Is there a way to configure DHCP IP Reservation thru MAC ? eg. {MAC ADDRESS} 192.168.1.23 So, when somebody owns this MAC address leases IP, it will give the one in reservation. Also, for security in mind, DHCP will ONLY lease IP if its MAC address is listed, otherwise, DHCP will NOT give IP.
View 1 RepliesI am puzzled with trying to configure a linux (openSUSE) client to dhcp to eBox DHCP server. I am using dhclient to lease an IP address with dhclient eth0 -s 10.45.48.108 and get a response
openSUSE11232CL1 dhclient: DHCPDISCOVER on eth0 to 10.45.48.108 port 67 interval 4
openSUSE11232CL1 dhclient: DHCPOFFER from 10.45.48.108
openSUSE11232CL1 dhclient: DHCPREQUEST on eth0 to 10.45.48.108 port 67
openSUSE11232CL1 dhclient: send_packet: Network is unreachable
openSUSE11232CL1 dhclient: send_packet: please consult README file regarding broadcast address.
The server reports eBox141 dhcpd: DHCPDISCOVER from 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
eBox141 dhcpd: DHCPOFFER on 10.45.200.2 to 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
I interpret this as the server receives the request and the client accepting it but the lease does not last long and the connection breaks. what this could be and why the connection breaks? Or my undestanding is totally wrong on how it works and should work? And BTW, where is that README file that's referenced in the message I receive on the client?
Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
I'm running Ubuntu 10.10 and I'm having problems trying to assign it a static IP address. No matter what I put in the Preferences->Networking area (identifying the interface as Manual)... it still will query DHCP for an address if I run the dhclient command. I'm using to using ubuntu server where I just set the IP in the interfaces config file.
View 1 Replies View RelatedCan't change from dhcp to static ip address.I've installed Oracle's version of Linux Redhat 5, but I'm having no success changing from dhcp to a static IP address. My machine is plugged directly into a Belkin router which has the IP address: 192.168.2.1.If I use the gui: /usr/bin/system-config-network and set the network device to dhcp,it works fine. But if I set the IP address manually, I get no internet traffic, and if I ping an internet website, "network unreachable".The installation instructions for Oracle say that they want a full domainname. I've tried gateway.2wire.net. This worked in the last place I did a successful installation.It was the address of my ATT router. If I plunked that into a browser, I got the router configuration.
View 7 Replies View RelatedI would like to define a IPv4LL address (169.254.0.0/16) in parallel with the DHCP address received from the server on the same network card. I tried to modify /etc/network/interfaces to that effect (see below), but either I only manage to get one of the two at any time.
auto lo
iface lo inet loopback
auto eth0 eth0:1
iface eth0 inet dhcp
iface eth0:1 inet ipv4ll
I noticed that my internet connection wasn't automatically brought up each time I logged into Fedora so I opened the system-config-network tool and edited my network adapter by checking the box marked "automatically start at boot/login." To my surprise, the connection went down and upon trying to click on the device to let the manager bring up the connection the greyed-out phrase "device not managed" appeared underneath the device name and wouldn't allow me to connect.
Even when I used ifconfig/dhclient to get the connection up nothing happened. I could get the router to assign an IP address through DHCP, pinged a few sites to make sure it was legit, but still couldn't use firefox to browse anything. Seems as if network manager GUI is conflicting with command line attempts to bring the network up. I'd like to permanently disable system-config-network if possible because it's acting screwy!
I'm using Ubuntu 9.10, and I want DHCP to assign an IP address automatically. I can ping my router, and get a reply. I just have no idea how to do this.I'm trying to get my Ubuntu machine onto my Windows network.
View 9 Replies View RelatedDoes anyone know an easy way to do this? I can't seem to figure it out.
View 6 Replies View RelatedI don't really have a reason for this currently. I recognize all the MAC address on my DHCP client list and keep it rather well locked down. I was just wondering if there was something I could run on the terminal to get more information on a given MAC address on my network. Something kind of like whois for websites.
View 1 Replies View RelatedI have an Ubuntu 10.04 server. It gets its IP address by DHCP (the router has a fixed reservation so it always gets the same one). However, it needs its nameserver to be itself, and not the DNS servers given out by the router. How can I make dhcp not overwrite resolve.conf?
(Yes I know I could just set a static IP. But I'm testing stuff out here, and want to know if it can be done without doing that.)
