Ubuntu Networking :: 9.10 - No Wired Connection (Now Offline)
Jan 22, 2010
I have two PCs one has Windows XP the other has Ubuntu 9.10 on it, the Windows PC has no problems getting on the Internet (I'm posting this with it) and getting an IP address from the wired router. The wired router I have is ONLY wired it does not have wireless at all, it is currently setup to hand out IP addresses between 192.168.1.2 and 192.168.1.254.
The Ubunutu 9.10 PC worked great last night surfed all over the place for hours, then finally shut it down last night when I went to bed, shut down appeared to be normal like it always does when it shuts down, then this morning when I booted it up it gave error: "WIRED NETWORK - disconnected you are now offline".
After i install it i lost my internet connection . i got a message " Wired Network " " you work offline ". i use cable ADSL ,.... my Pc information HP Pavilion 6700 running with both Window 7 & Ubuntu 10.10 note... my network connection work correctly on W7.
I just installed Ubuntu 10.04, complete noob, but I can't connect to the internet. I connect the ethernet cable, select auto ethernet and the icon animates for about 30 seconds. But then I get a notification "Wired network Disconnected - you are now offline".
Don't know what other information I should provide. I tried a few things from different posts like editing the dhcpclient.config but don't really know what I'm doing and none of these worked anyways. I'm not even sure if they were solutions to a similar problem! I'm using the same connection on my Mac OS 10.4.11 (different machine) and I have no problems. Could I use these same settiings in Ubuntu? I don't know what the different fields represent or what I should input in manual settings.
I have the "Work Offline" problem: when I boot up, the icon on the toolbar tells me I have "No network connection". This is not quite true, since I can access the first page of any website - only subsequent pages are inaccessible. I get a message saying that Firefox is offline. However, when I uncheck "Work Offline" in the File menu, it makes no difference to this behavior.
The problem is on my Ubuntu Dell desktop, which is connected to the internet with cable broadband via a D-Link router (wired connection). It has worked fine up till now. I use Ubuntu 10.04 and Firefox 3.6.11. I am writing this on my Ubuntu Dell laptop which is wired to the same router, so I assume the problem is not the router. I have tried various strategies suggested in threads on these forums, including editing about:config, changing "allow" to "deny" in some lines of /etc/dbus-1/system.d/NetworkManager.conf and changing from Automatic (DHCP) to Automatic (DHCP) Addresses only, but no luck so far. The contents of ifconfig are:
I have installed the driver of my Broadcom Wireless card BCM4312 ( Acer extenza 5620 laptop) and when i try to connect to my wireless connection it just try to connect for a while and then go offline i tested another usb wireless card and still no success
I just installed Ubuntu 11.04 desktop on my desktop in dual boot with Windows 7.
Heres my problem, I am unable to connect to the Internet even though my wired Ethernet connection says it is connected normally. The wierd thing about this is that I also have a wireless card in my desktop and when I connect through that I am able to connect to the Internet. I am connecting to a router that is functioning as a repeater to my main router/cable modem. I have tried to solve this myself but am having no luck. Ironically, earlier today suddenly my ethernet connection worked for a few minutes without me modifying anything.
The output of some terminal commands are below.
However a pint to that ip address (my router) is successful.
Hosts.allow and hosts.deny are both fine (not blank but no entries)
I am using ubuntu in my new office, and I can't get the network working. The "official" OS installed was a Windows, and it has a special "dial-up" app for the LAN connection (not wireless). My network admin is apparently not helpful, since he actually knows nothing about the internals for the "dial-up" app (he did not even ever heard of TTLS, PEAP, MD5, etc), and claimed that no OS except for Windows can work...
Well, I have tested various configurations with my Mac laptop, and apparently the LAN connection requires 802.1X authentication, and it's using a very weird combination "TTLS+PEAP+MD5" (if I check these options in Mac OS X, the connection works). However, in NetworkManager, I can't select both TTLS and PEAP, and moreover, TTLS does not work with MD5. So, is there anything I could try?
