Debian Configuration :: WLAN Disappears With Upgrade Of Squeeze?
Feb 9, 2011
My version of Squeeze was about half a year old when I updated/upgraded it just now. As part of the (longish) process I was advised to run apt-get autoremove, which removed what looked like a stunning amount of material. As another part I noticed a huge number of error messages about nonexistent locale files (I think) whizzing by.
Well, the result has various cosmetic changes and no doubt fewer bugs, but it doesn't have WLAN. I used to see an icon at the top right like two tadpoles chasing each other, turning into a set of green (if I was lucky) or grey (if not) bars. No longer. No tadpoles, no bars, no error message, nothing.
This very recent thread ("Just isntall debian 6.0, wired networking ok but no wireless") looks helpful. However, I don't know what WLAN hardware I've got or how to get a text dump of this kind of thing. 4D696B65 kindly points the person who asked to wiki.debian.org/ipw2200. I don't know whether I have any of these "Intel PRO/Wireless 2100, 2200 and 2915 devices" but I'm encouraged to read there that [the file] is now also available in the nonfree-firmware tarball which we build regularly on cdimage.debian.org. Supply this blob on a CD/floppy/USB drive etc. and d-i will do the right thing. I don't know what either "blob" or "d-i" means, but I was rather hoping that some software or other would look at the hardware, look at the available firmware, and install accordingly (as happened months ago). So got the (small) file; I opened it up; I copied the contents to a CD (even though it's not an ISO). But apt-cdrom add is not interested.
View 14 Replies
ADVERTISEMENT
Feb 14, 2011
My net-book is working properly with Debian squeeze 2-6-32-5-686, only the wlan does not work. After typing lsusb I have got the message: lsusb : Bus 002 Device 002 : ID 160a:3184 VIA Technologies, Inc. VIA VNT-6656 [WiFi 802.11b/g USB Dongle]
So I obtained the driver package : VT6656_Linux_src_v1.19_12_x86. I followed the instructions ( make install... ) - but the result is only a lot of error messages. Mayby I am using the wrong driver package for the squeeze kernel - I don't know.
View 9 Replies
View Related
May 21, 2010
I installed squeeze and followed the instructions concerning b43-fwcutter and obtained firmware for my broadcom wlan interface. So my wlan worked for a while, but it just ceased functioning, for no obvious reason.
# lspci | grep WLAN
04:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
# dmesg | grep b43
[1.283080] b43-pci-bridge 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[1.283092] b43-pci-bridge 0000:04:00.0: setting latency timer to 64
code....
View 8 Replies
View Related
Aug 22, 2010
1) old a1300 laptop: P3 800, 256 MiB RAM, HDD, PC-CARD NIC. from lspci: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) with debian (i386), previously lenny, now squeeze. running as server.
[Code]...
Smaller files seem to transfer faster, but I have no idea why. I've checked with ethtool that both NICs are running at 1000Mb/s, and both are connected to the same Gigabit switch. The HDD in the laptop had previously provided (nfs) transfer speeds of 12-13 MiB/s. The options in fstab on the client are what I've changed them to since, while trying to fix the problem. Can't remember exactly what they were, but rsize, wsize and nfsvers are some I put there trying to fix it.
I had considered buying a new, faster HDD for the laptop, but that is certainly out of the question until this is resolved. Edit: Is this the right place to ask about this? I did wonder if the 'General Questions' category was a better fit.
View 1 Replies
View Related
Mar 2, 2011
I am running a server that has Etch on it. I have only recently been given this responsibility as I am the "IT-guy". I am running postifx, squid, shorewall, courier, samba and other things. The network has about 75 users with emails and data. I do not want to do anything that would risk their data and emails getting lost.
Is it still recommended that I upgrade to Lenny and then Squeeze?
View 4 Replies
View Related
Feb 18, 2011
I just upgraded from Lenny to Squeeze and now when I enter startx I get a solid black screen and the computer does not respond to any keyboard input. Ctrl-Alt-Backspace, Ctrl-Alt-Delete, Esc, Alt-F2, Alt-F4, etc. all do nothing. No beeps or anything. I have an NVidia graphics card and have been using the proprietary NVidia drivers. I originally thought the problem might be related to this driver but I tried both the nv and vesa drivers and got the same results.
Attached is my Xorg.log.0 file. It just ends after the GLX extension initialization.I am able to use ssh to login after running startx. Running "ps aux" from the remote machine I did not see a process for X. I copied the output below the Xorg.log.0 file.
