Ubuntu Installation :: Can't Run On Pc - "_" Blinking For A Few Seconds And Then Goes Black
May 5, 2011
I had burn an image of ubuntu 11.04 for AMD 64, but I have problem with running it on my PC, when. Whenever I trying to try ubuntu or installing it from the live cd, there is a "_" blinking for a few seconds and then goes black. I tried the disk on other computers it worked well. I tried to run ubuntu 6 and it worked. I have AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ MSI K9N6PGM-F (MS-7309) NVIDIA GeForce 8600 GT
View 4 Replies
ADVERTISEMENT
Jun 24, 2010
Problem-PC automatically boots into a black screen with blinking cursor. No message or nothing
I have 4 HD. Primary drive has Windows Vista, Secondary no OS installed. Sata1 HD Ubuntu 10.04, Sata2 Windows 7. Prior to installing windows 7 all was perfect but once I did it, grub got all screwed up. The only way I can boot into grub is if I manually select my Sata1 which has Ubuntu on it and only then it allows me to select Linux or Windows OS. How can I change that so it can boot up normally as before? I'm assuming that grub was installed in the primary drive which has vista on it, but once I installed windows 7 it got deleted and when I tried reinstalling Ubuntu, the grub was not installed in the primary drive.
View 9 Replies
View Related
Dec 16, 2010
I have an Acer Aspire One AOA110 that came with Windows XP.
I created a usb flash drive install for Ubuntu 10.10 netbook edition and went through the install process (wiped disk clean, not a dual boot with WINXP).
Before install, I was able to run Ubunut from the usb key with no problems.
At the end of the install, it told me I needed to restart, so I clicked the "restart" button and the removed the usb drive. Nothing happened and it never restarted and just completley hung for about 20 minutes. I manually shut down the computer by holding the power for 10 seconds and then rebooted the machine. Now all I get after the "acer bios" screen is a black screen with a blinking cursor. If I press any buttons, the computer beeps at me.
View 9 Replies
View Related
Feb 10, 2011
I have rebuild my system, with an Asus motherboard M4A88TD-V EVO/USB3 with radeon 4250 integrated 8 Gb memory
Athlon II 4x 640 2 x 1 TB sata3 WD Harddisks I installed 10.10 64bit, and ran through the whole install with the alternate CD without problems, Installed grub in the MBR on the 120 Gb partition for 10.10, it even recognised my 2 3ware pci raidcontroler on which 8.04 is installed.
When I start I get grub, when I choose for 10.10 I get a black screen with a cursor blinking in the left uppercorner. Luckily I can start into 8.04. I have no idea how to continu. for now I will burn a knoppix cd so I can read the ext4 partition with 10.10 and hope to find something to solve this.
View 6 Replies
View Related
Nov 28, 2008
I'm a fairly new linux user and I seem to have a problem with ubuntu 8.10 after installing it.To make sure everything was working fine before i could do a dual installation, i ran the live cd and it worked like a charm.Everything works fine in the live cd....the internet, sound, graphic drivers (even the special effects seemed to be work fine)I thought wow...after having a bitter experience with Ubuntu 8.04 and 7.10 (I couldnt install those at all coz of driver issues and stuff) I thought this is it!So I used the wubi installer to install ubuntu in my D drive (I didnt wanna use C just to be safe as the primary OS is installed there). Gave it a healthy space of 15 gb. Finished the installation and the rebooted.I went inside Ubuntu which started doing its installation and copying of files and stuff. So far so good.....
And then once it finished its installation and copying of files (100 %), the screen went blank and i see a cursor blinking. I thought maybe its restarting and thats why it must be doing this.I wait for nearly 10 mins and nothings happening except for the cursor blinking on the black screen. I press the caps lock key to see if anything is processing. Nope. So i manually shut it down and then load ubuntu.It loads like 20-30%....rests for a while....and then it loads a bit (not completley)....after that it takes me to a command line asking me for my password and username.I enter those correctly. But it doesnt get me into the main GUI screen yet.
