I'm on Ubuntu 10.04 and I'm having problems with internet speeds on wifi. I have tried the two available networks on my university campus and both of them are very slow with 10.04. I'm not having problems with Windows 7 running on these networks. Although, the wired network works perfectly fine, with normal speeds. I've looked around for help but I could not find anything specific to this problem.
View 2 Replies
I'm finding that the internet speed in Ubuntu 10.04 is over twice as slow as the speeds that I am getting in Windows 7.I've tried disabling IPv6 through Grub and Firefox but it didn't really help much.. anything else I can try?Connecting through wireless at 54 Mbps.
View 2 Replies View RelatedI've been using Ubuntu for a while (though I would not consider myself an "expert") and have just gone back to school. I live on campus and connect to the network through an ethernet cord. On Windows, the download speed is 1 Mb/s by default, but if you go through and configure the network card (turning off the auto-negotiation and setting the speed to 10, duplex full) the download speed will increase to 10 Mb/s, a considerable difference. So, I tried to do this in Ubuntu by opening the terminal and typing the following:
sudo ethtool -s eth0 autoneg off speed 10 duplex full and all of a sudden, my computer isn't connecting to the internet. When I type: sudo ethtool -s eth0 autoneg on it suddenly starts working again.
I have recently switched to Ubuntu 11.04 64bit from Windows 7. Since installing 11.07 I have experienced random disconnects, slow speeds and just overall poor performance from my ethernet card. Looking into the issue further I noticed that the driver installed for my NIC is "driver=r8169", but the actual NIC card is "product: RTL8111/8168B PCI Express Gigabit Ethernet controller" which I think pretty much says I should be running the 8168 driver.
When I run lsmod I only see "r8169 " installed. How do I go about getting and installing the r8168 driver? I am pretty sure I just need to install this driver and then blacklist the r8169 in blacklist.conf. Any clarification would be great.
I'm using a Netgear WN11v2 wireless USB card, which I've read some people can't even get working with the default Ubuntu wireless driver. It works for me, but it disconnects fairly often, and download speeds are extremely slow, like 12-15 kB/s. I have broadband, and am running Ubuntu 11.04.
View 3 Replies View RelatedI am currently staying on a university campus in Taiwan. Internet on Ubuntu Lucid 64bit here is often painfully slow, except for connections to Taiwanese websites. I dual boot with Windows 7, and there is no problem there. For instance, I downloaded the same piece of software (Spideroak) on both Win and Ubuntu, with Ubuntu I had to try repeatedly as the download would not complete, and in the end it took several hours to download. On W7, it took 10 minutes. What is Windows and Ubuntu doing differently?
I tried disabling ipv6 for this session by running sudo sysctl -w net.ipv6.conf.all.disable_ipv6=1, as a number of posts mention improving connection speed that way, but no effect.
I know that websites from Taiwan are working well, because I am getting my Ubuntu updates from a Taiwanese mirror: updates are fast, except for packages in the 'partner' repos (presumably not loaded from the mirror) which take hours to load, if at all. I don't want to depend on Windows for large downloads... (I don't want to depend on Windows for anything).
I've just managed to access my windows share from Ubuntu but am now getting write speeds (to xp share) of only 9MB/s over my wired network, anyone have any ideas as to why this may be? I've googled but can find no specific answer.
My NIC is:
Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10)
(from lspci) on a Dell studio 1737)
My wireless network is giving me a fit. Slow transfer speeds and then I lose connection and have to reboot.
