Debian :: Can't See Gui On New 5 Install "frequency Out Of Range"?
Jun 5, 2010
I am having troubles with my old school monitor though.Upon boot up I can press CTRL+ALT+F1 to see a text only screen, but CTRL+ALT+F7uses my monitor to say "frequency out of range". I googled and found that I can press CTRL+ALT+"+" to change the X.org resolution. If I do this about five times I finally see a screen. However, the resolution must be too high because in order to see other parts of the screen I have to "scroll" with the mouse off the edges of the screen. Furthermore, if I go to System->Preferences->Screen Resolution, Resolution and Refresh rate are blank
Got a new HP Mini 210 the other day and things run pretty good using squeeze considering how new it is. The only serious problem is that the available scaling frequencies are mis-reported by the system. Instead of 800, 1.0, 1.3 and 1.6, only 1.0 and up are shown.
acpi-cpufreq is installed and run properly on boot, indeed the system scales nicely from 1.0 through max as needed / dicatated by the ondemand governor. Powertop tells me it spends 99.8% of its time at the "lowest" frequency of 1.0.
In the hopes that a newer kernel would solve things I downloaded 2.6.34-1 and built it, and though it runs very nicely it doesn't solve the problem of the missing 800Mhz frequency. At this point I'm at a bit of loss as to how to proceed. I've asked the same question on the Debian mailing list, because I want to give this the good old college try before submitting a bug report to the kernel mailing list.
I certainly do not consider myself a Debian power-user, but I do presently have 3 Lenny systems and 1 Squeeze system running fine in my home on "older" hardware. However, for the past week I have been trying to get yet another system running, and I have hit the wall. This is on a new home-built system with an AMD Athlon II X4 and an ASUS M4A785-M motherboard. The Lenny installation was done with a net install of the AMD64 variety.
I always get a "Monitor frequency out of range" error whenever I boot. I can do a CTRL ALT F1 to get to command line, but I have no success getting to GUI. I have read numerous posts of similar monitor frequency problems with various distros, and most point toward HorizSync, VertRefresh, etc settings in xorg.conf. I have played with a myriad of options there, but I still get the "frequency out of range" error after a reboot. I have swapped monitors to no avail (monitors that work on my other Debian 32-bit systems). I really don't think the problem can be the xorg.conf file, since I have tried the exact same file as on the other machines. (Also, those systems seem to be more than happy without custom HorizSync and VertRefresh options in their xorg.conf files.)
On this new computer, I am using the motherboard's integrated video output (theoretically a ATI Radeon HD5200).I don't know if special options are needed in xorg.conf for this???I am able to successfully boot to GUI with multiple differentCD Linux distros; however, no such luck with the Debian installation. I would prefer to stay with Debian if possible, but I cannot live by command line alone on this system.Please let me know if there is something else that I should try before punting and moving to another 64-bit distro.
I've recently reinstalled a computer with 10.04 for my parents to use, and it worked fine at mine, but after transporting it to theirs and hooking it up to their existing monitor it doesn't seem to work anymore!Well, it boots and I hear it login but I don't get a splash screen and at some point between the bios and the login sound it comes up with Frequency out of Range. On the warning message it displays a frequency of "72.9 kHz / 90.2 Hz" but in the monitor settings its reporting that its operating at horizontal 64,0 kHz and vertical 60.0 Hz. I also don't get any splash screen when starting up, just a flashing _ before the monitor stops things
What I can do however is drop into a the tty console (alt+ctrl+1) and login to the shell but don't really know what things to change from there.Having googled things a bit I've found references to xorg.conf but there's no such thing on my system so I can't edit that to fix this. Likewise I also have found references to fiddling with grub to get into the recovery, but grub doesn't even appear when I boot and I don't know what to press to get it to drop into its menu...
This is really urgent as I need to go home tomorrow at the latest and I want to get my parents system working before then. I also have no spare monitors here and I didn't think to bring with me a liveCD to fiddle with things (only a UNR netbook which I'm posting this from), so the console is the only access I have to the machine.Some specs: Ubuntu 10.04. ATi Radeon 9100 IGP, no proprietary drivers are installed. The monitor is an old CRT that still works beautifully and whose replacement is not an option.
