Ubuntu Installation :: Wireless Not Working After Lucid Upgrade
May 1, 2010
After upgrading from Karmic to Lucid, no wireless networks are found on my computer�an acer travelmate 5510. On Karmic, wifi worked flawlessly "out of the box"�no windows drivers or anything needed. I have checked under Administration/hardware drivers; it tells me "no proprietary drivers are in use on this system." Cabled internet access through my wifi router works fine. How to get wifi up and running under Lucid. Despite having used Karmic for a while, I am relatively new to the inner workings of Ubuntu / linux systems, and really don't know where to go from here.
Recently, I installed a fresh 64bit Lucid Lynx on my Lenovo B450 laptop (previously on Mint8 64bit, based on Karmic). It's been really nice and speedy except for one thing - USB transfers to thumb drives and external hard drives were really slow (just like in the older Ubuntu releases). I had found some forum discussions on a fix to this by way of a kernel upgrade so I decided to go for it.
Went ahead and downloaded the kernel DEBs from [URL] and installed them. Voila! USB speed issue was fixed! Everything else seemed to work fine, except for some minor troubles with burning CDs and DVDs (I think I need to upgrade the drive's firmware - pretty bad situation as the update only runs on Windows).
However, the one 'bug' or 'annoyance' I noticed straight away was that my wireless wouldn't autostart after booting into the OS with the new 2.6.34-020634-generic (x86_64) kernel. I'd have to right-click on the NetworkManager icon on the notification tray and left-click '[ ] Enable Wireless' to flag the checkbox and my wireless would come right up and work ok (WPA2 at home, WEP at the office). Not a major problem, but this has been pretty irritating to say the least.
I just upgraded to Lucid Lynx, and like most people, I'm getting the black screen during boot. So, I went into the grub edit screen, and I tried every variation of the nomodeset fix I could find. So far, nothing has worked. I don't know what graphics card I have, but it's always given me problems.
After upgrading my wife's machine from Karmic to Lucid 64bit, USB drives will not automount and do not show in Nautilus. If I lsusb the drive is shown. I have tried several things - installing hal, removing the legacy floppy in the BIOS, sudo modprobe -r floppy and rebooting but nothing works.
I have tried with several flash drives, all work and automount on my computer (a clean install of Lucid) but none will work on the upgraded machine.
i have a sony vaio VGN-NW150J laptop that was running lucid and had wireless no problem but when i upgraded to maverick i lost all functionality of my intel 5100 agn wireless card. when i run iwconfig this is what i get
Code: iwconfig lo no wireless extensions. eth0 no wireless extensions.
and on bootup it flashes something about no suitable unicode found i can't get a good look at it maverick boot up too fast.
Summary: a long-working config involving a 1st-generation Ipod Touch with v1 firmware, Ubuntu, and Amarok 1.4 stopped working when I upgraded to Lucid.
A few years ago I was given a 1st-generation Ipod Touch, running the original v1 firmware (I never upgraded to the v2 firmware because v2 wasn't jailbroken at the time). I took it to a friend's place to activate and jailbreak it with her Mac laptop (I didn't have a Mac or Windows machine to install Itunes on; have been Linux-only for many years). Once jailbroken, I was happily able to use it with Hardy, Amarok 1.4, and ipod-convenience (which supply ipod-touch-mount/ipod-touch-umount).
This continued through upgrades to Intrepid and Jaunty. I didn't care for Amarok 2 in Jaunty, so I installed Amarok 1.4 from the ppa someone else made available. I continued to use it through Jaunty and Karmic, without any problems.
Last week I upgraded to Lucid. Syncing Amarok 1.4 to the Ipod Touch no longer appears to work; the Ipod fails to recognize any music transferred onto it (standard "No Music - you can buy music at Itunes" error screen), so I presume this is a libgpod/hash error. I have the FirewireGuid properly set in the .../Device/SysInfo file, as I always have.
Every time I use the Amarok Ipod "connect" function (which runs ipod-touch-mount) it tells me no valid Itunes db was found, and asks to initialize the db. I can then transfer music to the Ipod, and successfully disconnect, but it's not recognized on the Ipod after a respring or reboot.
I've tried RhythmBox and gtkpod briefly with no luck either.
Relevant installed packages:
Code: ii amarok14 2:1.4.10-0ubuntu3~ppa5 Amarok 1.4 series ii amarok14-common 2:1.4.10-0ubuntu3~ppa5 architecture independent files for Amarok
[Code]....
