I have just finished installing 10.04 on my EEE 900A. Stuff works flawlessly insofar as I can tell. The one remaining thing I am still trying to figure out is how to turn_off the touchpad. Is this doable with some utility that I can grab from Some repo??
View 1 RepliesI have posted questions on several Linux forums that asked how I could turn off the touchpad on my new EEE-900A netbook. There is a backstory that is not that relevant, but in a nutshell, I got this tiny low-power computer to be my voice since my speech is impaired. Only the latest Debian has the tools I needed.
After much searching, suggested that I remove the touchpad driver; the command as root: # rmmod psmouse
Did the trick. On the 900A, the protocol that handles the touchpad is the PS/2. Removing the psmouse driver module does not affect my USB mouse, so now I can use my USB mouse and type away with my left hand and bumping into the touchpad doesn't screw things up. In other words: Success. (I am being as explicit as possible so that all search engines will find this.
whenever i hibernate or shut down my laptop,its touch pad automatically turns off..next time i login,i've to start it by pressing Fn+F8(which i think is my laptop custom shortcut).
View 5 Replies View RelatedI am running Ubuntu 10.04 Lucid Lynx LTS. My laptop is an HP Pavilion TX1210AU (TX1000 series). After disabling the touchpad using the toggle button and reenabling it again, it stopped working. I tried restarting my laptop and the mouse worked again only up to the Login Screen. After logging in to my account, the mouse froze again. I tried making a new account and tried logging into it (I'm using it now) and it's now fixed. Does Ubuntu change any user settings everytime the touchpad toggle (on/off) button is switched? Maybe I could just reenable it myself.
View 2 Replies View RelatedI have installed synaptics touchpad drivers , but ubuntu cannot find the touchpad.
View 1 Replies View RelatedI just installed Mythbuntu 10.04 and have my Sony LCD TV connected via a DVI to HDMI cable. The issue I am encountering is that everything works fine until I turn off the TV and turn it back on later, because the screen stays blank and from what the TV tells me there is no signal. I have no idea what can cause this. I checked the TV settings in terms of power saving and turned it all off. I turned off the screen saver in Ubuntu, but still the same issue. My motherboard uses the ATI HD4200 onboard graphics engine
View 1 Replies View RelatedI downloaded the *.iso for a Fedora 10 Live KDE installation. It is currently on my hard drive. I tried burning it to a CD with Roxio using two different methods. The first one was not a bootable method. So I checked the Roxio documentation and burned the image that way. In burning an *.iso to a bootable image on a disc, Roxio asks for three different file types, none of which are *.iso. I selected my *.iso because that was all I had. Then I burned it as a bootable to a CD.
When I tried to boot it, I got a black screen with a message at the top left reading something like there was no operating system available. I thought that was strange, and I do not know what to do.
I have a Hewlett-Packard HP Pavilion dv6000. I had no issues before the upgrade, but after, my wireless driver refuses to turn on the wireless at all. I've seen in most of the posts, people can see the wireless networks but not access them. I can't even get my little orange wireless (off) light to turn blue (on). The "additional drivers" option in "administration" was a bust and I've tried reinstalling the kernel from my original disk iso.
Here is my wireless info:
Code:
03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
I currently have the STA broadcom driver enabled and all I can do is use a cable for internet right now.
I have installed Lucid Lynx and have spent some time setting it up to my liking. I normally use PcLinuxOS and it has a GUI application (mklivecd) that lets you make a LiveCD out of your installation, is there an equivalent in Ubuntu?
View 1 Replies View RelatedI couldn't find a place to post Cent OS questions so don't bite if this is in the wrong place
I have a KeySonic 2.4Ghz Wireless Keyboard with Integrated TouchPad which I am trying to get to work.
Now there are some reviews saying it works straight out the box on Linux. This was almost the case for me.
The keyboard works straight away but the touch pad doesn't work at all not even the mouse buttons
I am running CentOS release 5.3 (Final) Kernel 2.6.18-128.el5
I would really appreciate any advice at all, I have checked the output of: cat /proc/bus/input/devices
Which gives:
Code:
I run Windows 7 (Boo! Hiss!) on my netbook (HP Mini 311c), and I would like to dual boot with Ubuntu. Not the netbook remix, as I just don't like it.
I created a bootable USB with unetbootin, out of the iso, and loaded up. It all loaded fine, except for the fact that the touchpad didn't work. I had to ctrl+alt+del to shut down. What could be causing this?
Laptop is of the Lenovo 3000 Y500 series, 32bit processor. Touchpad does not respond during the installation.Worried if the Touchpad won't work even after the installation..Currently using Windows7.
View 2 Replies View RelatedI recently got a netbook and setup as dual boot between win7 starter and 9.10 (64bit). Win 7 starter is not impressive so i want to nuke it and give the space all to my /USR partion. I am comfortable working with Gparted and assume that i can launch using my gparted live usb and delete the windows partion and then resize the /usr partion.
what changes do i need to make w/ Grub2? I would prefer not to see the Grub menu at all and have it load right the main kernel if possible. Also, if this is possible is there a way to get to the Grub menu during boot should i need to select a different kernel?
how I can activate and deactivate the laptop touchpad?
View 8 Replies View RelatedI have installed Fedora 10 in my laptop. After installation in Fedora 10, im not able to use Touchpad to perform a task like to open a folder/open a window/select a word. I am doing above mentioned operations through left button/right button.