I've had a computer running Ubuntu connected to my TV for a few weeks now, but as of yesterday, I can't get it to keep a connection to the Internet. Everything works well for an hour or so after a reboot, but then no WAN connections work. When this happens, no sites load in Firefox or Chrome, I can't ping Google, I can't SSH to the box from work, and none of the pages I have running on apache load from remote computers. However, all local area connections seem to work fine. SSH from within my LAN takes much longer than usual, but it does still connect.
The situation is I have one machine just installed 10.04yesterday, and I plan to take it as FTP server sharing filesvia LAN and WAN as wellBut after setting up all network withNetwork-Manager found that my dsl connection willdisconnect while my wired connection was connected.
my network-manager setting process is: 1.wired tab: IPv4:192.168.1.x
I have a wired problem in Ubuntu 10.10, My Ubuntu can connect with Wireless network, however it cannot connect to Wired Connection. I installed dual System, one is Ubuntu 10.10, the other one is Win7. Under Win7, I can both connect to the Internet in Wired or Wireless mode.
The more wired phenomenon is: When I plug in the cable, I can see the icon connected in my network manager. But I cannot visit any URLs. By checking the "ifconfig -a", I can see the IP addr was assigned to my eth0.
installed Ubuntu 10.04 on my Dell 1564. My cabled netwo connection is not working.buntu has been dual booted with Windows 7. Internet connection on Windows is working. I have an ADSL modem connected to my laptop via the cable.I have given the details of commands asked to be execute(viewed various posts).
I recently did a whole system wipe and got rid of windows all together!! Unfortunately, that means I have to start over with the whole networking thing. I know I have a bcm4311, but I have no idea what I have for a wired adapter. I know that I could search through everything to find what I need, but there is so much info for all the different versions. I have ubuntu studio. Can someone tell me the commands to type into the terminal to find out what I have for the wired network card and recommend a place to get the proper "drivers" to get my computer working again?
Running a wired connection through a Linksys router that suddenly stopped working today.I thought this was a ipv6 issue sinced I enabled some of those settings to share a connection with my PS3.I have since disabled IPv6 in Firefox and through the grub. The RealTek adapter will not even show a connection through the network manager when connected.The onboard adapter will show a connection, give me a ip address and MAC but still will not load the internet. I've tried uninstalling and reinstalling both adapters through the network connections, as well as reinstalling Firefox to no avail.I've also tried using Open DNS servers.I cannot ping through the network tools either. Hard for me to paste a ifconfig since I'm on my laptop.I'm running Ubuntu 10.10 (not dual booting).I did some updates this morning but it worked fine for a little while after that, until I tried to connect to my PS3.
i got wired connection using Ubuntu 10.10 and im new using ubuntu pls tell me where i must write the words not to write codes and i don't where i must do it.what is the best version of Ubuntu didn't had that problems?as i saw that Ubuntu 10.10 had same problem for all people.
A while ago i attempted to use ubuntu as my default operating system and it failed, i could not get the shares to work properly and i gave up. Yes i know, may be i should have kept going.
Any way, my problem is, Im attempting to use ubuntu 11.04 now, and this time i am realy keen on going through with this, however... for some reason when i connect my wired connection cable ubuntu keeps failing to connect. this is with the auto eth0.
Can any one help me with this problem? This is one of the major things that i will need to do if i want to switch over to ubuntu.
I recently installed 11.04 on my PC (was running 9.04), and beforehand "tried it out" and networking was fine. I could access the internet no problem.I then ran the install, and fully formatted my HDD (i have 1 HDD for the OS and another for storage)It crashed halfway thorough, so no problem, i just re-formatted the hardrive and installed.However, It didnt connect to the internet, I literally tried every single forum looking for the solution, including editing the Network interface file.After a bit of diggingfound my user privileges did not allow me to connect to ethernet, and randomly use audio devices.SO, no problem I checked the boxes, but it still wont connect to the ethernet now, and it was fine before, tried re-installing twice with full format, but still doesnt work.
I just want to use Internet Connection Sharing (ICS) to connect to the internet. I have done a massive amount of troubleshooting, but some of it seems to contradict itself, and the only two things that I know for sure are that it used to work, and that my Ethernet cable is not the problem. When I use Terminal utilities like ifup and dhclient it seems that it can not determine IP information, but when I try to put it in manually, the "Apply" button grays out right after I finish typing it in. When I try to connect normally, in KDE or GNOME, the icon acts like it's connecting, then instead of having the connected icon, I receive a notification that "the network has been disconnected", and it goes back to the disconnected icon.
