whenever Ubuntu boots, it searches for an external hard drive that I no longer have plugged in. It hangs on the Ubuntu load screen for a while, then says that it cannot find the drive and I have to press (S) to skip the attempt.
View 4 RepliesI have installed ubuntu 10.10 on and external usb drive and now my computer which runs XP will not boot unless the external drive is connected and on. Can I by pass this situation or do I have to uninstall ubuntu altogether and start over?
View 3 Replies View RelatedThis sounds strange, but my laptop (running 11.2) won't boot correctly unless my external HDD (ext3) is on and plugged in. If I don't turn it on, it hangs at the start of udev. If I press ctrl+c, the system continues to boot, but the keyboard and mouse don't activate... don't function, etc. But I can press my power button and it does shut down. Going through dmesg (during a successful boot with the external HDD on), I saw this (not sure if it is relevant):
Code:
[2.201029] scsi 2:0:0:0: Direct-Access Ext Hard Disk PQ: 0 ANSI: 4
[2.201450] usb-storage: device scan complete
[2.206637] sd 2:0:0:0: [sdb] Spinning up disk......
[6.062434] udev: starting version 146
[6.225262] .
The device sdb1 is the HDD.
Now, I don't know much about udev. I can tell you that I have no sdb1 lines in /etc/fstab, and I have no autofs references to it.
I been meaning to install some linux distro on my external hdd to enjoy the renowned desktop experience, so far I installed sabayon first but it wasn't working very sharply and a friend of mine recommended me to just install ubuntu. Anyhow, since the first time I installed sabayon I could not boot vista when the external HDD is not plugged in. I get a grub rescue command prompt. I don't have a vista cd because my laptop came with the whole recovery function installed on a vista partition. I can boot that from the grub menu, from there I did a boot system restore, but I still get the same error. I'd like to be able to boot vista without having the external HDD on of course.
View 9 Replies View RelatedI have an Asus eee901 netbook and it's got an Intel 945 graphics card. If I boot it up, log in, attach an external monitor and then open the Display Settings dialog the screen goes black and the laptop appears to crash. Leaving it for a minute or two does nothing.
However, if I boot up with the external monitor attached then I can open the Display Settings dialog and configure both screens.
This is quite annoying as I've got to reboot if I want to connect an external monitor.
Additionally, if booted with the monitor attached and I choose a configuration where the width of the combined screens is greater than 2048, the screens go black and the same lock up appears to occur. Could it be that the Display Settings dialog isn't checking for the maximum display width the driver supports and is then crashing in both scenarios?
I finally got my new internal hdd for my laptop. I plugged it in and installed windows 7 64 bit. Then I partitioned my external hdd (WD mybook 640gb), and installed ubuntu 9.1 on a 200gb partition of it. The problem is that I didn't unplug the internal hdd before I installed ubuntu. Now the computer will not start unless I have the external hard drive plugged in.
So what should I do so that I will be able to go into windows 7 normally if the external hdd is unplugged? I would also like to be able to use ubuntu when I plug in the external hdd. I wouldn't mind having to go to the boot menu and choosing the external hard drive every time I wanted to use ubuntu.
The reason I partitioned the external hard drive was because it has a lot more space than my 250gb internal hdd, and I also wanted to leave space open to use as was intended, to back up stuff.
However, now that I think about it, I wouldn't mind partitioning the internal hdd and just leaving the external blank (which I should have done in the first place).
Because a lot of users are using laptops now, and many want externals hard drives for backups, is there a program in Ubuntu (cross-platform with Windows would be nice) that backs up files to an external hard drive when the external drive is plugged in or on a timely basis? All backup systems seem to have a timed system, but these systems have annoying pop ups if your backup location is non-existant (e.g. Deja Dup).
Use case 1: I plug in my external, the program recognizes that and starts a backup.
Use case 2: I leave my external in all day and every 6 hours, my laptop backs up my files to it.
I had this corrupted external hdd and so I formatted the main partition on it on windows but messed up in the formatting and ended up having to format the entire thing. I got some weird message about it not being initialized (no not mounted) so I was in compmgmt.msc in windows and right clicked it in device manager and it asked for master boot or GUID I selected the latter and formatted. Worked fine and all for a bit but now it doesn't show up as a drive. I noticed when using compmgmt.msc it showed up that it had installed driver software and was being recognized but in the partition editing area there was nothing on this drive, reinstalling driver software doesn't seem to help. Also GParted wont load up when I have it plugged in and Disk Utility doesn't show it. I am requesting help to fix this problem within Ubuntu 10.10 somehow so I can use it properly.
View 9 Replies View RelatedWell, the title pretty much sums it up. Whenever i plug in my external speakers, my laptop speakers continue to put out sound, which is good until i turn up the volume and hear rattling.
I am running ubuntu 9.04 64-bit 2.6.28-13 on an MSi GX620.
So I just got a new 1gig HDD and added it to my ubuntu server but if the HDD is plugged in when the computer is off, it will not boot. But if I turn it on and then plug it in, everything is fine.