View 4 Replies View RelatedThis weekend I did a distribution upgrade to Karmic, but it didn't go very well. Upon reboot, I see a white ubuntu logo on a black screen. I hear the speakers pop, and the screen flashes several times, sorta like the blank screen is maybe changing video modes. After a while I see what I think is garbled text but is unreadable, and it looks like I can log on even though I can't read anything. Now, booting into recovery mode gets me to a readable prompt. There are no upgrades to apply. Typing gdm from here gets me to the desktop just fine. Also when booting, if I choose an earlier kernel the system boots fine also, except the touchpad doesn't work.
View 1 Replies View RelatedThe "Check if already posted" brings up no results. I've installed Ubuntu 11.04 with Wubi on my Window7 Home Premium laptop. No problems, except that I can't find "System" to make adjustments, specifically:
(1) Disable touchpad (it is disabled in Windows7).
(2) The display is only using about two-thirds of the screen (11.6" Samsung X120). In the Windows7 setup I do have the resolution set at 125% because the fonts are terribly small otherwise on this quite high resolution display.
During the installation I was not taken thru settings screens for things like language, video, like I have been on the very rare occasions I've installed a Linux OS onto its own partition, presumably because Ubuntu 11.04 is being installed as part of Windows7.
Before I present my problems, I would like to write little about those problems which I have solved and some experience of F11. I used preupgrade to migrate from F10 to F11, and I did it with success. The sound didn't work from the beginning, I don't know how but the file /etc/modprobe.d/sound had change or add an option with snd-hda-intel model=3stack, which in my case should be model=zepto...
To run blender I have to run it in fullscreen-mode because otherwise the graphics doesn't agree with the mouse-position. The Intel graphics-driver improvement made a big impression at me. Now it is possible to use blender before it was horrible.
I have not yet figured out how to enabled touchpad scrolling, a feature which I miss very much. My synclient -l looks like this:
[Code]...
I wanted to install Ubunutu on my laptop and it currently has windows vista installed on it and installed using latest Wubi. I selected Ubuntu from dropdown menu after the system restarted. But when the sytem shows the username page to login the KEYBOARD and MOUSE are not responding.
I am using Lenovo Y series laptop and using the inbuilt keyboard/touchpad.
After upgrading my Acer extenza 5620z to debian squeeze(kernel 2.6.32-bpo.5-686) left click was not working on my SynPS/2 Synaptics TouchPad,allthought moving the cursor was working !
I went to debian channel on irc and there was someone who told that I should install a patch [URL] to correct this problem but when I restarted the whole touchpad was not working !!
Here is the output of dmesg [URL]
My Dell Latitude 2100 worked fine with the pre-installed Ubuntu 9.04. I upgraded to 9.10 and the touchpad stopped working. Restored to factory condition and it again worked fine. I re-did the upgrade, this time asking it not to delete the obsolete items.
View 3 Replies View RelatedI've one lenovo 3000 g430 4152 laptop on which i have windows but previously installed debian 5.03 and for enabling the wireless i've to download broadcom b43legacy and install it by compiling because the backports kernel doesn't work with lenovo and after installing debian accidently switched of the wireless by the slide button on laptop
but on next boot i was not able to enable the wireless either by the slide button or fn+f5 which is the key for enabling it the wireless then on some forum i got advise that i can only re-enable by installing windows because lenovo drivers are available for only windows for this model... my question is that is there any solution for it in debian and also there is one more problem that i've to press fn+f8 twice on each boot for enabling the touchpad...
Should I turn ON compiz with 512 RAM on mine AAO or do in need more RAM?
View 1 Replies View RelatedHaving just successfully installed fallout 3 (yippee), one question arises.
Is it possible to turn off (and eventually back on) all superfluous process during gaming ? As an ex-win xp user, there was an app called "game booster", i think, that did this.
The process i have in mind are things like fancy compiz settings, dockbar X, and any upgrades that might be taking place in the background.
Again, it is important that i can restart these functions after kicking super-mutant ***.
I just did a clean install of Ubuntu 11.04 on my PC. Installation went smoothly, and I can boot it and log in.
If i leave it there running, nothing happens, but as soon as i try to run an application (Firefox, Update Manager, etc), the screen turns off and I can't do anything else anymore except reboot.
I was able to apply the latest updates using apt-get update from the terminal (one of the very few apps that doesn't turn the screen off), but can't get rid of the problem, what can i do?
My PC is a Intel Core i5 PC with a Nvidia Gefore 210 graphics card.
I was able to install the proprietary drivers for Nvidea, no change. Both Unity and "Ubuntu Classic" have this issue
I have Ubuntu 7.04 and i am newbie, recently i installed Skype 2.1 Beta for Linux.
When I start Skype everything is fine but the moment when i Sign in, Skype closes by itself (or maybe something else close Skype)
I'm using a laptop that doesn't have a numlock key and would like to be able to switch numlock on and off without having to plug in an external keyboard.Is there a command or app that will let me do this?
View 9 Replies View RelatedI have been using Ubuntu 10.4 trouble free for the last week or so with the exception of one problem. Without warning, my computer shuts off. When I turn the computer back on, it skips the log in page. The turn off is very abrupt and happens without warning. It happened twice when I first installed the OS and has not happened at all until today when it happened twice again. Is this a common issue. It seems like a very odd way for a computer to crash.
View 3 Replies View RelatedI'd can't seem to find a preference to turn off gedit's default behaviour of opening a new file in a new tab. I'd like it to open in a new window, so I can view two pages of code side by side. How can I convince gedit to open a new instance?
View 2 Replies View Relatedi think i just got the reason why my ubuntu 10.04 live DVD crashes. i can be due to hardware acceleration if its set to that by default. so how do i turn on software acceleration? some command or something?
View 1 Replies View Related