my TV capture card wont even get recognizedit my Windows machine it works finebut here in Ubuntu 9.10 it does nothingit i an older WinTv 150 non-PVRit has the 878 chipset
View 4 Replies
I've no idea what the heck is going on with my TV capture card, i went to the other posts about my Hauppauge Inc. HDPVR-1250 model 1196 but it all didn't work i have the ubuntu-restricted extras installed but mythtv is not picking up the card. i'm running ubuntu karmic.
View 9 Replies View RelatedRecently I had to replace my Hauppauge HVR-1600 (it was doing everything I wanted it to do but after a few years burned out) and decided to get the HVR-2250. Before purchasing I checked the forums and noticed that there was quite a bit of support and most everyone managed to get it working so I thought it would be a good idea.
The problem I have now is that, though lspci shows the card as Multimedia controller: Philips Semiconductors Device 7164 (rev 81); however, when trying to setup mythtv-backend, the card does not show up under the "capture card" section. After a few hours of research, I came across this thread and it seemed to be general consensus that the method worked so I tried it. Still no luck.I ended up formatting, fresh install of Ubuntu 10.10 and then installed MythTV and still nothing. Not really sure where to go from here.
I just installed Ubuntu 11.04. The drive was formatted when I installed so it's 100% Ubuntu. The only major problem I have encountered is that Ubuntu will not recognize my SD cards. I really need to access these cards, all my film footage is on there. I think the internal SD card reader (If such a thing exists) would have been deleted during the installation process. I am a greenthumb to Ubuntu and have never used it before so I am rather stuck...
View 7 Replies View RelatedI have a capture tv card in my pc, but i can't configure it. It's a TV Tuner PRO ENLTV-FM Encore Electronics. I have all the System Requeriments and I've downloaded a program called MeTv to use it, but it's not working. The message that i have of this program is:
Code:
There are no DVB Tuner Devices
I've read on the net that I have to alter something in the kernel called bttv with the
[code]....
Well I used to have windows but it kept crashing and I don't have a lot of supplies for reformatting computers so i went to my super smart friends house (he has everything) and he put Ubuntu on my computer he set it up bbbuuuuutttt he spelled my name wrong I'm not super savvy with computers that aren't windows I've only had windows up to now and the change is kind good but slightly bad I can't find a capture card software but besides that I can't figure out how to change my name on this computer it's something small yes but it's also something that will bother me FOREVER
View 4 Replies View RelatedI have been trying to put together a mythbox for myself. I installed Ubuntu 10.10 and the newest version of the Mythbox backend. My capture card that I am having issues with is a Hauppauge Wintv-HVR-1850 card, I followed the instructions on installation from linuxtv.org and did not get any errors. I tried to set up Mythtv and it didn't get a signal and couldn't find any channels. I would like to know if my card is even working so I tried using xawtv but still could not get a signal from my card.
how I can verify that my card is installed correctly?
i am looking for recommendations for a usb video capture card. i basically want to take co-ax input coming from a cable digital converter box and save the content (mpeg, avi, mkv, ...).
View 5 Replies View RelatedI'm trying to setup Mythbuntu on a computer connected to a TV. I have bought an USB DVB-T Receiver, named WandTV. According to LinuxTV; WandTV, aka Shenzhen Forward Video EzTV859, is supported in the Linux kernel.
When I try to setup the mythTV backend I'm being asked of what card type I have. I guess the answer to that is "DVB DTV capture card (v3.x)", but no matter what I choose, it can't find any devices.
I'm pretty sure /dev/hidraw0 is the receiver, can I use that to setup the backend?
What kind of tuner I need. do I pick up ntsc, atsc, or something else? My cable comes from the wall to the tv, there is no box receiver.
I have had real bad luck with the acermedia duet and the hauppage hvr-1250. Aperently, the aver duet has 0 support and I can't get the hvr-1250 to work. I'm running mythbuntu 10.04. I can't even get avi's I downloaded to play in mythtv.
I previously had my bt878 capture card setup with Ubuntu 10.04 and it worked fine with Zoneminder. However, after having done a clean install of Ubuntu 10.04, the card causes Ubuntu to freeze whenever I attempt to view the image in a viewing program (happens in tvtime, Cheese and Zoneminder)I have added bttv and bt878 into /etc/modprobe.d/options like before, and have also added options bttv card=77 tuner=-1 into bttv.conf in the same directory (had to create bttv.conf)The freeze causes the whole computer to lock up, and nothing on the keyboard or mouse is responsive, and involes having to do a hard restart.The only difference I can see from before, is that I have installed all of the latest updates with Update Manager, so maybe a new update is causing these problems?Output of dmesg � grep bttv
Code:
[ 18.149815] bttv: driver version 0.9.18 loaded
[ 18.149826] bttv: using 8 buffers with 2080k (520 pages) each for capture
[code]....
I'm running VideoLan (VLC) under Ubuntu 9.1 (Karmic) (64-bit) with a Haupaugge-150 card. Right now when I want to get the TV feed in through the coax, I first have to run "ivtv-tune -c3" to set the channel for cable.
I've tried adding a line to the vlc.config but no joy. Googling found an answer for Fedora but it doesn't match the files I'm seeing in those directories for Ubuntu.
What I'd like would to have ivtv set the channel automatically at boot or start-up.
Does anyone know an Ubuntu 10.10 compatible video capture card that has composite connections for video and audio (yellow, red and white)? It must be external and do its own processing so it doesn't use the computer's own CPU. I intend to capture a live stream and have the Ubuntu PC serve it to other computers. I may use VLC or MythTV. I have looked on various related sites but finding a compatible USB one which does its own decoding is hard to find.
