Debian :: Sparc Install But Then Can't Open Boot Device?
Apr 25, 2010
I JUST registered here as I have not used Linux in several months. Linux and I have been and off and on relationship, but after I realized Ubuntus limitations Ive pretty much only dealt only with Debian (on PPC as well as x86, and also some Suse on x86).
Anyway, so I just picked up a couple Sun Ultra 5s for free. One had 256MB RAM (4 x 64MB), a 4.3GB IDE HD (no SCSI in the Ultra 5), and booted fine in Solaris up to the login screen at which point it wasnt really any use to me since I dont know the login name or password, and really want to run Linux anyway. The other I am told needed a firmware (chip?) and basically didnt do much more than power on. However, it had a 40GB HD and 2 x 128MB RAM modules. So, I replaced the 4.3GB drive with the 40GB, and replaced 2 of the 64MB RAM modules with 2 128MB modules, for a total of 384MB RAM.
BTW, both machines have the 270MHz Ultra1 CPU. Anyway, I used my main Windows x86 machine (which Im on now), downloaded the Debian SPARC net install, and burned it to a CD. Put the CD in the Ultra 5, installation proceeded nicely, though with one disconcerting message stating the urgency of which a reboot was required (though still telling me to wait for installation to finish). I mean, the whole installation process basically went perfectly except that one odd message.
So, when install is complete, I choose finish installation, the machine reboots, ejects the CD, and then ultimately get a message saying "cant open boot device". I am very new to Sun hardware, and am by no means an expert to Linux. The only thing Ive really tried so far is to type "boot hda" which only causes the same message to appear.
From previous experience, I have written on paper the info for all of my partitions. So I think my Debian install is sitting there waiting to be utilized, but the Sun hardware is oblivious to the fact that theres a perfectly good OS on the machine yearning to be booted.
View 4 Replies
ADVERTISEMENT
Feb 7, 2011
I am an intermediate linux user. However, I know nothing about solaris. I am trying to install Debian Sparc on a sun blade 2500 workstation. I was told it should work. I am able to go through the debian installation process but when the box reboots it does not boot into Debian. I have now gone through the debian install process several times and now it saids there are too many primary partitions. I tried a rescue install but it saids there are no partitions installed on disk? What am I doing wrong? I am curious if I need to pass a specific argument at the command line to boot into silo? I cannot find any relevant guidance online about this problem and I cannot believe I am the only one to stumble here.
View 1 Replies
View Related
Jan 18, 2015
So the other day I installed Debian Wheezy on my Sun Blade 150. While the OS is installed fine, all the webkit based browsers continuously crash after a few pages. So, I tried to download IceWeasel since it wasn't installed when I tried installing Debain off the DVD. The only problem is, it won't install as the Xulrunner version it requests is xulrunner-24.0_24.5.0esr-1~deb7u1_sparc, however the only version available on the repositories is newer. Is there any way to get the older xulrunner version, or is there going to be a fix for IceWeasel soon on Sparc?
View 3 Replies
View Related
Feb 5, 2011
So this also happened to me when trying to install an old version of Ubuntu (hardy I believe). I have a Sun Netra X1 that I am trying to install the latest stable Debian Sparc64 port on. I'm doing a TFTP boot, and am able to get the kernel to load. However, once the kernel loads the installer, the screen gets garbled (attached is a screenshot from my console session) This server has no graphics card, so I have to install using the serial console. I don't recall having this issue when I installed the last stable version. Any ideas what's going on or how to fix it? I even passed the option "DEBIAN_FRONTEND=text" to the kernel, but it didn't seem to do anything.
View 2 Replies
View Related
Sep 12, 2014
I installed Debian Jessie (netinst, daily snapshot) on my Acer Aspire V5-123 laptop in the UEFI mode with the secure boot turned off. everything (network, hardware, partitioning, ...) went smoothly to the last step, but after removing the boot media (USB stick) and rebooting, the firmware could not find the boot device ! The only thing I can think of, is that the EFI boot is not set up properly by Debian installer, but I don't know how to fix it.