View 12 Replies
View Related
Apr 17, 2011
I upgraded from lenny to squeeze on a notebook and I can no longer connect to the wireless network. The computer is an LG notebook and the network card is ralink rt2860. I am using Gnome and NetworkManager. The wireless key is WEP hex. It was working fine with lenny till before the upgrade. After the upgrade, the network card stopped working. So, I checked
$ lspci|grep Network
08:00.0 Network controller: RaLink RT2860
Then I reinstalled the driver with apt-get install firmware-ralink wireless-tools Then the network manager tray started working again and saw the network, but cannot connect. It was trying to connect but timed out and kept asking for the password. It is the correct password. I tried deleting the old connection and recreated a new one in the nm. But still does not work.
[Code]...
View 7 Replies
View Related
May 18, 2010
i'm trying to get my WLan working, i do have a Broadcom BCM4312 lpphy WLan-Adapter (pci-id according to lspci -vnn is 14e4:4315) in my Lenove ideapad S12. My System is Debian Lenny, but in order for the WLan-Adapter to work I installed the 2.6.32-3-686 Kernel from debian squeeze (using apt-pinning). I than installed the b43-firmware as described in the debian wiki [URL]. I updated the init-ramfs, everything is working as expected, except for WLan.
It shows up using iwconfig, i can get it up and down using ifconfig (or ifup, ifdown). I can't do a scan using iwlist - it says: % iwlist wlan0 scan > Failed to read scan data : Resource temporarily unavailable
It always fails, but not with the same error message. Sometimes it also comes up with > device or resource busy
Using dmesg I see reports about a fatal DMA error, resulting in a controller RESET. It says it's loading firmware 478.104 .
View 4 Replies
View Related
Jun 23, 2011
i have debian squeeze installed on my lenovo t61 notebook with intel wireless 3945 firmware.
i've installed the firmware-iwlwifi package but cannot get any wireless connection.
i'm using the fluxbox dekstop with wicd network manager.
i've searched around on the debian user forum archives and the internet but have yet to find a solution for this. it seems most people have just installed the firmware-iwlwifi package and then wlan was working.
i had ubuntu installed on this machine before with wlan running, so i know that there is nothing wrong with my hardware.
View 14 Replies
View Related
Sep 6, 2015
Debian encrypted LVM disappears every time on sda when I install any other also encrypted Linux distro on sdb.
How can I set up Debian that way that it wouldn't disappear or how can I recover it form UEFI?
View 1 Replies
View Related
Apr 11, 2011
I have a fresh install of squeeze without a desktop environment. I then installed a basic gnome environment so I can choose my own apps ('apt-get install gdm3' pulls in enough for that). I then had to install some packages to get mobile broadband working:It all works fine until I disconnect it via Gnome network manager. I cannot reconnect using Gnome network manager because it doesn't show in the menu, but it does show while I'm connected. If I pull the dongle out and plug it in again, it reconnects without issue.I think I may be missing some packages, but I don't know what. I tried usb-modeswitch, but no change
View 10 Replies
View Related
Jan 10, 2010
i use a telekom s100 set-top-box, which originally had a prism54 wlan-card. but wlan was very slow. but the driver was working well and it did not seem to be a configuration issue, so i assumed that its that card which is so slow. following i purchased a atheros based wlan-card which is working perfectly well with the ath5k driver of my linux kernel (2.6.26-1-686). but the connection is pretty bad anyway. i get max 300kb/s from pc to pc. as its the same with 3 different cards i tested in the s100 i assume it is a configuration issue? or might there be chipset or mini-pci-slot limitation?
when i check the connection with iwconfig the bitrate is somewhere between 1-54mb/s, rising to 54mb/s and then falls back to 1mb/s, rising to 54mb/s again, falling down, its an infinite loop. im using wpa_supplicant for the connection, but i don't think thats the malefactor. well, you never know .. i tried to set the bitrate with iwconfig wlan0 rate 54M but that ended in a disconnection ...
[Code].....
View 3 Replies
View Related
Jul 18, 2011
I´ve set up a Squeeze System on an old Ibook G4 and, besides wlan, everything works fine.i guess i need some firmware, i have tried several things and couldnt resolve the problem. I am unsure which firmware i actually need, or of something else has to be done.i´ll post the outputs of ifconfig, iwconfig and lspci and hope someone who could guess the problem or find the solution with it.
root@debian:/home/robert# ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:11:24:32:20:54
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[code]....
View 1 Replies
View Related
Jul 23, 2015
Since a recent update on Stretch, I have been unable to use the network-manager to connect to my home wireless network on my laptop. It was working fine before. I did not change any settings on the WLAN router. I can still connect to other wireless networks at work and university, just not this particular one at home. All other non-Debian devices in my household are still able to connect just fine.While figuring this out, I have tried connecting manualy with ifup but I don't really know how that works. Right now there is only the loopback entry in /etc/network/interfaces.
