Fedora Installation :: Upgrading From Core 4 To Core 10?

May 20, 2009

I have created a virtual machine of a system running Fedora Core 4 and I need to upgrade it to Fedora Core 10. Based on what I have read, it iis possible so I started theupgrade process. I get an error message saying that /dev/hda6 (my root paritition does not exist) even though it does.

Does the installer need to read a label from /etc/fstab? I executed tune2fs -L / /dev/hda6 amd ,and added LABEL=/ for the corresponding entry for fstab. but the FEDORA CORE 10 is still giving the same problems for the installation process. Should I upgrade to an intermediate verson like Fedora Core 7 first?

View 14 Replies


ADVERTISEMENT

Fedora Installation :: Dual Core Only Showing Single Core On F14?

Nov 3, 2010

I just loaded F14 on an old Dell Dimension 3000 with a dual core processor but only one is showing. Here's the output from top:

processor: 0
vendor_id: GenuineIntel
cpu family: 15
model: 4

[Code]....

View 2 Replies View Related

Ubuntu Installation :: Dual Core Support Core 2 E8500 Out Of Box?

Feb 14, 2010

Just a quick question. Does Kubuntu Karmic support core 2 E8500 out of the box or do you need the SMP kernel?

View 3 Replies View Related

General :: Upgrading From Fedora Core 7 To CentOS 5.4

Jan 19, 2010

I need to upgrade one of our systems from its current distribution, Fedora Core 7, to the most recent version distribution, release 5.4, of the CentOS operating system. Can I do an in-place upgrade of the operating system without any adverse side-effects? Are there any issues that I should be concerned with before proceeding?

View 10 Replies View Related

Software :: Install Older Version Of Gcc 2.95.3 In Fedora Core 8 Or Fedora Core 12?

Mar 14, 2010

i download the rpm package of gcc .

View 10 Replies View Related

Ubuntu :: Run Dual Core - Crash - Single Core Runs Perfect

Apr 1, 2011

i am running gigabyte GA-M68M-S2P and AMD sempron 2.7. the problem is when i try to run dual core. it will boot and run for 2mins then it crashes. single core runs perfect.

View 6 Replies View Related

OpenSUSE :: Get Application To Utilize More Than One Core In Multi-core Setup?

Mar 27, 2011

I have a command line OCR program called OCR Shop XTR (Vividata corp) that I am using on a system with a 6-core AMD chip. I changed the bios so that the 6-cores were activated, but htop shows me that while the program is running, I am only getting activity on one core (the program maxes out the one core with consistent usage between 97% and 100%).

I have read that many programs are not written to take advantage of multiple core cpu's. However, I am just hoping that there is some way to get this program to take advantage of the extra cores. Does anyone know of a way to invoke programs from the command line which would spread the workload out among additional cores?

Here is the output of uname -a:Linux linux 2.6.37.1-1.2-desktop #1 SMP PREEMPT 2011-02-21 10:34:10 +0100 i686 athlon i386 GNU/LinuxAnd here is the output for one of the cores from cat /proc/cpuinfo:processor : 5

vendor_id : AuthenticAMD
cpu family : 16
model : 10
model name : AMD Phenom(tm) II X6 1100T Processor
stepping : 0

[Code].....

View 5 Replies View Related

Programming :: Multi-core Support - Control On What Core Will A Thread Run

Oct 31, 2010

Is there any Linux API that will let me control on what core will a thread run? If not, do I have to use assembly language?

View 2 Replies View Related

Debian :: Wheezy Only Recognizes 1 Core Or Dual Core CPU?

Sep 7, 2011

I have now installed Wheezy on two different hard drives and in each case it seems only one CPU of my dual core CPU computer is recognized. System Monitor, Gkrellm and lscpu show just one when prior to the new install the old Wheezy showed both CPU's. I have put the hard drive into two other computers with dual core CPU's and all show just one CPU.