I dont know whats happening when it tries too, there is no monitor. What logs should I check and what should I look for?
After I select to boot Ubuntu (I dual boot Vista Ultimate 64.), it just sits at a black screen with the blinking dash.Cannot enter anything and it will just sit there. But if I plug in my Flash Drive it will boot into Ubuntu either before starting the computer or while Im stuck in the black screen.Plugging in the drive while I am in the black screen will make it boot right up. The drive will light up and a couple lines that quickly say something will show up on the screen and then it boots.This Flash Drive contains Ubuntu and is what I used to Install Ubuntu.
View 9 Replies View Relatedi got a external hard drive for christmas and i installed ubuntu on it. then i couldent boot in to anything if the USB wasent pluged in because of GRUB so i removed GRUB and now i cant see my external USB drive in windows to formate it
Computer:
Toshiba
Windows Vista
External Hard Drive: HP Simple Save
I have a system I use as a file server running Ubuntu 10.04. I don't have a screen hooked up to this system. When this system reboots, if there is no screen, X wont start on it. This then prevents me from using VNC to get to the desktop.If a monitor is plugged in at the time it boots, then everything works, and I can then remove the monitor. But moving this monitor between computers and crawling under desks is not enjoyable.How can I fix this so X starts on boot even when no monitor is plugged in?The error I get in /var/log/Xorg.log* looks like this:
grep -EnC2 "EE|WW|fatal|error" /var/log/Xorg.0.log
...
331- (II) Primary Device is: PCI 01@00:00:0
[code]...
I want t understand why my 3G modem work only when it's plugged when my computer boot. If I forget to plug it , I need to restart my machine to get it working. I'm using ubuntu 10.04 when I plug the modem during the boot I get the product id changed from 1446 to 141b and dmesg |grep tty show me that the modem attached to ttyusb0 and ttyusb1 when I plug it after the startup I get also the product id changed from 1446 to 141b but dmesg |grep tty show me nothing.
View 9 Replies View RelatedI installed Ubuntu on to a usb hard drive now without that hard drive plugged in i cant get to my windows(it goes to grub recovery). With it plugged in it lets me pick witch OS to use. How do I get it to just boot right to windows when its not plugged in?
View 1 Replies View RelatedI have an old computer (Pentium 4) without a monitor. To make the most of it I installed Ubuntu server on it and have been using it for almost a year. A couple of months ago I don't really recall what I did but since then it doesn't start-up unless a monitor was plugged in.
I've tried pinging it but it doesn't respond when no monitor is plugged in. meaning it's not even booting correctly.
I'd like to know what the problem is and how to fix it. And I'd really appreciate any help in diagnosing the problem. I just don't know where to start.
I installed Ubuntu on external USB hard drive and while booting I did got option to log into windows XP, Ubuntu. Both operating systems ran fine. i.e. GRUB had overwritten MBR and I was able to dual boot. Main issue: I have installed Ubuntu in external hard-drive so that I can use Linux whenever I want other people who are using same computer can operate on WindowsXP. Sometimes my external hard drive gives problem if there is loose connection and so that oper people using computer do not face any problem I want to disconnect external USB HD whenever I am not using Linux. GRUB menu was pointing to external hardrive so disconnecting it meant my system wont boot!!I rewrote MBR using WindowsXP CD recovery mode. Now I am unable to boot from external USB hard disk( I thought I would be able to if I choose USB hard drive in BIOS option but it did not work it logged into WindowsXP by default).Is there any way I can change WindowsXP boot.ini file so that it also shows Ubuntu in external hard disk? Or is there any way.(I do not want GRUB way as then I would have to keep my external drive connected to log into windows - which I do not want).
View 1 Replies View RelatedI was building LFS on a pendrive this morning when it crashed in the middle of making gcc. I rebooted without my pendrive and I never got into the desktop. Instead, I get a visually pleasing terminal telling me that it couldn't find and that the only way to reboot would be to press CTRL+D. I'm then given a command line and that's that.
Rebooting with the key inside works perfectly.
I reformatted my key and now there's nothing on it. I feel like somewhere somehow I added an entry to the boot process of my system and now I have to remove it. Never dealt with something like this before
Fstab:
/dev/disk/by-id/ata-WDC_WD2500AAJS-60Z0A0_WD-WCAV2M336077-part1 swap swap defaults 0 0
/dev/disk/by-id/ata-WDC_WD2500AAJS-60Z0A0_WD-WCAV2M336077-part2 ext4 acl,user_xattr 1 1
[Code]....
The LaCie entry at the bottom there is my pendrive.
I am trying to build a media pc, and successfully so till this one little/big problem. I want to be able to turn on my tv, and pc, and have the pc display onto the TV. Ports used are HDMI(pc)->HDMI(HDTV)
But for some reason Ubuntu will not fully load with just the TV plugged in (all i get is a black screen, not even a "no signal" message).Once a LCD monitor is plugged into the VGA port. Then I see a glossy white Ubuntu symbol on the LCD monitor. Then the Ubuntu loading screen appears on both the LCD monitor AND the TV. in mirror mode. And I can see the desktop on both monitor AND TV.
