says wireless unavaliable, do a ifconfig and it doesn't show up.
need to restart computer to get wireless back.
or even a command to run to restart the wireless (/etc/init.d/networking restart doesn't work)
wireless chip: RT2500
networking stops working after suspend/hibernate on Ubuntu 10.10 and it used to happen on 10.04 though i did not bother to resolve the issue then
output of sudo lshw -C network
*-network DISABLED
description: Wireless interface
product: AR9285 Wireless Network Adapter (PCI-Express)
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:08:00.0
code....
I recently installed 10.04 and everything Just Worked.Before Lucid, I was using 9.04 and had successfully gotten my Broadcom 4306 working perfectly... which is why I think the Lucid install went so perfectly.Well, after a botched hiberation (Dell Inspiron 9100), my wireless is dead in the water.I've tried "ifdown", "iwconfig", "/etc/init.d/network restart" and "force-reload", 'modprobe -r b43'
View 1 Replies View RelatedI'm having some problems with wireless, it works fine on boot but after a while pretty much randomly, it can be a few days or it can be a few hours, it stops working. I'm not sure which command would tell you what and it would take a little while to debug it because like I said it's random, but if anyone knows what to do please tell me! I'm on Lucid Lynx 10.04.Another something that's really bothering me (But not related to wireless) is that for some reason when I restart my computer, the top panel keeps changing the applets locations.
View 9 Replies View RelatedRecently I have been having issues with wifi. I can connect for about an hour and then after that the computer stays connected to the network but wont allow me to go anywhere on the internet.
View 1 Replies View RelatedThis should be easy for the Ubuntu Gods to sort out:
I have a Sabrent USB 802.11N adapter. (I am using 64-bit Ubuntu in all below)
I plug it into a 9.04 box and it works fine. Plug it into a 9.10 box. Network manager sees it and can attach to the network, but has 0% signal strength, no internet.
Rebuild the 9.04 box with a fresh install to 9.10. 0% signal, no internet. Try 10.04 Alpha 2, 0% signal strength, no internet.
Rebuild same box down to 9.04. Works perfectly. 100% signal strength. I do all updates and then the upgrade to 9.10 using the USB. Everything works fine until the reboot. Then, USB connects, but 0% signal strength, no internet. Oh! ifconfig says the wlan0 interface is up, but it has a random ip address.
I don't mind using 9.04 because for the forseeable future, the box is just going to count aliens for Seti, but my wife wants it off the counter and I would like to upgrade someday.
My Ubuntu when i start it up, go to the wireless networks , try to connect to my network it trys to connect stops than says disconnected. My internet card is a Cisco Aironet wireless (idk the model number)
View 1 Replies View RelatedI have a wireless network using this driver:
Bus 001 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
and everything works fine for some time. After a few hours or maybe less (if I push bandwidth to the limit) the Internet freezes. I can't even ping my router. If I disconnect and reconnect either the device or the connection via network manager , it does work for a minute only and then freezes again. If I restart Ubuntu entirely, it works again. But for a while...
It works 100% in Win7 and I have no problem at all there. But I am very annoyed that I cant have reliability in Ubuntu. I want Ubuntu as default.
It has something to do with drivers or an inner variable or buffer or something.
At least, is there any way to reset my network connection without rebooting the OS?
I tried sudo /etc/init.d/networking restart but it gives me: Ignoring unknown interface wlan0=wlan0.
I'm running Ubuntu 10.10 Maverick Meerkat 64-bit on my desktop with a wired internet connection (with no firewall). For the past 2 days, I have observed that1. Firefox randomly throws up errors like "Problem loading page" whenever I click on a hyperlink. When I click on Reload, the page loads up just fine. This has been happening a lot recently..and I do not remember updating anything consciously. By the way, ipv6 is disabled in Firefox.2. The network stops working all of a sudden (usually indicated by the Firefox error). The Autho Eth0 indication is active, but I am unable to connect to any external machine.
3. Needless to say, this error is manifesting itself in apt-get as well. I get "something wicked happened" errors all the time, and am unable to download or install anything.That this is not a problem with the ISP is obvious because I also have Windows (from which I'm typing this, ironically), which is able to access the internet.Is this a bug in Ubuntu 10.10?
I'm using Fedora 14, 64-bit. My wi-fi adapter is Intel 5100 AGN on a Lenovo laptop. The wi-fi router is Zyxel. From time to time, I'm getting a black message, that a kernel component has crashed (or something similar). Here are the error details:
Package: kernel
Latest Crash:Sun 20 Feb 2011 04:27:54 PM
Command: not_applicable
Reason: WARNING: at net/wireless/core.c:633 wdev_cleanup_work+0x52/0xbd [cfg80211]()
Comment: None
Bug Reports:
In most cases, after that, I'm loosing the internet connection. I can't open any website, can't ping the router (which is my default gateway) and now it happened even without any error, which really pissed me off. Logging out and back in doesn't help, I need to make a full reboot to get back my internet connection.