I just updated my Wubi install of 9.10 to 10.04 last night. Everything went well until it required me to reboot the computer. I rebooted, loaded Ubuntu from the startup list, and then the screen went blank and I got "H.V. frequency over range" on the monitor.
I can load the GRUB options, but recovery mode using the most recent kernel does not work. I am entirely unexperienced with using the terminal and command prompt options.
Here's what I have attempted so far:
$ sudo dpkg-reconfigure xserver-xorg this did not do anything, the command was not recognized
$sudo nano xorg.config I don't even know what to do when I get to this screen
I've been having this problem ever since I updated the kernel version and reinstalled the video drivers. It happens after grub and before I log in with my account.I know it wasn't a resolution related problem due to the fact that I had a compatible one set last time (I don't really think 1024x768 has any problems with my monitor), and the only thing left to modify is the vertical and horizontal refresh rate, and for that I tried running:
Code:sudo dpkg-reconfigure xserver-xorgas some forums/threads pointed, but it just returns a blank line and nothing happens (the threads were quite old since I couldn't find anything recent so I suppose it's outdated). So then, what do I do to reconfigure X? X.X
After a fresh install of debian 5.05 over net it boots then at end of text lcd screen shows out of range. if start in single user then startx it goes out oif range. How can i set it to a range monitor can do?
when installing debian LXDE faced with a challenge - exceeded the frequency of the video (the monitor goes off and a menu appears with the words "video frequency exceeded"Tell me what to do for a successful installation? (Debian has been downloaded through the site LHDE.org)Video card (POWERCOLOR HD4670 AGP)
Question: Installation had me entering my password many times, seemed like for most everything I did during install & setting up the desktops. It was a little frustrating compared to what I was used to with Ubuntu. I know this frequency will reduce once settled in although Linux and "fiddling" go together so some will continue. When using Ubuntu I was able to set that up to bypass some password need, not all. I was hoping there are options for that with Debian but my efforts all day yesterday failed to find any. I am not looking to eliminate password use entirely and I don't expect it to be just like Ubuntu either, however...
My main areas of frequent password use that are new to me with Debian Squeeze are:
1)All partition mounting. Using Ubuntu I edited fstab using a tool called "Storage Device Manager" so that only myself, not "users", had full read-write access to all partitions at boot time. However, none of those fstab codes or any new ones that I tried seemed to work in Squeeze. Besides Squeeze, I have two ntfs and one ext3 partition to access. Example: my music files are on an ntfs partition and I have to enter a password to listen to music.
2)Opening a root nautilus folder. In Ubuntu I made a custom application launcher with "gksu nautilus" and that gives you a no-password one-click access. In Squeeze, I enter a password every time.
3)Reboot & Shutdown. This one surprised me. Every reboot or shutdown requires my password unless I logout first but that adds a step. It may have something to do with a second desktop I installed (kde), I'm not sure. I tried making a script linked to an application launcher that runs "init 0" but that asked for my password too.
I'd like to be able to do 1,2 & 3 above without password entry other than maybe at the main log-in.
About me: This is my first post here, and am trying to be courteous. I checked the DebWiki, Google & this forum for answers. I found a little about ntfs partitions and saved it to a file. My situation is a Debian beginner but using Ubuntu for 7 or 8 months. My technical skills are mid-range. I use Debian on a newer dell laptop with Intel chipset and Intel CPU, triple booting Windows 7, Ubuntu 10.10 and Debian-Sqeeze-di-rc1-amd64. I installed using DVD #1, and made a local repository with DVD 1&2 and added a second kde desktop. Gnome Debian is my favorite now, it runs very well and will probably replace Ubuntu as my primary OS. Everything works that I can tell, except the Software Sources GUI does not load but I go into the source.list file and edit it manually.
I have both cpufrequtils and acpi-whatevercpu, normally processor would be correctly controlled by the ondemand governor and have two steps for frequency, 1.4 and 3.5GHz. Now I've noticed my frequency is always at 3.5GHz, cpufreq-info gives me the hint:
Code: Select allguiu@guiu-desktop:~$ cpufreq-info --cpu 0 cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org.
[Code].....
This isn't really a big issue. Normally the processor will sit at +-28°C at low load levels at maximum frequency, with the proper governor it will drop to +-20°C (room temperature) and lower. So I still would like to get proper management of frequencies for more hardware life, and better energy efficiency, not to mention quieter fans. Documentations on cpufrequtils is very broad, and apart from that I don't know where to look for this. Debian wiki page mentions about a file that can be used to configure this but there isn't much documentation.