View 11 Replies
View Related
Oct 21, 2010
I have been trialling Slack 13.1 on a spare 32b system for a couple of weeks, and today I took the plunge and put it on my main machine. I completely re-partitioned the drive (using the Slack disk) and installed Windows7 on one partition and Slack 13.1 on another. The install worked fine and I tested that it boots from LILO into both Windows and Slack perfectly. I then ran:
slackpkg update
slackpkg install-new
slackpkg upgrade-all
And since then it fails to boot with the following:
Code:
VFS: Cannot open root device "802" or unknown block(8,2)
Please append a correct "root=" boot option; here are the available partitions:
0840 488386584 sde driver: sd
0841 97659103 sde1
0842 19535040 sde2
0843 498015 sde3
[Code]....
I have seen many, many similar problems when searching Google but they all seem to be caused by different things.
View 8 Replies
View Related
Apr 16, 2011
Reboot and select proper boot device or insert boot media in selected boot device and press a key. I got this error after: Reducing my Windows 7 partition by about 100gb. Creating a new partition (100gb) and copying my Ubuntu partition (10gb) to the new partition. After it was copied, and pasted, the original partition was deleted. I now had two partitions a new 100gb Ubuntu partition and a 600gb (or so) Windows 7 partition.
All of this was done using a bootable USB with Ubuntu 10.10 and GParted partition editor. Now when I boot I get the "Reboot and select proper boot device or insert boot media in selected boot device and press a key." error.
View 9 Replies
View Related
Jun 7, 2010
I am using a kernel with no initrd. I have had this kind of panic before. Usually it means that the kernel can access the hard drive because the driver for the controller or filesystem isn't built into the kernel.
The kernel is 2.6.34 vanilla.
My IDE controller is a Silicon Integrated Systems SiS 5513, and I built the driver for it into the kernel BLK_DEV_SIS5513=y
My /boot (hda1) is ext2, and everything else is ext3
EXT2_FS=y
EXT3_FS=y
My grub entry (hda2 is my root partition) kernel (hd0,0)/vmlinuz root=/dev/hda2
View 5 Replies
View Related
Jan 21, 2010
i have a recicled sun fire v240 that i need to use for central loging server, i got an ubuntu 7.10 cd that i got to install succefully in the server. So foar so good, the problem now is that i cant install any software, everytime i run apt-get update the error says:
[Code]...
I guess the old repositories configured in the old 7.10 iso are no longer valid, where can i find a valid one?
View 1 Replies
View Related
Jan 25, 2010
I install Debian on a Power book g3 and i need the right click function. I try mouseemu but it give me an error: open: No such file or directory No uinput device found! Make sure the uinput module is loaded or CONFIG_INPUT_UINPUT is compiled in kernel. if there are other way for the right click function?
View 3 Replies
View Related
Mar 3, 2010
Without going into a lot of the reasons, I have a bootable program on a USB stick that i would like to 'boot' when debian is starting up (or after it completes, or whenever it makes sense to do it). My MB does not support a USB boot, I've removed the floppy and CD so I can add additional HDs (its a small box but well ventilated).
Another option I have is to use my bios 'network boot' option, but I have no clue how to use it and the only description in the mb manual says "Allows system to be booted over a network" In network boots, *usually* one is given an option of specifying a device address, and the network boot executes a boot protocol (e.g. bootp), and the boot image file is downloaded to the target, stored and run out of RAM. No evidence of this behavior is exhibited when the network boot option is selected in the bios...
View 2 Replies
View Related
Apr 13, 2010
All my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?
View 3 Replies
View Related
Jun 11, 2011
I rebooted my server and out of nowhere the RAID5 array won't assemble. I've tried everything I could think of to reassemble the thing. I fear that the array is ruined, but I can't imagine how. Here are various bits of information: The simplest failure (with and without partition numbers, which have not been needed in the past):
Code:
richard@nas:~$ sudo mdadm --assemble --verbose /dev/md0 /dev/sd[bcd]
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/sdb: Device or resource busy
[code]...
