I have already tried reloading the drivers, restarting the interface (which is missing) and every other solution I found on this forum (well... not exactly all of them but many of them) uname -a gives Linux hostname 2.6.35-27-generic #48-Ubuntu SMP Tue Feb 22 20:25:46 UTC 2011 x86_64 GNU/Linux
[Code]....
I'm having trouble getting my Ubuntu 10.04 machine (Sony Vaio VGN-SR490) to connect to the Internet by way of an Ethernet cable connected directly to my router.
I'm able to connect to the Internet using this same cable using a Windows machine, so there's something wrong with the way Linux is configured.
How do I got about figuring out what the problem is and solving it?
Here are my network settings on Linux:
$ ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
[Code].....
It looks like the network adapters list is empty. I will now install both Windows XP and Ubuntu Linux dual-boot. I'm still not able to access the internet, even through Windows. I'm wonder if this could be a hardware problem with the computer or a problem with the router itself. Other computers can connect to this same router, and work fine. (That's how I'm posting this after all!)
I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedIf I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
I'm having the same Harker2010 's problem.Running 10.04 LTS on a Dell latitude D-820, and switching between lan and wifi worked OK until last upgrade.Harker2010's screenshots are also valid for my problem. I've tried everything I see on this post but the problem still there.
View 1 Replies View RelatedI have two network interfaces on my computer but only one of them is connected to an Ethernet cable. Until now on every Fedora release, the activated primary interface has been named as eth0 and everything has always worked well without any problem. Recently I switched to Fedora Core 12 and surprisingly I observed that for the first time, my primary interface has been considered by the system to be eth1 instead of eth0. I tried to replace the content of ifcfg-eth0 by ifcfg-eth1, yet system gave me an error that there was MAC address mismatching. I conserved their MAC addresses in their files and just replaced other connection parameters ( such as IP ADDR, NETWORK, NETMASK, etc.) but it did't work. When I do "server network restart", the command blocks.
As I try to install oracle on this system, regarding the fact that oracle requires static network configuration on the primary network interface, I don't know how to proceed in order to set eth0 as my primary interface (or rather set the current eth1 to eth0 because it is actually eth1 that refers to my activated primary network card).Just one more time, I would like to remark, that with previous versions of the Fedora Core, on the same computer (with the very same two network cards) I never had problem and I had installed oracle on the system with success, having the statically configured eth0 correctly detected by the system.
I found multiple sites explaining how to add IPs to a network interface as virtual interface like eth0:0. However I can add IPs to an interface as well using the ip command: ip a a 192.168.2.2/24 dev eth0 What I want to know is how I can make this persistent on rhel/centos.
View 2 Replies View RelatedI'm running fc10 x64 - latest updates. First I could never get wake on lan to work - spent days working on that one. Now, when I restart after a hibernate my eth0 is not re-enabled or recognized anymore. About to give up on Fedora.
I've tried service network restart.
I've tried unplugging cable and plugging back in.
I've tried init.d/networkmanager restart.
Only reboot works.
I've spent so much time trying to configure Fedore Core 10 for a Dynamips server and it's just not ready on some of the essential things like this hibernate problem and also wake on lan.
I'm trying to setup my interfaces along side GNS3 for study purposes, and came across a ..... vid saying to try this (my current config)
[Code]....
I'm praying for some crappy syntax error, also in Network Connections... its now blank, the original auto eth0 setup is missing
I just setup a SuSE 11.3/64 server and I am trying to setup pptpd for a vpn. I noticed thatg the ppp0 (or any pppx) interface is non-exoisting and I think that that is the problem why my gre packages are not being sent by pptpd (as I have checked all other options). I have tcp port 1723, and protocol port 47 (gre) open on the firewall (SuSEfirewall2). I have traced the responses using tcpdump and only when the server sends gre to the remote client, the client never receives it (the 1723 connection is established). I checked the old server (SuSE 10.2) that worked the vpn fine, and the only thing missing on 11.3 is ppp0. All other hardware (routers, etc.) are the same. I suspect that pptpd tries to use ppp0 and the interface is non-existing. I can remotely ssh to the server, dns works, samba works, everything else works. Is it something I am missing? How do I create if ppp0 and link it to eth3, the internet gateway?
As always, a windoze tech crashed the old server and I had to setup the new one in a hurry, just before going on vacation, and people want this done by yesterday? They paid $$$$ to the windoze tech (who said Linux is obsolete) even after he almost brought the company down!
The following are the output of command "ifconfig -a":
[Code]....
The interface "eth0", which is down, was not displayed, but loopback interface has been displayed. So, how can I make my application display all interfaces, including the interfaces which are down, but excluding the loopback interface?
I booted an OS from a live CD. The OS boots successfully but eth0 fails to start. I checked lspci, it outputs these Ethernet card details:
(Broadcom Netextreme II BCM5716 GBabyte ethernet)
ifconfig -a returns only the loopback interfaces lo and sit0. The output of dmesg | grep -I 'eth' is:
"Netfront : initializing network ethernet driver"
When I run service network restart I get:
"Obtaining IP for lo [FAILED]
WARNING: Deprecated config gile /etc/modprobe.conf , all config files belong into /etc/modprobe.d/
Device eth0 does not seem to be present, delaying initialization [FAILED]"
The output of MII-tool -v is:
No MII interface found.
