My laptop is Gateway M-6335 and I have problems with wireless drivers. I couldn't find any drivers for it. I searched in Software Centre and tried to google it but it didn't work. I have also problems with Bluetooth driver, but it's an other story. I'm using Ubuntu 10.10.
View 9 Replies
I have been trying to get my wireless interface work but i am unable to find a driver for the wireless interface.
View 1 Replies View RelatedI am completely new to linux in any flavour. I installed ubuntu 10.4.1 64-bit on my Gateway NV59 laptop as a dual boot with Windows 7. The installation went just fine. When it comes to networking, I can connect to my home network when wired directly, wireless is another matter. I can connect wireless in windows just fine, so the card is physically fine.
My set up is as follows:
Gateway NV59 laptop with Atheros AR928X PCI-E wireless adapter
Linksys WRT54G router using WPA2 Personal and a class C address scheme (192.168.x.x)
(If anyone thinks it would be necessary to post actual hardware specs of the laptop, I can, but don't think it really necessary). I have followed the Wifi Wireless Troubleshooting Guide found at [URL].
When connecting to my network wirelessly, I click the icon in the top right, and choose "Create New Wireless Network". When I input my settings (SSID - not broadcast, and security type and key - WPA), it then states I am connected under the "Wireless Networks" section found in that menu, and shows my network name with a strong signal and a computer/monitor icon. When I double-click the icon, it tells me I am connected and that the connection is active, yet the actual wireless icon on the top bar is grey, not white, and has a red exclamation mark on it. According to the steps in the troubleshooting guide, my wireless card is recognized and installed, with a driver of ath9k.
When I run lsmod, the driver is listed, therefore loaded, and ndiswrapper is NOT listed. I have verified that the driver is communicating with the kernel. When I scan for my router, it is listed under Cell 04, with the correct SSID and hardware address. There do not appear to be multiple drivers loaded, and my wifi is NOT disabled. When I check to see if I'm associated with a router, iwconfig shows my network ssid under wlan0, with the correct hardware address listed under Cell:, yet I cannot ping my router's internal ip address. At this point, I ran ifconfig, and for some reason, my wireless card has been given a class A address of 10.42.43.1.
When I try to assign an ip address via dhcp, DHCPDISCOVER runs for a number of intervals and then tells me "No DHCPOFFERS received", yet my router is using dhcp to assign ips with a pool of 50, more than enough ips for all the hardware in my network. When I run the command "sudo invoke-rc.d networking restart", I get the statement "Ignoring unknown interface wlan0=wlan0" - not sure what that means, but doesn't sound good to me, and retrying to accquire an ip address through dhcp still does not work. If I attempt to assign an ip address within my network range manually, I first run the command "sudo ifconfig wlan0 down", then just out of curiosity to see if the interface is really down.
I run ifconfig again, and wlan0 is no longer listed, but now there is eth0 (my regular ethernet interface) with no ip address. AND another interface is listed - eth0:avahi with the same hardware address as eth0, and an address of 169.254.4.42 - this seems to be the default address the OS will assign when it cannot get one via dhcp, but I have no idea why it has shown up as eth0::avahi... Anyway, after entering the command "sudo ifconfig ip addr 192.168.x.x netmask 255.255.255.0 broadcast 192.168.x.255 up" with the appropriate addresses, I receive the error "addr: Unknown host".
What I have NOT tried, are the following steps:
1. Change my router to an open signal (I would prefer not to do this, but will, if it is absolutely necessary for troubleshooting)
2. Try gtk wifi, or wifi radar
3. Try booting with kernel option pci=noacpi or acpi=off (not entirely sure how to do this just yet)
4. Try wpa supplicant (not sure what this is, just noted it was in the troubleshooting guide)
I'm having problems getting the wifi to work on my toshiba satellite pro l40 (psl4be). My laptop has a wifi card built in but linux cant seem to be able to find it. I tryed following these instructions and i got this output:
Code:
james@james-laptop:~$ lsusb
Bus 007 Device 001: ID 0000:0000
Bus 006 Device 002: ID 0bda:8197 Realtek Semiconductor Corp.
Bus 006 Device 001: ID 0000:0000
[Code]...
as you can see its telling me i have no wifi card, even though i am fully aware i do. ive tryed using ndiswrapper to install the windows drivers of the ethernet adaptor but my wifi still doesnt work, im guessing ethernet has nothing to do with wifi.I intend to convert from windows, however if i cant get the wifi to work i can only see linux at a major disadvantage as i use my wifi alot.
