I just installed Ubuntu 10.10 and updated it completely. Then allowed it to install the nvidia-current package for my nvidia graphics card. I do see the GLX module load.
Code:
[ 11.298] (II) LoadModule: "glx"
[ 11.298] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[code]....
I'm running ubuntu 9.10 64 bit (2.6.31-20-generic) on a Z600 HP. My graphics card is Nvidia quadro NVS450. I am using the Ubuntu Nvidia driver 185.18.36. I am experiencing random, daily system freezes where the system has to be manually rebooted. After installing the crash dump packages I am now getting a crash dump file and it's clear the problem relates to my graphics card.
Is this a red herring or the cause of my problems:
(EE) Failed to load /usr/lib/xorg/modules/extensions//libglx.so
(EE) Failed to load module "glx" (loader failed,
(EE) NVIDIA(0): Failed to initialize the GLX module; please check in your X
The NVIDIA X Server Settings shows a message "Failed to query the GLX server vendor".
Here is my xorg.conf file:
$ cat /etc/X11/xorg.conf
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@crested) Sun Feb 1 20:25:37 UTC 2009
Section "ServerLayout"
[Code]...
I have had this error for way too long. This post will be done in parts. I've had it for months now and I'd like to solve it. Every suggestion on linux forums, ubuntu forums, or some XYZ-linux blog seems to either work for just one boot or none at all. since I have updated my kernel on several occasions, I have also re-installed my NVIDIA kernel module by downloading the run file from NVIDIA's website. It also follows instructions from this post. I have installed the linux header files and the xorg-dev files from repository
I have also tried this.
My hardware (Alienway m17x - VGA compatible controller: nVidia Corporation GT200 [GeForce GTX 260M])
Code:
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
Flags: bus master, 66MHz, fast devsel, latency 0
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
Flags: bus master, 66MHz, fast devsel, latency 0
[Code].....
I just finnished my slackware upgrade to current (as you may know from my previous post), and now i am facing another problem.When i type startx i get error:Failed to initialize the GLX module,...,try reinstalling the NVidia driverno screens foundOkay, i thought i should reinstall the Nvidia drivers..And then when i ran the driver install file, i got another error:Unable to load the kernel module 'nvidia.ko'....Kernel module load errorWhat should i do now ? Nothing works! New kernel
View 6 Replies View RelatedEvery time I start up my Ubuntu 10.04 install, instead of the graphical login screen, I get an error dialog stating the following:
Code:
Ubuntu is running in low-graphics mode. The following error was encountered. You may need to update your configuration to solve this.
Also in the dialog are several lines of text:
Code:
(EE) <date and time> Failed to initialize the NVIDIA kernel module. Please see the system's kernel log for additional error messages and consult the NVIDIA README for details. ***Aborting*** Screen(s) found, but none have a usable configuration.I'm not sure what it means by "kernel log," or where any error logs might be saved. Any tips? Perhaps if I can find such error logs, posting them will help diagnose the problem.
If it matters, I have 2 monitors, an NEC AccuSync 120 CRT and a Samsung BX2440X LCD. I use them in Xinerama mode with the Nvidia drivers under my Ubuntu 9.10 install and have no problems there. To get normal graphics under 10.04, I have to start up in low-graphics mode, kill X server, reinstall the Nvidia proprietary drivers, and restart the X server. Then I have to do it all over again after the next restart, every time I want to run 10.04.It's very annoying.Also possibly relevant: I use the latest 32-bit Nvidia drivers for 10.04, version 256.53.I've found a few other threads where people had problems similar to this, but nothing exactly like my situation nor any real resolution so far. I hope it can be fixed, because there are other things about 10.04 that I really like.
I keep getting a warning messaged almost every time I reboot about Ubuntu running in low-graphics mode on a Macbook 5,1. This has been happening since Lucid Beta 1.
Quote:
Failed to initialize the NVIDIA kernel module. Please see the
system's kernel log for additional error messages and
consult the NVIDIA README for details.
[code]....
After I finish loading in low graphics mode I have to run "sudo nvidia-xconfig". Then, the next reboot the graphics card driver is loaded properly. Is anyone else experiencing this problem or have an idea how to correct it? I know it is a long shot, but do you think doing a fresh install of the stable release would work?
