I'm now on ubuntu and I want to install virtualbox on my system i.e. maverick 10.10. I downloaded virtualbox-4.0_4.0.4-70112~Ubuntu~maverick_i386.deb but there was a problem. My software center says "Cannot install 'libqt4-network". I even did it with terminal but same problem: 'Cannot install 'libqt4-network'.
View 2 RepliesI'm waiting on a 2TB drive to come in so I can repurpose my gaming rig for Ubuntu. (Ok, its still going to be a gaming rig but I want to do 90% of my work/gaming in Linux) I'm thinking that rather than dual-booting I want to run the windows side of the house from a VM via Virtualbox.
Ubuntu runs fine with my hardware atm (have 10.10 installed on a secondary sata drive) and recognizes the RAID array that windows is currently installed on (gigabyte 870A-UD3 motherboard, I think Ubuntu's using fakeRAID to mount and view the drive, not very knowledgeable on raid and had the system built for me, but I know I'm using the gigabyte on-chip bios configuration for the raid)
I'd like to know:
1) if anyone knows of a good guide for dealing with this particular RAID controller beyond my owner's manual. (I read that 10.10 fakeRAID pretty much sets itself up)
2) should my win7 partition for the VM (I'd like it to be a dedicated partition so that I can boot into it if I have to do something in windows that Virtualbox can't handle) be on the Raid Array or the 2TB WD Caviar Green (low performance/power consumption drive)?
3. since I have a 2tb raid 0 array and a 2tb drive coming in, can I setup raid to mirror the contents of the 2 raid 0 drives onto the WD Caviar drive or do they all 3 have to be identical drives. (I think the other 2 are 1TB WD Caviar Black drives)
4. Any particular advice on partitioning? I was just thinking of /, /home and swap being separate on the raid but otherwise leaving the standalone drive as one big partition or splitting between windows partition and an otherwise large storage space.
Setup:
1. Microsoft Windows 7 64-bit Professional HOST Operating System
2. Oracle VirtualBox 4.0.6r71416 on top of Windows 7
3. Ubuntu 10.04 Lucid Lynx 32-bit GUEST Operating System in VirtualBox
I successfully installed the above configuration on May 15, 2011. I had some difficulty getting the Host-Only VirtualBox Adapter to work. I was forced to make a subtle change to the Windows Registry in order to get the Adapter to work correctly. I was successful. I used the Debian Update Manager to update my installation of Ubuntu. Nothing changed on the Windows 7 side. Now, Windows 7 says that the Host-only adapter is enabled, but I don't have a connection to the Ubuntu OS. I can't use PuTTY or WinSCP. When I invoke ipconfig on the Windows side, 192.168.56.101 is the IPv4 address. When I invoke ifconfig on the Ubuntu side, there isn't anything.
I am using ubuntu 11.04 through virtualbox on win7 with a gtx460 if i install nvidia-current to access the nvidia cp on reboot it locks up.
and there are no drivers in the list when using the additional drivers feature through ubuntu which is why i installed nvidia-current. i just want to see what this unity is about and have full scale resolution supported by virtualbox and my vcard as well as my monitor.
Win7 x64 host with Virtualbox installed running Ubuntu 32bit guest OS. I have Samba installed and I am sharing a folder to have read access from Win7. The folders I tried to share (here 'folder1-3') have been added in the conf.d in etc/samba/ like this - I used these 3 variants, all showed the same problem:
Code:
[folder1]
path = /data/mp3
read only = yes
guest ok = yes
[code]....
While I can connect to all of these from Windows and map them in Windows Explorer, I am unable to serve those files using my FTP server that is running on Windows. The folders simply do not show up when I add them as folders to serve in FileZilla. The problem I am assuming is causing this is the fact that FileZilla is running as a different instance and not on an administrator level. I cannot however add any users to the permissions list on the Windows side. The 'security' tab of the mapped folder shows the following Users:
EVERYONE
root (Unix user
oot)
root (Unix group
oot)
None of these seem to have rights to 'read' or 'list folders', the only permissions listed are 'special permissions'. Does anyone know how I can assign the group EVERYONE privileges to read and list files and then be able to serve this shared folder through my Windows-run FTP server?
I have a Win7 laptop with the latest version of VirtualBox installed. It's a dual core proc with ram to spare. So, I installed Slack64-13.1 and it rocks! I'm really impressed that Slack is running at what appears to be native speed, but in virtual machine. Hardware response is normal, WIFI and LAN are both working great for my normal tasks.So, I downloaded a few much needed patches, and new ISO image for one of my old desktop PCs. Now, my problem is I can't connect my USB cdwriter to my virtual slackware or share folders in the Win7 install with the virtual slackware. I read a few of tutorials on the Oracle VBox website, and several of the ones here on LQ, and none of them seem to solve my problems.
