My computer won,t boot up anymore, i keep getting the following mistake message: Unable to enumarate usb device on port 2. Don,t know how to skip that, and continue to desktop.
View 6 RepliesI installed ZTE MF 626 modem in my F10 with kernel 2.6.27.12-170, i run usb_modeswitch and so far things happened normally. Watching through /var/log/messages it says that F10 detects two port device for this modem: ttyUSB1 and ttyUSB2, and in the sequence it disable port ttyUSB1 BUT Network Manager still set this port.I mean, when i connect via wvdial appointing to ttyUSB2 i get connection, but Network Manager fails to do it appointing to ttyUSB1. How to change device port in Network Manager?
View 1 Replies View RelatedDoing a dmesg I can see following lines
[ 130.876406] hub 1-0:1.0: unable to enumerate USB device on port 4
[ 130.876453] usb 3-2: USB disconnect, address 6
[ 131.200399] hub 1-0:1.0: unable to enumerate USB device on port 4
[ 131.396382] hub 1-0:1.0: unable to enumerate USB device on port 4
[code]....
That is what I have exactly pluged, the webcam on the top of my screen and an external mouse. Btw, I can plug USB devices with no problem, so I am skiping this error since long time ago, but I don't understand this message and I would love to do it.
I installed Ubuntu 9.10 to my USB-HDD. After upadte, ubuntu can`t load with error:
usb 5-1: device description read/64: error -32
usb 5-1: device description read/8: error -71
hub 5-0:1.0: unable to enumerate USB device on port 1
The boot stopped after this strings.I reinstall the system, and I have this problem again.
i have this error in my log but i don't know why?
Quote:
Jun 19 20:34:08 localhost kernel: [352155.875643] hub 2-1:1.0: unable to enumerate USB device on port 2
Jun 19 20:34:08 localhost kernel: [352155.851515] usb 2-1.2: new low speed USB device using ehci_hcd and address 17
Jun 19 20:34:08 localhost kernel: [352155.677964] usb 2-1.2: device descriptor read/64, error -32
Jun 19 20:34:08 localhost kernel: [352155.503404] usb 2-1.2: device descriptor read/64, error -32
[code]....
The Motherboard is a Intel Desktop Board DH55TC, Sockel 1156, mATX, HDMI
After installation I boot a few times and used F15 on my Dell Inspiron 1564. But now I can't boot anymore. The screen just shows "unable to enumerate USB device on Port 4" and just hangs there with a blinking cursor below that line. I have no USB devices attached though.
View 2 Replies View RelatedI'm running Slackware 13.37 64 bit. I run it on an HP2945SE AMD Turion x2. I am getting an error during boot up unable to enumerate USB device on port 5. It filters throughout the rest of the boot up commands / results. It doesn't seem to matter if things are plugged up to the USB ports or not. Also it doesn't seem to affect anything on the computer. Its just irritating.
View 2 Replies View RelatedRecently my Ubuntu 10.04 was booting slow and to figure out what was going wrong, I booted Ubuntu in text mode. There I found it was hanging on for 5-6 sec showing "unable to enumerate usb device to Port 1". I know it has something to do with Port1 / usb device, but could not understand and solve it.
View 3 Replies View RelatedStartup script. I have a problem with an error on system boot:
hub 2-0:1.0:unable to enumerate usb device on port 5
This error is continuous, filling up my system logs. It is also a known kernel bug. I found a solution here: [URL] but it is only good after I boot. I have tried to make a startup script in /etc/init.d in the following manner.
sudo mkdir /opt/usb/
sudo gedit /opt/usb/usbproblem.sh
#!/bin/bash
# chkconfig: 345 91 19
# description: stop usb problem on startup
case $1 in
*)
echo "fixing usb problem"
cd /sys/bus/pci/drivers/ehci_hcd
sh -c 'find ./ -name "2-0:1.0" -print| sed "s/.///">unbind'
cd ~
esac
exit 0
#End of boot script
##
sudo cp /opt/usb/usbproblem.sh /etc/init.d
cd /etc/init.d
sudo chmod +x usbproblem.sh
sudo update-rc.d usbproblem.sh defaults 92 20
but it does not work.