I switched my girlfriend laptop from windows 7 to Kubuntu 9.4, then upgraded to karmic koala. I was able to, through the hardware manager, install a software modem driver, and a firmware unwrapper driver for her broadcom 4.X series wireless adapter. Whenever I attempted to install the broadcom 4.1, 4.2. ect driver itself a package update would fail, but wireless functionality still worked nonetheless. My girlfriend has a TX1000 HP laptop, similar to this one:[URL]..Product number in the bios is GA648UA#ABA System Board ID is 30BF
The wireless drivers she needs are proprietary. This worked for a while, although seemingly at random her wireless would go out, and her analog sound driver for her Nvidia chipsets would too. Usually logging out of the KDE environment and back in fixed the issue. Now wireless is completely gone; using a hard ethernet core to the router still works. Even connected to the internet, the proprietary drivers that used to be available in the hardware manager aren't there anymore. Right before the driver disappeared, I updated the system with all the latest round of updates, and installed the base package and some plugins for VLC. I don't know how to role back packages to see if an update killed the wireless, I uninstalled the VLC software but that didn't help.
Wireless is checked enabled on my taskbar, and I have checked my bios and haven't found any setting to disable the wireless adapter. Anything networking related has been enabled. At this point I am rather frustrated with the stability of Kubuntu overall and would prefer a hard solution that will permanently fix the problem.
Ok I am a complete Noob when it comes to anything other than a windows based unit, so please be patient with me. I am able to connect to the Internet using a wired connection.
View 6 Replies View RelatedI am new in using Debian 5.0, my wireless doesn't work I make a search to know how to do it.
So I open "Terminal"
$ su (press enter)
I wrote the pwd
than when I wrote : # gedit/etc/apt/sources.list
I found this:
bash: gedit/etc/apt/sources.list: No such file or directory
I didn't know what to do, I proceed with: # apt-get install ipw3945 modules-$(uname-r) ipw3945d firmware-ip3945
bash: uname-r: command not found
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package ipw3945
I am recently trying to get a steady wireless connection running. I am currently using the default settings/driver Fedora 13 is stocked with. As my internet browsing is somewhat up and down in load times, I decided to check in a video game which is generally a good test for me. haha I am harshly spiking and cannot find the source of my problem so my guess is a driver issue.
lspci | grep Network:
Code:
Code:
It is is seemingly right, my Windows 7 harddrive works just fine, this is just one last of the few issues I'm having from fully formatting my winblows HD to use as Linux storage.
I cannot find any native AR5008 Linux Drivers for my card and it has been a frustrating day. I guess I'm not cut to be a network analyst just yet.
System specs:
ASUS P5Q SE/R
Intel Core 2 Quad Q9550
4GB DDR2 667
Gigabyte GTX465 1G
TP LINK TL-WN851N Wireless card
I am new in Linux and Ubuntu. I am using Acer Aspire 4740 laptop. How can i find related drivers for my laptop?
View 1 Replies View RelatedI have two computers. The first computer has windows xp in it and is a member of the local lan with ip address 192.168.11.21. The second is my laptop having ubuntu 8.10.Both these computers are connected to each other via the broadband router which assigns ips 192.168.1.3 to my laptop and 192.168.1.1 to my desktop. I am able to browse the lan of 192.168.11.x via the desktop and I want the same possible on my laptop whose only connection is through the router to the desktop. Is there any way I can do it?
View 1 Replies View RelatedI've installed Ubuntu Netbook 10.04 on my HP DV2000 laptop and now I want to get my wireless to work by installing the proprietary broadcom drivers (4311, I think). But my internet doesn't work yet obviously, so I need to download the drivers to my thumb drive on my desktop and install them on my non-networked laptop.My issue is that I don't know:a) Where to get the driversb) How to install them from a local drive
View 2 Replies View RelatedI can't see any wireless networks with 10.04 Netbook version. iwconfig gives me this:
lo no wireless extensions
eth0 no wireless extensions
wlan0 IEEE 802.11bg ESSID off/on
a wireless router (box) is went stuck, I found that when it is stuck it uses strange IP local address remote address 10.112.112.112, today is also went stuck but this time the gateway was 10.112.112.112. I had to switch off, switch on teh router to function properly. I am using DSL connection normally the gateway is likie that 78.8.... and my IP (dynamic) like 78.8.240..... Is there any default meaning of 10.112.112.112 in teh net connections?