Ps: I previously had this issue where acpi-cpufreq driver wouldn't load at all, this is due to setting on bios resulting in different frequencies than stock, trying to get default frequencies allowed the driver to work.
I have a problem with CPU frequency at overclocking.Normally the processor is clocked at 2.7 GHz (13.5x200), Debian detects it correctly. When I overclock it (in the BIOS of course) to 3.3 (11x300), BIOS at booting shows everything correctly.
I want to plot a set of data in only one plot.The problem is that some points of the data should be better plotted in a linear scale (lets say 0 to 100,000) but there are other data points that, exceding the value 100,000, would be better plotted in a logarithmic scale, as they goes in the range 100,000 to 500,000,000. Let's say the data is:
Code:
X Y 0 100 10000 80 20000 75
[code]....
Is there a way to plot all these points in the same plot in only one X-axis showing two different ranges in that axis: linear: 0-100,000 logarithmic: 100,000 - 1,000,000,000?The axis would be read, for example, as:
I want to turn off frequency scaling permanently and totally in the lowest-level way possible. Is there a kernel command line that can be used or is recompiling the kernel without the governor stuff the only way?
Solved. Just modprobe -r and blacklist the acpi_cpufreq kernel module.
I want to build a bash script, which can ping a range IP adresses which will be filled in by the admin. If there is no IP-adress filled in, then the script must ping the subnet where the system is logged on. So if my ip is 192.168.1.6, then the script must ping from 192.168.1.1 till 192.168.1.255 Or else, if there is given a beginning and ending ip it must ping that!
The first part of the bash script is to ping a given range (see below). But there is one problem, how can I tell the script to ping from $begin till $end, [..] is of course wrong! But what must be filled in there???
echo "Enter beginning IP-adres:" read begin echo "Enter ending IP-adres:" read end ping -c 1 $begin [..] $end
The second part is to find my own ip and ping the whole range.. How to do that? I only can find my own IP, but I cant ping the whole range,, how to do that?
Not sure this is the right place and I feel really stupid for asking this but, I want to change the frequency of the online update checks but, for the life of me, cannot find out how. During install, I can configure it but I now want something different. I thought that there was a topic with yast under software but no. Only "online update" which basically give me manual update. I click on configure but same screen appears.
I have a suspicion that this is easily fixed, however a good google (and this forum) hammering having turned up the fix. So I probably have the wrong search criteria, My Gnome Applet for switching CPU Frequency Scaling has 'disappeared' and is not listed in the the Add to Panel.. list of applets.
I am running a VPN (Juniper Networks client) and an ifconfig shows me that its opening a tunnel and also adding routing instructions (I think). Anyway the problem is that when I'm connected to the VPN, I lose route to all my local machines and this is getting annoying when I want to use ssh.Does anyone know how to not route a certain range of IP's through the VPN?
I have been trying unsuccessfully to load Debian on my desktop. I have tried both live and otherwise. Both AMD64 and i386. It seems to be loading fine and then all of a sudden the monitor quits with a sign Input signal out of range. I have tried lots of other live disks and they have worked fine. My monitor is a Hanns G and my video card is NVIDIA GeForce8200. All other stuff very normal. 4 Gigs of RAM. What?
i just did a graphic install of debian lenny and when i finished the installation and restarted the computer the grub boot menu appeared and i selected debian and nothing happened the monitor just displayed a message saying "out of range" i have a dell studio xps 1800is it my graphics card (it shouldn't be) how do i start x server in a different resolution (if screen resolution is the problem
How would one block an IP range access to a Debian-based Linux system for say 47.1.1.1. - 48.255.255.255? Would it be with the hosts.deny file? If so, how would it be written in the file? Also, would the system require being restarted for the changes to take effect, after writing to the file?
My last Linux install was SUSE 6 on an early ISA based Pentium clone. I'm used to Unix / bash from OS X, MinGW, QNX & BeOS... none of these rely heavily on X. But I'm thinking that Linux is so popular, I'm doing a lot of my Windows stuff under MinGW, why not just stick Linux on and be done with it.So I've polled the various distros, I'm a power-user / dev so Ubuntu doesn't seem like me, and I'm not familiar enough with Linux to go Gentoo just yet, but the way I slim Windows and OS X installs down to just what I need. I love apt-get and like FreeBSD installs I've seen, but want some Linux kernel goodness for my self, so I have chosen Debian.
