I upgraded my MB, CPU and memory to 4G. I am running 32 bit Lenny. In the BIOS, I see about 3.8G memory. However, in Lenny I see only about 3.2G. Is it normal? Is there something I need to do to get the most out of memory this size, like setting highmem?
View 8 Replies
Today I installed Lenny on a new server. The server didn't have any CD-Rom, so I tried putting the net install on a memory stick using unetbootin. The install went fine, but the problem was that the memory stick became sda and two SATA disks in the server became sdb and sdc.When I then tried to remove the stick, the SATA disks became sda and sdb, and it would not boot, because it had written the MBR on the stick.It hurried a little bit, so I had to take out a CD player from another computer, and connect it inside the server to get Lenny installed.But it would be cool if it was possible to install with the stick. And no more waste of CD-Rom players that will be used only once.
View 1 Replies View RelatedHow do I write a script for my Linux that can show me total memory vs used memory and have it email me results if it's over 70 percent?
View 2 Replies View RelatedI've got this issue for past week.
Mysql Crashes with 111 error although it starts back up instantly.
but i can't seem to figure out why.
-Server Is Deb. Lenny + Direct Admin.
Quad Core 2.5, 8GB Ram.
-Mysql ver 5.3
-Htop shows mysql is most of the time using 33 - 50% CPU.
(the init.d name is /etc/init.d/mysqld )
-This is from the err log of last crash. code...
i was trying to use gnome and kde but i don't like them. I tried xfce and it seem to fit my needs but.My computer is used to be powered on for a weeks. While time passes, a process xfdesktop begin to use more and more memory and to free RAM i need to log out and log in again.
I tried squeeze yesterday on my virtual machine and it has 4.6 and seem not to have that bug, RAM usage is static(yes it still works when i write this and have memory usage 34492k, which is not changing for an hours of usage already), also 4.6 is MUCH better than 4.4.
i already tried adding squeeze to "sources.list" but i can see too many dependencies which should be upgraded if i install 4.6, i'm beginning to afraid it can crash entire GUI(or entire system, i can see there is libc6 required to be updated).
So I'll try to be brief and to the point here: I've got a couple of C / C++ apps that communicate with one another via shared memory. These worked completely fine until.. well, about twenty minutes ago when I finished making some network card changes and suddenly, I've got a weird problem going on. At one point, Parent app waits for Child app to set a boolean indicating it's finished initialization. This worked fine the last time I ran this app up (a few days ago). But right now, the shared flag never seems to get triggered (I've added a printf("Waiting..."); in Parent app until the flag is set). All the code leading up to it being set in Child app seem to be running smoothly, so I tried spitting out the addresses of the shared memory locations. The addresses mapped by Parent app and Child app are different; this seemed odd, so I went back and wrote a simple miniature app that just opened a shared structure on my own box, and I get the same thing - different addresses - but the miniature apps work just fine.
Is it normal for a shared memory space to be mapped to two different addresses across two processes?
If so, does anyone have any idea what might be the issue at hand with my Parent / Child app scenario? The Child creates the shared memory, the Parent has a wait before it opens it, and if it doesn't exist should fail (opening with PROT_READ | PROT_WRITE)... it doesn't fail so it's evidently there.
All of this worked until literally just a few hours ago and I made some changes to my network cards, and I can't even imagine how that could have changed whether or not shared memory mapping worked...
openSUSE 11.2 installed on machine with 5GB memory but System Information in KDE desktop shows only 3GB total memory. Just added a further 4GB but no change shown in System Information.
Is there something I must do to have sysinfo report true value and does this mean that memory not shown is not being used?
POST BIOS check shows 9GB installed.
I'm trying to meter my memory usage. When I use these different programs, they all show me using different amounts of RAM.
View 2 Replies View RelatedI normally use a very lightweight Linux setup. No desktop like Gnome or KDE, just Icewm as the windows manager and nothing else that normal users might consider essential. Well, I do need a file manager - I use Thunar.