I was also able to find the kernel module bnx2.ko. I did insmod and lsmod lists it.
I'm using CENTOS 5.5 and I want to connect to internet using 2 pppoe accounts same ISP and i have a sigle NIC eth0.I used adsl-setup to create pppoe connections, 1 is ppp0 and second is ppp1. When i use /sbin/ifup ppp0 it works, i can use the internet, but when i try to use /sbin/ifup ppp1 while ppp0 is connected, nothing happens, i did ifconfig and there is only ppp0 showing.I'm a BIG NEWBIE of linux, i need to know step by step how to make this work, i heard something about a virtual network... but nothing clear.
View 5 Replies View RelatedI am trying to connect my fresh new Ubuntu 10.10 to my router. However I am having a bit of difficulty. This is what I have done so far:
Code:
lspci
My devise is a Broadcom Corporation BCM4311 802.11b/g WLAN (rev 02). Then:
Code:
sudo ifconfig eth0 up
sudo iwlist eth0 scan
I get eth0 Interface doesn't support scanning.
I have followed th given site for HA configuration in my virtualbox but heartbeat is not assigning virtual IP for interface eth0 [URL]...
View 1 Replies View RelatedI'm using CENTOS 5.5 and I want to connect to internet using 2 pppoe accounts same ISP and i have a sigle NIC eth0.I used adsl-setup to create pppoe connections, 1 is ppp0 and second is ppp1. When i use /sbin/ifup ppp0 it works, i can use the internet, but when i try to use /sbin/ifup ppp1 while ppp0 is connected, nothing happens, i did ifconfig and there is only ppp0 showing.I'm a BIG NEWBIE of linux, i need to know step by step how to make this work, i heard something about a virtual network... but nothing clear.
View 7 Replies View RelatedI used the network manager to configure my eth0 interface.It is working fine. I have found the nameserver entries in /etc/resolv.conf files. But the /etc/network/interfaces file does not carry the ip, netmask, gateway,network and broadcast entries. It only has a entry for the lo interface. where are the settings for eth0 as done by the network manager, stored in case of ubuntu?
View 7 Replies View RelatedI am in need of finding out the physical interface corresponds to eth0,eth1,eth2., As similar like the lscfg command which is available in the AIX operating system. The output given below got it from AIX OS.
$ lscfg -l ent*
ent2 U787B.001.DNWFFC6-P1-T9 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent3 U787B.001.DNWFFC6-P1-T10 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent0 U787B.001.DNWFFC6-P1-C4-T1 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 U787B.001.DNWFFC6-P1-C4-T2 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
Is there any utility/commands available to find out the physical interface ?
I have set 'ONBOOT=no' in interface script '/etc/sysconfig/network-scripts/ifcfg-eth0:2' but my interface bring up at boot time, what is the problem , I have checked it 3 or 4 diff os/machine but the same issue. Can anyone please help me to disable virtual IP's at boot time that network script make it up every boot time.
View 4 Replies View Related5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
I have 2 network cards eth0 and eth1, for eth0 i set a manual MACADDR in network scripts. Ok so every time i boot, if the cable is plugged in, my eth0 fails to mount or i don't know.. i get this after bood when i type ifoncifg eth0 (eth0: error fetching interface information:Device not found). So i have to unplug the cable when i boot, then plug it in and do a service network restart.
View 5 Replies View Relatedim trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
Last weekend I upgraded my Opensuse 11.1 machine (pretty clean) to 11.3. After the upgrade, the NVidia graphics no longer worked, but more importantly, eth0 was not bound to my Intel 82566DC gigabit ethernet controller. I fooled around in yast network devices long enough to know that everything there is configured correctly. The Yast message at the bottom of the Network Settings screen says:
"Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details."dmesg output shows nothing related to networking. The boot screen shows:
Setting up (localfs) network interfaces:
lo ...
Waiting for mandatory devices: eth0 __NCS__
29 28 27 ... 1 0 ... failed
eth0 no interface found ... failed
[code].....
Any ideas here? I've googled till my fingers were tired and all I've found are references from folks with real hardware issues. This machine worked fine for me under 11.1. Now I can't get 11.3 to bind the nic.
I just had an ATT Uverse RG installed. However my Smoothwall router that previously worked fine with the ADSL SpeedStream is no longer accepting an address assignment DHCP ip address from this new gateway. (3800HGV-B)Any thoughts ideas or experience working with this hardware? ATT only supports Windows and Mac
View 2 Replies View RelatedI have a ppp0 entry with post-up options like this
mapping ppp0
map none photon-plus motorola
map timeout: 12
[code]...
I just installed Fedora 13 on a new Dell XPS desktop and some of the networking files are not created/missing. The computer has Broadcom Gigabit wired card and Asus PCE-N13 wireless card. When I type lspci, I see that Network conroller: RaLink RT2860 and Ethernet controller: Broadcom BCM57780 Gigabit Ethernet. So, somehow they are being detected by the OS, but I am not sure if the drivers are installed or why some of the network files are missng.
View 1 Replies View RelatedI try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.
1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them
[code]....