View 5 Replies
View Related
Jan 29, 2011
I'm using Debian kernel 2.6.32-5-amd64 I have this little nit picky problem when I re-boot, my webcam and my Tv card switch around on video0, video1 and video2 if my usb webcam is plugged in at boot. I would like to keep it plugged in all the time and have it on video2 and my TV card on video0 and video1. I had read where maybe setting up a udev rule might accomplish what I want to do I just don't understand how.
Here is my camera info from lsusb:
Bus 004 Device 002: ID 046d:08d7 Logitech, Inc. QuickCam Communicate STX
Using v4l2ucp gives me this info about my hauppauge hvr1800 TV card:
Driver cx23885
card Hauppauge WinTV-HVR1800
bus_info PCIe:0000:03:00.0
capabilities 0x05010011
View 1 Replies
View Related
Jul 11, 2010
When I boot off of Debian Kernel 2.6.26-2-686. This is what happens. It stops at attached scsi generic sg5 type 0 After 4 or 5 minutes it comes back and says.
Gave up waiting for root device. Common problems Boot args (cat /proc/cmdline) Check Root= (did the system wait for the right device) Missing modules (cat /proc/modules; ls /dev Alert /dev/sdd8 does not exist dropping to shell /bin /sh: can't access tty; job control turned off If I boot off Debian Kernel 2.6.26-2-686 (single user mode) Then use Control-D it boots fine.
View 1 Replies
View Related
Mar 23, 2011
I am trying to figure out what needs to be done to automatically set read/write permissions for everyone for my proprietary USB device on system boot. I have created a udev rules file which changes the permissions for the device when it is connected, but it does not change the permissions when the system is booted with the device already connected. The file looks like this:
SUBSYSTEM=="usb_device", SYSFS{idVendor}=="our vendor id", MODE="0666"
Does something else need to be added to the rules file to make it work when the system boots with the device connected? Is there some other script which needs to be created somewhere?
View 1 Replies
View Related
Aug 2, 2010
After asking on both this forum and the Fedora forum, I felt it was safe enough to install a copy of Fedora on my working-well openSUSE drive. I have a 1 TB drive, partitioned as follows:
I did an install of Fedora 13, was VERY careful to set up the installer to put it's files in the partitions I wanted, although I did let it mark the partition as active, feeling it may have to boot during the installation process.
I had grub installed in the root of the partition rather than the MBR for both systems.
When Fedora finished installing, I rebooted the system only to find that it wouldn't. I got the dreaded "No Boot Device" message.
So, I started the 5 hour process of booting with the parted magic disk, booting with a Gentoo live disk (only one around), monkeying with the install parts of the openSUSE and Fedora disks, swapping drives to Windows to download openSUSE Live CDs (yes, both) and searching the forums and various other web sites for some poor bloke who did the same stupid whatever it was I did, and finally, as I was using fdisk on the Gnome Live CD, I noticed the warning message stating that fdisk would not work on a drive that was partitioned with the GPD format.
Notice that I have 5 partitions? That is not a typo on my part, I used the GPD format when I set it up so I could do what I did without using "imitation" partitions.
When I used parted (the command line editor on the Gnome Live CD) to change the active partition, everything started working again! Well, at least I can boot the openSUSE system, the most important thing.
It is my suspicion that the Fedora install uses fdisk to do it's work, and fdisk just mucks up a GPD formatted disk. Not the information, just the part of the drive that holds the partition table. Perhaps just the flags section. I don't know enough to say with any certainty.
I didn't change the drives parameters during the installation of Fedora, so I don't know of it even offers the GPD partitioning option. If not, I can understand how this sort of thing could happen.
Still....So now all I have to do is make the grub menu, the one installed with openSUSE, boot the Fedora installation on the next partition. Seems simple enough.
View 4 Replies
View Related
Feb 13, 2015
I'm inexperienced in Debian. I have a dual-boot machine (64-bit, Debian 7.3, Windows 7, legacy boot) and encouter a problem at boot ever since I completed the installation of Debian 7.3 alongside the exising Windows 7. This machine has six hard drives: two are intended for ntfs storage of general data (raided together by RAID1); two more are intended for ext4 storage of general data (also raided together by RAID1); the fifth contains the Windows OS files and the sixth contains the Debian OS files. The problem is that I arrive to the grub_rescue each time at boot, seeing the message:
GRUB loading.