Under Windows 7 everything is working fine and I'm not having any trouble with the internet connectivity! I had Fedora 11 32-bit before and it was also working normally!
Initially it was working fine after fedora 15 install.However recently it simply stops responding after a period of time.After reboot, sometimes it does repair itself but again stops working after some time.I'm not aware of any package updateperformed or configuration change that would have impacted it.And it does work intermittently as mentioned above
View 2 Replies View RelatedI have a problem with my wireless connection in ubuntu (natty with amd64bit) There seems to be intermittent disruption in my connection. Havent seen a pattern as yet, though it happens once a day. After that I cant get it to work at all and only restarting + reconnecting the USB device helps. Dont know what is going on.I have already read these pages : Commands and Wireless Troubleshooting.Here is my line of though1) Given that I am able to connect other devices to it while I am not able to connect through this desktop, I think the router is OK.2) I am able to work with it after restart + re-connection . And so the driver is OK and is loaded. The driver seems to be oK and loaded even while I am not able to connect.So why is this happening and how can I get this under control without having to reboot and re-connect the device everytime.Here are the output for the commands which will give you a more detailed idea of the process. Before reboot while I was not able to connect:
Code:
Script started on Tue 23 Aug 2011 01:40:08 PM CDT
raja@UshRaj: ~raja@UshRaj:~$ sudo nm-tool
[code]....
Im having problems with Ubuntu 10.04. My wireless disconnects frequently and firefox seems to stop working. it seems the connection times out sometimes when firefox stops. other times the connection just disconnects. When I was running 9.04 everything worked and nothing disconnected, so I know its not my computer.
My laptop is an IBM t40, 1.4 ghz, 2gig of ram.It does not seem to mater if Im using the wireless or the wired connection. The problem happens either way.does anyone have a solution for this?
My Acer's Wireless randomly stops working until you fully shut down and start the computer.(Not Restart but Shutdown->Powebutton) I am using Ubuntu 10.04 Lucid.
I am wondering if anyone knows why it would stop working properly, and/or how to fix it?
And since this is a off and on problem I might not be able to provide details immediately from time of crash, since I need my computer on the wireless.
One symptom that really stands out is that the cooling fan is spinning as fast as it possibly can and processor usage is spiking around 80/200 on a process called phy0.(relevancy unknown)
As I was typing this post on my other computer, my laptop crashed and I lost the lshw -C Network output I had. If asked to, I will post the one from when it is working. Also I will post any other info you need from when I can.
I'm running a Source Dedicated Server on my Ubuntu laptop, and to connect to it via external IP from other computers in the network I need to enable loopback in my router.This was working fine, but then I disconnected my laptop for a few days, and when I came back the wireless stopped working on my Xbox. I reset the router to factory defaults, and then setup everything again. It was all working fine until I enabled loopback again and power cycled my router. Now every time I do that, the internet on Ubuntu stops working and the wireless on the Xbox stops working.
Edit: You can ignore this I guess. It seems I was actually DISABLING loopback by enabling that router option, which I guess caused this. Strange, because the first time enabling this option was the only way to get my external ip to work. Oh well, everything is fine now.
I use a Kensington Wireless Netbook Mouse.It has worked well in Ubuntu 9.10 and 10.04.For some reason in 10.10 it works, but every now and again it sticks for a second or two. Sometimes the left button stops working.If I pull out the dongle for the mouse and put it back in my mouse works fine.
View 3 Replies View RelatedTesting distribution. Installed Linux 3.0 but left 2.6.32 on as backup. When I boot into the old kernel, wireless mostly works OK, but never when I boot with the new kernel.
Results of dmesg|grep wlan0 on 2.6:
[ 22.005102] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.196774] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.644779] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 30.688053] wlan0: direct probe to AP 00:19:5b:06:9f:ba (try 1)
[ 30.694053] wlan0: direct probe responded
[Code]...
Noticing the Access Point looked like it needed the MAC address, I ran iwconfig wlan0 ap <MACADDRESS> and sometimes it will work, and wicd can connect to the access point. But sometimes the command fails to run.
I upgraded from 9.10 to 10.04 and my wireless card no longer works.
The card is a Dell 1450 USB a/b/g card.
lsusb sees the card. device id is 413c:8104
dmesg says that p54usb is trying to load firmware isl3887usb but that failed (error -2)
I looked in /lib/firmware and didn't find that file
ps. god why did i upgrade?
I have a Dell E6500 with and Intel 5300 wireless agn card running Lucid x64. Wireless works fine and speeds are great except when I download with either the browser or thru a torrent or even updates. Once I get to around 100 megs in to the file wireless stops working and the only way to get it working again is to disconnect and reconnect to the AP. I have installed the back ports and tried several other fixed to get this to work but nothing has helped. One more note this happens on 2 other wireless routers that I have tried so I know that it's not limited to my Linksys.
View 3 Replies View RelatedI have one major problem that is going to cause me to switch back to windows. My wireless network shows connected and works fine for a while but periodically stops working. It always says it is connected but sometimes stops working to where I have to disconnect and reconnect for it to start back up again.