View 2 Replies View RelatedI have a pinnacle callisto video capture card which I am having trouble getting to work.
lspci
lsmod - notice that the saa7146 module is not loaded. If loaded manually the card is still not found.
Dmessg does not show the card.
System:
Slackware64-Current multi lib
What would be the easiest method to record video from a security camera via a video capture card using a gui?
I have acquired a Canopus ACEDVio video capture card and can not get it to work.
View 1 Replies View RelatedWe have a webcam that is connected to a tv tuner card via the rca input on the tuner card. I want to set that up so that i can view it remotely over the internet. I've seen you can use vlc to do this, but the problem is that I don't want to have the webcam's computer recording and streaming all the time. I want it to only do that when i want to view it from my remote computer. We don't view the camera at a regular time, so a set schedule wouldn't work.
I hope this all makes sense. Is this possible, and if so, what is recommended for getting this done.I'm hoping i can somehow control this with a remote control and we'd see it on our tv monitor (that'd make it easy for the non-computer people here), so if it could be done in a script that would be great cause i can have the remote run the script.
i installed an nvidia graphics card recently and this
Code:
ffmpeg -f alsa -ac 2 -i pulse -f x11grab -r 30 -s 1024x768 -i :0.0 -acodec pcm_s16le -vcodec libx264 -vpre lossless_ultrafast -threads 0 ./Desktop/mydesktop.mkv
[code]....
I am new here and I have tried checking similar threads as well as other sources in the net but could not get my card working. I use Debian squeeze on a P4 2.4MHz machine with 2 GB ram. lspci can detect all 8 chips but could not load the proper module since it could not identify the vendor. I have tried unloading the SAA7134 module and reloading repeatedly all possible cards from 1 to 174 by "modprobe -i SAA7134 card=#,#,#,#,#,#,#,# #-numbers 1 to 174 one a a time.
View 3 Replies View RelatedI just installed and Ubuntu doesn't recognize my wireless card HP dv2945se. I can get a wired connection. I can't figure out what kind of card I have (did the terminal command line, have no idea how to read it) or how to install a driver for this OS (HP's site just lists drivers for Windows). How to get the wireless card recognized?
View 9 Replies View RelatedSomeone had just given me a pc with no OS so I installed ubuntu 10.04. The pc has a wireless card but I cannot seem to get the OS to recognize it. My wired connect is fine but wireless is non-existent.
View 7 Replies View RelatedI'm trying to proselytize and have installed Lucid on my receptionist's Gateway M500 with an Orinoco PCI Mini wireless card.
The card works in XP, but when I boot into Linux, the network card indicator light doesn't turn on, and lspci gives me this:
No wireless card
Pressing the on-off wireless button does nothing.
What can I do to turn on the modem so that Lucid sees it?
i just thought the last few days about trying Ubuntu. so i did. i got a nice and fresh copy of Ubuntu Desktop version and installed it, everything worked great except my wireless usb 2.0 card. the only internet connection i have under windows is Wifi and i hoped that my dongle will be recognized by Ubuntu automatically...(naturally, it wasn't the case.)
so my adapter looks exactly like this one here, except for the color, it's white and it has my WISP's name written on it (i got it from them, along with a cd that offers win xp/98/me drivers...)
so even everest sees it's atheros and it's the Atheros AR5523 chipset.
i also have windows 7 64bit drivers if they help...
anyway, i can't get it to work and cannot access the internet any other way when on Ubuntu, so i have to use an already-saved driver..
I updated my video card drivers, but when I boot back up, I have no GUI and am given a terminal because it does not recognize the drivers. I have already changed "quiet splash" to "nomodeset" .
Specs:ATI Mobility Radeon 5650
500GB (7200RPM) Hard Drive (SATA)
Intel Core i5-450M processor 2.40GHz with Turbo Boost Technology up to 2.66 GHz
4gb of ram
Ubuntu 10.10
I have lucid installed on my hp laptop without any problems, and I went to install it on another hp but the I can't connect to any wireless network. I tried to follow this thread's advice [URL] . Because it's pretty much the same problem except I think the wireless card is from a different Intel family but it didn't work.
Basically wireless networks won't show up, in fact the network icon only has "wired" as a menu option.
I tried to follow the thread, even though I had no idea what it was saying as far as instruction goes.
The soundcard was working with the exception of the mic.
So I tried to install linuxant drivers and the installation failed for some reason.
So I uninstalled it. After that my sound card is not being recognized.
Here is the output of the alsa diagnostic script.
Code:
What is the best analogue capture program please to capture Austar.
View 1 Replies View RelatedI just installed 10.04 on my EeePC 1000HE, and wireless isn't working. My card isn't listed when I ifconfig. I've messed around with installing the Windows drivers, but nothing has worked so far.
If it's useful, I popped off my battery and it said something about the wireless controller "NE766".
make sound card recognized by alsa?
Code: !!Sound Servers on this system !!
----------------------------
Pulseaudio:
Installed - Yes (/usr/bin/pulseaudio)
Running - Yes
ESound Daemon:
Installed - Yes (/usr/bin/esd)
Running - No
[Code]....
so I had to reinstall Ubuntu.But now my Wireless card won't work. It used to work before (plug and play), and I have no problem with it when I boot from the CD.I cannot use my cable connection because as soon as I plug my computer in, the network crashes, the router doesn't respond, gets hot and refuses to work until I unplug it and let it cool off for 2 minutes.I'm using Ubuntu 10.10, Desktop PC.
Code:
:~$ lsusb
Bus 001 Device 002: ID 0846:4260 Netgear, Inc. WG111v3 54 Mbps Wireless [realtek TRL818B]
[code]....