It shows me a lot of the this error msg:
-bash: /dev/null:Permission denied
I'm still in command line (or terminal to be precise). So i use 'startx' (something which i learned from my csci labs ) to start a new session. It showed signs of starting a new session (i can see the mouse pointer and stuff) and then poof....back to the command line again.So I shut it down and load it again in recovery mode. It shows signs of the same symptoms in the splash screen (going very slow after 20-30 % ) and then this time, before i'm asked for my username and password in the command line, it shows a lot of warnings: fake daemon running (or something like that) and i cant even use startx!So i didnt know what to do, uninstalled ubuntu and did a fresh installation (wubi and in the same D drive). Reboot. Install and copy files 100% and then a blank screen again with the dreaded cursor blinking. I still wait for about 10 mins and nothing yet happens. So I manually shut it down (again) and then load ubuntu and unsurprisingly i have the same problem as what i described before....doesnt load properly and i'm not able to come out of the terminal.
View 2 Replies
View Related
Feb 5, 2010
I was going to set up an ubuntu server, but ran into some issues. When I try to install ubuntu server 9.10, it immediately goes to a black screen with a blinking cursor as soon as I press enter on the menu. I've tried pressing F6 and editing options - noapic, nolapic, irqpoll, vga=[something...] and nothing worked. I then downloaded a standard ubuntu desktop cd, and the livecd works, and I can successfully start the install!
I've heard that I should probably use the server install if I want to use this as a server (which I do; webserver for a group of people, website, ftp, ssh.) I've also heard that it's possible to just install everything needed overtop of an ubuntu desktop base. What should I do? Are there other things I should try to make the server install work? Or is it not worth the effort, and I should just go with a desktop install and then work from there? tasksel? (It's a Dell XPS, the graphics card is NVIDIA Geforce 9800 GT).
View 1 Replies
View Related
Aug 9, 2011
After installing Fedora 15 from LiveUSB and rebooting it just hangs on a black screen with a blinking cursor (underscore) in the top left of the screen. If it's reached grub, it isn't responding to any commands, and mashing several key combinations (such as ctrl-alt-f1) will produce a beep usually emitted only by the BIOS (hinting that it may never be making its way to grub).
The only particularly interesting thing about the install is that by default it wanted to boot itself from the MBR on my primary-master (Windows) disk. Instead I selected the option to boot from "the first partition in sdb1", which is my primary-slave (Linux) disk, (the first partition being /boot). This way I can change which OS boots by changing the boot order in my BIOS, and so avoiding bootloader wars.
View 5 Replies
View Related
Nov 29, 2009
Although I managed fairly quickly to get 3D enabled on the GF 7600GS of my desktop, it took me longer to get 3D up on the GF 9650M GT of my Asus laptop M70Vn. Although I made extensive use of the numerous procedures outlined here, none of them worked and booting my laptop always ended up with me facing a jet-black screen and a completely inexpressive blinking white cursor. My solution was simple: I did not blacklist Nouveau and problems mysteriously disappeared.
View 2 Replies
View Related
Nov 10, 2010
Just did a fresh Ubuntu 10.10 (minimal) install on my Asus EEE PC 1001PX.Before the minimal install I had Ubuntu Netbook Edition 10.10 which worked flawlessly, now all I get is a black screen with a blinking cursor:for the amazing quality, but I guess it's better than nothing.ctrl+alt+Fx does nothing, ctrl+alt+del reboots the computer.Booting with the usb-stick that was used for the install takes me to the login...
View 3 Replies
View Related
May 5, 2010
A few weeks ago I installed Ubuntu 10.4 beta on a pc. I upgraded it to 10.4 RC and 10.4 final release. I think it was after upgrading to 10.4RC that I started having a problem during startup. Here is what happens:
I turn the pc on the bootstrap process occurres, then the grub screen comes up I let ubuntu boot. For a few seconds I get a black screen with a blinking cursor. The Ubuntu splash screen flashes on the screen for maybe a second or two. Then I'm dumped to the command prompt on TTY1.
At this point I can log in with a username and password type startx and I'm at the ubuntu desktop. If I log off I'm back at the command prompt on TTY1. If I press alt-ctrl-F7 at the command prompt this is what I see, these are the last four lines of text: init: ureadahead-other main process (742) terminated with status 4
[Code]...
View 4 Replies
View Related
Oct 25, 2010
just did a dual boot install on a brand new DEll T1500. The machine has win7 on it. I booted off the live CD and all looked well. Installation went well. When I reboot, I get grub, select the top linux option and then see a small black blinking cursor for a few seconds, then nothing. The screen reports no signal.
