sat Oct 23 10:40:09 2010
--> Pid of pppd: 2520
nothing happens after this.. I checked the resolve.conf and it is empty. i put openDNS server addresses but still did not work.
Fedora Networking :: O2 Mobile Broadband (Huawei E169 HSDPA) - Internet Loads At The GPRS Speeds Max Of 5kb/s
Dec 26, 2009I have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?
View 2 Replies View RelatedUbuntu Networking :: GPRS Internet Via Samsung Phone?
Aug 8, 2010I have a Samsung phone (S3310) and I'm trying use it as a modem to access the net on 10.04. I set up a Mobile broadband connection (under network connections) and I'm pretty sure the settings are correct because it works on a Nokia phone with the same service provider.
When I plug in my Data Cable and set it to Samsung PC Studio mode, my phone isn't detected as a modem. I just tried wvdialconf and it says "No modem detected". I'm guessing that maybe I'm missing some drivers here. what I can do get the phone detected as a modem.
Ubuntu Networking :: Connect To Internet Through GPRS Phone Via Bluetooth?
Feb 23, 2010How to connect to my Mobile Phone which have GPRS. I want to connect Via BLUETOOTH. Becoz I dont have any Data Cables.Plz give me the instructions to connect to my Phone via Bluetooth to access Internet.
View 7 Replies View RelatedNetworking :: Internet Sharing Using Edge / GPRS Modem & LAN / Router
May 18, 2010I use Opensuse 11.2 & Edge/Gprs Modem to connect Internet.I configured /etc/wvdial.conf & /etc/resolv.conf. Now I can connect Internet using this command "wvdial MYNET" in terminal.Now I want to share my internet using Lan card & Netgear Router. If i connect my PC with Router using wire & change option ON BOOT find this device in ifup then it'll show in ifconfig command.
My Router IP : 192.168.0.1 & It gives my PC an IP automatically : 192.168.0.2
I can ping my router.. even I can browse Router Admin page in browser. No problem there.But now If i want to connect my net using wvdial command... net connected... but no data passing!!! If i disable Lan card in ifup then Edge/Gprs net connection again OK!
Fedora Networking :: 12 Connecting To Internet?
Apr 15, 2010I'm using ADSL modem (not router) and I can't connect to internet. The network manager and the pppoe-setup command doesn't work. So I'm asking some of the experienced users of fedora 12 to help me setup my connection.
Details: ADSL modem with pppoe connection (working fine on win xp)
Fedora Networking :: Connecting To The Internet On Any Computer In The LAN?
Mar 4, 2009I recently set up a network of computers via Ethernet, all of which use Fedora 10. I would like to be able to get any computer on the network to hook up to the internet.(I think the solution is now figured out - see below, on page 2, "problem solved")
View 14 Replies View RelatedGeneral :: Connecting Nokia 6233 To Gprs In CentOS?
Jun 1, 2011I want to connect my Nokia 6233 mobile phone via bluetooth to GPRS in centOS 5.My system is running with P-IV processor.Operating system is centOS.
View 2 Replies View RelatedUbuntu Networking :: 9.10 Not Connecting To Internet At Home But Connecting From Work
Feb 9, 2010I just installed Ubuntu 9.10 and its great. However when I connect to the internet at home it shows that the connection has been established but I still cant connect to the internet. My flatmates are all able to connect. However, I am able to connect from work both wirelessly and through an ethernet cable.
View 2 Replies View RelatedFedora Networking :: Wired Networking Not Connecting In 12 With Windows Internet Connection Sharing?
Jan 16, 2011I just want to use Internet Connection Sharing (ICS) to connect to the internet. I have done a massive amount of troubleshooting, but some of it seems to contradict itself, and the only two things that I know for sure are that it used to work, and that my Ethernet cable is not the problem. When I use Terminal utilities like ifup and dhclient it seems that it can not determine IP information, but when I try to put it in manually, the "Apply" button grays out right after I finish typing it in. When I try to connect normally, in KDE or GNOME, the icon acts like it's connecting, then instead of having the connected icon, I receive a notification that "the network has been disconnected", and it goes back to the disconnected icon.