Interestingly System Profiler and Benchmark (hardinfo?) > Devices > Processors now show a large amount of processor infomation when with the old Wheezy I would only see both CPU's listed and nothing else.

View 14 Replies View Related

Ubuntu :: Lucid Lynx - Dual Core - One Core Always At 100%

May 15, 2010

I've a Compaq CQ61 laptop, and i noticed that one of the cores is always at 100%.

I didn't check the duration of the battery but surely it will "eat" my battery in a hurry

View 1 Replies View Related

General :: Only One Core Of Dual Core Processor Are Working

Mar 14, 2011

I recently read in a forum that by default the Linux kernel only activates one of two cores in a dual core processor. Searching online gave one option to find out and that was the mpstat command. I therefore ran the command and got the following output.As the result says, it shows only 1 cpu. I was wondering what I could do to activate both cores in my machine, and whether doing so was going to cause me any problems.

View 14 Replies View Related

Programming :: Get Process Running CPU Core And The Utilization On That Core?

Apr 27, 2010

Assume someone bind a particular process to a particular CPU core(In multi core machine) by using sched_setaffinity() like functions. Then how we can get that process running core id and CPU core utilisation of that process on that running CPU core(Pragmatically or by a Linux command)?.

View 5 Replies View Related

General :: Difference Between Fedora Core 4 And Fedora Core 14?

Jan 12, 2011

I am in school for my CIS degree and the book I am using this session covers Windows XP and Fedora Core 4. I am having trouble finding & downloading Fedora Core 4. My question is: Is there a big enough difference between Fedora Core 4 and Fedora Core 14 that I would not be able to use 14 instead of 4?

View 14 Replies View Related

General :: Processes And CPU 4-core - Which Core The Program Used?

Mar 26, 2011

I've a program that launches new processes, and wait for them to die before it exits. So, for example, my program is a process, and it launches 3 more processes, and when the 3 child processes end, it will exit.

As you see, at end of the example, the program used a total number of 4 processes.

1 - Now, I'm running this program in a CPU with 4 cores. This means that the program used each core for each process?

2 - How can I know which core the program used?

View 1 Replies View Related

Programming :: Core Dump Issues. Program Crashes But Does Not Generate Core Dump File?

Oct 7, 2009

I want to generate core dump files from my program when it crashes. Its a pretty big process and has about 10-11 threads in it.I have followed the documentation to enable core dump by setting ulimit to unlimited etc. I quickly tried "A demo program creating a core dump" from the following webpage, which succeeds in Segfault and dumping a core file in the directory that I configured.However, I tried running my original program and caused it to crash. I did this by making calls to kill(), raise() or the same null pointer access as shown in the webpage above. In each case, my program crashed but did not generate a core dump file. Am I missing something?My program is in C++ and my environment is Redhat 9.0 (kernel 2.4.20)

Going through the "Why do I NOT get a core dump?" section on the same webpage as above, I can see two potential problems. One - there are issues with the suid/sgid (bullet # 6). I am not able to change any settings with suid because my system does not contain either /proc/sys/fs/suid_dumpable or /proc/sys/kernel/suid_dumpableTwo, my program has threads in it and the bullet # 8 is the problem.

View 1 Replies View Related

CentOS 5 Hardware :: Infiniband (mlx4) Works On 16-core System But (now) Fails On 32-core System

Jan 27, 2010

We have a small cluster of 20 HP systems, all running CentOS 5.3 in an NFS-root environment. Half are quad-socket, quad-core Xeon E7340 @ 2.40GHz (total 16 cores), the other half are 8-socket, quad-core Opteron 8354 (total 32 cores). All systems have a Mellanox Infiniband adapter ("Mellanox Technologies MT25418 [ConnectX VPI PCIe 2.0 2.5GT/s - IB DDR / 10GigE] (rev a0)")

With kernel 2.6.18-128.1.6.el5, infiniband works fine on all systems.