View 8 Replies
View Related
Jun 4, 2011
I built my computer and having trouble booting Ubuntu, here are my system specifications.
System Specifications:
CPU: AMD Athlon II X4 3.0GHz Quad-Core
GPU: ATI Radeon HD 5750 1GB 128-bit GDDR5
Motherboard: ASUS M4A88TD-V EVO/USB3
Memory: 4G G.SKILL Ripjaws DDR3 1600
PSU: Cooler Master GX Series 750w
HDD: 500GB Samsung 7200 RPM
I have Ubuntu on a DVD and have tried both my DVD drives, AND an external DVD drive and have no luck. I have tried different versions of Ubuntu and get the same problem. So I boot it fine and it gets the the Ubuntu splash screen and I select "Install Ubuntu" it loads for a few seconds then goes to a black screen with a blinking cursor in the top left corner. It sits here forever. I tested on my friends computer with very similar processor and it blinks for about 3 seconds then an Ubuntu splash screen appears with dots under it and it loads and works fine.
So I am 100% positive the DVD is fine and should work for my processor also. I do have Windows 7 currently installed. And I made a 100 GB partition via Windows 7 using Easeus Partition Manager. If it matters, I did test Ubuntu on my computer by installing it from VirtualBox and it worked fine...but I'd rather do a dualboot because I don't like running an OS in another OS and its performance isn't so great when emulating an Operating System...
View 9 Replies
View Related
Jul 11, 2011
I am using fedora 15 on my dell studio 1558 . Sometimes a black screen appears with a cursor blinking when i tries to reduce the brightness of the laptop and somethimes it automatically happens . And i am not able to do anything its just like the blue screen of death as in windows . the only way to get back is by restarting the computer
View 8 Replies
View Related
Jul 9, 2010
I have here two old identical compaq pc's with 64mb ram.I want to copy drive/os from one machine to other. So i do a drive to drive clone (witn both hd's deing connected to another machine). And it says its done and okay. But the second (cloned) machine doesnt boot. And have the black screen with the blinking white cursor in top left corner. I have already tried to do fdisk /mbr and also copying partition table from original to destination disk. Because i think it is logical that with a drive to drive clone it sould be copied. But i have a doubt in that somehow. Because why would it not boot if it was copied then
View 9 Replies
View Related
Jan 11, 2010
I am installing Fedora 12 on a VIA pico ITX and am running into some issues.
I had the same board but with an PATA/IDE drive, and on that it installed just fine. I needed a bigger/better drive so I did get an SATA drive for it.
After the install it either freezes/hangs when the post install begins or IF the post install works (when I use ide=nodma) it won't boot. I do get to see the grub screen (if I change the timeout in grub.conf) but as soon as the kernel starts loading it freezes. and I see a black screen with a prett fast blinking cursor.
With the live cd, if I try to boot: it reports, no root available going to sleep.
View 2 Replies
View Related
Jan 26, 2010
I have just installed slackware. I have done
Code:
Xorg -configure
And chosen kde for init program while installing slackware. But when I type
Code:
Xorg -config -retro
or
Code:
startx
I get black screen with blinking button on monitor and keyboard. Obviously KDE doesn't start.
View 14 Replies
View Related
Jan 5, 2010
I have a problem - after installation of Ubuntu 9.10 I discovered that I do not have virtual terminals on my computer. When I am trying to switch, to another virtual terminal with, say, Ctr-Alt-F2, I am getting a black screen with lonely cursor blinking in the upper left corner (no login prompt).my tty2.conf file is
Code:
# tty2 - getty
#
# This service maintains a getty on tty2 from the point the system is
# started until it is shut down again.
start on runlevel [23]
stop on runlevel [!23]
[Code]...
View 8 Replies
View Related
May 3, 2010
I dual-boot Windows 7 and Ubuntu. Sometime between 4/18 and a few days ago, something happened with Windows booting up. Ubuntu boots fine, but whenever I try to boot Windows, it just goes to a black screen with a blinking cursor (the command line kind, not a pointer). At first I thought it was Windows, but I have run the repair CD and executed chkdsk /f and chkdsk /r on all partition related to windows. No effect.