Oh, and by the way, I know that I could probably find a workaround, but I have limited resources, and this used to work. The Linux is a Dell desktop with Fedora 12 and the Windows is a Windows 7 HP laptop.EDIT: I hope that I didn't mess something up, but I accidentally used system-network-config to try putting in the IP address there, and ended up changing it back to the original settings, but the computer is now calling it Auto Ethernet in the taskbar icon, although sudo iwconfig in the terminal still calls it eth0.
Fedora Networking :: Connecting Linksys WUSBv2.8 To Internet
Dec 3, 2009I am trying to connect my desktop to the internet via my Linksys wireless usb WUSB11v2.8 adapter. My network showed up in the Network manager as soon as I installed Fedora and it asked for my network key, but it still doesn't connect. It just keeps asking.I was reading that possibly the driver is not compatible with the OS. I heard about RPMs and the ndiswrapper program that supposedly is supposed to help with compatibility issues so I went and installed both via a direct ethernet connection.
I guess my question is now since I have these programs, what else do I need and how do I go about completing the installation? I pretty much need to be baby stepped by step into how to do this including the best place to install the software, what files do I need, and where and how if I even need to get my device's chipset.
Fedora Networking :: How To Update Kernel Without Connecting To Internet Directly?
Sep 28, 2010I recently installed F13 on my Toshiba Satellite C650. It has a buggy ACPI which no linux distro till date supports. I got that covered though. But my problem is that the ethernet port works only if the kernel is >=2.34. But F13 came with 2.33.
I do not have an access to a wireless network. Please tell me how to update the kernel without connecting to internet directly. I am new to Fedora. I have been using Ubuntu for some time and this can be achived in ubuntu by downloading the DEB packages and dependencies.
Fedora Networking :: Share A GPRS Connection?
Apr 25, 2009I have two Desktops. Both running Fedora 9 and connected to each other with a crossover cable. I have a GPRS connection via a USB bluetooth Dongle. I can connect thru rfcomm on Kppp. Assigned static ip's 192.168.10.1/2 and can ping from one computer to the other. So far so good but now I want to share the internet connection between the two computers and run into a maze of gateways and DNS and iptables and am spinning around with no clues. Some of the things I do not understand are
1. What gateway does one assign when your computer directly connect to the internet through a GPRS and not through a NIC or router??
2. When I try to load the shared NFS folder, why does it say "could not load the location: internal error"?
3. Is there somewhere I could get a step-by step instruction??
Fedora Networking :: Sharing Bandwidth Using Gprs Modem In FC11
Aug 9, 2009i want to ask a question. sometimes i use a gprs modem to connect to the net. the gprs modem uses the usb port. i've connected this pc to another machine through crossover cable. the problem is that when there are two active connections, firefox can't load anything. also how can i share the gprs modem with my other pc that is connected via crossover?
PS. in my active network connections it shows:
eth0- the NIC
and auto eth1 - the gprs modem
i have also tried to change the firefox preferences but to no avail.
Both my computers run on FC11.
Ubuntu :: Internet In Pc Using Aircel-gprs Facility?
Jul 28, 2010iam using an aircel connection in my mobile and i was able to use its pocket internet facility in my pc using windows operating system.but when i tried it in ubuntu9.10,i was unsuccessful.iam using NOKIA 6600 and it has been connected to the pc using a bluetooth dongle as my phone has no usb connection facility.when using ubuntu 9.10 bluetooth was automatically enabled in my pc.In terminal window i typed the following commands
"sudo hcitool scan" and my phone was detected as
"12:12:12:12:12:12 NOKIA". then i typed
"sudo sdptool browse 12:12:12:12:12:12" and i got the result as
"failed connection to sdp server on 12:12:12:12:12:12:connection reset by peer".
Networking :: Connecting LAN PC Through Internet?
Mar 31, 2011I would like to connect a PC (it has no white IP) through Internet. It's possible to create tunnel with SSH, but I need more easy way. May be there is some service exists (like TeamViewer), so people can just run simple command on that PC?
