So i just installed Ubuntu on my computer,the first thing i noticed was that my resolution was 800x600. i had used 1280x768 on windows. but when i tried to change the resolution i can't change it. its only limited to 640x480, so how do i change it to 1280x768?
View 9 RepliesI am having a major problem in a new Karmic install. Big rationalisation. Kicked out a lot of machines in favour of Virtual machines. Installed Karmic. Machine has dual 22" wide screen monitors, max res 1680 x 1050. Karmic installed at maximum 800 x 600 and will not go above that. I have looked for xorg.conf and cannot find one anywhere. I have tried the randr as shown by Sharaq but when I try to set the higher resolution it gives message saying maximum size is 800 x 600. I have downloaded the proprietory drivers from Radeon and tried to run them. The installer runs but I cannot get to the 'Continue' button because it is off the bottom of my screen so I cannot set up the drivers. I suspect I am going to have the same problem with the Lucid install I did yesterday. Earlier releases never gave me this issue so why now?
Why is the initial resolution so low?
My machine is dated, that's for sure, but it's never given me problems. Ubuntu has worked flawless until the 10.04 update. Now I'm not getting my proper screen resolution of 1024.768, and Ubuntu won't recognise my screen. Also, when I try to load up my nvidia drivers on the Hardware Drivers app, and reboot the computer, when GDM loads I get an error that the nvidia module fails to load, and there is no such driver.
View 6 Replies View RelatedI have recently installed Ubuntu 10.04 beta version. After installation, my laptops screen resolution cant be increased to 1024x768. More over i cant see that 1024x768 option in the System>Prefrences>monitor option.
View 4 Replies View Relatedhere is output of lspci
Code:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 21)
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC
[Code]...
Just Installed the latest version of Ubuntu Netbook on my Toshiba Portege 7200 and the screen resolution is set to 800x600. The OS is not recognizing the fact the laptop can do 1024x768. I've been searching the net for a few hours to fix the problem and I'm not getting anywhere. The fix to the problem is to add the info below to the Xorg.conf file. This file does not seem to exsist on the latest version and if I create it manually it does not work.
# xorg.conf (X.Org X Window System server configuration file)
# This file was generated by dexconf, the Debian X Configuration tool, using values from the debconf database.
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
# This file is automatically updated on xserver-xorg package upgrades *only* if it has not been modified since the last upgrade of the xserver-xorg package.
# Note that some configuration settings that could be done previously in this file, now are automatically configured by the server and settings. Here are ignored. If you have edited this file but would like it to be automatically updated again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Device"
Identifier "Trident Microsystems Cyber 9540 (rev 52)"
Driver "trident"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "Integtrated LCD"
HorizSync 28-90
VertRefresh 43-85
#Modeline "1024x768_60.00" 63.50 1024 1072 1176 1328 768 771 775 798 -hsync +vsync
#Option "PreferredMode" "1024x768_60.00"
EndSection
Section "Monitor"
Identifier "VGA-0"
Option "Ignore" "true"
EndSection
Section "Screen"
Identifier "Screen 1"
Monitor "Integtrated LCD"
Device "Trident Microsystems Cyber 9540 (rev 52)"
EndSection
I have a problem with the screen resolution in that most of the time it defaults to 800 x 600. However on occasions when I switch on the resolution increases however just today when it happened after typing in my password it refused to log me in.
Before anyone asks my password is in lower case and the NUMLOCK is off and I know I'm not mis-typing it.
here's the strange bit, when I reset the computer and the resolution goes back to 800 x 600 it then accepts my password. go figure!
I have installed Lucid on a PC with integrated graphics (GeForce 8100 on a Biostar GF8100 M2+ TE). On a fresh install the resolution is 1024x768, but that's no surprise as the Nvidea drivers are not installed. Immediately I get a notification of HW drivers available. I install the latest (recommended) ones (195.36.15). Reboot, and I can see other resolutions available:
1152x864
1360x768
I'm using a 19" Dell LCD (4:3 ratio) which supports up to 1280x1024. I can actually set the 1360x768 but, obviously, the screen looks ... squashed in the X axis. I noticed that the type of display is not identified (Nvidia panel says "CRT-0"), so I tried to manually add the 1280x1024 resolution. Below you can find the xorg.conf and the Xorg.0.log. It seems to me that the mode 1280x1024 is considered not valid for some reasons. The string for Modeline in the xorg.conf was determined using "cvt".
Here's the xorg.conf (after a few iterations, it became a bit busy ...):
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder5 Fri Mar 12 02:12:40 PST 2010
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "0"
EndSection .....