View 14 Replies View RelatedI have a Gateway laptop (model MT6458 ). You'll have to bear with me, I'm very inexperienced with Linux in general and especially the command line. Previously, I was running 10.04 32bit. I wanted to give 64bit a try, so I just fresh installed 10.04 AMD64. I was able to get my wireless working in the 32 bit version as seen on this thread: [URL]. After installing the 64 bit version, I attempted following the same directions as before, but it doesn't seem to be working.Here's some of what the terminal is telling me:
Code:
jeremy@jeremy-MT6458:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
[code]....
I can't seem to find drivers for my wireless adapter, TL-WN722NC, so that it can work on Linux (Ubuntu). I have already emailed the company, TP-Link, and they said that it does not support Linux yet.Is there a way that I might be able to get drivers for it somewhere else?
View 5 Replies View RelatedI've just installed fedora 10 on my Dell Inspiron 1525, and I can't connect to my wireless net. I know how to manually enter the SSID (and have no clue what a BSSID is), MAC address, and I know it's infastructure (well, it's not ad-hoc, so it must be).
The problem is, my router uses a 64-bit encryption protocol, and there's no '64-bit' key option under Wireless Security's dropdown. Is there any way around this, aside from either changing the encryption protocol, or plugging it in manually (neither of which are options)?
I cant get openSuse to find my wifi adapter or it does not have the driver installed.
My wifi adapter is the Realtek RTL8191SE 902.11b/g/n
I found a linux driver on the internet, but it asked me to run make in the console and when I did so it said that it couldn't find make.
how to install make from openSuse without the internet (I'm using my windows partition).
I am not able to use internet using wireless lan. I am Not able to find the hardware and install the drivers .Please help me.I am Using red hat linux 5.4.
View 3 Replies View RelatedBought a Canon all-in-one (printer, copier, scanner) today, which prints beautifully on XP & connects to our WiFi without problem. Only downside, is it can't find a driver for Linux. Anyone out there using this printer under Linux, or any pointers to the right driver?
View 3 Replies View RelatedI recently reformatted and dual partitioned to both Windows 7 as well as ubuntu 10.10. Loading works fine and Windows 7 is 100% operational. I cannot seem to get my wireless network adapter to be read by Ubuntus 'Windows Wireless Drivers' gui. Here are the steps that I have done THUS far, to make sure that we are all on the right path. Before I go any further, my wireless network adapter is an old school WUSB11 Linksys Wireless Network Adapter (running version 2.6).
1) Downloaded and installed "ndiswrapper" from ubuntu's main website. I downloaded the common, utils and ndisgtk files and installed them accordingly.
2) I extracted these three files to the desktop of Ubuntu and accessed the terminal page.
3) From terminal I typed "cd Desktop" to change the directory to the desktop.
4) Next, I typed in "Sudo dpkg -i ndiswrapper-common_1.54-2ubuntu1_all.deb
Sudo dpkg -i ndiswrapper-utils-1.9_1.54-2ubuntu1_i386.deb
Sudo dpkg -i ndisgtk_0.8.5-1_i386.deb"
5) This installed Windows Wireless Drivers gui successfully and I can access it.
6) I have downloaded the driver files for the adapter from the cisco website and searched them for the required files needed.
7) After extracting the .INF file from the "Drivers" directory named "NETUSB.SYS" (I wasn't sure if the other associated files within the same folder needed to be present together with NETUSB so I moved everything to the desktop) I typed in "sudo ndiswrapper -i NETUSB.inf". After accessing the Windows Wireless Drivers gui I have noticed that the 'netusb' driver is present yet under it, the system states "Hardware present: No". This leads me to believe that maybe I installed incorrectly or my "fireware?" is not present? I was reading through the installation guide posted on the ubuntu website that in addition to the .INF file we also need the BIN file(s)? and SYS file(s)?.. The folder with the drivers for my adapter contains a BIN file but it is not within the "Drivers" section of the folder.
9) Upon mousing over the network Icon naturally my hardware is still not present.
10) From what I gather after the system finds the hardware I am to write into the terminal
[Code]....
I am wanting a computer with an external dialup modem (ppp0 modem through a com port /dev/ttys1) to act as a gateway to the internet, forwarding internet traffic through ethernet (eth0 is set to static 192.168.2.2) to a router (the router is 192.168.2.1) where it will be broadcast to other wireless computers like my laptop (192.168.2.3). I've had this setup until recently when the gateway computer (the one with the modem) died. Now I'm replacing that machine with another box and an install of Ubuntu 10.10 but so far things aren't working for me.