greg@greg-computer:~$ /sbin/ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:92 errors:0 dropped:0 overruns:0 frame:0
TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10214 (10.2 KB) TX bytes:10214 (10.2 KB)
wlan0 Link encap:Ethernet HWaddr 00:16:b6:5a:9c:a5
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::216:b6ff:fe5a:9ca5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13085 errors:0 dropped:0 overruns:0 frame:0
TX packets:9600 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:15268450 (15.2 MB) TX bytes:2704035 (2.7 MB)
wmaster0 Link encap:UNSPEC HWaddr 00-16-B6-5A-9C-A5-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets: 0 errors:0 dropped:0 overruns:0 frame:0
TX packets: 0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes: 0 (0.0 B) TX bytes:0 (0.0 B)
greg@greg-computer:~$ netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 wlan0
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0
greg@greg-computer:~$ cat /etc/resolv.conf
# Generated by NetworkManager
nameserver 192.168.1.1
greg@greg-computer:~$
Trying to watch movies between my systems and I'm getting upload speeds of 6.5 kb/s from my system to the one connected to the tv. I'm running Ubuntu on both machines, tried with VLC and XBMC. Both are running wirelessly but I know that this issue is new, I used to get at least a meg a second on LAN.
View 9 Replies View RelatedI'm having a variety of problems getting a new PC working properly, getting a reliable wifi connection is one of them. Earlier today I upgraded to 10.10 using my wife's account and download speeds were frequently at a reasonable 800kbps at times. This evening my son complains about the slow speed and a test shows 133kbps download with 616kbps upload. My own PC connected by wire to the router works OK.
A couple of days ago this problem seemed resolved when I installed Wicd but didn't configure it. I thought Network-Manager would have been removed but was still present. However, a downloads test showed 6Mbps. After today's upgrade slow downloads have returned.
I'm currently using this PC with a wifi link to the router and am connected to the Forum. If I hover the mouse pointer over the N-M toolbar symbol a window opens saying-
Wireless network connection 'Auto MYESSID'active:MYESSID(67%) If I right mouse click on the N-M symbol and select Edit connection... the wireless window reports that I was last connected 3 days ago. My own PC's wired connection window says against Auto eth0 that I've never used this. Both these are untrue. I wondered if having a hidden ESSID doesn't help? I'm left thinking that the rt2500 based wifi card needs replacing. We're some distance from other houses.
Whenever I transfer a movie into my 16GB USB flash disk, my whole system becomes windows-like and unusable!
When i drag the file(s) into the USB disk folder, it starts out fine and pretty darn fast (25mb/sec) then slowly decreases until it's unbearably slow (3m/sec) and as a side effect my whole system starts deteriorating. I basically have to wait for the file to finish transferring before i can use my desktop again!
This has been happening with every version since Karmic (all 64bit)- I put up with it because I don't use the USB stick that much.. but lately it's been my go to source for transfering large files to/from work.
get WIFI working on my Dell D600 with Ubuntu 11.04 freshly installed. I some limited sucched following the this post t=1621331 this got the card working but it was very very slow over 70% packet loss to the WIFIrouter. 1. Machine details Dell Latitude D6002 Wireless Broadband and Chip setlspci -nn | grep Broadcom - 02:03.0 Network controller [0280]: Broadcom Corporation BCM4309 802.11a/b/g [14e4:4324] (rev 02)3. Check interfaces
eth0 Link encap:Ethernet HWaddr 00:0b:db:e0:1c:5b
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[code]...
Last week I attempted to get "up to speed" with my Comcast cable connection... Ubuntu 9.10, Dell Vostro 400 desktop, Firefox 3.6.13... Comcast says I should have 12 Mbps connection... if I get 1.0 Mbps, I'm doing good... they just tested everything, and said everything is fine on their end. They use [URL] and connects to a server in Chicago, 60 miles away. That gets fantastic speeds, and it's a durn shame the internet doesn't store all its files there!! I use [URL] for my tests, and it uses a server in Dallas TX.
I go to my girlfriends house, and her AT&T DSL line has d/l speeds of 4.5 Mbps or better!!! She's running XP Pro on a Dell machine. So, started digging on the web and thru the forums, and found this:
[URL]
But, like ALL too many things, it's dated... it's from 2008... I've set my settings to what is there, and disabled ipv6 in Firefox. Hey, now, I'm sometimes up to 1.4 Mbps!! Also found this, but no date...