I am unable to change mu screen resolution in slackware 12.2. I am editing the xorg.conf in "etc/X11/" with nano. My graphics card is a ATI with 64MB RAM. My monitor is capable of 1280x1024 @ 60Hz. Heres the xorg.conf:
Code:
# File generated by xf86config.
# Copyright (c) 1999 by The XFree86 Project, Inc.
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions: .....
I have a Fujitsu-Siemens V5535 laptop with a SIS Mirage 3+ graphic card, 671/672 chipset. I put ubuntu 9.10 on it, but I am not even able to settle the screen resolution higher than 800/600 . I tried different sollutions that i have found on the linux forum, but I was not successful.
View 1 Replies View RelatedI am using a 15" CRT Samsung monitor and when I upgraded 10.10, the screen resolution became 800x600 and I am not able to increase the resolution of it. This was working fine with 10.04 version.
Below is the o/p for "xrandr":
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 800 x 600, current 800 x 600, maximum 800 x 600
default connected 800x600+0+0 0mm x 0mm
800x600 0.0*
I also see a continuous message box at the top left corner of my monitor with text as "Unknown".
I have done a fresh install of Ubuntu 11.04 on my oem intel machine.After the installation,the screen resolution is stuck at 800x600.I am unable to select a higher screen resolution.
View 6 Replies View RelatedBefore I upgrade to 10.4 It would be nice to find the best solution to this problem. I use a KVM switch that dont pass the EDID info from the screen to the OS. To solve this, that is, to get the correct screen resolution, i need to pass monitor and screen info to the OS at every startup. One way is to ad a script to /etc/gdm/init/default, or in KDE /etc/kde4/kdm/Xsetup.
View 2 Replies View RelatedI recently upgraded my graphics card from a Geforce 7600GS to a Gefore 560Ti. And while most things are normal, during boot up my screen isn't "full screen" until X is started, after which everything else is fine. Essentially, all display, the grub menu, the splash screen, console text, etc, is within a box on the screen, with 2" on the left and right, and 1" top and bottom of empty blackness.
From what I understand, this is because the framebuffer is using the wrong resolution, but the maximum resolution that hwinfo --framebuffer returns is 1280x1024 (which I am already using "0x031a".) (My monitors is natively 1920x1080) Is it possible to do something about this? If not increase resolution than at least stretch the screen to full screen?
sudo /usr/sbin/hwinfo --framebuffer
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.459]
Unique ID: rdCR.GGyCBArXznD
Hardware Class: framebuffer
Model: "NVIDIA GF104B Board - 10400050"
[Code]...
i have just put a Geforce 7300 GT graphic card into my machine the problem is the max resolution I can get is 1024x768 at 60 hz the screen is a benq fp71g+. also the screen goes blank when i click on the display icon in system settings. i know that the screen can be run at 1280x1024 so I don?t know where the problem is.
View 3 Replies View RelatedUnfortunately my experience in the Unix* based world up to this point has only been using web servers and administrating them, no GUI experience of any kind so I am completely unfamiliar with the setup and entire usage of Xorg or any other Window manager at this point. The issue I am having is with the screen resolutions I am being allowed to chose for my Dell Studio 1535 running Fedora Core 13 and the KDE 4 desktop GUI, thus my issue since I am not really familiar with how to run a Unix* based GUI in the first place.
The basic information, if there is more needed just advise what and what command gathers that info (or what conf/log I should look into in order to find it). Laptop is a Dell Studio 1535 Video is the Mobile Intel GMA X3100 ATI Radeon HD 3200 Graphics. LCD interface is the LVDS.
So far it seems to give me modes for 1024x768 and on down, nothing above this. I believe I am supposed to use the radeon driver being that is the type of card it is but every time I change the xorg.conf file to use this instead of vesa the system wont get past the loading screen anymore upon reboot and nor can I seem to find a way to bring up a command line so I can hit up the Xorg.0.log to see what is wrong or change the xorg.conf file back to the original driver it had listed.
I am going to assume this is a missing driver or something else it hangs on but without being able to get access back to the system and having to rebuild it again (re-install via live CD) I am basically out of luck at this time. Sorry for the rather poor post but I do hope to receive some basic directions on where to go from here with this issue
i just installed 10.04.1 and have done a quick apt-get update/apt-get upgrade.the problem is i'm running a 1920 x 1080 display using a geforce gtx460, yet the screen is cropped in at 1280 x 1024. i have the option to go lower only.i first tried to install the nvidia binary in the old-fashioned way of (system > administration > hardware drivers) but this reported that there are no proprietary drivers in use and there was no option to 'switch one on'.i guess my hardware is too new so i want to install the drivers available at nvidia's website (256.44). this adds support for my gpu.
i tried to install these by exiting x but this just resulted in some sort of system hang. the function keys on my keyboard seem to be 'non-functional' too, making a ctrl+alt+f1 not do what it should. i think this may be a problem with the mac keyboard i'm using.is this just a waiting game? can i get into a virtual console somehow else (perhaps during bootup)? is there a way i can exit x without the system hang? is there another way of installing some workable drivers? should i be altering my xorg.conf?