Oh, and by the way, I know that I could probably find a workaround, but I have limited resources, and this used to work. The Linux is a Dell desktop with Fedora 12 and the Windows is a Windows 7 HP laptop.EDIT: I hope that I didn't mess something up, but I accidentally used system-network-config to try putting in the IP address there, and ended up changing it back to the original settings, but the computer is now calling it Auto Ethernet in the taskbar icon, although sudo iwconfig in the terminal still calls it eth0.
It's been a while since i've been trying to deal with this problem but it was useless. I've found many related problems to this, most unsolved and those who had solution wouldn't work for me. I have few mates who have the same problem and still didn't find a solution as well. Here's the problem:
Both on my Desktop and Laptop, the network manager won't recognize that there is a cable pluged on the computer so that it would start my connection. The solution to make it work is pretty simple and its everywhere: use pppoeconf.
Altough that does the trick to make my internet work, i get another problem that i found out to be related to this one, which is: I can't use VPN. Which make me assume that one problem is related to the other, is that on my laptop, which has wireless internet, ubuntu will recognize it and then i can simple use vpn. My desktop, on the other hand, isn't that lucky and does not have wireless, so i can't just use vpn. So far, i've been using vpn on windows when needed, but switching systems is really a pain, not to say i'd rather do that on ubuntu.
Few other suggested solutions were to use 'wicd' and other network managers, altough for some people that did work accoding to what i saw on boards, that didn't really work out for me as well. Wicd coldn't recognize it either. Other suggestion was to check on some txt file on ubuntu, erase few information and let it 'fill up' automatic, it didn't work as well(sorry i don't remember all details on this one).
This problem happened on: First, wubi for ubuntu 9.04 Ubuntu 9.04(normal install.) Ubuntu 9.10 Happened both on my Desktop and my notebook, but the same version i installed on both of them were used on other computers and they did work on them so i strongly believe it has to do with the os itself.
I have the latest version of ubuntu on an HP dv4000 laptop fully updated. wireless worked out of the box. but the wired connection wont start. Problem is with the ubuntu install not the network. But i dont know how to configure it to work.
I recently purchased an Acer Aspire 1410 notebook running Windows 7 home edition. I installed Ubuntu 2.3 and my wireless and network LAN connection is not working. I saw on a link in this forum, someone was having similar problem. However, when i tried the solution that was recommended/suggested to the person, it did not work for me.
what I can do to get my wireless and wired connection to work?
I am having a persistent problem with getting a wired network connection under a recent install of Ubuntu 9.10. The network manager will show the wired network as 'disconnected' after a restart. This is true whether I am connected directly to my ISP's modem, or through the Linksys router that I usually use.The output of ifconfig suggests that eth0 is not being assigned an IP address:Code:I have reached the limits of my own ingenuity.
After installing UNR onto my dell mini 9 and downloading the correct drivers to enable wireless internet (using this site: [URL]), I decided to load ubuntu onto my brothers netbook. After the installation completed, I went to do complete the steps listed in the above article, however I was unable to connect to the internet using an ethernet wire.
We finally got internet in our apartment in China, but my husband was the only one home when the guy came to set it up (on his windows machine).
He connects by plugging in, then clicking a desktop icon labeled "Broadband Connection" where a box pops up with a username, a password box, and some buttons, one of which says "connect".
I am trying to figure out how to set this up on my netbook so that I can use the internet at home too. I have a feeling that even if I had been home when the setup guy came, he wouldn't have had a clue what to do with mine anyway.
On the WinXP machine: Connection Properties state that this is a PPPoE connection, with TCP/IP, QoS, and Deterministic Network Enhancer all checked. Under the security tab, unsecured passwords are allowed.
I'm trying to edit my wired connection but the edit and delete buttons are grayed out. How can I go about getting the available? I want to make sure my connection is checked for all available users. I was able to edit my wireless connection on my laptop fine, just not my desktop.