Edit: a little more info: after I let Amarok initialize the Ipod Touch and transfer a song to it, the iTunes.db that gets created on the Ipod is 0 bytes long. I presume this is the source of the problem, and indicates something is going wrong with libgpod's creation/editing of the db.
what I should do from here? I've tried removing the DB by hand, but it makes no difference - the subsequent operation to initialize the db results in the same 0-byte file.
after having tried out almost all suggestions found here and elsewhere on the internet, i'm somewhat at my wits end The situation: I'm running Kubuntu 32Bit Version (at the mom 10.4) on a HP-Compaq 6735s (AMD Processor, Vanilla 32Bit Install). My first Install was last year with 9.4 and the Broadcom 4322 wireless worked like a charm after installing the proprietary STA-driver under System -> Hardware Drivers. As the update didn't work out really without glitches, i did a fresh install and lost my wireless. I tried various combinations and tutorials but to no avail. My card is found, the driver installed, but i cannot access my access-point. I can SEE the access point (and all my neighbors'), but knetworkmanager does not seem to do anything. To be sure, I installed wicd (nice tool by the way). Trying a connect here told my my credentials were bad (incorrect passphrase for my WPA2 Personal auth), which is not true. I tried connecting without security, didn't get an IP. So it seems somehow the card is working, but all functions needed for passing information to the access-point are unavailable.
This is what I tried:
both broadcom-drivers fw-cutter installing the driver by hand
Installing the driver via Hardware Drivers produced the same results as any other, viz the card is working, but not connecting. Unfortunately knetworkmanagers error messages are a bit sparse, or rather non existant. My guess is that somehow the firmware is not properly loaded (or the wrong type??).
I started on ubuntu 8.10 and my wireless card has always worked,Since i did a fresh install of ubuntu 10.04 it still seems to work to a point.I can see networks, click them and use a password to connect but it never seems to carry on, I typed the password correctly and after a minute it asks for it again.I have read a post about problems other people are having and that i need to install a different program.But i cant install another program if there is no wireless as apt-get doesn't work without internet connection.So... I need to download something that will fix it (possible update if one has been released) to xp (partition) then access xp partition from ubuntu and install it.
I've just completed switching both my laptop and desktop from Ubuntu 10.04 to Kubuntu 10.04, all seems to be working well, except that I can't get my Virgin Mobile HUAWEI E160E wireless broadband modem working. I used to have it working flawlessly in Ubuntu, I've used the smae step as described in this post: [URL] that worked for me with Ubuntu, but the Wireless Broadband tab is greyed out under the manage connections dialog. I'm running the 64-bit version of Kubuntu BTW.
I recently installed 10.04 and everything Just Worked.Before Lucid, I was using 9.04 and had successfully gotten my Broadcom 4306 working perfectly... which is why I think the Lucid install went so perfectly.Well, after a botched hiberation (Dell Inspiron 9100), my wireless is dead in the water.I've tried "ifdown", "iwconfig", "/etc/init.d/network restart" and "force-reload", 'modprobe -r b43'
1. D-Link DWA-643 Xtreme N Express Card Adapter The onboard wireless for my HP tx1000z stopped working a long time ago. This wireless adapter is in my express card slot.
The device it's properly recognized and iwlist scan even list the networks, but the "activate wifi network" on the network manager on right-top of the screen it's grey and therefore cannot be activated. This seems to be the problem ( rfkill list ouput ):Quote:
1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes
i tried update-manager -d from GUI and asked to downlaod 678 MB...so i downlaoded the i386 iso 685 from cdimage.ubuntu.com/alpha-3..now how to upgrade to 10.04 lucid alpha 3 from 9.10.
I'm currently upgrading my laptop, and it has completed the step "Getting new packages", and is now onto "Installing the upgrades".It says it is going to take another 2.5 hours, but I am leaving work soon and want to take the laptop with me. Is it safe to disconnect it from the internet at this point? I don't want to fudge up the install, but I don't want to have to leave my laptop at work all weekend (or have to come back and pick it up at some point).
I upgraded successfully last night from Hardy Heron to Lucid Lynx, but have no sound now. After searching around I can see that this is a fairly common problem. But none of the proposed solutions that work for other people have yet worked for me.
If I type 'alsamixer' at the command line, everything looks fine. There are no 'MM's indicating something being muted. I tried removing and reinstalling alsamixer and pulseaudio with no success. Edited lines 45 and 46 of /etc/pulse/default.pa with no luck.
I have a dual boot system with Win XP and Ubuntu (using grub boot menu). I recently upgraded my Ubuntu from 9.04 (Jaunty) to 10.04 (Lucid) and now I cannot boot into Ubuntu - I just get a desktop with no icons or disk activity. I think this may have something to do with the fact that I answered 'no' when asked whether to replace my menu.1st file, and possibly some others. So my boot menu still refers to 9.04.
cannot boot into Windows XP following uograde from karmic to lucid.
It comes up on the grub list at the start but when I select it I just get a flashing cursor.
Below is the results I get from a boot info script
Code: Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #1 for /boot/grub.
I can't upgrade from Karmic to Lucid,If I try to use the update manager I get a message that says "Can't download release notes. Check your Internet connection". I've tried changing the repository and I get the same message, but I can log in to the Internet, and download and install any program from the repository. I also get regular updates for Karmic so the repository is fine.I tried the command line
Code:
~$ sudo apt-get dist-upgrade Leyendo lista de paquetes... Hecho Creando �rbol de dependencias
I wonder if others have upgraded their Lucid kernel using the deb [URL]..repository. I have been using the repository for some time now without any apparent problems, and have gone from 2.6.36-1, through 2.6.37-10, and am now on 2.6.37-12.