[URL]
Reading forums, I see that folks have said there is a network connection problem with 9.10... and then I see that others are saying the same thing about 10.04 and 10.10!! I have 10.10 on my laptop and had to fight to get its Atheos card to be recognized. Running some tests [URL] gives me weird results: Download 2.64 Mbps, Upload 4.12 Mbps. NOT what it should be. Similar results from testmy.net.
Dunno exactly what info is needed... Speedguide.net gives me results below, but I've tried changing numbers (says my RWIN is low) and nothing changes:
--------------------------------
TCP options string = 020405b40402080adf1dca100000000001030306
MTU = 1500
MTU is fully optimized for broadband.
[code]....
So, today, find, once again, that I'm d'ling in the range of 90/KB/s (719 Kbps)... disgustingly slow. I go on my HP laptop and run the test, and it says 1.6 Mbps. So, desktop directly connected to router is not even 1 Mbps, and wireless connection is faster? Neither of which is close to what I should be getting...
Is there a way by which i can improve my Internet speed. I have a 100Mbps connection but the download speed is only 100kbps. I know that my ISP has limited by connection speed, but i am curious to try as to how i can get the maximum speed.
View 5 Replies View RelatedMy Netbook is ASUS EeePc HA900, I already use Ubuntu 10.04 is ok, nothing problems, then I upgrade to Ubuntu 10.10, it is still Ok. But when I upgrade to ubuntu 11.04, it have problems with Wifi, when I connect Internet via Wifi, just input the Password, it make my computer slow to halt, and have to turn the power off to shutdown the computer.
View 1 Replies View RelatedI have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?
View 2 Replies View RelatedMy wireless seems to be fast for a good 30secs then bang takes good while to load the next page almost as if it's disconnecting and then reconnecting/scanning reconnecting. Why cant it stay connected. I have WAP PSK security here is my network setting please let me know if I should change any of them:(side not is there a way to fix this problem occuring so frequently it says on the wiki that it should only occur once in a whilce https:[url].....
View 2 Replies View RelatedI am using Ubuntu 10.04 and my internet works fine except for my download speeds. In Windows, downloading the same file, it downloads at around 200kb/s but in Ubuntu, it hovers around 20kb/s and never tops 50kb/s. Any idea how I can fix this because I really don't want to go back to Windows but I may have to.
View 2 Replies View RelatedHey guys, I got a new laptop, so I installed ubuntu 11 on my old laptop. And I have noticed the download speeds have been extremely slow.I have only been getting speeds around 20-60 kbs/sec before I installed ubuntu when it was running windows 7, I was getting around 100-300 kbs/sec. I know its not my internet, because my new laptop runnings windows 7 gets about 250-300.Any suggestions? Its not just in chrome or firefox, its especially slow when downloading packages.
View 7 Replies View RelatedWhenever a client tries to download a file from my server via ftp, SAMBA, Teamspeak 3 File Transfer, etc., they report very slow download speeds, around 3-6 kb/s. If I try a ftp file transfer locally, the upload speeds are normal, but I still experience slow download speeds.
My server is connected to a router, which connects to the internet. All other machines connected to that router can upload and download files at normal speeds. It seems to be a server problem, I just don't know where to start.
I have read many threads but cannot find a solution on this code...
Now no matter how i transfer if its from HDD to HDD or to SSD i never get more then 18-20MB/sec, i just tried booting to my live CD and was able to transfer with 24-25MB/sec
This is really slow, since the worst (2.0TB) can do a minimum of 30 READ
Anybody got any ideas, this seems to be something that has plagued ubuntu for years, and no i don't want to try other distros, i tried almost all of them a year ago and finally went with ubuntu
I'm at the end of my rope here. And the most frustrating part is, I've found many posts all over the web from others who have had similar problems, but they ALL seem to be older distros and those solutions don't work for me. "Find Similar Threads" only yields one thread, and I don't have the file mentioned in the answer (the original poster didn't either).