Welcome to GRUB!
error: no such device: e081517b-3399-4067-9294-8f0686f753ca.
Entering rescue mode...
grub_rescue>
View 2 Replies
View Related
Jan 17, 2016
How to boot debian on an RK3288 based device (that isn't a chromebook?). Been trying to do so myself, but to no avail.
The closest match to my device is this one in the sense that it uses the same SoC - an RK3288. However my device is not a chromebook; instead it is called an "RKM MK902II". Unfortunately I cannot find any information on how to boot this device (it does have a micro sd card slot it can boot from, though I'm guessing it needs some sort of bootloader to be written onto a micro sd card in a specific way, but how!).
Interestingly the device I have is running some sort of version of ubuntu. Though how it boots it is an absolute mystery!
I've tried searching around on the 'net for a while now and apart from a script and a few "distros" distributed as image files, I can't really find anything at all. Looking for info about this device or RK3288 chipset?
View 8 Replies
View Related
Nov 14, 2009
Currently running rc2. Downloaded 11.2 final DVD, md5sum is good, burned DVD, YaST says media check is good. (And for completeness burned a second DVD and get the same problem.)
On booting from the DVD I select "Installation" - a kernel loads and starts checking available h/w devices then crashes with the above message.
Followed by Please append a correct "root=" boot option.
Tried with root=sda1 (partition that is /) and only change is unknown-block (0,0)
My best guess is that I have EXT4 (did a clean install of RC2)? And/or I dont have a swap partition?
View 1 Replies
View Related
Sep 26, 2010
Ubuntu 10.04.1 to prepare a USB flash drive for use as installation media for a new computer that's on the way. When the Linux kernel tries booting up on the flash drive, I get an error saying VFS: Cannot open root device "<NULL>" or unknown-block(8,1).Here's how I got to this point...Created bootable partition on the thumb drive.Put the following files onto the flash drive: initrd.gz, vmlinuz, and ubuntu-10.04.1-server-amd64.iso fromhttp://archive.ubuntu.com/ubuntu/dis...ages/hd-media/Install Grub2 to the drive via grub-install.Put the following into boot/grub/grub.cfg:
Code:
set timeout=120
set default=0
[code]....
View 9 Replies
View Related
Jan 18, 2011
I had Ubuntu installed, i installed Debian and there was no dual boot. So i formated all the hard disk to install only Debian. It installed but at boot i get error: no such device and the grub rescue> prompt. i googled for a solution and nothing worked:
- i tryed reinstalling grub, not worked
- i did the windows cd fixmbr trick, not worked
- reinstalled debian with fixmbr the first step and nothing
- tryed deleting with dd the mbr, not worked
- reinstalled grub from debian rescue, not worked
what should i do? i can't access my computer? please tell me how should i fix it? the google guys will kill me because i put their servers on fire
View 14 Replies
View Related
Jun 20, 2011
I've installed squeeze and wheezy on an old Toshiba Satellite 210 CS laptop with 48MB RAM and a 20GB IDE harddrive.Grub2 won't boot at all and stops with a "error: cannot allocate real mode pages". The solution to that is to use the grub-legacy package.The boot then fails with "waiting for root device" and drops to an initramfs shell.
View 5 Replies
View Related
Nov 21, 2010
I have 2 Debian OS's and wanted to put Fedora next to it.
Install went ok, but after rebooting it says: "No root device found. Boot has failed, sleeping forever."
During install from the live CD I didn't "v" the boot (efi or something?) because I thought Grub would take care of everything.
Should I just reinstall again and choose the Fedora bootloader? Won't it mess up Grub?
View 14 Replies
View Related
Apr 24, 2011
I am trying to install Ubuntu 10.10 from a USB flash memory stick. It works fine until around 95%, where I get the following warning/error:
[Code]....
I click OK and the installer seems to finish nicely, except the terminal throws several errors along these lines (see photo):
[Code]....