View 3 Replies View RelatedJust installed Ubuntu 10.10 onto my new netbook from a USB stick. The laptop came with Win7 Starter, which I kept on a small partition. Installation was apparently successful, but when I start up the computer, it will go straight to Win7 and GRUB doesn't appear.
View 9 Replies View RelatedI had vista installed, then I installed Win7 on a dif. partition. Then I installed Ubuntu 11.4 over the vista partition (formatted first), and now I can't get into Win7. I'm really at a loss. I've tried the Win7 disk, and it doesn't detect the Win7 installation. I've also tried sudo update-grub, and it doesn't seem to detect the win7 install either. I've tried making the Win7 partition bootable using gpart as well. I'd like to dual boot Win7 and Ubuntu, however I need to do that.
View 9 Replies View Relatedi installed ubuntu after windows 7 but now i cant boot windows 7 i tried the start up repair and I've read through some questions answered on here and int figure out the problem i don't want to uninstall ubuntu unless it's my only option
View 9 Replies View RelatedI have been running ONLY linux (ubuntu) on my computer for years now. However, a friend sucked me back into the world of MMO's (angry fist @ RIFT). So, I decided to pick up a new disc, slap windows 7 on it and now want to dual boot.Basically I had to do some disc juggling to get windows to play nice. So my windows drive is now first, then my Ubuntu drive second.Its been a while so I'm wondering how involved / what would be the steps to get grub2 to chainload into windows7 (in my head I want to say I'm going to boot into the live cd, mount the windows disc and reinstall the loader to the windows drive since its the first disc in the chain?)
View 1 Replies View RelatedI just installed win 7 and now can't install fedira 13 on the partition that i made for it on the same drive. The problem is that after installation of win 7 i lost the ability to boot form cd. In bios i still have cd set up to boot first and drive second, but win 7 did something that overrides bios set up. I even tried Esc for boot menu, then i select to boot form cd, but it still boots in windows.
View 1 Replies View RelatedI have installed Ubuntu 10.04LTS on my entire hard drive of my laptop. It's been smooth ride, of course. I want to resize my drive and install windows 7 on the new partition. How do I do that? I have installed Gparted. I have ubuntu installation disk. I want Ubuntu to be the default OS and I want to log on to wndows 7 when I want to from the boot menu. How do I do that?
View 9 Replies View RelatedHere is my dilemma at first grub loads and I have this options:
1.ubuntu 9.04 with a new kernal (update via-- system update)
2.ubuntu 9.04 with old kernal
3.recovery
4.......
5.windows.
And inside windows there is another boot screen for
1.win-7
2.vista
Now I want to remove win-7 and install 10.04 in its place I want the safe/proper procedure to do it if there is already a thread like this then direct me there as I searched and did not get it.
I installed ubuntu 11.04 to my Compaq Presario CQ61-402SA (Dual boot with windows 7 Home premium 64-bit, Via a partition) And now I can't get back to my W7! Disk Utility says that it is "unallocated"! It had lot's of important info on it! Sorry for urgency, but it's important I get this OS and files back, intact.
View 9 Replies View RelatedAfter installing Windows 7 my computer doesn' t ask which OS to start. I starts with win7 automatically. How can I start my computer with OpenSuse?
View 2 Replies View RelatedI'm having serious troubles to install ubuntu-10.04.1. My raid is an hardware raid with intel chipset. Note that win7 is already installed and working with my raid. I made some space from windows, to install Ubuntu (40gb). First, I run the installer, everything seems to be fine. I choose to install Ubuntu were there is the most space free (sorry, I'm not sure about the real terms used there).
Then my partition with the vista loader appears. So the installer can see my raid, and should work fine (everything is detected correctly). But once I'm in the end of the installation (around 95%), a pop-up appears, and tells me that Grub can't install in /dev/sda and it's a fatal error. I can choose an another destination, but it doesn't seems to work.
I bought ASUS K50c with SIS graphic card and have win7 on it (i install it alone).I want to install ubuntu!I found installation of ubuntu 10.10 and tried to install it. There is a huge problem with my graphic card because resolution is 800*600! I found installation of ubuntu 10.04 LTS and tried to install it. Again problem. I tried to download drivers from www.sis.com but there are tar.file and i don't now what is that or how to install it.In windows I now how to install anything, but there is a problem.I am ready to install any version of ubuntu just to solve this problem.
View 2 Replies View Relatedhow to install virtualbox on ubuntu 7.04. I tryed to install VirtualBox-3.1.2_OSE from virtualbox.org and following the instructions i have downloaded it using terminal but i dont know how to install it .