With the update to kernel 2.6.18-164.11.1.el5 (and both types of node running the same NFS-root image), the 16-core Xeons still work fine. Infiniband no longer works on the 32-core Opterons. Specifically, either the ib0 interface fails to appear, or it does appear but when configured with an IP address, doesn't actually work. In either case, loading the IB kernel modules takes a long time, but I haven't instrumented the load script yet to see which module, if any, is at fault. More errors listed below.

However, if I tweak the BIOS of the 32-core systems to reduce the per-socket core count to 2 (so effectively 8-socket, dual-core, down to a total of 16 available cores), Infiniband starts working again. Putting it back to 32-cores makes it fail. Booting the older kernel makes it work again. In summary: old kernel, IB works on all systems. Newer kernel, IB only works on 16-core systems.

Updating the IB firmware from 2.5.0 to 2.7.0 (latest available) doesn't help. I also did a full 'yum update' to make sure that libmlx4, openibd all other associated packages were up-to-date. Doesn't help either.

Some errors that appear on 32-core nodes:

ib_query_port failed (-16) for mlx4_0
ib_query_port failed (-16) for mlx4_0
mlx4_core 0000:04:00.0: SW2HW_MPT failed (-16)
mlx4_core 0000:04:00.0: SW2HW_MPT failed (-16)

[Code]....

View 5 Replies View Related

Ubuntu :: Only Single Core Active On Quad Core AMD When Acpi Is Active?

Jun 8, 2011

Only Single core active on quad core AMD when acpi is active.with acpi=offuname -aLinux dvip4 2.6.32-30-server #59-Ubuntu SMP Tue Mar 1 22:46:09 UTC 2011 x86_64 GNU/Linux

Code:
cat /proc/cpuinfo
processor : 0

[code]...

View 1 Replies View Related

Fedora Installation :: How To Updated To 13 From Core 4

Sep 27, 2010

I set up my home server like 3 year ago on a Fedora core 4, I am running a NAT, firewall and FTP very smoothly on it. In the past 3 years, it has been doing perfectly without any modification/ upgrade. But recently, I just realized I might need a VPN server on it, but the recent release of OpenVPN doesn't support Fedora core 4 anymore, therefore I suddenly want to make an upgrade. I've read the articles/ manual for Fedora 13, yet I do not find any suggestion on how to upgrade to 13 from core 4.

how can I do an upgrade in the easiest manner as I don't want the server cease working too long (I need its NAT for my network).

View 11 Replies View Related

Installation :: Get Wireless Driver For Fedora Core 10?

Jan 20, 2009

Where can I get the wireless driver for Fedora core 10. I am using a 64 bit system with a hp pavilion notebook.

View 7 Replies View Related

Fedora Installation :: Can't Install Core 10 Into XEN VM / Get It To Work?

Feb 8, 2009

When I am trying to install Fedora Core 10 into a XEN VM i get an error stating that images/xen directory does not exist on the DVD image.

View 2 Replies View Related

Fedora Installation :: Cannot Install Core 10 Monitor Out Of Range?

Jan 15, 2009

I cannot install Fedora core 10. It boots up and it gets to the Fedora 10 loading screen. After that it complains my monitor is out of Range and that's as far as I can go. I had originally thought I could get to some text install mode, but I don't make it far enough to do that.

View 1 Replies View Related

Fedora Installation :: Mkisofs Rpm Package For Core 6 On 32 Bit Machine?

Apr 12, 2009

Since the yum repository for FC 6 is no longer available, I'm looking for a place to find the latest package of mkisofs that can be used on FC6. I could not find a decent place to download it from.

View 2 Replies View Related

Fedora Installation :: Got An Update That Installed, And After A Reboot One Core At 100%

Aug 12, 2009

I just got an update that installed, and after a reboot I've got one core at 100%. The "you need to restart" icon in the notification tray said "glibc glibc glibc glibc nscd". Now that I look at it, It's switching between both cored. This behavior is consistent over multiple full reboots as well as kexec reboots.