I tried also with 10.04 LTS, the difference being that the install warning appears two or three times instead of once. Some results from googling (Ubuntu Forums, Ubiquity bug) suggest unchecking the initial update options. I am going to try this but I'm not sure if I'll be able to get the boot loader right (there seemed to be problems with this).
View 7 Replies
View Related
Jan 13, 2010
There is no prompt for choosing whether I boot windows or Linux it just takes me to Linux. I need to install and load some things from windows and can't figure it out.
View 1 Replies
View Related
Mar 5, 2016
I am having a problem with my new Toshiba Satellite Laptop... I had installed debian for some time but last week suddenly stopped working.
- the computer stopped working at all... nor bios access.
- I did a new bootable installation in USB drive and downloaded the latest debian iso from official website and created the bootable device via dd as usual.
- I installed the new debian but after I removed the usb drive in order to boot into my new system. I was taken to a screen saying "Start PXE over IPv6 -- Start PXE over IPv4 ..." I followed several links looking for a fix, and all of them lead me to disable network boot option in BIOS setup...
- I disabled but after that it appears a new message "No Bootable device -- Press restart system" and nothing happens from there.
- I have found info in Internet regarding this issue, but all I find is "windows related"
- Someone recommended me this: "The BIOS can no longer recognize the hard drive as a bootable device. This could be for a number of reasons. Your best bet, if it is still under warranty, is going to be to bring it back to where you purchased it"
- But instead, what I did was to create a new bootable device, this time containing XUBUNTU and installed it to the machine, I had the good news that the installation proceed without any problem, so I could figured out that my machine it is still alive...
- Back to my issue and hoping that something unexpected happened that fixed the machine, I got back and did a new Debian bootable device, also hoping that the latest was corrupted or something, but after reboot to my new system... the problem persisted again.
- I chose to have 1 partition in full disk.
Now I don't know what else to do... I don't like ubuntu, I have used debian for some years and I want to keep using it and I would not like to be forced to move to ubuntu or xubuntu for this.
View 14 Replies
View Related
Jul 16, 2010
Everything was working fine with dual boot sda/osuse 11.2 and sdb/kubuntu. Decided to install new 11.3. Lost dual boot, can now only boot to 11.3, sort expected that. I see the root and home partitions in Dolphin but can't mount or open them? Would like to access the files copy to Osuse. Rite clik get me "error permission denied" I can reinstall Kubunt and it will set up my boot loader correctly with grub2, but is their a better quicker way? Why does Osuse still use the legacy grub?
View 5 Replies
View Related
Jan 25, 2011
can someone direct me how to install Ubuntu as a dual boot on my open suse 11.2 I could not find any installing instructions. if someone could give me a link or direct me ,
View 5 Replies
View Related
Apr 4, 2011
I am new to opensuse, having migrated from Ubuntu. I have had some difficulty with power management on Ubuntu so i decided to install opensuse with kde as i heard it was good for laptops. I have had lots of trouble getting opensuse 11.4 to boot properly and to run without freezing.
I have trawled the forums and bugzilla and the documentation, e.g. SDB:ATI - openSUSE and SDB:Configuring graphics cards - openSUSE. Consequently i am now able to boot (normally), however whenever i open any application, e.g. Dolphin file manager, Firefox, etc, the tab starts to load (little circle starts spinning on the tab), and then it freezes.
At this point I can exit X Windows and enter the text mode. I have repeated this with the FGLRX and Radeon drivers running. This is always repeatable. I can also boot into level 3 and do things there.
My computer details are:
HP Pavilion dv6 3032TX
Processor - Intel i7 720 QM
Ram - 6GB
GPU - ATI Mobility Radeon 5650
Harddrive - 640GB 5400rpm
[Code]...
What i have tried so far:
1. First 4 steps on SDB:Configuring graphics cards - openSUSE
2. Install and run FGLRX
Note that i cannot failsafe boot - it never boots into X Windows and just hangs. I really do like the look and feel of opensuse and would love to use it, but at this point my only option is to try another distro.
View 3 Replies
View Related
