Ubuntu :: Getting A Black Screen With Lonely Cursor Blinking In The Upper Left?
Jan 5, 2010
I have a problem - after installation of Ubuntu 9.10 I discovered that I do not have virtual terminals on my computer. When I am trying to switch, to another virtual terminal with, say, Ctr-Alt-F2, I am getting a black screen with lonely cursor blinking in the upper left corner (no login prompt).my tty2.conf file is
Code:
# tty2 - getty
#
# This service maintains a getty on tty2 from the point the system is
# started until it is shut down again.
start on runlevel [23]
stop on runlevel [!23]
I have here two old identical compaq pc's with 64mb ram.I want to copy drive/os from one machine to other. So i do a drive to drive clone (witn both hd's deing connected to another machine). And it says its done and okay. But the second (cloned) machine doesnt boot. And have the black screen with the blinking white cursor in top left corner. I have already tried to do fdisk /mbr and also copying partition table from original to destination disk. Because i think it is logical that with a drive to drive clone it sould be copied. But i have a doubt in that somehow. Because why would it not boot if it was copied then
I have rebuild my system, with an Asus motherboard M4A88TD-V EVO/USB3 with radeon 4250 integrated 8 Gb memory Athlon II 4x 640 2 x 1 TB sata3 WD Harddisks I installed 10.10 64bit, and ran through the whole install with the alternate CD without problems, Installed grub in the MBR on the 120 Gb partition for 10.10, it even recognised my 2 3ware pci raidcontroler on which 8.04 is installed.
When I start I get grub, when I choose for 10.10 I get a black screen with a cursor blinking in the left uppercorner. Luckily I can start into 8.04. I have no idea how to continu. for now I will burn a knoppix cd so I can read the ext4 partition with 10.10 and hope to find something to solve this.
I set my drives up with MY boot loader, and I boot several OSes.I installed Ubuntu and told it to place grub on the / drive, which is where I always put it with any other install and it works fine.I find now that despite telling the install where to put it, you guys have taken it upon yourselves to alter the MBR of the volume ANYWAY!
SO, what I need to do is re-install grub, but I see that you also have no repair facility on this disc either. All I want to do is use MY boot loader. Currently, when I point at the / volume it just hangs with a non-blinking cursor in the upper left.No other Linux installs I have performed over the years do this. I want the drive to boot by merely pointing my bootloader at that volume.It always has in the past, so what did you guys change? I want NO action on my MBR, but I DO want a working grub on the actual root volume, which is NOT the first volume on the drive.
I have a Windows XP Dell laptop that completely froze the other day. I cannot start it up, and cannot even access safe mode -- it just goes to black screen with underscore in the upper left corner.
So, I did some searching and saw a recommendation to create a Ubuntu Live CD to run and access the info on the hard drive, at least. I have most of it backed up, but not the drivers and I know that will be a pain to redo. So, I am mostly hoping at this point to recover a little info off the drive before reinstalling the OS. Of course, if I could just fix it, that would be better...
I get an error message when I try to access the hard drive through Ubuntu that says it is in hibernation mode and I need to start windows and shut it down properly before Ubuntu can mount the drive. Since I can't get into Windows, this is impossible. It also said something about being able to mount it read-only.
Just did a fresh Ubuntu 10.10 (minimal) install on my Asus EEE PC 1001PX.Before the minimal install I had Ubuntu Netbook Edition 10.10 which worked flawlessly, now all I get is a black screen with a blinking cursor:for the amazing quality, but I guess it's better than nothing.ctrl+alt+Fx does nothing, ctrl+alt+del reboots the computer.Booting with the usb-stick that was used for the install takes me to the login...
A few weeks ago I installed Ubuntu 10.4 beta on a pc. I upgraded it to 10.4 RC and 10.4 final release. I think it was after upgrading to 10.4RC that I started having a problem during startup. Here is what happens: I turn the pc on the bootstrap process occurres, then the grub screen comes up I let ubuntu boot. For a few seconds I get a black screen with a blinking cursor. The Ubuntu splash screen flashes on the screen for maybe a second or two. Then I'm dumped to the command prompt on TTY1.
At this point I can log in with a username and password type startx and I'm at the ubuntu desktop. If I log off I'm back at the command prompt on TTY1. If I press alt-ctrl-F7 at the command prompt this is what I see, these are the last four lines of text: init: ureadahead-other main process (742) terminated with status 4
just did a dual boot install on a brand new DEll T1500. The machine has win7 on it. I booted off the live CD and all looked well. Installation went well. When I reboot, I get grub, select the top linux option and then see a small black blinking cursor for a few seconds, then nothing. The screen reports no signal.