This problem has bothered me in both my previous install of 10.04 and my current one. Intermittently, booting into ubuntu results in ubuntu running in low-graphics mode, informing me that the Nvidia kernel module has failed to initialize.Running nvidia-xconfig does not help. Removing and then reinstalling the nvidia driver in Hardware drivers does not help. I experience the issue with both the 173 and current drivers.I love ubuntu, but this is making me seriously consider exploring other distros. Perhaps this not a bad thing - after I return from this exploration,
View 1 Replies View RelatedI am trying to get my Debian system running. I have an older Dell Precision 490 with two dual core CPUs. It has 16G Ram, an 150G Intel solid state drive, a 230G data drive, and a 600G backup drive. I have two Samsung monitors attached to the NVIDIA Geforce FX 5xx card. I have been using this machine for several years with Etch, then Lenny, running KDE 3.5. I recently needed to upgrade to Squeeze and KDE4 and have had nothing but problems since. I keep having issues with the video drivers, every time I touch anything the drivers seem to upgrade from the legacy 173 to the current 195.
There have been other library compatibility issues as well (gclib) and the machine has not been stable. This morning the system was running very slowly with X running at 100% (from top) and then the entire system froze. After a hard reboot, X did restart. The Xorg.0.log has the following message:
"Failed to initialize the NVIDIA kernel module! Please ensure that there is a supported NVIDIA GPU in this system, and that the NVIDIA device files have been created properly..."
Problem: computer and graphics card had been running for months without problem. For some reason, last night, things locked up...wouldn't think it's related, but happened when I noticed I was locked out of creating new folders on my usb attached My Book storage drive. So, from terminal I tried to sudo change permissions to read/write. Everything locked up. Now, every time I reboot it states needing to use low graphics mode "Screen, graphics card, and input device settings could not be detected correctly."
When I check the error log I see: "(EE) Failed to initialize the NVIDIA kernel module.."(EE) NVIDIA(0): ***Aborting* Screens found but none have a usable configuration. Fatal Server Error - no screens found"
If I try to then start in safe low graphics mode or restart X, I get the Ubuntu splash screen with the 5 dots that turn red to show progress...but nothing ever happens. I can switch to VT 1, login at command line, and type "startx" and then the graphical desktop loads just fine. Video playback, etc. is perfect and fine - not in low graphics mode at all. System seems totally normal.
However, I have to go through these steps each time I reboot. Also, I noticed that when I try to boot from Ubuntu Live CD I can't. I get as far as picking English as a language, then screen goes blank and goes to power saving mode (no signal being sent). This greatly concerns me as even though I have a work around for now - getting to command line then startx'ing - if I ever needed to reinstall from the CD, it seems I can't.
Some info on my pc:Running 10.04 on Compaq Presario SR1950NX AMD 64 GeForce 6150 LE/PCI/SSE2/3DNow! <- believe built onto motherboard on what I can do to fix? Is this a sign that something is wrong with my video card?
I updated kernel and everything seemed ok, except HD-PVR is locking up and recording only two minutes of every show it records. So, I have gone back to my previous kernel, but it seems that X isn't starting:
Code:
(II) NVIDIA dlloader X Driver 195.36.31 Thu Jun 3 08:27:29 PDT 2010
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[code]....
Fatal server error:no screens found I had done a yum install kmod-nvidia for the newer kernel. I am thinking I need to get the kmod for the current kernel again (2.6.32.12-115.fc12.x86_64 #1 SMP Fri Apr 30 19:46:25 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux), but am not sure how that is done?
I am using ubuntu 9.10; whenever i open up a camera the below lines appear.
libdc1394 error: Failed to initialize libdc1394
I tried to apply below solution but it is not working:
[URL]
have an OpenSuSE 11.4 (Linux 2.6.37.6-0.5-desktop) with XBMC (10.1) installed.During installation of SuSE, I've created a user called "xbmc" and enabled autologin for this user. After XBMC have been installed I added the following to /home/xbmc/.xinitrc - "exec /usr/bin/ck-launch-session /usr/bin/dbus-launch --exit-with-session /usr/bin/xbmc --standalone -fs"... so far so good - everything is perfectly fine..... or at least almost - when trying to play some musik I get the message "Failed to initialize audio device, Check your Audio Settings"... but if I close XBMC, log in to Gnome as root, open a terminal an su to user "xbmc" and start xbmc from commandline it works if I choose "Internal Analog Audio" in System -> System -> Audio Output. Now the spooky/funny parts appears... I check the options in Audio Output I see the following:
With Autologin:
Defaults
iec958
hdmi
HDA Intel Defaults
[code]...
When returning to auto-login - it stops working again... By the way - to be sure that it wasn't a rights-problem, I ended up changing the UID for the "xbmc"-user to "0" to ensure root-privilegies
I am using Ubuntu 10.04 LTS.With the last update, I have installed the kernel 2.6.32-33.And I have the message "module nvidia failed to load" in Xorg.log.0 My "current" nvidia module is 195. I have tried without success to reinstall nvidia. What I must do ? Wait for a new update of nvidia ?