View 3 Replies View RelatedI am a major noob to FC12. I need to install Windows 7 Pro and FC12 dual boot. I first used the windows CD to create 1 250 Gig partition on my 500 Gig HD. Of course windows created the 100 MB system partition. I left the rest unpartitioned. Windows installed okay. I then booted to the KDE FC12 Live CD and installed FC12. I specified to use the Free Space remaining on the HD. The installation finished but now only boots into FC12 and does not prompt me for the OS I want to boot.
View 3 Replies View Relatedmy error when trying to run a VB (Virtualbox). Error as copied from error box. install the virtualbox-ose-modules package for your kernel and execute 'modprobe vboxdrv' as root. VBox status code: -1908 (VERR_VM_DRIVER_NOT_INSTALLED).
[code]...
I get this when trying to launch a VB after making one with wizzard.
I am currently running VirtualBox OSE but I need USB support. If I install the closed source version, is it possible to have it use the OSE's virtual machines or will I have to redo all of it?
View 2 Replies View RelatedNew to Linux and am wanting to install ubuntu 9.10 or 10.04 on a single separate 80gb drive. I have Windows installed on 2 80gb drives in Raid0 (nvidia controller) .I have installed 9.10 but Win7 will not load from the bootloader : gives me the error invalid signature. I've looked around and tried a few things to get it to load with no success.. is the Raid0 the issue?
If I try to install 10.04 it will hang and eventually errors out, I believe on the raid drive because it comes up with dev/mapper/nvidia_hhfbdccf1..
I have installed both 32 and 64 bit versions of Ubuntu 11.04 in VirtualBox 4.0.6 and have installed the VBox Additions. When I try to add new software or update software I get a package operation failed error.
installArchives() failed: Setting up tzdata (2011g-0ubuntu0.11.04) ...
Use of uninitialized value $reply in scalar chomp at /usr/share/perl5/Debconf/FrontEnd/Passthrough.pm line 66.[code]....
I have used the same install media to install Ubuntu on a stand alone system and it works fine.
I want to install Debian 6 on an USB via VirtualBox. Then i gonna take the USB and putt it in on another computer, and boot it from there.
I have two questions:
1. How do I install Debian 6 on a USB via Virtualbox?
I have download Vbox from this http://download.virtualbox.org/virtualb ... 12-Win.exe (i use winXp now).
2. How do a boot the USB via a floppy? My old computer, who i want to install Debian 6 on it, cannot boot from USB beacuse the BIOS dont have "Boot from USB". I have USB 1.0 i think.
I am trying to take a look at Fedora for the 1st time and usually like to have a good tryout of a distro in VirtualBox.
Firstly, the live cd image boots up fine and seems to work ok except for a Kernel crash at the beginning of the gnome session, but it does enable basic usage within the live system.
But, when trying to do an actual hd install (still within VBox) Fedora 14 just keeps on crashing the VBox??, every install attempt just aborts, I have given the virtual machine a 20gb virtual hd, 2gb ram, 128mb video ram and have not applied any "unusual" extra settings. All versions of Ubuntu, Mint and PCLinuxOS work flawlessly within VBox.
Has anyone else tried installing into VirtualBox here?? (not just running the live environment)
I've wasted a good few hours with this, is it just that some distros dont like VirtualBox or is this indicative of what Fedora would be like on a real non virtual install??
ps, I have the latest VirtualBox fully updated and a flawless host (Mint 9), and perhaps I should add that I'm not a Linux expert and have only been using Linux for just under a year now.
I used to have my ubuntu 10.04 running with a virtualbox for a windows xp. I remove that virtualbox and create another one, bigger, with 10gb. On the process, my computer freezes.. now I'm stuck on that initramfs screen.I really need to recover my linux (I have apache, mysql, samba, all up and running).I can reach "grub" booting with right shift pressed, but I really don't know where I have to begin.
View 3 Replies View RelatedSo i installed debian squeeze in virtualbox with xfce and i thought that it was persistent. when i powered down the virtual machine and started it up again later I only had the option of installing it again. Do i use save state to keep it in the installed stage? would i have to do that each time i made a change? i want to make sure so that i don't keep having to re install it.
View 7 Replies View RelatedI'm looking to install either vmware server, virtualbox or another solution.
Which works the best with fedora 11? I'm interested in USB and performance.
btw, I wasn't sure which forum to put this in
I want to install Fedora by live disk on virtualbox.
1. I ran the live disk, it works.
2. I click "Install to Hard Drive", it shows normal.
3. I complete the installition and reboot.
4. The live disk ran again, where is the OS installed on hard drive? or it was not installed at all?
I am running OpenSuse 11.3 64 bit and I just tried to install Virtualbox 4.0.0-22.1 from the Virtualization repository.
--
ttblum@toddb05:~> VirtualBox
VirtualBox: supR3HardenedMainGetTrustedMain: dlopen("/usr/lib/virtualbox/VirtualBox.so",) failed:
[code]....