I am using fedora 15 on my dell studio 1558 . Sometimes a black screen appears with a cursor blinking when i tries to reduce the brightness of the laptop and somethimes it automatically happens . And i am not able to do anything its just like the blue screen of death as in windows . the only way to get back is by restarting the computer
i thought i would give ubuntu 10.04 a try. So i downloaded the iso twice from two differant sources and burned to 2 diff dvd with diff burners and get the same problem. When i boot off of the disk i get the menu but whether i choose install are run live cd it just sits there for a sec are 2 then goes to black screen with flashing white bar in upper left hand corner and thats all it does. even tried my 9.10 disc which i know works. but it does the exact same. I have purchased a new video card since i last ran ubuntu and its the nvidia gtx 260 core 216. would that be whats causing my problems?
I am installing Fedora 12 on a VIA pico ITX and am running into some issues.
I had the same board but with an PATA/IDE drive, and on that it installed just fine. I needed a bigger/better drive so I did get an SATA drive for it.
After the install it either freezes/hangs when the post install begins or IF the post install works (when I use ide=nodma) it won't boot. I do get to see the grub screen (if I change the timeout in grub.conf) but as soon as the kernel starts loading it freezes. and I see a black screen with a prett fast blinking cursor.
With the live cd, if I try to boot: it reports, no root available going to sleep.
I am having trouble with the grub boot menu. I have a dual boot system, Windows XP 32 bit and Ubuntu 10.04 64 bit. Windows was preexisting when I installed Ubuntu. The install went fine but when I restarted, the Grub menu gives the option of the Windows boot loader but when I tab to that and press enter the screen goes black and the curser just blinks in the upper left corner...no XP boot. The XP drive is there as I can mount it from Ubuntu side but when I try to boot into it it does not seem to be there. What have I done and what can be done so that I can boot into the XP side?
I dual-boot Windows 7 and Ubuntu. Sometime between 4/18 and a few days ago, something happened with Windows booting up. Ubuntu boots fine, but whenever I try to boot Windows, it just goes to a black screen with a blinking cursor (the command line kind, not a pointer). At first I thought it was Windows, but I have run the repair CD and executed chkdsk /f and chkdsk /r on all partition related to windows. No effect.
I ran a system check designed for issues with booting up, and it found no errors. I have looked at my GRUB files, and they all look fine. I am not sure if it is GRUB or Windows. I tried reinstalling the Windows boot-loader, and it had the same effect, the only difference is that it bypassed GRUB. The reason I think it may be GRUB is that the error happened around the same time as me upgrading from Karmic to the Lucid RC. I have posted this on a Windows 7 forum.
I have an Acer Aspire One AOA110 that came with Windows XP.
I created a usb flash drive install for Ubuntu 10.10 netbook edition and went through the install process (wiped disk clean, not a dual boot with WINXP).
Before install, I was able to run Ubunut from the usb key with no problems.
At the end of the install, it told me I needed to restart, so I clicked the "restart" button and the removed the usb drive. Nothing happened and it never restarted and just completley hung for about 20 minutes. I manually shut down the computer by holding the power for 10 seconds and then rebooted the machine. Now all I get after the "acer bios" screen is a black screen with a blinking cursor. If I press any buttons, the computer beeps at me.
I'm a fairly new linux user and I seem to have a problem with ubuntu 8.10 after installing it.To make sure everything was working fine before i could do a dual installation, i ran the live cd and it worked like a charm.Everything works fine in the live cd....the internet, sound, graphic drivers (even the special effects seemed to be work fine)I thought wow...after having a bitter experience with Ubuntu 8.04 and 7.10 (I couldnt install those at all coz of driver issues and stuff) I thought this is it!So I used the wubi installer to install ubuntu in my D drive (I didnt wanna use C just to be safe as the primary OS is installed there). Gave it a healthy space of 15 gb. Finished the installation and the rebooted.I went inside Ubuntu which started doing its installation and copying of files and stuff. So far so good.....
And then once it finished its installation and copying of files (100 %), the screen went blank and i see a cursor blinking. I thought maybe its restarting and thats why it must be doing this.I wait for nearly 10 mins and nothings happening except for the cursor blinking on the black screen. I press the caps lock key to see if anything is processing. Nope. So i manually shut it down and then load ubuntu.It loads like 20-30%....rests for a while....and then it loads a bit (not completley)....after that it takes me to a command line asking me for my password and username.I enter those correctly. But it doesnt get me into the main GUI screen yet.