View 3 Replies View RelatedI am running my PC on Lucid. It has been working fine, but suddenly the other day I got an error message when booting, saying that Nvidia kernel module failed to load. I had to boot in low graphics mode. The only thing i can think of that had changed is that I had recently upgraded to latest Linux kernel 2.6.36-25.I have tried carefully following tips on numerous threads on this forum and others, but still no go. I have purged nvidia drivers and reinstalled nvidia-current (also tried nvidia-glx-185). However, when I then do <sudo modprobe nvidia>, I get this message:
WARNING: All config files need .conf: /etc/modprobe.d/lrm-vide, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/bad_list, it will be ignored in a future release.
[code]....
When I go to System>Administration>Hardware Divers, it shows Nvidia-current as present but not currently activated.I have blacklisted vga16fb and nouveau in blacklist.conf, done <sudo nvidia-xconfig> etc.I am at a loss as what to do next, and am still new enough to Linux to not be in a position to fiddle to try fix it myself.
I am thinking about alternatives for VirtualBox (which i like, but the Oracle-story is making me think). After this thread: viewtopic.php?f=10&t=56314 I downloaded the vmware-player (manual, not with the download-manager ) and installed it. Oct 15 15:02:15.614: app-3078584000| Failed to compile module vmmon!
View 13 Replies View RelatedTrying to install the Suhosin module with the php 5.2.9 c5-testing repo...it won't run with the php 5.2.9 testing build (there isn't an updated suhosin package against the 5.2.9 build)
PHP Warning: PHP Startup: suhosin: Unable to initialize module
Module compiled with module API=20050922, debug=0, thread-safety=0
PHP compiled with module API=20060613, debug=0, thread-safety=0
What's the best way to handle this from an admin best practices standpoint? I want to do everything possible to keep the suhosin module tracked by yum for future updating etc. Is it best to try to find a suhosin rpm that is built for 5.2.9 and install it with yum localinstall? If not, if I build the module myself, what's the best path to keeping yum/rpm in the loop on this install for future updating via yum?
Today, I use the vnc tool to connect the server , but it has the following message:
test@xxx: ~ vi ~/.vnc/xxx:1.log libhal.c 644 : Error connecting to system bus: Message did not receive a reply **(gnome-volume-manger:30626):WARING**: manager.c/912:failed to initialize HAL!
The server's os is CentOS 4.7 x86_64, I tried to google for the answer, but had no anything useful information.
Everytime I log into Gnome Desktop I get this message :
failed to initialize a HAL context
Here is the exact error message when I look into auth.log
Quote:
gnome-keyring-daemon[22720]: failed to initialize a HAL context: (null)
gnome-keyring-daemon[22720]: Scheduling hal init retry
I'm on a Debian Linux system.
Everytime I log into Gnome Desktop I get this message : failed to initialize a HAL contextHere is the exact error message when I look into auth.logQuote:gnome-keyring-daemon[22720]: failed to initialize a HAL context: (null)gnome-keyring-daemon[22720]: Scheduling hal init retry
View 2 Replies View RelatedI receive following error when trying to enable strigi. "strigi service failed to initialize, most likely due to installation problem" I have searched internet, obviously not good enough, and i have found nothing. Nothing that would work. i have tried installing openjdk-devel as suggested, soprano. And still nothing. I have same problems on both boxes running Fedora 12.
View 1 Replies View RelatedRecently I started getting pop-up saying:
Code:
Failed to initialize
Failed to initialize packaging backend
This may occur if other packaging tools are being used simultaneously.
under more details i get:
Code:
There are unfinished transactions remaining. Please run yum-complete-transaction as root. I get to terminal, and as a root I try yum-complete-transaction, but it just says there are no unfinished transactions left. I tried to update thru yum, but this is what I get:
Code:
# yum update
Loaded plugins: fastestmirror, presto, refresh-packagekit
Determining fastest mirrors .....
After lots of googling, I tried:
"yum clean all",
"yum-comlete-transaction",
"rm -f /var/lib/rpm/__db*" + "rpm -vv --rebuilddb" + "yum clean all",
Everything else is working well, and I am able to update with "--skip-broken", but I keep getting this pop-ups. I use fedora 12.
Since Livna went down, I've been having having problems with KPackagekit. I disabled the Libna repo by setting enabled=0 in /etc/yum.repos.d/livna.repo, and have been able to update with Yum.KPackageKit fails on me now with the message "Failed to initialize backend. This may occur if other packaging tools are used simultaneously."Then it fails to finish, which causes me to reboot before I can use Yum successfully.Under Settings, I see no indication that it knows where the repositories are, and no way to add repos.