I just compiled my first own kernel (I'm using Arch Linux), following the tutorial on the german site. Now I tried to boot it, I ended up failing with this message: Code: Waiting 10 seconds for device /dev/sda1 ... Root device '/dev/sda1' doesn't exist, Attempting to create it. ERROR: Unable to determine major/minor number of root device '/dev/sda1' Here is the important part of my menu.lst:
[Code]....
I simply copy&pasted the Arch-entry, i.e. I also had the disk by uuid there. The failure message was the same, just the root device name was the different name Also, at first I did not have the initrd line in my menu.lst (as written in my tutorial that I may not need it). In this case I had this error message:
[Code]....
Getting this constantly in messages:
Mar 13 18:33:26 cjbLT2 kernel: [ 7523.361079] hub 4-0:1.0: unable to enumerate USB device on port 5
Mar 13 18:33:26 cjbLT2 kernel: [ 7523.567075] hub 2-0:1.0: unable to enumerate USB device on port 5
Mar 13 18:33:26 cjbLT2 kernel: [ 7523.739110] hub 4-0:1.0: unable to enumerate USB device on port 5
Mar 13 18:33:26 cjbLT2 kernel: [ 7523.945101] hub 2-0:1.0: unable to enumerate USB device on port 5
[code]....
This is on my laptop. I have 3 external USB devices plugged in but this will happen when I boot without them plugged in too. Don't seem to be missing any device either. This wasn't happening on openSuSE 11.2 and just started when I upgraded it to 11.4.
Reboot and select proper boot device or insert boot media in selected boot device and press a key. I got this error after: Reducing my Windows 7 partition by about 100gb. Creating a new partition (100gb) and copying my Ubuntu partition (10gb) to the new partition. After it was copied, and pasted, the original partition was deleted. I now had two partitions a new 100gb Ubuntu partition and a 600gb (or so) Windows 7 partition.
All of this was done using a bootable USB with Ubuntu 10.10 and GParted partition editor. Now when I boot I get the "Reboot and select proper boot device or insert boot media in selected boot device and press a key." error.
I installed Centos 5.4 on my Pentium E5300 new comp, but I need IPX support in my work. It's simple - ipxutils and ncpfs from Fedora Core and new kernel with ipx support. I copied kernel config from /boot folder and activate ipx, ntfs support, and choose processor core 2 duo. New kernel (2.6.26) works OK, but I got one problem - when start it still shows message: "kernel: HUB 1.0:1.0 unable to enumerate USB device on port 1 (or 2, 3)" and stops after logging (text mode)
I got 2 USB devices connected - printer HP D5160 PhotoSmart and Scanner A3 USB Mustek, and I know scanner cause that messages but I don't understand why. Kernel config is the same like that from distro kernel (almost - ipx, ntfs and proc), but distro kernel doesn't do that. So I got 2 questions:
1. Why
2. What to do to stop that (disconnecting devices on boot time is not a solution)
I'm not that great with mailservers, and just been thrown a curveball with a MS Exchange environment for which there is apparently no solution... yeah, right. But is there a workaround?
The problem is that the site mail (SMTP) needs to be sent via port 26 instead of the commonly used 25. Port 25 is mapped to a mailfilter, which apparently causes havoc with some of the mail, and the techs that have been on site trying to coax the Exchange server to co-operate have said that the only way would be to get rid of the filter.
The problem is that there are number of apps that are unable to have the outgoing port changed and so keep sending mail out on port 25.
I look after the Unix/Linux side of things at work, and I was wondering if there was an easy way to set up a Ubuntu box to receive mail on port 25 and just forward it to the MS box on port 26? So, in other words (and I hope this makes sense): monitor port 25, and forward whatever comes in on port 25 to the server on port 26. Simple portforwarding, or is it? What steps do I need to take?
All my music editing software programs say, "unable to open device /dev/dsp.Device or resource busy." How can I fix this?
View 3 Replies View RelatedI have a host and a client both running linux. Host has internet through eth2. Client needs to share that connection. The computers are connected directly using a crossover. I can ping from both fine. I figured I needed to port forward eth2 to eth0 to gain internet access in the client. How?