I have a custom PC with a (nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1)) graphics card and a 17" Compaq MV720 CRT monitor. My graphics card/monitor combination is capable of resolutions up to 1280 X 1024.
I just installed Ubuntu 10.10 64Bit, and the highest resolution available at Sysytem>Preferences>Monitors>Resolution: is 1024 X 768. I want to get the resolution up to 1152 X 864, which the card/monitor is capable of. I looked around the forum for a solution, but couldn't find a thread that explains exactly what I want to do. In the most previous version of Ubuntu that I used (9.10), I could generate an xorg.conf with Xorg, grab the (Monitor, Device, and Screen) sections, and use that with a few changes to create an xorg.conf to get the resolutions that I wanted. In 10.10, that no longer works. In fact, it won't even work without the changes. After placing the xorg.conf in /etc/X11, the PC will only boot up to a text CLI prompt to login. No GUI desktop.
My PC is a totally orthodox desktop, no dual boot, no Virtualbox. What do I have to do to get the resolutions above 1024 X 768?
I've installed Ubuntu 10.10 on my laptop, only to find I only have low resolution problem. I got my system info and it's:
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10)
All the tutorials tell me to try and use xorg, with commands like:
Edit /etc/X11/xorg.conf but I always get a response of
Command 'edit' from package 'mime-support' (main)
Edit: command not found
I have installed ubuntu 10.10 yesterday, but couldnt find any option to set screen resolution , from where to set it ?
View 4 Replies View RelatedI'm having problems adjusting my screen resolution. I'm using Nvidia Geforce FX5300 video card and Samsung T220P LCD screen with resolution of 1920x1200. After installing the Nvidia driver I went to system -> preferences -> display in order to change the resolution to 1920x1200. Unfortunately, the available resolutions were only 640x480 and 320x240. I tried to set the resolution manually, using the advanced button, but when I did this everything was extremely big on my screen.
View 1 Replies View RelatedI am running Ubuntu 9.10 on Intel(R) Celeron(R) CPU 570 @ 2.26GHz SIS 771/671 PCIE VGA
have even tried changing xorg.conf
How can I change screen resolution?
View 4 Replies View RelatedBy default, ubuntu is using an incompatible resolution for my monitor. It happens while booting and logging in. It is due to it using a Hz setting to high for the monitor.What can I do to fix this?
View 1 Replies View RelatedYesterday I installed ubuntu 10.04 LTS, it allow me only 800x600, 640x480 and 400x300 screen resolution, how can i set 1280x1024 ?
View 9 Replies View RelatedI'm very new to Ubuntu and have 9.04 running on a Sony Vaio, don't know what graphics card I have. My screen resolution doesn't have an option higher than 800x600, so everything looks super zoomed in. Other threads tell me to edit xorg.conf, which I did (probably incorrectly). The result was the computer had mega problems when I restarted it, and when it finally got back to the desktop it didn't give me any other options for screen resolution. Also it says I'm in low graphics mode.
View 1 Replies View RelatedOn last boot it was fine but now it is showing 800X600 which is too low . How to adjust it
View 9 Replies View RelatedI just want my normal settings back. I deleted the original post because I really screwed something up and I have to use Windows until I can figure out how to fix it. Forget about my resolution preferences. My Linux boot is stuck in low-graphics mode
Would anyone be able to provide me step by step, easy to follow for a newb instructions on fixing my boot?
I have to use recovery mode to load any graphics at all, and it's stuck in low graphics mode and I can't change it. More info below.
I recently upgraded my desktop pc from 10.04 to 10.10 and ran into a tad of trouble. After I attempted to login from the GDM, something caused the system to crash and return to the GDM. So, I got my laptop out, did some googling, and decided to delete ~/.config/monitors.xml to try and reset the resolution. That got me to the Desktop, at which point I was greeted by more display issues.
The point at which the computer normally goes idle seems to crash and return it to the GDM as well. Needless to say, I disabled the idling/password prompt setting to prevent crashes every five minutes. Anyway, the prevailing problem is that I can't change the resolution itself -- as that seems to cause the same issue.
I've recently installed Ubuntu 10.10 on an old Dell computer I have. Everything seems to work fine, but I can't seem to change the screen resolution. In the monitor Preferences it says Monitor:Unknown. It's stuck on 1600x1200 and I'd like it to be closer to 1024x768
I've tried changing the xorg.conf file to no avail. I've been browsing for 3 days now looking for a solution.
[URL] These are my specs if it helps any, ignore the windows installation info because I have it installed alongside ubuntu.