View 3 Replies View RelatedNetworking :: Connecting To Internet On Ret Hat 5
Aug 16, 2010Am not able to browse on Linux 5.please provide me step by step procedure to config internet on my Linux 5
View 3 Replies View RelatedUbuntu Networking :: Connecting To The Internet On 9.10?
Jan 19, 2010I'm running Ubuntu 9.10 Live CD and I can't connect to the internet. I click on System --> Preferences --> Network connections and under the tab DSL I click Add. After i fill the information I click to connect to the new connection and after a while it shows me a baloon which says "Wired network: Disconnected - you are now offline".
View 1 Replies View RelatedNetworking :: Connecting To Internet Using Wvdial?
Jul 29, 2010I am trying to connect to Internet using Wavecome modem with Airtel GPRS connection. I am able to successfully connect and browse the Internet using wvdial. But if I use pppd, I am getting the error message as "LCP Terminated by peer".
The exact error I am getting is pasted below.
[root@pscu1320 ppp]# pppd call gprs-wavecom
GPRS modem init: press <ctrl>-C to disconnect
Wakeup Modem
[Code].....
Networking :: Strangest While Connecting To The Internet Ever Seen?
Apr 5, 2011I had an ubuntu 10.4 box, I used it mainly for programming, virtualization & other stuff. I've installed this box about 1 month ago, working on it everyday. About 2 days ago problem appeared when I just opened up firefox for cheking my E-Mail. I typed : [URL]. & nothing appeared & I just seen the famous firefox page when a networking problem is around . I just wondered and checked the connectivity & the wire itself, but find no problem around them, while playing with firefox I just had a turned on virtualBox machine (Windows XP service Pack 3), I just checked the internet within vm & working fine, I checked my e-mail from vm (windows xp), I thought restarting the system might help to solve the problem but damn, problem didn't solved & still arounds Well, I searched through websites dedicated to linux networking & forums that might help, I did anything that faced to my brain , follow another people recipes but problem did't solved for about 3 days ! Playing with primary & alternative dns didn't help, I did my best about solving the problem, disabling ipv6 from both linux networking settings & firefox itself didn't help also . After that, I thought reinstalling the linux might help to solving the problem, but install a new version of ubuntu, 10.10, I tried it, install it but the holyshit problem still arounds ! I think this might be a bug on ubuntu distro, I tried Mint 10 & the same problem, reinstalling x64 version of fedora core & the same problem .It's interesting that the same settings for TD-8101G TP-Link working fine for my Windows XP, Windows 7 x64 & the problem is arounds just for my linux distros .As I said I checked the internet for the problem & found nothing workable for me. I thought it's better to describe the problem & maybe another people faced with that problem .
View 9 Replies View RelatedCentOS 5 Networking :: Not Connecting To Internet
Feb 27, 2010I have a CentOS server that I can connect to over my local network. The computer I'm currently on is on that same network and can access the internet. My server can not connect to the internet. The network card is obviously connecting to the network since I can access the server locally with SSH or HTTP. While in the terminal for the server, I type wget google.com and the server can not find the specified host, so this leaves me to believe it can not access the internet.
View 2 Replies View RelatedUbuntu Networking :: Connecting To Internet In Campus?
Jan 22, 2010I have a problem which is connecting automatically to my spwireless. On my windows, my schools provide me the disc which contains several .cer files and a automated batch files to copy the .cer files to the root folders. I can choose to use the other network but in using that, i have to manually connect compared to using the spwireless. Anyway, my problem is that, how do i add the .cer files and to where so when i connect to the network it will look there for the cert. Because when i manually connect, only one cer can be chosen.
View 2 Replies View RelatedUbuntu Networking :: Connecting To Wired Internet In 9.10
Feb 21, 2010I have a problem connecting to the internet using Ubuntu 9.10 . But the same works fine in Ubuntu 9.04.. First I thought it was my hardware problem and asked my friend(also was using ubuntu 9.04) to try ubuntu 9.10 but he too failed to connect....
I have an wired ADSL Modem given by my Service Provider. When I switch on my modem the router gets connected but it cannot connect me to internet...
Ubuntu Networking :: Connecting To Internet Via LAN / What Is GATEWAY?