Recently I've been trying Gnome. Whenever I shove a memory stick into a USB port, or connect my digital camera, it can automatically pop up a file manager showing all the goodies on that device. KDE does this too. I like this. Although quick at the command line, I like not having to go sudo to mount the device and all that.
If I want to stick with a lightweight setup using Icewm+Thunar, is there something non-huge I can install to make external devices fire up a Thunar window, or otherwise make access to the contents brainlessly easy?
that I have 2 users? It says "2 users" I only have one account ... whats up with that?
View 4 Replies View Relatedi do have a strange problem get running php5 on lenny 64 inside apache2. i had installed it as all instructions on the web does: # apt-get install php5 libapache2-mod-php5 php5-cli php5-common php5-cgi
apt has enabled php automatically, so
/etc/apache2/mods-enabled/php5.conf does have inside:
<ifmodule mod_php5.c>
AddType application/x-httpd-php .php .phtml .php3
AddType application/x-httpd-php-source .phps
</ifmodule>
[Code]...
is it save to install linux kernel 2.6.35.2 on Debian Lenny 5.0.5 or stick with automatic updates...
View 14 Replies View RelatedI have added a 10 Mbps network card to my SGI O2 MIPS workstation running Debian Lenny running the 26-2 kernel. The workstation already has an onboard NIC which is working fine.(eth0).
lspci -v shows ths card as:-00:03.0 Ethernet controller: Compex ReadyLink 2000 (rev 0a) Flags: medium devsel, IRQ 18 I/O ports at 1800 [disabled] [size=32] Upon googling I found out that this card is an NE2000 clone. I downloaded the latest 2.6.36 kernel sources and did the following:-
1. Make Menuconfig
2. Loaded an alternate kernel config file (my working kernel config file)
3. In DeviceDrivers->Network device support->Ethernet (10 or 100 Mbit)
I selected ASIX AX88796 as the help associated with this showed it as an NE 2000 clone. configured it to be a module and did make, make_modules and make_install. Edited /etc/Modules to load ax88796 and added an alias eth1 ax88796 to this file. copied the new kernel to the /boot and did a reboot, the machine booted up fine and udev -r showed the 2.6.36 kernel and lsmod showed ax88796 loaded. But, Iam not able to bring up eth1 using:-
ifup eth1
The error messages given are:-
SIOCSIFADDR: No such device
eth1: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
[Code]...
I installed debian etch on my system. Installation done successfully, but when it boots up the X server is not starting and showing error. Note : It is perfectly working with debian lenny. Configuration : Intel DG41RQ ,1GB Ram ,160GB HDD.
View 1 Replies View RelatedAre exist any repository for debian lenny with games like nexuiz vdrift planeshift etc?
View 2 Replies View RelatedI could't find the 64bit Debian Lenny OS for Intel architecture.Hence I have installed amd64 and it is working fine.Does both intel and amd have the same 64 bit OS amd64 ?
View 3 Replies View Relatedi recently moved away from ubuntu (as they wouldn't let me change my gdm themes lol) i installed lenny usin the net install for ia86 but i cannot change my screen resolution from 1024x768 to my card/monitors native setting of 1366x768 i have included a .txt taken from the benchmark an profile gizmo which i hope rovide any of you with all the info needed (to be honest i don't understand half of it) my laptop is a fujitsu amilo li3710 with dual core, 3gb ram an 160gb hd an a intel gma4500 with shared memory graphics
View 2 Replies View RelatedI'm trying to install Debian/Lenny on a iBook clamshell. I couldn't seem to burn an install CD that the iBook would recognize, so I eventually copied the contents of the CD onto a self-powered USB drive and I can now get the iBook to boot off of that thru open firmware. However, when I get to the Debian installer main menu, it still won't read the CD, and apparently it does not have network drivers to install over Ethernet. Is there any way I can supply a driver for the ethernet interface (lspci reports that its a sun GEM ethernet interface) or somehow convince the installer to install from the content of the USB drive (which is a duplicate of what's on the installer CD)? Heck, if it'd be easier to get the Airport interface running to reach the Internet I'd be up for that too.