We have a large number of devices on our LAN with the mac prefix of 00:60:60. We want to assign these addresses from a separate address pool. I've created two classes, one to match 00:60:60 and another that I want to contain any other device. When i try to start the server I get:
/etc/dhcp3/dhcpd.conf line 33: boolean expression expected
match if not binary-to-ascii(16,8,":",substring(hardware, 1, 3))
^#this carrot should be under the last parenthesis#
Configuration file errors encountered -- exiting
Here is the relevant section of /etc/dhcp3/dhcpd.conf
class "006060" {
match if binary-to-ascii(16,8,":",substring(hardware, 1, 3)) = "00:60:60";
}
[Code].....
I've tried a few variations on that line. I've spent days trying to find any examples of "match if not" and haven't found anything. I assume it's going to be something to do with parenthesis/quote placement. Oh and this is ISC DHCP Server V3.0.4.
I have an Ubuntu Server 10.04.1 that I have given a static IP address. Every six hours or so I will lose connectivity to it and when I type ifconfig to look at the network information, it has been given an address via dhcp. If I run the /etc/init.d/networking restart command the IP address goes back to my static address and things are fine for another 6 hours or so. Here is what is in my interfaces file:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 10.60.82.15
netmask 255.255.0.0
broadcast 10.60.255.255
gateway 10.60.254.254
This machine is also a DHCP server and I checked to make sure there are no other DHCP servers on my network. Right now my fix is to have a Cron job running that runs the reset command every 5 hours, but I would like to find a more permanent solution.
I want to setup 1Gbps our lab network and we purchased 'Buffulo Giga layer switch ' with 24ports. Is there a way to tell DHCP to assign specific IP to a particular MAC address of a machine ? We want to use DHCP and whatever the port we use ,it should have same IP ..
View 1 Replies View RelatedI am attempting to get this network card running under CentOS 5.2 but have had no luck. Some sites say to use the sk98lin driver, others the skge, which I can't find at all. I have tried multiple versions of the driver in rpm but none seem to work. The card shows under the network manager but will not get an IP address from the DHCP server.
Here are the outputs for this card.
uname -rmi
2.6.18-92.1.10.el5 x86_64 x86_64
lspci -m
04:01.0 "Ethernet controller" "D-Link System Inc" "DGE-530T Gigabit Ethernet Adapter (rev 11)" -r11 "D-Link System Inc" "DGE-530T Gigabit Ethernet Adapter (rev 11)"
lspci -n | grep "$(/sbin/lspci | awk '/net/ { print $1 }')"
04:01.0 0200: 1186:4b01 (rev 11)
lspci -vv
04:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11)
Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 121
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at e800 [size=256]
Expansion ROM at e0000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
How to get this working as we have 3 of these cards for computers without a Gb NIC and I don't want to fight with it 3 separate times.
I have installed Fedora 10 on my A860 Dell Vostrol Laptop with AR242X Atheros Wireless card. Wireless card worked out of the box and i could detect wireless network and connect to it. But i have a problem that, my wireless connection is not able to get IP address from the DHCP server. Please help me out what can i do to get this working. I am using WEP security and authentication is open system.
I have windows 7 beta installed on the same machine and on that wireless network works fine so i am sure that there is no problem with the wirless network. I am using DIR-300 router from D-LINK. I tried to see packet log on wireshark and there i see that there is no reply to the DHCP discover message. Actually i don't see any RX packets at all. Which is not normal as there is traffic on the network.
When I install Fedora 10 on a new system, I let it default to DHCP. Later, I change the system to a fixed IP address by running system-config-network, selecting eth0, clicking on "Edit", clicking on "Statically set IP addresses:" and filling in the blanks. Is it possible to accomplish the same thing using commands that could be entered in a script? I assume one of them would be
Code:
ifconfig eth0 address XXX.XXX.XXX.XXX netmask 255.255.255.0
The cable internet I'm using runs on Dynamic DHCP IP addresses. I changed it to a static IP address in my router settings, but it keeps changing. This means that I can't connect to my home server from a remote location.
Is there anyway to run my ubuntu server on a DHCP IP address without connecting through my router 192.168.1.xxx?
For changing the the mac address of my lan card( eth0) in linux fedora 9(solphur) i used this command
And i could change my mac address successfully but now i couldn't connect to my network via a dhcp server ( in configuration section of my router im going to check my new mac address (because i want to spoof) ,how i can do that?