All of these seem to work with no problems at all, but I am just wondering if other users can also report success, or if there are any trip-ups that might occur. I still keep updating the "standard" kernel from the main repos, ie 2.6.32-27, so I have that as a backup, but I'm just very curious about other people's findings.
I read recently about security flaws in the ubuntu kernel, and when I checked my kernel, it is 2.6.32-29-generic. I looked in synaptic, and I have the linux-generic meta-package - which should ensure upgrade to the latest kernel, and yet this is not being updated when I run update manager. There is a linux-image-2.6.35-25-generic, but the advice is not to install this directly (to avoid breaking dependencies, etc.), but to install the meta-package instead. Yet, the meta-package doesn't seem to be doing what is should do.
Right after I type in my username and password and hear the usual login sound I have to wait about 15 to 20 seconds to get the X desktop. The system load average monitor is at its max and starts to become lower.If I log out and in again I dont get that delay. It only happens with logging in after a reboot/power on.I tried to open a console (Ctrl+Alt+F1) before I log in, move back to X and login then jump to console and use htop to see what's eating up my resources during that time with no luck. Everything seems to be normal.
I have an AMD64 system, which I recently upgraded to Lucid 10.04. The system now fails to boot after the upgrade. Recovery mode makes no difference.
When I attempt to boot, I get a series of messages about file systems needing checking, and also some messages from ureadahead-other. (process terminated status 4), though a post here says that status 4 is in fact not an error.
I have sucessfully booted the Lucid desktop install CD in live CD mode, mounted the filesystems, and started parts of my system in a chroot. In that system I tried running an update, and removing plymouth, but it made no difference. how I can get my system working.
I did take a backup of /etc before I upgraded, so I could get back to a karmic install, but the pain in doing so would be considerable, so I would prefer to avoid that if possible.
I made the mistake of trying to upgrade my Karmic (server) installation to Lucid earlier today, after which I've been unable to boot into my server. The server is on OVH, so I can't watch it boot, but I am able to access all of the data from the filesystems via rescue mode. I ran fsck and that came back clean. I also ran the boot info script, the results of which are below.
I know my best bet is to backup what I can and do a fresh install, but I won't be able to back everything up so trying to get this working would certainly be more convenient. I'm sure I'm leaving out useful information, so let me know and I'll post it.
Code: Boot Info Script 0.55 dated February 15th, 2010 Boot Info Summary: => Lilo is installed in the MBR of /dev/sda sda1: File system: ext3
Upgrade to lucid (by running update-manager -d) succeeded with no major error. But when I reboot the computer, the boot splash screen is "Ubuntu Studio" and the login screen's background is a "Ubuntu-eee" png picture. A funny mess.I was able to get to the new boot splash screen by remove --purge ubuntu-studio, which I must have installed sometimes in the past, but I don't see anyway of getting the new theme for the login screen.I have this eeepc for about 2 years and never have to fresh-install Ubuntu except the first time. I much rather not have to fresh-install just to solve some aesthetic problems.I am pretty sure it's due to some package I installed in the past, but I don't see any Ubuntu-eee related package in Synaptic either.
A few days ago I made the mistake of upgrading to Ubuntu 10.04 LTS, and subsequently had nothing but trouble. My volume icon disappeared and for the life of me I couldn't find it or reinstall it. An eerily Windows-like chat icon has appeared next to my login name that I didn't ask for, and more importantly my handbrake program (Matroska encoder) completely stopped working.
I've learned in the past that LTS editions are not normal upgrades, and I should best avoid them. But this one appears from the Ubuntu homepage to be the standard upgrade from Karmic to Lucid. I've had to completely reinstall Karmic on my workstation just to be able to carry on as normal, but the laptop seems to be coping ok with the LTS edition. Can anybody tell me if this LTS is now the default upgrade for Lucid, or is this just a regular LTS and I should wait for my standard one to come out?
I just need some clarification on the best upgrade path for me. I currently have Karmic installed with a separate partition for /home. I want to do a clean install of lucid with the CD.
What's the safest way to ensure my /home partition remains untouched? Should I install lucid overtop the karmic partition and then indicate a mount point for the other partition? or should I leave /home alone completely during installation and then just manually configure the mount point after install?
Edit: I had previously upgraded from jaunty to karmic via the update manager. This worked well but Karmic has felt very buggy overall so I feel a clean install might be best. although the audio is silent when the live cd boots :S
Since my distribution upgrade to 10.04 my VirtualBox guest of XP SP3 will not boot, it bluescreens and reboots. I can boot the guest in last known good config and in safe mode but I have no CDROM. I attempted a tools install over the lan but that resulted in the same blue screen. Tried installing the virtualbox-3.2 beta package and guest tools and had the same results..