It shows me a lot of the this error msg: -bash: /dev/null:Permission denied
I'm still in command line (or terminal to be precise). So i use 'startx' (something which i learned from my csci labs ) to start a new session. It showed signs of starting a new session (i can see the mouse pointer and stuff) and then poof....back to the command line again.So I shut it down and load it again in recovery mode. It shows signs of the same symptoms in the splash screen (going very slow after 20-30 % ) and then this time, before i'm asked for my username and password in the command line, it shows a lot of warnings: fake daemon running (or something like that) and i cant even use startx!So i didnt know what to do, uninstalled ubuntu and did a fresh installation (wubi and in the same D drive). Reboot. Install and copy files 100% and then a blank screen again with the dreaded cursor blinking. I still wait for about 10 mins and nothing yet happens. So I manually shut it down (again) and then load ubuntu and unsurprisingly i have the same problem as what i described before....doesnt load properly and i'm not able to come out of the terminal.
I was going to set up an ubuntu server, but ran into some issues. When I try to install ubuntu server 9.10, it immediately goes to a black screen with a blinking cursor as soon as I press enter on the menu. I've tried pressing F6 and editing options - noapic, nolapic, irqpoll, vga=[something...] and nothing worked. I then downloaded a standard ubuntu desktop cd, and the livecd works, and I can successfully start the install!
I've heard that I should probably use the server install if I want to use this as a server (which I do; webserver for a group of people, website, ftp, ssh.) I've also heard that it's possible to just install everything needed overtop of an ubuntu desktop base. What should I do? Are there other things I should try to make the server install work? Or is it not worth the effort, and I should just go with a desktop install and then work from there? tasksel? (It's a Dell XPS, the graphics card is NVIDIA Geforce 9800 GT).
I have a problem with booting from a USB flash drive. I have Acer TimelineX 3820TG. I have Windows 7 Home from Acer and I installed Mandriva OS from USB(from USB because this Acer doen't have a DVD drive). It was OK, but I want reinstall Windows 7 and so I did. Now I have Windows 7 Professional and it wrote over Mandriva's GRUB. It wasn't a big problem. For a while I was just using Windows 7 but now I am thinking that I need some OS with Linux and I am thinking about Ubuntu. But when I tried to boot from USB with Ubuntu I get a black screen with a blinking cursor after the BIOS POST.
I was trying many applications to create a bootable USB drive and many versions of Ubuntu (and other Linux distributions), but nothing worked. I tried to Google for answers but I found many problems where all booting goes to black screen but in my problem Windows 7 boots fine from disc but from USB doesn't work.
I am trying to boot up Linux Mint 7 after a packages upgrade and it boots up but then it shows this and stalls.And similar messages for GDM and then it just shows a black screen with a single blinking cursor on the middle left of the screen. I cannot do anything except press the CTR-ALT-DEL combination to re-boot, then it shows the usual shutting down messages and does the re-boot.I am running the 2.6.28-19 kernel and I have upgraded the Ubuntu packages on my Linux Mint 7 system from Jaunty to Karmic. Please help as I do not want to re-install. I am running Knoppix 6.3 ATM and I should be able to chroot from that if necessary. I am booting from /sda1 that has Linux Mint 8 installed and grub 1.97.
After installing Fedora 15 from LiveUSB and rebooting it just hangs on a black screen with a blinking cursor (underscore) in the top left of the screen. If it's reached grub, it isn't responding to any commands, and mashing several key combinations (such as ctrl-alt-f1) will produce a beep usually emitted only by the BIOS (hinting that it may never be making its way to grub).
The only particularly interesting thing about the install is that by default it wanted to boot itself from the MBR on my primary-master (Windows) disk. Instead I selected the option to boot from "the first partition in sdb1", which is my primary-slave (Linux) disk, (the first partition being /boot). This way I can change which OS boots by changing the boot order in my BIOS, and so avoiding bootloader wars.
Although I managed fairly quickly to get 3D enabled on the GF 7600GS of my desktop, it took me longer to get 3D up on the GF 9650M GT of my Asus laptop M70Vn. Although I made extensive use of the numerous procedures outlined here, none of them worked and booting my laptop always ended up with me facing a jet-black screen and a completely inexpressive blinking white cursor. My solution was simple: I did not blacklist Nouveau and problems mysteriously disappeared.
This issue was solved On June 9th. Root cause was Kore 2 controller device being misinterpreted as a pointing device. I hope to eventually use the Kore as a straight-up MIDI controller in Ubuntu Studio, but that's a long way off. For now I will unplug it whenever I boot Ubuntu Studio. XINPUT LIST gave me the hint I needed to figure this out. Original post and problem resolution thread follows:
I'm a total Linux newbie, but well versed in Windows. Just installed Ubuntu Studio 10.10. This was a clean install, not an upgrade.. Installation went fine, but when I boot into it, I get the cursor stuck at the upper left corner of the screen. When I move the mouse, the cursor will move, but it immediately jumps back to the upper left corner. I can't select anything except to open the main menu. Then I must use keyboard cursor control to navigate.