Code:
eth0 Link encap:Ethernet HWaddr 00:26:18:a6:fd:a3
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::226:18ff:fea6:fda3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]...
been trying to use a rs232 device that uses the usb port. it calls for a virtual com port to be created. i am running on ubuntu 10 and get hella confused with the search results i have come across.some call for the usbdevfs which apparently doesn't exist under lucid. another had me do use some "magic" in getting it to work.they provided a script mountusbfs.sh
Code:
#
# Magic to make /proc/bus/usb work
#
mkdir -p /dev/bus/usb/.usbfs
[code]....
of course when i tried it the domount command doesn't exist so i modified the above script replacing the domount with mount and it seemed to do something things. usbview is specified as the determining factor whether or not you have the usbfs mounted properly. it wants to use proc bus and ubuntu doesn't use that anymore apparenlty. i have read that i need to enable a usbmon (flag?option?) in the kernel to be set. which it isn't when i followed the steps to check.
I am trying to use the printer port. But, I get this
Code:
Broadcom EJTAG Debrick Utility v1.6r-hugebird
Failed to lock /dev/parport0: No such device or address
johnh@tux:~/Ubuntu One/hh$
run from johnh I permission denied sudo-ing I get above.
tell me detection code of device when an external device is connected through USB port.
View 4 Replies View RelatedI am building a custom RedHat+<our-software> installer iso for our own appliance. I am using Red Hat 5.4. The appliances has two on-board eth interfaces. On the back panel of the appliance, these ports are marked 1 and 2. When I install RH, I find the device names assigned such as eth0/eth1 are arbitrary. I understand this is to be expected with kernels 2.6+. Most of our customers connect their eth cables to the port marked 1 on the back and assume they should configure eth0 to make the device reachable. However, sometimes port 1 gets assigned "eth1". This is not a blocking issue, but its going to confuse our customers and we wanted to make it easier on them.
From reading online discussion boards, I know HOW to switch the assignment of the eth names. However, what I am do not know is whether I need to switch them at all. So I have two questions
1) Is there anyway for me to tell which eth mac corresponds to which port on the back? Since they are soldered on the motherboard and not movable, I would think there would be some way to figure out that x mac address corresponds to the upper port (marked '1' etc).
2) Is there a way to tell this by running a linux command? We need to do this automatically so I need to be able to figure it out at install time from the kickstart post-install or similar.
i want to secure the USB port by any external device connection. so i need the code of detection of an external device when plugged in the USB port.
View 1 Replies View RelatedAfter new installation of slackware 13 when I plugin usb device in the usb port it's print error:
And I have not premission on the device and I must mount the device handle. I
If I forward port 5764 to port 80 to my VOIP device, I can nmap and get a proper connection. If I forward port 5764 to port 22 to my server, it comes up filtered. It even happens if I try forwarding port 80 to my server. So I'm sure it has something to do with my server, but I'm not sure.Here's my Linksys iptables:
Code:
:wanin - [0:0]
-A FORWARD -i vlan1 -j wanin
[code]....
I want to install a TUSB3410 USb to serial port device on suse 10.3.
View 1 Replies View RelatedI have (at least 4) native USB ports that contain flash drives. I know that the /dev/sd[abcd] devices are created in the order they were inserted, but say you have all four plugged in at boot time, or further, they can be plugged and unplugged in real time. At times, /dev/sdf, /dev/sdg, etc. are created as well. I'm ignoring external hubs for now.
I need to know which drive is plugged into the "top port on the front panel", etc, by physical location. From dmesg I can check right after booting and get the physical assignment of a PCI device, say, PCI 0000:00:10.3, as being assigned to the EHCI usb bus. From /proc/bus/usb/devices, and the "T:" field, I have learned that the physical connectors I'm interested are known as USB Bus 1, Port=00, Port=01, Port=04, and Port=05.
From lsusb I can see all sorts of information from the USB point of view, but with no /dev/sd references.
From /proc/scsi/scsi, I can see what scsi devices have been created, with a count consistent with the number of flash drives plugged in, but no USB data.
So, I can get lots of information from the USB storage point of view, and lots of information from the SCSI point of view, but nowhere can I find how to correlate them. In other words, if I want to mount the drive plugged into a given physical slot, how can I find the /dev/sd device I need to mount? udev isn't really interesting here, because I'm just looking for the information that udev would use to answer the same question.