Success so far:I have dialup access working on the new box. Took me a while to work out the configuration for getting dialup working, though the IP address is Dynamic (or it won't stay connected), "Check carrier line" is off, and "Ignore Terminal Strings (stupid mode)" is on in order to successfully connect and stay connected to my ISP. I also had to make my normal (non-root) user "lancer" a member of the "pid" group (the reboot) in order to use gnome-ppp as non-root. The laptop (192.168.2.3) is successfully connecting to the router (192.168.2.1) as I can see the router configuration page when I type http://192.168.2.1 into the laptop's web browser. This setup is unchanged from how I had it before when this was previously working and I don't want to change how the router itself is set up. What I want is to know what to fix in the new box in order to get it connected to the router (through ethernet) and bridging the internet through.
My problem is that whenever I plug in the eth0 from the gateway (192.168.2.2) to the router (192.168.2.1), Ubuntu's automatic plug-me-in network detection kicks in and I find my dialup no longer working through some kind of IP conflict (at least that's what I think it is). Maybe I don't have the "gateway" correctly assigned? (in the gateway computer for the ethernet connection, I had it pointing to itself as I don't know what to put for "gateway IP" as that is automatic So, just to check my connection, here I am pinging google (from the gateway computer which has the dialup modem) once a dialup connection has been made.
Code:
lancer@lancer-desktop:~$ ping www.google.com
PING www.l.google.com (74.125.237.17) 56(84) bytes of data.
64 bytes from 74.125.237.17: icmp_req=1 ttl=55 time=179 ms
64 bytes from 74.125.237.17: icmp_req=2 ttl=55 time=176 ms
64 bytes from 74.125.237.17: icmp_req=3 ttl=55 time=158 ms
[Code]...
What do I need to do in order to make Ubuntu of my gateway computer stay connected to my dialup but also simultaneously share an ethernet LAN to my wireless router and feed traffic to the other computers from there? I have googled this but some of the most promising instruction (e.g. http://www.ubuntugeek.com/sharing-in...in-ubuntu.html) call for packages like dnsmasq or ipmasq which seem defunct now in Ubuntu 10.10. Other pages seem to suggest dual-networks "can't be done" in Ubuntu [URL].. (what!?! I had it before my other gateway died)
i installed ubuntu along side of xp, and i cannot get my wireless to work. the drivers that are installed in xp work great, and i can access the internet, but do not work in ubuntu.
View 3 Replies View RelatedI have a Belkin Enhanced Wireless USB Network Adapter Model # F6D4050 v2. The drivers are for windows but the windows wireless drivers app doesnt work. I see a tutorial for a linksys that appears to have the same chipset, but I am not sure if any of the steps need to be modified, also my kernel is a bit different. Here is my kernel:
[code]...
On a remote system, when all you have is the ssh CLI -
How do you find out the ip addresses for:the Gateway
the DHCP server
the DNS server
Don't need to make any changes.
Which commands will display this info?
Recently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.
View 2 Replies View RelatedI was wondering where to find the drivers for my D-link adapter. It says on the box that it has Linux support, what does that mean? I have already used it without any drivers and it works for a bit but after a week or something it doesn't work anymore (it is connected to the network but no download). What should I do? Would installing the drivers solve the problem?
View 3 Replies View RelatedI was wondering if anyone knows how to find internet connections on ubuntu?i can`t find anyone, and i have installed ubuntu on a mac laptop!
View 2 Replies View RelatedAfter I put my laptop for a system update, some of it [sounds] works selectively in my browser when I am watching ..... but when I am playing some musics on my desktop, there's no any sounds coming out. Then I noticed that my Output is still in 100% but 0.00db and a Dummy Output.
I already tried some steps I saw in some threads that has the same problem too but it became worse, I no more [completely] sounds anymore.
I'm running ubuntu 10.10 on a gateway NV7915u laptop that has built-in bluetooth. However, ubuntu doesn't seem to be detecting it (it tells me that my computer doesn't have any bluetooth adapters plugged in).It seems that Fn F6 is supposed to enable bluetooth, but it doesn't seem to actually be doing anything
View 6 Replies View RelatedFor some reason, ubuntu cannot find local wireless networks. In fact, the Broadcom wireless card Ralink RT5390 802.11b/g/n seems to be incompatible with ubuntu. I've tried numerous 'solutions' on the Internet, but none of them seem to work on my computer. Tutorials I've visited have recommended downloading the b43 drivers from the Synaptic package manager and also the bcmwl-kernal-source package. Nevertheless, the wireless never turns on and Additional Drivers never shows anything at all. After several exasperating hours of trying to get my wireless running I've decided to turn to the forum for help. I'm sure there's probably more information I should supply, but I'm honestly not sure what that would be.
View 2 Replies View Related