I finally got around to installing Fedora 15 on my HTPC. I noticed that the mouse cursor starts in the upper left corner of the screen as soon as the login screen appears. This means that after login, if I only used the keyboard so far, the Gnome Shell overlay starts immediately.This is at most an interesting quirk until I try to set XMBC to automatically launch. Now I have to press <Esc> or move the mouse to de-activate the overlay before I can use the program.Is this mouse cursor thing intended behaviour, is there some software fix, or is it a hardware quirk? I have a Radeon HD 4650 graphics card (Smolt profile).
I'm running an Acer 1810Tz, dual boot with win7.Under 9.10 and Grub I had no boot issues, however I have just completed the upgrade to 10.04 and upgraded GRUB to GRUB2.Everything boots just fine into Ubuntu, and my GRUB menu looks right, but when I select the Windows 7 option, the machine just hangs with a black screen, white cursor top left. I'm sure this is a trivial problem, something overwritten that shouldn't have been perhaps, but I have no clue where to start.
Problem-PC automatically boots into a black screen with blinking cursor. No message or nothing
I have 4 HD. Primary drive has Windows Vista, Secondary no OS installed. Sata1 HD Ubuntu 10.04, Sata2 Windows 7. Prior to installing windows 7 all was perfect but once I did it, grub got all screwed up. The only way I can boot into grub is if I manually select my Sata1 which has Ubuntu on it and only then it allows me to select Linux or Windows OS. How can I change that so it can boot up normally as before? I'm assuming that grub was installed in the primary drive which has vista on it, but once I installed windows 7 it got deleted and when I tried reinstalling Ubuntu, the grub was not installed in the primary drive.
I've got two laptops running Ubuntu. Both have had Lucid installed from the live cd. I have upgraded one of them to Maverick. Both distributions are running great after they boot up, but I haven't experienced any faster boot times with either distibution. Both boot to Bios and then the screen goes black with a blinking cursor in upper left corner of the screen. The black screen remains for 30 to 45 seconds and then I get the Ubuntu splash screen for maybe 5 seconds, and then desktop. Why am I not seeing faster boot times? I realize 45 to 60 seconds is good compared to other os's, but I anticipated much faster boot times. Shut down on the other hand is quite fast at maybe 5 to 10 seconds. Does anyone else get this black screen on boot? Seems like wasted time cause I can't tell what's going on during the time there is a black screen. This is not a real big deal breaker, as I don't reboot very often, but I just wonder why bootup isn't faster.
I just got an update notice two hours ago and after updating I rebooted my machine to find that it no longer boots. The update was for 23 bug fixes for Nvidia drivers and Nvidia support software. I get a black screen with the message "serial8250: too much work for irq17" and a blinking cursor. How do I recover from this?
What does it mean if you boot from a live CD, the CD spins, a screen appears with the keyboard and human icons at the bottom, then a blank screen appears with a blinking cursor in the upper left corner - and that's it? It just stays that way.
I've tried two different discs, one 10.04 and one 10.10; and two different disc drives.
I have Windows XP, Vista and Ubuntu (10.04) all installed on my single hard drive. I re-installed XP and then ran the Vista CD to repair the Vista bootloader so that I could boot into XP and Vista. I can't figure out how to boot into Ubuntu now. I tried using EasyBCD (I believe an older version, maybe 1.72) to add Ubuntu to the Vista bootloader but I didn't have any luck. Ubuntu is in the menu, but when I select it, it goes to a screen that has GRUB in the upper left corner and does not load Ubuntu.
If it helps, before I re-installed XP and re-installed the Vista bootloader I was using GRUB for XP, Vista and Ubuntu because Ubuntu was the last thing to get installed.Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot InfoSummary:===============================> Windows is installed in the MBR of /dev/sdasda1: _________________________________________________________________________File system: ntfsBoot sector type: Windows Vista/7B
I recently installed Kubuntu 10.04 on a Toshiba Satellite 5205 laptop (which is prone to overheating, if it helps - it was on a platform in the back for airflow, though), which worked great for about 4 days.
Recently, I picked it up (looking for a USB port) and rotated it around a little bit. However, after this, the screen was darkened (not fully), and I could move the mouse for about half a second, after which it jumps back to the upper left corner of the screen. Rebooting doesn't help.
When it launches, sometimes a few mins later, the upper left of the screen (where gnome-terminal sits) freezes and becomes unresponsive. The cursor always stays as the 'text entry' cursor when in the region. If I alt-drag the window and close, nothing changes.It only goes away when I right click the area (even if I have moved/closed the terminal window) I have terminal options so I select 'close' then the screen resumes.