I ran a system check designed for issues with booting up, and it found no errors. I have looked at my GRUB files, and they all look fine. I am not sure if it is GRUB or Windows. I tried reinstalling the Windows boot-loader, and it had the same effect, the only difference is that it bypassed GRUB. The reason I think it may be GRUB is that the error happened around the same time as me upgrading from Karmic to the Lucid RC. I have posted this on a Windows 7 forum.
View 9 Replies
View Related
Oct 21, 2010
i did the upgrade thru the update manager but when i rebooted my comp, my computer didnt go pass the black screen with the bar blinking. what black screen im talking about
View 6 Replies
View Related
Oct 7, 2010
I installed Ubuntu on a Toshiba Satellite about a month ago. It worked for about three hours. I installed Wine, and it still worked but the display would sometimes go black for a few seconds. Later that day I rebooted and that was it, no more Ubuntu. It goes through all of the process of booting but then the screen just goes black before I even get to the purple Ubuntu screen. I'm running this on a drive in an enclosure so I simply plugged the drive into another machine ( actually two other machines ), and it works perfectly. I have an old Vista drive that I put in the Toshiba and that works just fine, so it's not a pure hardware issue. Just to be sure I wiped the Ubuntu drive and re-installed, this time without installing wine. No Toshiba love. Just the black screen. I even made a flash drive with the loader and iso from the Ubuntu site. Same deal. It starts to boot from the flash and then just goes black where you would normally expect the purple Ubuntu screen. This thing is driving me nuts and I am at a point where I really need this machine working and will be faced with simply wiping the Ubuntu drive and installing Windows.
View 9 Replies
View Related
Dec 14, 2009
I keep starting up Fedora and I'm not able to get far (although it's not always at the same time) before my screen will go black, except it shows the mouse/cursor - but it's frozen, and thhen the caps-lock light starts blinking and I can't do anything or get it to recover. Sometimes it happens after 30 seconds, sometimes 40+ seconds and sometimes within 15 or so seconds.
How do I stop this and diagnose this?
I've tried, in the boot-startup to choose an older kernel version, butt the same thing occurs!
I have:
Fedora 11
Kernel: 2.6.29.6-217.2.16.fc11 i586
Asus EEE PC 1002HA
One other thing, it does always seem to happen after I've turned on wireless. And I've been using F11 for months now with no issue.
View 3 Replies
View Related
Mar 8, 2011
I have a problem with booting from a USB flash drive. I have Acer TimelineX 3820TG. I have Windows 7 Home from Acer and I installed Mandriva OS from USB(from USB because this Acer doen't have a DVD drive). It was OK, but I want reinstall Windows 7 and so I did. Now I have Windows 7 Professional and it wrote over Mandriva's GRUB. It wasn't a big problem. For a while I was just using Windows 7 but now I am thinking that I need some OS with Linux and I am thinking about Ubuntu. But when I tried to boot from USB with Ubuntu I get a black screen with a blinking cursor after the BIOS POST.
I was trying many applications to create a bootable USB drive and many versions of Ubuntu (and other Linux distributions), but nothing worked. I tried to Google for answers but I found many problems where all booting goes to black screen but in my problem Windows 7 boots fine from disc but from USB doesn't work.
View 1 Replies
View Related
Oct 4, 2010
I had my system running fine on Debian for about a month and a half. Then tonight the display suddenly went black. The system was still running, but my screen was black (though the monitor didn't indicate that it had lost signal). I restarted the computer; it booted through the BIOS and showed me my GRUB menu, but then the display went black again. Shorting the jumper pins to clear CMOS data didn't help; in fact, that made the display go black even sooner. Now, I see my motherboard's BIOS splash screen for a couple of seconds, and the display goes black. I know the system is still booting okay, because I hear the usually noises from the internal speaker. But I now have no visual output.
Could this be an issue with the motherboard or the video card? The board doesn't have onboard video, or else I'd try that. And I don't have any spare boards, video cards, or monitors available to me here. I did try using a D-sub cable instead of DVI-D (my monitor and video card support both), but that was no better. What can I do to try to fix this problem?