View 1 Replies View RelatedI have 2 NVIDIA card intalled - GT 240 and Geforce 9500.After updating by repo kernel to ver 2.6.37.6-0.5.1 and Nvidia driver by to ver 270.41.06 X server cant start
Part of X server log
347.737] (EE) NVIDIA(GPU-1): Failed to initialize the NVIDIA GPU at PCI:2:0:0. Please
[ 347.737] (EE) NVIDIA(GPU-1): check your system's kernel log for additional error
[ 347.737] (EE) NVIDIA(GPU-1): messages and refer to Chapter 8: Common Problems in the
[code]....
So for now only dismounting one of cards gives working X server.
New install of Mint LMDE (Debian Testing)
I installed Blueman & paired my headset successfully but I get this error message when I connect my headset, "Failed to initialize pulseaudio bluetooth module. Bluetooth audio over pulseaudio will not work". When I go to Pulse Audio Volume Control, it's not showing in my hardware list.
I have error in KPackageKit when i try to install anything or check for updates:
Failed to initialize packaging backend. This may occur if other packaging tools are being used simultaneously.
Details: There are unfinished transactions remaining. Please run yum-complete-transaction as root.
I don't know anything about other packaging tools - I think I don't using any. Yum works fine in terminal. Reinstall PackageKit and KPackageKit files doesn't helped me. I also try to rebuilt rpm db:
rm -f /var/lib/rpm/__db*
rpm -vv --rebuilddb
yum clean all
I'm using Fedora 12 x86_64.
im using a toshiba satellite u305-s2804 laptop with windows 7 installed it has 2gb ram .intel centrino dual core processor,160 gb hd ., what i wanna do is dual boot between windows and opensuse 11.3 which i downloaded today . i went ahead and set up a partion for the linux to be installed on (the space i gave linux is 25 gb) . but during the installation i got this error
failed to initialize the software repositories .aborting the instillation.
I am recently getting a very weird error on my Webmin. The result of this problem I suspect is I am no longer able to log into my Maia Mailguard which is my Spam Viewer.
Quote:[BEGIN failed--compilation aborted at (eval 17) line 1.
restarting miniserv
[06/Apr/2011:23:34:09 -0400] Restarting
[06/Apr/2011:23:34:10 -0400] miniserv.pl started
[06/Apr/2011:23:34:10 -0400] Perl module Authen::PAM needed for PAM is not installed : Can't locate Authen/PAM.pm in @INC (@INC contains: /usr/libexec/webmin /usr/lib/perl5/site_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl /usr/lib/perl5/vendor_perl/5.8.8/i386-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.8 /usr/lib/perl5/vendor_perl /usr/lib/perl5/5.8.8/i386-linux-thread-multi /usr/lib/perl5/5.8.8 .) at (eval 17) line 1.
BEGIN failed--compilation aborted at (eval 17) line 1.
Failed to initialize SSL connection
Failed to initialize SSL connection
i installed firefox 4 and removed the old 3.X version. did a general update that my computer showed me was available then i noticed the first problem. firefox 4 would not launch when i clicked it, it would only launch when i clicked the gnome 3 applications button and then clicked and dragged the firefox logo to the desktop, then it opened. the second problem i am now having which at the moment is more bothersome is that after i closed the lid to my laptop and opened it up again after a while and logged back in and noticed that the ENTIRE gnome 3 environment was gone. no panel no menu nothing just the desktop and a few desktop icons. i tried the command "yum install gnome-shell" but it just sed that gnome 2.31.5-7 .fc14.i686 was already installed so it wasnt gonna do anything, then i tried the "gnome-shell --replace" command and it just said
failed to load "canberra-gtk-module": libcanberra-gtk-module no such file or directory.
I've installed openSuse 11.4 server-mode (text only) on my desktop, and I'm trying to configure IceWM so i'll eventually have it set up so it always boots into text only mode, but I could be able to quickly start icewm via the command line.using Yast, I installed the Xorg server, and icewm.when I type X, the screen goes black and it just doesn't seem to do anythingI found if I hit ctrl+alt+f1 it kinda puts me back into text only mode, but I can't put in commands anymore. The last thing it says on the screen is:
Failed to load module "fglrx" (module does not exist, 0)
I've goggled that error message and the discussions that popped up around it made no sense to me at all. I've never configured X from scratch before, can someone point me towards a tutorial or something?
I cannot find the Xorg configuration file on my newly installed Debian on my tablet-pc, so I followed this tutorial [URL] and ran the command "Xorg -configure", to which I got the following error messages:
(EE) Failed to load module "vmwgfx" (module does not exist, 0)
(EE) vmware: Please ignore the above warnings about not being able to load module/driver vmwgfx
(++) Using config file: "/root/xorg.conf.new"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
[code]...