Computer: AMD 64 Quad core, USB 2.0 on front bus, dual booting Vista and Ubuntu 10.10
Device: New Sansa Clip+ 8GB mp3 player
Problem: When I transfer files to my mp3 player in Ubuntu, I max out at about 150 KiBbps. It's painfully slow - it takes me half an hour to transfer 300 MB worth of albums. I had similar problems with an older player that may have been usb 1.1, but this one is brand new. And when I switched to Vista (first time in months, thankfully), I was able to transfer the same files at upwards of 3 MBps. I know that flash devices often can't write anywhere near the max speed of USB 2.0, but obviously it can do a whole lot better then 150 KiBps!So, same hardware, same files, different OS - the problem must be with my Ubuntu config.
I when I burn a dvdrw with K3B, it remains at 1x speed even tough I chose the maximum speed in the dialog(don't know whether this is also the case with dvd-r or cdr since i don't have any with me at the moment). So, I guess there is something wrong. I read that it could have something to do with DMA, Or could it be something else?
View 1 Replies View RelatedI tried using my USB to transfer a 500MB file, the speed came up as 1-130 kb/s. That is pathetic. I should be getting more 25MB/s.
View 14 Replies View RelatedIn my desktop I recently installed one of these network cards. Web pages load pretty quickly, but the signal is only 2 out of 5 bars. On my notebook, I get 4/5 bars from the same location away from my wireless router. I have a 25/25 Verizon FiOS plan and can usually obtain around 30Mbps through Speedtest on my wired machines and notebook. But for some reason, my desktop barely goes over 4Mbps.
View 2 Replies View Relatedhave the latest Vbox installed on CentOS 5.4, i have a XP home VM & Server 2003 VM set up. Im using the T1000 Emulated network driver and only getting 100-150mbps throughput when checked with QCheck. I tried the virtio-net (paravirtualized) drivers and only getting 50-90mbps using it, which i found odd. Is there any way i can increase the througput to my VMs? I seen some people on forums talking about getting 300-350mbps, but im no where close to that. When i check throughput to the host (CentOS) i get at least 800 mbps.
View 2 Replies View RelatedI have a 4 drive RAID 5 array set up using mdadm. The system is stored on a seperate physical disk outside of the array. When reading from the array its fast but when writing to the array its extremely slow, down to 20MB/Sec compared to 125MB/Sec reading. It does a bit then pauses, then writes a bit more and then pauses again and so on.The test i did was to copy a 5GB file from the RAID to another spare non-raid disk on the system average speed 126MB/s. Copying it back on to the RAID (in another folder) the speed was 20MB/s.The other thing is very slow several KB/s write speed copying from eSATA drive to the RAID.
View 9 Replies View RelatedI set up software RAID 5 on three 7200rpm Seagate Barracudas (2x80GB, 1x40GB) with 40 GB partitions on the beginning of all three disks.Now, when I do benchmarks using the Disk Utility I get about 52 MB/s read speed on the array. This seems kinda slow considering the average read speed on each individual drive is about 48 MB/s. Also, boot up takes about 30 seconds, which is the same as when I had Ubuntu installed on just one of the 'cudas, without RAID. Now, I am I missing something? Shouldn't the read speed be more that twice as fast since it can read from all three disks?
View 1 Replies View RelatedI'm trying to back up my hard drive to a 2 TB WD external so that I can do a clean install of 10.10, however I'm getting tremendously slow write speeds. It hovers around 1.5 MB/s and steadily slows from there. It tells me it will take 150+ hours to transfer 400 GB of data.
I have a AMD quad core processor and 8 gigs of ddr3 ram... USB 2.0... I feel this should go much faster.
I've just installed the ubuntu 9.10. I have one problem with it. I have a home net in configuration: Windows XP on a cable, Ubuntu on a cable and Windows on wifi. When I'm surfing on the net on Ubuntu, Wifi isn't work how it should. It's very slow and I don't know what to do with it. Windows XP on a cable is OK, it works good. What happen and how can I repair it?
View 2 Replies View Related