Below is the output of syslog, when gnomes network-manager is trying to connect, but fails.
Code: Select allJul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: starting connection 'Affenbande'
Jul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: Stage 1 of 5 (Device Prepare) scheduled...
Jul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: Stage 1 of 5 (Device Prepare) started...
[code]...
View 14 Replies
View Related
Jul 6, 2010
I have a set of vm's with stable, testing, and sid to keep track of how things are going. When I did an apt-get dist-upgrade with squeeze last week, things seemed to OK (350 package updates) until the end. It didn't seem to like and / or was confused by a kernel dependency.
I am not too concerned yet. Because these are in vm's, I do a snapshot before any significant change. I can futz around with impunity because I have that backup.
I re-booted, and tried the apt-get dist-upgrade again with same results. I think I also tried apt-get -f install.
So I reverted to the snapshot, and will simply try again in the future. I recall that with lenny as testing, the font-desktop was really screwed up for about a period of 6 weeks.
However, just in case someone else runs into this:
1) a re-boot worked, but the failure of apt-get made me nervous enough to revert.
2) waiting for corrections has seemed to work in the past (with a single exception with a 4-disk SCSI software RAID10 update that failed to re-boot lenny successfully after what seemed to be a minor update -- that was on a real system, not a vm. I haven't gotten back to look at that.)
View 14 Replies
View Related
Feb 8, 2011
I recently just installed Squeeze on an ia64 system and was having some troubles with running VNC.I get the following error, more specifically for some reason I get a malloc - memory corruption error:
Xtightvnc(9165): unaligned access to 0x60000000001ea06c, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea074, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea07c, ip=0x4000000000268280
Xtightvnc(9165): unaligned access to 0x60000000001ea084, ip=0x4000000000268280
[code]...
After display all the code above, it just stops. The port 5901 is still closed - if it runs properly, would it open automatically?Is there something that is incompatible? Or am I missing some system configuration component?
View 1 Replies
View Related
Feb 19, 2011
how to install Dropbox for Debian Squeeze from source.Please read everything before you begin. I prepared it as I installed Dropbox for my own system. Please Note: I use sudo, you may have to use root or 'su' from the command line. If you don't know the difference between sudo and su, then you shouldn't try this until you know. At the time I did this, the lastest dropbox version was 0.6.7.
View 7 Replies
View Related
Apr 5, 2011
I installed Firestarter firewall on debian Squeeze.Now i note there is a gui available in System->Administration which apparently does not need to be running all the time - its not set up to start on boot.When I boot I notice the boot message has a line saying "Starting Firestarter firewall .... failed"When I am logged in and type "/etc/init.d/firestarter status" as the Firestarter FAQs say, I get"Firestarter is running... ... (warning)"I can run the gui manually and still same message.
View 2 Replies
View Related
Aug 28, 2011
When I activate Tor in Iceweasel, it forbids me access to the internet completely. Even attempting Google results in "Iceweasel is configured to use proxy server that is refusing connection".
I have seen this in Lenny, too - it was caused by activating Tor without having installed privoxy. I installed privoxy and everything was okay. In Squeeze, Tor is using polipo. Polipo is installed and running. I have not played with settings of polipo or Tor, the configuration is the same as it was after installation.
What can be wrong? I am a rather an user than a networking guru. I am connected to internet by means of DHCP, no local lans, no special routings, no additional proxies. I have already tired to reinstall polipo.
View 2 Replies
View Related
Feb 15, 2010
Just installed squeeze on a new laptop(had been runny Lenny on my older one with no issues, but no sound or wireless on the new one).I decided to install the ATI drive for my Radeon Mobility 4500(or some close revision) because the fan is constantly running and based on some other postings, it seems that it could be the graphics card causing it.Downloaded the driver from ATI's site and it seemed to install fine but when starting X.
View 11 Replies
View Related
Jun 20, 2010
When I try to downgrade from sid squeeze I don't get GDM running just a login promt after a reboot.Have also reinstalled nvidia driver but still only login promt.I did aptitude update and aptitude full-upgrade after changing sources.list from sid to squeeze.
View 2 Replies
View Related
Oct 19, 2010
Got a problem mounting my Windows partition in Squeeze. It keeps refusing to mount it for me in Dolphin. I am a member of the disk and fuse groups, /dev/fuse is owned by root:fuse, and /sbin/mount.ntfs points to /sbin/mount.ntfs-3g, which in turn points to the ntfs-3g executable. I kind of need this ASAP. I am supposed to be finishing with this machine in 35min, and I am dead in the water without the ability to copy some files from the Squeeze ext4 partition over.