View 9 Replies View RelatedI have problem with resuming after hibernate, it is about 50% chance that computer restart when I want resume, then it starts boot normally and all my work is lost.
Acer aspire 3820tg
Ubuntu 11.04
Builtin hibernate on partition
I try uswsusp s2disk ... on resume it always stops in half of process. I used mainly hibernate, but I'm lost now.
Im having an annoying problem here, after the reinstallation of opensuse, bluetooth works fine, i can connect my cell phone and logitech mouse normally, as soon as i install the bcm43xx from the scrtipt included in /usr/sbin/ bluetooth stops connecting to devices, it can find tem when searching but the forward button is dimmed.
when i try hcitool scan,= it successfully finds the device,
hcitool cc xxxxxxx it reports an I/O error,
I am currently dual booting between Linux Mint 10, and Windows Vista SP2. Wireless works fine in both these OSes, but when I quit Mint and load Windows, 70% of the time my wireless stops working.
ie, it does not detect any wireless networks nearby, althought there are tons of them.
Restarting the wireless device doesnt help, I have to restart my computer at least 4 times for wireless to start working again.
And as of now, my wireless in Linux Mint has stopped working.
My wireless LAN connection on this machine occasionally stops working. The network traffic bar shows periodic very small transmissions but the failure of all network dependent applications (Firefox, package manager, etc.) indicates to me that the machine is no longer talking to the net. I can fix it by reselecting my home network in nm-applet from the drop-down list. This causes the machine to disconect, reconnect and all is well for some random period of time thereafter. Here's some data:I'm running an HP Pavillion laptop.
Code:
~$ lspci | grep Wireless
02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Code:
~$ lsmod | grep iwl
iwlagn 124768 0
iwlcore 134820 1 iwlagn
mac80211 243496 2 iwlagn,iwlcore
[code]....
I don't know if this is related or not, but a couple of months ago I unsuccessfully attempted to share a hotel's wired Internet connection over my wireless card. I may have hosed some settings or it could be unrelated.The "unknown interface" portion of the restart attempt is interesting but I don't know enough to fix it.
I'm using a Vaio TT, which seems to use an Intel 5100 WiFi chipset, and a Linksys WRT54G2 (firmwares 1.0.1 and 1.0.4), ubuntus 10.10 and 10.04.
Wifi works fine out of the box. However if the other vaio tt in our office (running windows 7) comes online, my laptop stops being able to make new connections. It WILL stay connected to chat servers, and downloads SOMETIMES continue to work. However all new HTTP requests / ssh connections / rdp connections / pings fail. The laptop still appears to be "connected" to the wifi network.
This may also happen after an undetermined amount of time without the extra vaio. It is not solved by reconnecting or rebooting. Once the extra vaio leaves the building, everything works fine again. This problem does not happen at all if I boot into windows.
I'm moving from other distros. and I'm currently loving openSUSE and I'm probably going to stick with it for a long time.I have already googled for this, but I found no solution, but I figured this should be a common problem... Does google searches inside this forum?Now... for my problem, whenever I hibernate (suspend to disk) or sleep (suspend to ram) I can't resume my wireless connection nor connect to another.I don't know if this is an issue if I use cables, because I simply don't with my netbook:The hardware in question is an ASUS 1005HA eee pc, running openSUSE version is 11.3 fully updated. Didn't mess with wireless connections, nor kernel or hibernate settings
View 9 Replies View RelatedI fixed my wireless driver, turned on power management, and, that keeps getting reset to the defaults after sleep or hibernate (KDE control panel). There are many places to hard code fixes like these, but, is there some place dedicated to post-restore scripts? I don't want to put my script somwhere that it's going to get clobbered on a system update.This system really needs an /etc/rc.local anyway. Can I just create one and put it in the string of things to run at transition between runstate 3 and 5? Will that always get run with the powermanagement stuff?
View 1 Replies View RelatedSometime after I upgraded to ubuntu 9.10 I've been having trouble with my wireless network connection.It will usually log on to the network, then disconnect a shortly after. Then try to connect again, usually successfully, then it cuts off again. Then connects again, then disconnects. FWIW, ubuntu 9.10 works on a different machine pretty consistently, so I don't think its a problem with the router.
View 2 Replies View Relatedjust completed an new install of 11.3 on a laptop and have a couple of wireless config questions.the wireless is set for ifup mode and have been using iwconfig to set the ssid. is there a preferred way to automatically set the ssid? something that avoids setting a fixed ssid in ifcfg-wlan0. this laptop had 10.3 and to restart the network after wake-up from hibernation i had to run a script from pm-utils/sleep-d. it looks like i may have to do the same for 11.3. or does 11.3 have a better way?(NetworkManager in 10.3 gave me all kinds of grief, so i stopped using it. perhaps it is improved in 11.3, but i have not given it a chance.)
View 1 Replies View RelatedMy suspend and hibernate buttons are not working. When I try to return from a suspend, I do not get a kernel panic, but nothing loads onto the screen.
View 7 Replies View Related