View 1 Replies View RelatedI have read tons of articles on how but none work. I have edited the source.list file with what they say and I have used all the terminal commands that are becoming very repetitive.
View 11 Replies View Relatedis there a way to auto login as root? login in window preferences won't allow me to select rootPS before anyone starts on the me bad, I'm a programmer using it on a closed embedded system, and need to link to others software, and need to be root
View 6 Replies View RelatedI read one release goal for wheezy which I had read few days ago, dnssec for wheezy.
[url]
Now the only thing I understood is this will make it harder for the bad guys to give any fake packages while I'm updating from a debian mirror .
Am I correct in assuming that ?
Also do I just have to install the autotrust package and wait for the dnssec-conf to be packaged and installed, correct ?
i have to reinstall my pc with a testing version. The installation almost is the same as stable version (lenny). But, the problem is that, i can't login it after the installation completed. The new user i created during installation is invalid! So, i have to enter the single user mode, to my surprise, the new user(i created before) doesn't exist! So, i add a user here.But, i still can't login to my system as the normal mode.How should i resolve such a problem?
View 4 Replies View RelatedI installed Debian Lenny on my old IBM thinkpad R40e but i can't change the brightness either with the Fn keys or with the brightness control debian has. i have searched around and it seems to be a problem with linux on IBM thinkpads but i don't know that much about this sort of thing so any help would be appreciated. if you need any more info then just ask.
View 9 Replies View RelatedMost of the time I rebooting, my resolv.conf is getting updated by resolvconf program, so the network connection cannot be reached. I followed this: Debian User Forums - View topic - Solving DNS problem (dhclient & resolv.conf)
View 7 Replies View RelatedCould anyone tell me how to get Debian Lenny to automount CDs the same as Ubuntu does i.e. automatically, with a Desktop icon etc.I've worked out how to automount CDs using autofs, which is OK, but it still doesn't seem quite as good as the way Ubuntu does it.
View 6 Replies View RelatedI have problem with loging, actually iptables logs a data but it seems that for some reasons does not writes in a log file:
Code:
iptables -L -v
Chain INPUT (policy ACCEPT 406 packets, 124K bytes)
pkts bytes target prot opt in out source destination
0 0 ACCEPT tcp -- any any xxxxxxxxxxx anywhere tcp dpt:xxxx
[Code]....
i checked /var/log/message and /var/log/syslog nothing is here related to iptables. then i create separate file for Iptables by adding this: kern.warning /var/log/iptables.log in my rsyslog.conf it does create iptables.log file inside /var/ but its still empty
I've found that I need to use pppoeconf, but it doesn't work. I have default Debian kernel with PPPOE module. After looking for the modem it gives me the following message:"Sorry, I scanned 1 interface, but the Access Concentrator of you provider did not respond. Please check your network and modem cables. Another reason for the scan failure may also another pppoe process which controls the modem."pppoeconf detected the interface successfully (eth0, I have only one interface), but doesn't work. It does, however, work with my router connecting without any issues.
View 4 Replies View RelatedUser familai with amd64 for computational chemistry and i386 for desktop. Seeking advice from users who succeeded in arranging a laptop with Debian squeeze or lenny, wireless LAN, 3D acceleration video, flash for speech. The laptop WITH STANDARD USA KEYBOARD should be available from European market resellers.
View 1 Replies View RelatedI am using a broadband internet connection. Currently I am using pon and poff commands to start and stop the internet connection respectively. But for these commands to execute I should switch to the root user. I want even a normal user to be able to start or stop the connection. How can I do this?
View 1 Replies View RelatedI have two pc's that I've recently converted to Lenny boxes, and I've noticed that whenever there's a lot of disk IO, one of my cores (both pc's have dual core cpu's) jump to 100%. Is this normal? They're both amd64, and I think both of them should be using the AHCI SATA driver.
If you need any more information about my setup, let me know.