View 14 Replies
View Related
Oct 21, 2010
I installed Debian Squeeze from a net install to a raid 1 array. I have been having a lot of troubles related to being able to write to one or more of the mounted drives - even touch gives me errors.
The most interesting line from dmesg is:
Here is the full output from dmesg:
I found a thread that indicated that this bug was fixed in the next kernel version: 2.6.32-6. I am willing to upgrade the kernel to get rid of my problems. Is a squeeze kernel at 2.6.32-6 or higher available? If so, where? I have not compiled my own kernel, and am not very interested in getting into that.
View 8 Replies
View Related
Dec 20, 2010
I use my laptop at the college, and I've to suspend him frequently. So, I've decided to install the package pm-utils, to hibernate my PC, instead of power off it. When I try to do "# pm-hibernate", a tty appear, and this error is displayed :
[3506.405310] pm_op(): usb_dev_suspend+0x0/0xa [usbcore] returns -2
[3506.405310] PM: Device usb1 failed to freeze: error -2
This is the result in pm-suspend.log :
Initial commandline parameters:
[Code]....
View 14 Replies
View Related
Feb 6, 2011
I have upgraded my server to Debian 6.0 Squeeze but it looks like some of my sites are not compatible with PHP 5.3.x so I would like to revert to previous 5.2.6 version.So my question is what to do?a) Remove PHP 5.3.x from system via apt-get and install my old 5.2.6 from old archives at /var/cache/apt/archivesorb) just try to update from archives PHP to 5.2.6?
-rw-r--r--. 1 root root 2413316 May 11 2008 libapache2-mod-php5_5.2.0-8+etch11_i386.deb
-rw-r--r--. 1 root root 2413290 Oct 6 2008 libapache2-
[code]...
View 10 Replies
View Related
Feb 6, 2011
As a long time user of some other distributions I decided to switch to Debian and installed 6.0 from amd64 kde cd image.Upon logging to KDE I discovered thatant locate knetworkmanager anywhere,it doesnt autostart and I could not find it anywhere else.I am connecting through a wireless network to the Internet so I cant connect through the Ethernet to download it through apt-get for example,if it is not installed by default.lly confused,knetworkmanager is standard tool in KDE but I cant find it in Debian 6.0
View 9 Replies
View Related
Dec 14, 2010
A couple days ago I installed Debian Lenny (netinst) to my friend's laptop, a IBM Thinkpad T23. Got a black screen after gdm loaded and the laptop seemed frozen. Decided to upgrade to squeeze. I edited the apt sources file and changed all the instances of lenny to squeeze, and then upgraded.Had the same display problem, but found a web site that suggested disabling acpi. So I did that, got the sound working, (needed cs46xx firmware), and all seems to be running fine.I get some weird udev messages at boot time, but I have a feeling that's due to how I upgraded. I can't copy and paste since the messages aren't in my system log. If anybody wants more information about it, I can supply it. pgrep shows two instances of udev running so it appears the messages are only warnings.When upgrading to squeeze, I used tds.net debian mirror links. Earlier today I switched to Debian's official US repo URLs and had to upgrade about 250 packages after reloading package data.
Now, when I click on System -> Administration -> Time and Date.After a couple seconds I get a dialog box that says "The configuration data could not be loaded" in bold black letters. Underneath that in smaller letters, "You are not allowed to access the system configuration" I receive that same error when accessing "services" and "users and groups."But I can access the synaptic package manager and update manager from the administration submenu.
View 4 Replies
View Related
May 26, 2010
I've just install debian squeeze version, or the testing one, but I am not really happy with it. Is not listening me all the time. If I install the debian stable I don't have internet connection. Is it possible to update the kernel somehow using the testing version?
View 12 Replies
View Related
Apr 3, 2010
I've been testing Squeeze to determine whether KDE4 is finally suitable for my primary machine. Everything seems to be working fine except for detection of IDE devices. My CD/DVD drive no longer automounts and the reason seems to be that no device is being created. My Lenny system detects the drive as /dev/hda, but no such device exists in Squeeze. During boot, Squeeze appears to detect the drive as /dev/sr0 (according to dmesg), but in fact that device does not exist either.I'm actually running the Lenny kernel, as I am unable to compile my Ralink wireless driver (rt2860sta) using the Squeeze kernel. Also, for inquiring minds, I use removable HDD drive bays on my systems to simplify testing.
View 9 Replies
View Related
Apr 13, 2010
I have been trying to build a Debian-live-version for some time using live-helper. It works fine if I choose lenny as distribution. With sid I always get into trouble.Sometimes live-helper does't find any aufs-modules but it stops looking for them if I keep the options as simple as above.What is the problem of live-helper's to build on sid or squeeze (which I have met similar troubles with)?
View 10 Replies
View Related