Jun 19, 2010Whenever i used to setup a new connection in Windows it would just ask me User name and password here i need to fill up something called as "Gateway" !? The connection won't be accepted unless i fill up something in there... So, what do i put in there? I'm on a LAN of 3 computers connected with a router.The router takes one wire as input from the modem(cable).
View 9 Replies View RelatedUbuntu Networking :: Connecting To Internet Through Another Computer?
Dec 23, 2010I'm trying to get internet to my old server through a laptop. The laptop is running ubuntu 10.10 and the tower is running ubuntu server 10.10 X86.
View 1 Replies View RelatedUbuntu Networking :: Wireless Not Connecting To The Internet
Feb 16, 2011i have a Levano S10e intel atom preccessor and the net-book is not connecting wirelessly to the network. i have tried at two locations and even plugged in a exterlal wifi adapter. it wouldnt connect then either, the only way to get connected is to use a cat5 cable. here is the ifconfig output with no cat5 inserted and it not connecting to the internet.:
[Code]....
Ubuntu Networking :: Connecting To WPA Internet Using Terminal?
Apr 27, 2011I need to reinstall my GUI but all I can access currently is a terminal, I have the encryption key and SSID but have found all the how to's I've read really confusing since following certain steps on them give me error messages, I'm connecting wirelessly to wlan0.
View 9 Replies View RelatedNetworking :: Connecting To Internet When 3G Modem Plugged In
Apr 25, 2009I was recently asked to get a 3G ZTE 633 modem (not in stores) to connect to the internet whenever it was plugged in. I had it successfully working on my Ubuntu Gutsy Gibbon machine but it does not work on Fedora 10 which is where it is required to work. When the 3G modem is plugged in I use a Udev rule to run usb_modeswitch which changes it from being in usb storage mode to being in modem mode. This part works fine. I then run a second udev rule (on the modem device), this should run a script which connects to the internet. Unfortunately it falls over here. The script does run but it will not connect. However if I run the script manually from root it works fine. I guess that it is a permissions issue.
The device permissions are:
crw-rw---- 1 root uucp 188, 0 2009-04-26 11:31 ttyUSB0
crw-rw---- 1 root uucp 188, 1 2009-04-26 11:31 ttyUSB1
crw-rw---- 1 root uucp 188, 2 2009-04-26 11:31 ttyUSB2
The script and script folders permissions are:
drwxrwxrwx 2 root root 4.0K 2009-04-26 11:46 .
drwxr-xr-x 23 root root 4.0K 2009-04-26 11:13 ..
-rwxr-xr-x 1 root root 95 2009-04-26 11:46 run_internet
One thing to note is that there are three udev devices associated with the modem. They are ttyUSB0, ttyUSB1 and ttyUSB2. I use ttyUSB2 to talk to the modem when connecting. Here are the files. If you require any more let me know:
The first udev rule:
SUBSYSTEM=="usb", SYSFS{idProduct}=="2000", SYSFS{idVendor}=="19d2", RUN+="/usr/bin/usb_modeswitch"
The second udev rule:
SUBSYSTEM=="usb", SYSFS{idProduct}=="0031", SYSFS{idVendor}=="19d2", MODE="0666", RUN+="/outputs/run_internet"
The script:
#!/bin/bash
/bin/echo script
/usr/bin/wvdial &
cp -f /etc/telstra_resolv.conf /etc/resolv.conf
The wvdial config file:
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = ATS7=60 S30=0 S0=0
Init4 = AT+CGDCONT=1,"IP","telstra.internet"
Modem Type = Analog Modem
Baud = 9600
New PPPD = no
Modem = /dev/ttyUSB2
ISDN = 0
Dial Command=ATD
Phone = *99#
Password = user@bigpond.com
Username = password
Stupid Mode = 1
So what am I missing? I suppose it is related to device permissions. Why does the "mode" command not work? With what rights do udev rules run?
Networking :: Connecting To Internet With Serial Cable?
May 4, 2011I have a vista computer that is connected to a router via a ethernet cord. The router is connected to the internet.I have a computer installed with Debian that does not have a ethernet port in the back of it. Is there a way that I could connect my Debian computer to the internet through my vista?
View 5 Replies View Related