Motherboard: MSI 870A-G54
CPU: AMD Athlon II X2 250 (at 3.0 GHz, not overclocked)
Video card: Sapphire 100252HDMI Radeon HD 4550
Monitor: Asus VW195T
View 3 Replies
View Related
Jul 1, 2010
I am trying to boot up Linux Mint 7 after a packages upgrade and it boots up but then it shows this and stalls.And similar messages for GDM and then it just shows a black screen with a single blinking cursor on the middle left of the screen. I cannot do anything except press the CTR-ALT-DEL combination to re-boot, then it shows the usual shutting down messages and does the re-boot.I am running the 2.6.28-19 kernel and I have upgraded the Ubuntu packages on my Linux Mint 7 system from Jaunty to Karmic. Please help as I do not want to re-install. I am running Knoppix 6.3 ATM and I should be able to chroot from that if necessary. I am booting from /sda1 that has Linux Mint 8 installed and grub 1.97.
View 1 Replies
View Related
Feb 21, 2010
On a Karmic desktop with a Radeon 2600 hd video card, my screen goes black for a couple of seconds when opening an avi (divx or mjpeg).The video starts playing immediatly but I only see a black screen. Using Movie Player, its a black screen window, using vlc or gmplayer or mplayer ,the all screen goes black. It does not happen if I use the ati open source driver (but then flash full screen crashes...). I just installed the latest ati catalyst (10.2) and the problem remains.....
View 1 Replies
View Related
Mar 11, 2010
I have an Acer Aspire One Netbook, and I have the Ubuntu 9.10 Netbook Remix installed. I have tried using Cheese to capture video and it captures maybe 2 seconds of movement, then goes black and/or the image freezes. I can take photos just fine, but video capture seems to be impossible. Any help?
View 2 Replies
View Related
Oct 30, 2009
I ran into a problem the moment i installed 11.1. The GUI wouldn't show up (ctrl+alt+f2 yeilded a black screen with a blinking underscore). Failsafe worked fine, though.
So, i tried entering, one by one, every parameter that was entered in the failsafe boot options. Entering 'x11failsafe' gave me a flawless GUI. So, i opened the '/boot/grub/menu.lst' file and added this parameter in the 'showopts' of the normal mode, to make it permanent. Fine. Now, what exactly have i done?
Note- I use an NVidia 8000 series Graphic card. I'll post more details if you need them.
View 4 Replies
View Related
Jan 17, 2010
I am trying to install 11.2 but it keeps freezing. I press install and the Linux kernal loads and afterwards I get a black screen and after 30 seconds the DVD player stops running. I have also tried to the online network install and the exact same thing happens. I also tried a DVD I have of 11.1 which I know is good since I have successfully installed it on other machines and the result is also the same. My computer currently has a dual boot of XP and Kubuntu 9.10.
I am returning to Suse after experimenting with Kubuntu but thought I would leave the Kubuntu on the machine (prefer Suse but Kubuntu installed very easily on my computer). Could the Kubuntu be causing this problem or is the difficulty something else? I have also tried the safe install and the other options to no success.
View 9 Replies
View Related
Oct 14, 2010
I've got two laptops running Ubuntu. Both have had Lucid installed from the live cd. I have upgraded one of them to Maverick. Both distributions are running great after they boot up, but I haven't experienced any faster boot times with either distibution. Both boot to Bios and then the screen goes black with a blinking cursor in upper left corner of the screen. The black screen remains for 30 to 45 seconds and then I get the Ubuntu splash screen for maybe 5 seconds, and then desktop. Why am I not seeing faster boot times? I realize 45 to 60 seconds is good compared to other os's, but I anticipated much faster boot times. Shut down on the other hand is quite fast at maybe 5 to 10 seconds. Does anyone else get this black screen on boot? Seems like wasted time cause I can't tell what's going on during the time there is a black screen. This is not a real big deal breaker, as I don't reboot very often, but I just wonder why bootup isn't faster.
View 7 Replies
View Related
Mar 7, 2010
I just got an update notice two hours ago and after updating I rebooted my machine to find that it no longer boots. The update was for 23 bug fixes for Nvidia drivers and Nvidia support software. I get a black screen with the message "serial8250: too much work for irq17" and a blinking cursor. How do I recover from this?
View 14 Replies
View Related