I grabbed the amd64 build of lenny DVD 1, partitioned up and installed a bare system that I can apt-get the bits I want later.Here's the problem... When the install completes rebooting sends the graphical login to a frequency my old Hanns-G TFT can't handle.I can Ctrl-Alt-F1 back to the terminal or boot in single user mode, and everything seems to be good until you go GUI.Here's what I've tried.
I've renamed /etc/X11/xorg.conf to /etc/X11/xorg.conf.oldI ran dpkg-reconfigure xserver-xorgI've reinstalled using both simple GUI and Expert GUI using both kernelsI've tried adding nvidia-* packages with apt-get and aptitudeI remember there used to be a frequency tuner app for SUSE 6 and XFree86, but it seems that sort of thing is depreciated in modern Linux.Info? My GFX card is an nvidia GT 220, the motherboard is an ASUS P5QL Pro, the Monitor (Hanns-G) is attached via RGB HD-15 D-Sub (sadly that's all I have access to right now) and it's native resolution is 1280x1024 4:3 @ 60Hz, but in heXPee it will sync at that resolution at 60, 70, 72 or 75Hz, though it does get fuzzy at 75Hz.I'm fairly certain that X is working, just not at a frequency my screen can display... how can I fix this from single user, or regular bash terminal?
---edit--- Forgot to mention I ran dpkg-reconfigure on the XServer. :s It didn't offer video drivers, only to change from gb 105 keyboard layout and ps/2 mouse. I set the META key to the logo key while I was there, but it wasn't really helpful in any other way.
I have up until now been able to use the add-apt-repository command without issue but right now it keeps returning an IndexError.
The error is below:
Code:
Select allx@y:~$ sudo add-apt-repository ppa:/kilian/f.lux Traceback (most recent call last): File "/usr/bin/add-apt-repository", line 122, in <module> shortcut = shortcut_handler(line)
[Code] ....
IndexError: string index out of range
I have tried using the command with an empty ppa (just sudo add-apt-repository ppa:) but that comes with the same error. Googling the issue only brought up some bugreports of a month back, and I've used the command with success a few days ago.
I am running an AMD Athlon 64 with an NVIDIA 6600 video built into the motherboard (PC Chips). My monitor is a 19" LCD with a standard VGA connector. I tried installing Lenny and everything went smoothly. However, when I rebooted, the monitor said "Signal out of range." I had this happen with a live CD of another distro too.
I am currently running Debian 6. I would like to know if there is a way and how i would go about blocking a certain IP range from connecting to my server within a certain port range. Say for example.
i want to block ip range 123.123.123.* from connecting to my server on the ports 33000 - 43000. But, i want to allow them to connect on any other port range, and i want to be able to allow connections from my server to the blocked ip range on those same ports. so, blocking incoming only on the above port range.
I have tried installing the ATi drivers via the 1-click install process, however when I get to init 3 and try to run sax2 (sax2 -r -m 0=fglrx) my monitor just goes out of range. I have tried this in both OpenSuSE 11.1 and 11.0 - both the same. I have tried running sax2 with the -l switch for low resolution - no change. I have also tried the switch "--vesa 0:800x600@60" and "--vesa 0:1024x768@60" which are known resolutions/requencies that this monitor supports (the latter is the native resolution) - no change.
I have tried another monitor but it's exactly the same. My video card is an ATi Radeon HD2600AGP and is correctly identified by OpenSuSE, and displays video fine using the default driver.
Installed CentOS 5.4 x86-64, installation is fine. First bootup after install always fails (after a few messages are displayed) with my monitor showing an "out of range" message.I know exactly what to fix (sync values in xorg.conf) and what values to enter there, but what I can't figure out is, how to get to a stupid prompt! Or a smart one for that matter.Also, I do get a message (before the "out of range" message) from CentOS, telling me to "press I for interactive startup" - but all that does is print as many "I" on the screen as I press. And did they really mean "I" and not "i" for this?
I hear great things about CentOS and if you can help with this silly question - How to get to a prompt - as easy as it probably is for you all, it would help me a lot.