Edit: Strange, just when I finished, the CPU load settled out and now everything is fine. I wonder what was going on. I'm rebooting right now to double check. Edit2: Yep, same issue 100% usage on one core. And it probably will level out soon. I'm not sure what could be causing this. I assume that glibc could be the issue.

View 3 Replies View Related

Fedora Installation :: Core 11 And Windows 7 Dual Boot?

Nov 3, 2009

I just installed Windows 7 Ultimate on my computer and I want to install Fedora Core 11 and dual boot my system. I have been on the net looking around, but I can't seem to find any suggestions on how I would do this. Can someone help me or give me a URL(s) that will give me a step-by-step guide on how to install Fedora Core 11 on a Windows 7 computer?

View 4 Replies View Related

Fedora Installation :: 12 Live/KDE: Only One Processor Core Works?

Mar 6, 2010

I wanted to try Fedora 12 Live/KDE on a newly-bought Fujitsu Esprimo P1500. Booting with no kernel options would just freeze the machine. After some random experimentation, I added the option "nolapic" and got a seemingly working machine. However, only seemingly, as it turned out that only one of the processor cores was working (the processor is a "Pentium(R) Dual-Core CPU E5300").

View 4 Replies View Related

General :: SATA HDD Not Detected During Fedora Core 4 Installation?

Jan 24, 2010

I am trying to install FC4 in my pc having WDC WD800JD SATA HDD. During the installation it shows that no HDD found. I have searched a lot but no driver are found for fedora core 4.

View 10 Replies View Related

Fedora Installation :: Upgrade From 9 To Core 10 - Couldn't Load Xpcom

Jan 29, 2009

I upgraded from 9 to 10 and now i can't use firefox it says "couldn't load xpcom" anybody know what i could do..

View 3 Replies View Related

Fedora Installation :: CD/DVD Boot On Intel Core 2 Duo VPro Stalls?

Jun 13, 2009

I've been using Linux (Fedora) since 2005 (when I happily abandoned Windows) and loved every minute of it. No installation or other unresolvable problems. But now, I am totally stuck. A month ago, they just gave me a new desktop in the office: Dell Optiplex 960 with the Intel Core 2 Duo vPro chip. So I waited for Fedora 11 to come out, burned the x86-64 Install Media on a DVD, repartitioned the hard drive like I always do on new Windoze machines, and began installing. The install process gets to this announcement and stops:

mounting /tmp as tmpfs... done Then, after a 5-minute wait, if I push the power button on the computer for a hard reboot, then it says:

running install running /sbin/loader and then stalls for good. Then all I can do is hard-reboot again.

So, out of curiosity (and for other reasons), I tried booting the machine from other linux disks: Knoppix, and SystemRescue (www.sysresccd.org). They all stall at different points. The funny thing is that both Fedora 11 x86-64 and SystemRescue happily boot on my personal one-year-old Lenovo T61 Intel Centrino Duo VPro laptop.

I get a feeling that somehow the Intel Core 2 Duo vPro is causing the problem. I also think that there is got to be someone else out there who either had this problem, or was able to install F11 on similar Dell box. Google search did not produce actionalbe answers for me.

View 3 Replies View Related

Fedora Installation :: F14: Select Just The Core Gnome Packages When Installing?

Nov 5, 2010

I'm trying out Fedora 14 on an Asus EeePC 1000 netbook.I'd like to install just the basic Gnome interface, its helper applications and Gedit &cI don't want openoffice or evolution &c on this small net book.How would I go about choosing the appropriate packages at install time?If this is documented anywhere, just point me at the page!

View 2 Replies View Related

Fedora Servers :: Configure Openssh, /etc/sshd_config On A New Installation Of Core 14?

Nov 11, 2010

How to configure openssh, /etc/sshd_config on a new installation of Fedora Core 14? [since tt does not work right out of the box, I cannot ssh into it]

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved