Fedora :: Can't Mount Host On Local Network Via Nsf?
Sep 21, 2009
I have two machines on my local netowrk, one running Fedora 9 and the other Fedora 11,(64 bit version).I made one, machine A, into an NSF server and arranged to export a directory to the other machine B.I made sure the firewalls were allowing nsf traffic, and I restarted all the relevant daemons.But the mounting still doesn't work.I looked at the setup on my Linksys router, but I don't see anything obvious there that might be getting in the way.ping and ssh recognize my names for the two machines and work properly, bu t I've also tried using the numeric local ip addresses.I tried with the program showmount on B to see if there was any connectivity and I getB% showmount -e Aand I get the responseclint_create:RPC: Port mapper failure - RPC: unable to receive.I used to manage a departmental network and set up nfs mounts all the time, but things were simpler then. I am at a lost what to look at next
View 14 Replies
ADVERTISEMENT
Oct 12, 2010
I am mounting a Window's network shared folder every time Fedora boots. It is mounted into the /mnt directory. Recently I noticed I am almost out of disk space, and I found out that my mount folder is what is eating all the space. I was under the assumption that the mounted folder wasn't on my Fedora machine at all, and resided on the Windows machine. Apparently my assumption was incorrect, or possibly I mounted something in an unusual way.
View 2 Replies
View Related
Mar 9, 2010
I have a mac and an openSUSE box connected wirelessly to a router. From my mac, if I ping the Linux machine by both ip address and hostname "elmo.local", I get a response. If I ping my mac from the Linux machine using its ip address, I get a response. However, if I ping the mac from the Linux box using its name "kermit.local" - nothing!
This means in order to share files between them via the network, I have to use the ip address rather than name, but I'd rather not. When I had Ubuntu installed instead of openSUSE this all worked fine out of the box, so I'm assuming it's a problem with the setup of openSUSE rather than the router or the mac.
View 4 Replies
View Related
Mar 26, 2011
basically i am able to connect to my other windows machine using rdesktop I want to be able to mount the window machine's partition (particularly my media folder cusermyaccountVideo) i know rdesktop ipaddr -r disk: blah blah blah mounts the partition onto the local machine however, i cant figure out what the specific commands are i tried followings but with no luck
Code:
rdesktop ipaddr -u username -p password -r :c=mntmntpoint
rdesktop ipaddr -u username -p password -r :c=mntmntpoint
rdesktop ipaddr -u username -p password -r :cmyaccountVideo=mntmntpoint
all these commands didnt work do anyone know how to do this? i thikn there must be a way
PS: no luck with smbfs as my machines arent on the same lan network (not sure if samba can connect remotely)
View 7 Replies
View Related
May 6, 2010
I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this:mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000.I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has?
Mount the remote samba with multiple groups on the local system?Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs.which runs through gvfs; but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. And the last solution would be NFS but that means that I have to synchronize the uids and gids on the local system with the ones from the server.
View 1 Replies
View Related
Jan 11, 2011
I am trying to host a local website(an wiki application) within a network. Is it necessary that all the files I need to upload should be in the var/www?
View 8 Replies
View Related
May 13, 2011
I made a script to backup file from each host with general password in local network. This script using SSH Pass and Rsync with this
syntax:
rsync --rsh="sshpass -p password ssh -l root" hostath destinationpath
Everything is okay under 9.10 version until I migrate to Ubuntu 11.04, there is always give an error:
rsync error: received SIGINT, SIGTERM, or SIGHUP (code 20) at rsync.c(541) [Receiver=3.0.7]
I am using bash version: GNU bash, version 4.2.8(1)-release (i686-pc-linux-gnu) and 2.6.38-8-generic kernel
View 3 Replies
View Related
Dec 11, 2010
I want to install Globus tool kit it says host name is not FQDN(fully qualified domain name) I tried by installing DNS but it doesnt works
I got the configuration. I have posted in following link. I am not able to reply your post i dont know why. [URL]
View 1 Replies
View Related
Mar 19, 2011
I have a computer, the one I am on now, with Ubuntu 10.10, it should be completely updated... and I can network with other computers, I can access Windows XP and 7 shared locations on other computers, and I can also get Ubuntu on other computers to access this computer's shared files.What I can't do, however, is share my hardrives that are on this computer, I have tried sharing them in /media/ and etc, but it is not working, apparently you have to mount them in some mystical way.