I've done some heaving exploring in the /sys and /proc filesystems and have not yet found where the USB and SCSI worlds intersect.
The closest I have found is (where "Port" is the physical port number from above):
This seems to have some mapping to the physical port and references a "/dev/sd[a-z]" value, but I don't know how reliable it might be, nor do I know if my having to increment that physical port by 1 is meaningful. Anyone have a simpler approach?
So, my goal becomes
mount /dev/<sd that was created for the top slot> /mnt/top
mount /dev/<sd that was created for the bottom slot> /mnt/bottom etc.
I want to do a simple port redirect, i.e. whatever comes trough whatever interface on port AAAA will get redirected to port BBBBI thought that iptables -t nat -I PREROUTING --source 0/0 --destination 0/0 -p tcp --dport AAAA -j REDIRECT --to-ports BBBBhowever it doesn't work, e.g. nc -v -w2 -z localhost AAAA gives:
nc: connect to localhost port AAAA (tcp) failed: Connection refused
while
nc -v -w2 -z localhost BBBB
[code]....
Installed ubuntu 10.4 over previous ubuntu on Intel 945G. After installation and reboot the system does not boot: "no bootable device - insert boot disk and press any key".
Installation was done from USB-stick, prepared by UNETBOOTin. I have two HD's, one used for system + storage, another one just for storage. I manually deleted previous system partitions of previous ubuntu install in system HD. The system HD had about 1/3 of free and unallocated space for system partitions, which ubuntu installer created during the installation.
I tried to reinstall grub from bootable USB-stick and it succeeded but it did not help. The system is still not bootable.
I have used ubuntu for years and never happened something like this. Am I missing something or is ubuntu missing something???
HW failure is ofcourse possible but I am quite skeptical about it because Live ubuntu from USB-stick works well.
I am having an issue with a VCP USB device not working. I know the device works ok on XP. When I check the USB drivers I get the following response (device in question is FTDI Serial in/out).OS is Ubuntu Studio 9.04 new install. I should add I'm not experienced with Linux and command line use but willing to learn. Device issue highlighted in bold.
user-laptop:~$ dmesg | grep -i usb
[ 0.773442] usbcore: registered new interface driver usbfs
[ 0.773476] usbcore: registered new interface driver hub
[ 0.773525] usbcore: registered new device driver usb
[code]....
i had a working multi-boot system, vista on sda1,2; swap sda3; ext=sda4; ubuntu sda5; fedora sda6; data sda7 - i mount the data partition when using all of the linux releases so i don't have to have multiple copies of music, docs, etc. everything has worked fine until yesterday. i tried to install fc12 on sda6, replacing fc11. it required me to format sda6 as ext4. i wasn't sure where i had grub installed, but have a backup of menu.lst in data (sda7), so figured i could let it install to mbr or wherever it wanted to by default. when the install completed and i reboot, i get a black screen and these messages: CLIENT MAC ADDR: 00 19 XX XX XX GUID: XXXXX PXE-E53:
No boot filename received
PXE-M0F: Exiting Intel Boot Agent.
No bootable device -- insert boot disk and press any key I tried reinstalling fc12, same exact errors. I then thought maybe the problem had something to do with ext4 partition mixed in with ext3's, so i installed mepis on the sda6, and let it write grub to mbr (i think, not really sure where it wrote it). anyway, i still get the identical black screen. no grub type menu or anything. the screen used to show "DHCP for a few seconds", but doesn't anymore after i disconnected the ethernet cable.........
I am using a F232 USB to serial adapter for connecting my wireless modem to my laptop and I wrote a simple C code for reading data received by the modem transmitted by another modem installed on my target device.The problem is my code is simply giving 0.00000 (float data) output .When I use the same code with my desktop its running fine and I am getting relevant data.What may be the problem? I even changed the permission for my /dev/ttyUSB0 I am using Ubuntu 10.04 on both my laptop and desktop
below is my code
Code:
#include <stdlib.h>
#include <math.h>
#include <errno.h> /* Error number definitions */
#include <termios.h> /* POSIX terminal control definitions */
[code]....