I am using an ATI RAEDON HD 4200 chipset that is on the mobo. I have downloaded the proprietary drivers and installed them. A few things I have tried are the instructions on this page, finding my modeline using a modeline calculator and also going off of a suggestion from a thread on this website, stripping down my xorg file so that the Xserver would autodetect it. Which i think I did wrong because after that, it wouldn't display on TV at all.
So I think it's a problem with the resolution not changing back. But I don't see any menu, like the HP Logo, on my monitor at all. Thought It might be the blue cable, changed it, nothing. Plugged it back into TV and it works fine.
View 2 Replies View RelatedI have connected (sata cable I mean) the drive where I have got my Ubuntu installation to another pc with windows 7 64 bits (but I think that 32 and 64 doesn't make difference). Windows 7 doesn't boot. So I thought it may be some kind of issue with the hard drive itself (but the drive is healthy), anyway I have plugged one drive from one NAS (you know, NAS drives are linux partitioned and formatted).Same result: windows 7 doesn't boot.
Windows 7 boot sequence hangs and at the next boot prompts
"Repair windows installation"
"Boot windows normally"
(and obviously none of the options works)
Looks really like that Windows 7 doesn't boot if any linux partitioned and formatted drive is present.
I have some problem, the gparted 'searches' for ever on one disk only, even after 20-30 mins it is not finished and it has to be stopped manually.
Tried the same with debian, which has gparted 0.38, and the all works fine.
This used to work by default in previous versions of FF.
imdb $movie
wiki $some_topic
now they don't.
My personal favorite was
man $page
Open about:config and search for keyword.URL - it should be blank. Double-click to edit and enter
Code:
[URL] This will restore the previous Firefox keyword search behavior. No restart necessary.
I have a thinkpad e440 with Debian Jessie installed. I use GNOME and thus systemd. Recently the laptop's battery stopped charging when the AC is plugged in. This could be several things, maybe I need to get a new battery (the battery is only a year old). However I need a computer for work, so I tried unplugging the battery and turning on the computer with AC plugged in.
The computer turns on, the grub menu appears, but after I choose the option to boot Debian grub shows the loading ramdisk (or is it the kernel or something like that? The two lines that grub shows after selecting Debian) verbose and then shuts off. When I plug the battery back in, grub is able to boot Debian. As my battery is running out I am not sure whether I will be able to boot when the battery life is zero. Is systemd just looking to make sure the battery is plugged in and then fails when it is not? I suppose I'll find out soon as to whether I can boot without battery life, but the battery plugged in.
With 0% battery I am able to boot into Debian as long as both the AC and the battery are plugged in. Battery still won't charge, but at least I can use my computer.
If I boot CentOS (5, up to date) without my USB headphones are plugged in, all sound output goes to the sound card. But if I have the headphones plugged in when I boot, all output goes to them, and the sound card does not seem to be recognised at all.
Is there any way I can force the sound card to be recognised, and chosen as the default device, when booting with the headphones plugged in? If I have booted with the headphones plugged in, and then I unplug them, go into System|Preferences|Sound, and press the Test button with sound playback set to autodetect, I get a dialog with the message: audiotestsrc wave=sine freq=512 ! audioconvert ! audioresample ! gconfaudiosink: Could not open audio device for playback.
Then I started System|Administration|Soundcard detection, and it detected both Intel and Radeon sound cards, but its test button did not produce any sound for either. I moved the Intel device to the top of the list in the Settings tab, and then ran "Reload audio drivers" in the System tab. I got an error message saying I needed to reboot, but I didn't. At this point, the test buttons in the Sound test tab, and in System|Preferences|Sound started working OK. Do I have to go through this rigmarole every time I boot with the headphones plugged in?
Linux kernel 2.6, Slackware 12.0
How do I set case insensibility in searches running vim? I thought I could find this in the manual or the in browsing help within the program itself, but it was not long before I realized I was mistaken.
I am looking for the quickest way to do multiple searches for different files.Here is the scenario: I want to search for various icons one by one in a script. Preference is for the gnome icon theme.
The echo piped into grep part seems to take a long time. Is there a quicker way of doing this?I do not want to use slocate, sqlite or the like since that will require admin privileges to update the database and/or extra dependencies.
For about the past month I have been having a very frustrating problem When I boot the system with the ethernet cable attached it acts as if the cable is unplugged even though the connection light is litWhen I boot the system with the ethernet cable disconnected and wait until it boots all the way to gnome and then plug in the cable everything works fine
View 1 Replies View RelatedI deleted the search engines in chromium and made scroogle my default search engine. (im a huge privacy nut) But with this random daily build of chromium, whenever I close it, it deletes scroogle from my default searches.
View 3 Replies View RelatedI'm trying to write a script that searches my files and lists them by date. Can someone point me in the right direction? I've been looking through the books that i have but i'm just not finding the right commands to search dates.
View 7 Replies View Related