Another problem is getting Windows machines to access Ubuntu computers on the network - which I believe is a Windows problem, so I can figure that out some other time, but importantly, I want to be able to share my hardrives over the network.
If someone can give me some instructions to mounting and sharing hardrives(internal), and even my DVD-Drives, and portable USB devices, would also be fantastic - since, in Windows you can just right click, "share", and it's done.. It is a very useful thing to have, and I don't want to use Windows on this computer anymore, but I have no choice, really, if I can't share my storage to the other computers.
View 4 Replies
View Related
May 10, 2009
I want to use single label host names on my local LAN, without using any domain (at least no registered one). My machines should be named in a fashion similar to 'myserver', 'mydesktop' etc. so that i from a browser on any LAN machine may write 'http://myserver', and get the webserver on 'myserver' (so NO domain part, e.g. myserver.domain).
Do i need to create a DNS zone for each host or is there a way to put all host in a single zone, if so; which? Would such a name be considered a root domain?
View 4 Replies
View Related
Mar 31, 2011
I installed a new disk and need to share it on NFS, but the share keep failing. I think the reason is the disk was not mounted when NFS started. How do I guarantee local disk mounted before NFS?
View 2 Replies
View Related
Aug 2, 2010
I was trying to figure out how to get my network drive to mount as a local drive on my computer. This was back on 9.10. Since I've upgraded to 10.04, my boot process halts and tells me (paraphrasing) /shared is not ready to mount. To continue, pres S to skip or M to manually mount the drive.
Well, I have it mounting now through GVFS and I don't need this in my startup anymore. Frankly, it's just annoying that it won't boot into Ubuntu right away. So, what's the startup file I need to edit to remove the attempt to mount the network drive?
View 1 Replies
View Related
Sep 3, 2010
I am trying to share directories between two F12 machines on a local network with a router box doing DHCP because not all machines on all the time. Web access is fine and local ping and ssh works but telnet doesn't. I have never succeeded doing mounts. So I have been searching for things to fix the above and have just tried rpcinfo. If I do this :
rpcinfo -p 192.168.2.2 it gives rpcinfo: can't contact portmapper: RPC: Remote system error - No route to host. Does that suggest that actually there is an installation problem? So I tried "yum provides portmapper" and that gives "No Matches found".
View 14 Replies
View Related
Jun 22, 2011
I am trying to access a DVD mounted on a machine running Fedora12 (192.168.0.105). I thought this should be possible with NFS, but the above error message is what I keep getting, no matter what I try.
Here is my mount command:
Code:
mount 192.168.0.105:/mnt/dvd -t nfs /tmp/scaleo
The Fedora 12 machine has the NFS server running, and the corresponding entry in /etc/exports is
Code:
/mnt/dvd *(ro)
I thought this might be a firewall problem, but it persists even if I turn firewalls off on both machines (client as well as server.) Also, doing
Code:
ssh 192.168.0.105
is OK, so what is wrong with the route?
I am trying to access a DVD mounted on a machine running Fedora12 (192.168.0.105). I thought this should be possible with NFS, but the above error message is what I keep getting, no matter what I try. Here is my mount command:
Code:
mount 192.168.0.105:/mnt/dvd -t nfs /tmp/scaleo
I now tried
Code:
mount 192.168.0.105:/mnt/dvd -t nfs4 /tmp/scaleo
and it seems the mount succeeded. So, instead of nfs, one must write nfs4?
View 9 Replies
View Related
Apr 1, 2010
I have Fedora 12 (Fedora-12-i686-Live.iso) installed and booting in a VMWare workstation (version 6.5.3). I am able to login as the LiveUser.
I need information on how to access the drives on my host which is WindowsXP. My C: on the host is shared, and my network adapter for the VM is "NAT".
The only directory listed in my /mnt directory is "live".
My Fedora enviornment is "bare bones". There is nothing installed except for the original files from the "iso" loading procedure.
I also have been unable to get the VMWare tools installed, and I don't know if this is related. I don't mind bypassing this if this isn't required. My only desire right now is to access my C:
View 6 Replies
View Related
Feb 6, 2010
I run a headless Ubuntu 8.04 server, which acts as a web, email and file server. I am sticking with 8.04 as it is a LTS release and will upgrade to the next LTS when it is released.
I have two external USB drives, that I need to mount at boot. I have been using /etc/fstab up until now, with the following entries:
Code:
However, as I gather from doing searches is quite common, occasionally I get an error during boot (causing the system to drop to a recovery shell) because the USB drives take time to wake up and the system hasn't found them by the time it reads /etc/fstab.
From doing searches, it seems there is nothing you can do to fstab to fix this, so you need to mount them using an rc.local script instead, using:
Code:
The problem is, as I have two USB drives, their /dev/sdxx location changes between boots. I thus want to use UUID codes as I do in fstab, however I haven't found anything about this.
Does anyone know how I can use the mount command and UUID to mount a drive in rc.local and what options I have to use the mount the drive with the same options that I am using in my fstab entry? Obvisouly, I can't refer back to fstab using the mount command, because then I will still get the boot error issue if they are listed in fstab. And there is no space internally for the USB drives as there is already two internal drives.
View 3 Replies
View Related
Mar 28, 2011
I just updated Fedora 14 with the updates it downloaded and I am now stuck with the error.
View 10 Replies
View Related
Jan 27, 2009
The internal network is behind nat done by the PC Router.The TP Link is recieving wireless signal from outdoors and it has switching and basic routing capabilities. I'm using the PC router for better routing options.PC Router (or R for short) is a triple-booting machine - Linux, FreeBSD and Windows. It has two lan cards - external (ext_if) - 100Mbps Realtek 8139 and internal (int_if) - 1Gbps integrated Realtek 8169.The problem is that all traffic from R to the network is slow - about 5-20K, while the traffic in the oppoiste direction is all right - about 10MB that is fine for 100Mbps cables, NICs and switches. The problem persist no matter the OS the pc R is running.I've tried some debugging on the situation as follows:
- put another PC at the place of R - everything is fine. That exclude the possibility of damaged cables, RJ-45s, switches and etc.
- connected both of the NICs to the Internet while the internal network is being disconnected and they both work fine (no delays)
- traffic shaping is not running
- there is nothing in firewalls except NATing the internal network (and it is working fine). Actually these firewall rules have been operational for more than months and everything was fine untill a week or two ago.
- changed the internal NIC with another
- connected the internal network directly to the TP and all of the PCs are getting good network performance. Then connected the R machine to the TP as well and there was good performance between the internal network PCs and R.
- R has good performance to the TP. In fact everything has good performance directly to the TP (when not connecting trough R).
- the problem persist only between R and machines from the internal network.
View 2 Replies
View Related
May 16, 2010
I'd like a way to see all of the devices on my local network and what their local IP address is. I recall that I used wireshark to troubleshoot a similar problem a while back, but it doesn't seem to have a way to see all of the devices- only the traffic. (I'd like to do this without having to physically interface with my router if possible, and I am in an encrypted network if that matters)
View 6 Replies
View Related
Jun 28, 2011
I have installed a web server on my local network. Everything is well configured and web pages are shown correctly from Internet (outside the local network) using the domain or the public IP.The issue is if I try to see that web pages (using the domain or the public IP) from inside the local network. In that case the router config page (192.168.1.1) is shown instead of the web pages.From inside the local network I'm only able to see the web pages using the internal IP address (192.168.1.XX).
View 2 Replies
View Related
Feb 3, 2009
My Windows guests see my VMware Host Only folders as \.hostShared Folders But when I try to see them from a Linux guest, all I get is frustrated. No permutation of that seems to work. Because the Windows guests see the shared folders I know the host is doing its part in providing them. After two days of not finding an answer on the VMware Workstation forum I finally figured out that the problem really is how to look for them with Linux. With Linux I can turn off all NICs accept the Host Only NIC, put smb://172.16.138.1 into the address bar and see all the shares on the host, but not the folder designated as the host only folder.
View 3 Replies
View Related
May 31, 2011
I am having difficulty sending files from a remote machine to local one using
Code:
scp
. It is working the other way however. local > remote. I am using the verbose options
[code]....
View 3 Replies
View Related
Feb 7, 2011
I've successfully compiled a local gcc(s), but now I want to have multiple versions (which is easy enough), but one in particular, I want to be 32-bit. This one eludes me.
Can anyone suggest what to do in order to compile a 32-bit version of the gcc that I want? All the other versions, 64-bit, compiled no problem.
View 3 Replies
View Related
Oct 3, 2009
I'm a new Fedora 11 user and have an ATT U-verse setup. Where can I find help on how to get the box on my wireless network?
View 5 Replies
View Related
Nov 23, 2010
I've been always used to install fedora on my server this way : i put the fedora boot images on a pxe server, i copy the fedora install dvd to a ftp server, then i set the path of the dvd copy in the netinstall process.
But since a couple of release it doesn't work anymore, it keeps asking me for files in /repodata which doesn't exist on the dvd.
Is there any simple way to do this ? I tried cobbler using the dvd source, it create the repo fine with the proper files but it's too complicated, i just want the damn files.
View 4 Replies
View Related
Apr 28, 2011
I want configuration a DNS server for my area! What DNS server software is better than other software?
View 4 Replies
View Related
Sep 27, 2010
I'm using Windows XP. I'm connecting to a UNIX box using putty SHH(ksh). Now I want to copy a text file present in remote host to my local system.
View 5 Replies
View Related
May 25, 2010
I've got an Ubuntu server hosting our websites and other various things here in our own home. We recently switched to a router that doesn't support loopback (abomination), so I've set up hosts files on our computers so we can access our own sites when on our home LAN.
However, we often take our laptops as we travel about, and I'm guessing due to the hosts files when we try to access our sites, it'll look on whatever local network we're connected to for our server, which won't work, obviously.
Is there a way to set up something like a hosts file that'll only try to look up the local IP of the server when we're on a specific network (our home one), or have one that tries to look for the local IP first, then proceeds to try and resolve the domain name and use the external IP if the local IP doesn't work?
View 6 Replies
View Related
Jan 6, 2009
I've tried, but now I give up. I'm trying to run Apache on FC9. Nothing fancy, no extras, just the default installed apache. [correction, I have coldfusion installed, however the service is not running] I've set the Listen variable to every combination I could think of, with no success. I can set it whatever I like (such as my local IP) on any port other than port 80. If I try to set it to 192.168.x.x:80, it gives me the error message:
Starting httpd: (98)Address already in use: make_sock: could not bind to address 192.168.x.x:80
I've run netstat commands to try and find applications listening on port 80 and found nothing. Whenever I chose a port other than 80 to get the service to start successfully, I am able to serve pages locally. But even with my ports forwarded correctly, no one outside the local network can see it. I've checked with nmap that my machine is opening the ports and even cheated, disabling the firewall during testing to ensure it was not part of the problem.
I noticed while locally nmaping my server that whenever I set Listen 192.168.x.x:8081, 8081 is opened, as well as normal port 80. When I stop the httpd service, both those ports are simultaneously closed. Why is httpd opening port 80? I'm assuming this is related to why I cannot assign Listen to port 80. If I run remote scans from sites like www.nmap-online.com and www.canyouseeme.org, nmap-online will report filtered on ports 80 and 8081 if my httpd is running, and if httpd stopped, 80 is closed, filtered 8081.
Can you seem reports success on ports 80 and 8081 if httpd is running, fail if httpd is stopped. I'm sure thats all a lot of information cluttered in to all that. To summarize, I cannot start my httpd server on port 80, and I cannot ever see my webpages beyond my local network. Am I missing something extremely is simple and I'm just over looking it?
View 5 Replies
View Related
Aug 3, 2009
As the title says I'm trying to build myself a local RPM mirror. I have multiple laptops and a desktop that use Fedora 11. So I used 'rsync' to setup and sync my directories. I next went on to create my repo with the 'createrepo' function. I run my server backend as FreeBSD so I moved my data over there and setup my 'lighttpd' service.
Everything went fine until I used 'rsync' and synced up my data. Am I supposed to run 'createrepo' after each sync? If so, does anyone else use the same kinda setup, even if not FreeBSD, but a different os other than linux for their server that they run this from? I've been dealing with this for 2 weeks now and finally gave up researching and testing and thought. Not something I'm good at doing. Check my register date and my first post date.
Edit: FreeBSD doesn't have a port or unofficial port for this. I noticed it seems to be written as a python script so thought I could somehow get it to run on FreeBSD with linux emulation.
View 7 Replies
View Related