This one has been bugging me for some time now. The network interface (as defined in Debian's /etc/network/interfaces file) fails to obtain an IP address from myuter. However dhclient br0 does.I'm using br0 since I run a XP virtual machine.network/interface changes are from a Debian howto on setting up the tap interface.As near as I can tell, the /etc/init.d/networking script basically calls /sbin/ifup -a. ifup is a binary.My /etc/network/interfaces file is:
auto lo
iface lo inet loopback
address 127.0.0.1
[code]...
My DHCP setting is disabled in fedora 12 . Previously i was using static IP address. I Want DHCP setting enable, any idea.
View 1 Replies View RelatedI've only been using linux for a few days so I don't know all the tricks. I'm pretty savy configuring windows networks however.My adapter is (according to windows) a: CNet PRO200WL PCI fast ethernet adapterLinux says it is a: 21x4x DEC-tulip compatible 10/100 EthernetI do seem to be getting an ip address from the DHCP router, but I cannout ping any other ips or connect to the internet.I've tried a bunch of different options, switching things back and forth, but it still doesn't work, and honestly i don't even know what some of the options mean.
ALSO, if this helps:
paladin:~ # ifconfig eth0
Eth0 Link encap:Ethernet HWaddr 00:08:A1:03:3C:99
[code]....
I'm having an issue configuring eth0. I'm using ubuntu 8.10 in a virtual machine (VirtualBox). The correct adapter is being used and it has worked in the past. I've tried placing eth0 in dhcp through the GUI and bash, but always get a 169 address or 127.
When I run the following command:
Code:
The output is:
Code:
I setup the dnsmasq in debian squeeze as dhcp and dns server, for the debian host i assigned the static ip addresses, and configured the xp for dhcp. Windows XP network can't acquire DHCP address from debian squeeze with this error:
Quote:
error unable to contact your dhcp server Request has timed out.
this is the tcpdump output in debian for the xp network:
Quote:
15:12:10.631635 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:07:e9:a8:ea:93 (oui Unknown), length 300
15:13:16.611793 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:07:e9:a8:ea:93 (oui Unknown), length 300
15:13:16.611793 IP 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request from 00:07:e9:a8:ea:93 (oui Unknown), length 300
15:12:42.631730 ARP, Request who-has 169.254.202.161 tell 169.254.202.161, length 4615:12:44.613568 ARP, Request who-has
[code]....
I'm using a D-Link Xtreme N PCI express wireless adapter (DWA-556). It shows up in the network manager.
However it does not get an ip address from the DHCP server. Below is what I get in the messages log:
I've set up a permanent DHCP lease for my MAC address. I did this hoping to resolve the fact that I share my Internet ADSL connection with my wife and my daughter (the latter a great bandwidth hog)!
View 5 Replies View RelatedI am having a problem getting a wireless network connection on my DELL laptop running CentOS 5. I have no problem getting a wireless connection when the laptop is booted in Windows XP. I also don't have a problem when booted under CentOS 5 and there is no authentication setup on the wireless router. I only have a problem when I setup authentication. The router wireless log shows the PC connectinng, authenticating, and succeeding authentication.I am using the Broadcom Hybrid-wl wireless driver.
View 19 Replies View RelatedI have a network with one of the server machine being under Fedora 14 and the clients machines being under Windows 7 and Fedora 14.
Quite often I get some difficulties for the clients to get an IP address from the dhcp server. If I look at the server logs, it looks like the server sees the requests and sends and answer:
Apr 12 19:33:18 dhcpd: DHCPDISCOVER from 00:21:70:c5:22:4e via eth1
Apr 12 19:33:18 dhcpd: DHCPOFFER on 192.168.28.52 to 00:21:70:c5:22:4e via eth1
Apr 12 19:33:23 dhcpd: DHCPDISCOVER from 00:21:70:c5:22:4e via eth1
Apr 12 19:33:23 dhcpd: DHCPOFFER on 192.168.28.52 to 00:21:70:c5:22:4e via eth1
Apr 12 19:33:33 dhcpd: DHCPDISCOVER from 00:21:70:c5:22:4e via eth1
[Code].....
I had 200 workstation with both Windows XP and SuSe Enterprise Linux. Sometime, a few clients can't get IP address from DHCP with SuSe OS. With the same computer, if I reboot and chose Windows XP, it work fine. The log message or the boot message was "No IP Address yet ...backgrounding". I tried to reconfig network device, restart services, change another port, change another line LAN, set static IP Address .... but there's no luck for me.
View 5 Replies View RelatedI have a Debian VM on Windows that is not getting an IP address assigned by the DHCP. I tried, ifdown eth0 and then ifup eth0 and still no IP address. my interfaces file looks like this:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
[code]....