Ubuntu :: How To Get A RAID-1 Back
May 27, 2010
I had a working RAID-1 (software raid) under 9.10 and the update to 10.04 failed totally. Now I did a new installation of 9.10 and wanted to have my RAID-1 back ... but how can that be done ?
The first partition has the ID "83", the second one "fd". I was able to create a degraded RAID and was able to get a backup from the "83" disc - but whatever I do with the second disc: its busy and nothing can be done with that.
My question: how can I build the original RAID-1 from these two discs using mdadm ? Actually I've read the documentation, but the documentation also says, that both partitions should have the "fd" ID.
View 1 Replies
ADVERTISEMENT
Sep 2, 2009
I am trying to prepare my PowerEdge 2950 before CentOS 5.3 installation(web server). I have hardware RAID 1/10 so I will have 2 virtual disks(VD).
First VDRAID 1) - 2 physical disks
Second VDRAID 10) - 4 physical disks
What should be write policy for the VD(RAID 1) and for the VD(RAID 10)? I would have "/var" and maybe "/tmp" on RAID 10.
View 1 Replies
View Related
Nov 2, 2010
I have a problem with a few up-to-date installations of CentOS 5.5. I have lost all md (software raid) devices on them some point in the past. They were working ok.
Now the 2 disks are seen as two separate disks, with no link between them.
# cat /proc/mdstat
Personalities :
unused devices: <none>
View 12 Replies
View Related
Mar 11, 2011
I have a 4 disk raid 5 array on my Ubuntu 10.10 box. They are /dev/sd[c,d,e,f].Smartctl started notifying me that /dev/sde had some bad sectors and the number of errors was increasing each day. To mitigate this I decided to buy a new drive and replace it.I have an external 4-bay disk enclosure. I failed /dev/sde via mdadm:
Code:
mdadm --manage /dev/md0 --fail /dev/sde
mdadm --manage /dev/md0 --remove /dev/sde
[code]...
View 5 Replies
View Related
Feb 1, 2011
Could any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
View 4 Replies
View Related
Jul 18, 2011
I have a raid5 on 10 disk, 750gb and it have worked fine with grub for a long time with ubuntu 10.04 lts. A couple of days ago I added a disk to the raid, growd it and then resized it.. BUT, I started the resize-process on a terminal on another computer, and after some time my girlfriend powered down that computer!
So the resize process cancelled in the middle and i couldn't acess any of the HDDs so I rebooted the server.
Now the problem, the system is not booting up, simple black with a blinking line. Used a rescue CD to boot it up, finised the resize-process and the raid seems to be working fine so I tried to boot normal again. Same problem. Rescue cd, updated grub, got several errors: error: unsupported RAID version: 0.91. I have tried to purge grub, grub-pc, grub commmon, removed /boot/grub and installed grub again. Same problem.
I have tried to erased mbr (# dd if=/dev/null of=/dev/sdX bs=446 count=1) on sda (ide disk, system), sdb (sata, new raid disk). Same problem. Removed and reinstalled ubuntu 11.04 and is now getting error: no such device: (hdd id). Again tried to reinstall grub on both sda and sdb, no luck. update-grub is still generating error about raid id 0.91 and is back on a blinking line on normal boot. When you'r resizeing a raid MDADM changed the ID from 0.90 to 0.91 to prevent something that happend happened. But since I have completed the resize-process MDADM have indeed changed the ID back to 0.90 on all disks.
I have also tried to follow a howto on a similar problem with a patch on [URL] But I cant compile, various error about dpkg. So my problem is, I cant get grub to work. It just gives me a blinking line and unsupported RAID version: 0.91.
View 2 Replies
View Related
Jun 29, 2011
migrate an installed Ubuntu system from a software raid to a hardware raid on the same machine? how would you go about doing so?
View 1 Replies
View Related
Nov 26, 2010
I have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
View 6 Replies
View Related
Mar 22, 2011
How long does hardware Raid card (raid 1, 2 drives)take to mirror a 1 TB drive (500gb used)?Is there a general rule of thumb for this?4 hours? 12 hours? 24 hours?
View 1 Replies
View Related
Aug 3, 2010
I am trying to connect a RAID Box to the server via LSI 8880EM2 RAID controller.The raid box is FUjitsu Externus DX60 with raid 1 configured.The server is Fujitsu Primergy SX300 S5 with LSI 8880EM2 RAID card.The external raid box is being recognised by the raid controllers bios.
The server runs CentOS 5.5 64bit. I have installed the megaraid_sas driver from LSI website and MegaCLI utility but CentOS still fails to see the box.MegaCLI utility, when launched from CentOS, recognises the raid box, CentOS does not(no mapping being created in /dev).
I have also tried to create a logical RAID0 HDD on one physical HDD(as seen by MegaCLI) with MegaCLI utility in CentOS.The result was success and the new logical drive could have been used, but when restarting the server, the controllers' bios fails with an error (not surprised(one logical RAID0 on one physical HDD)) and configuration is being erased.
Has anyone tried connecting 8880EM2 controller to a raid box with raid configured on the box, running it all under CentOS and what were the results.
View 3 Replies
View Related
Jun 12, 2010
I have two 1TB hard drives in a RAID 1 (mirroring) array. I would like to add a third 1TB drive and create a RAID 5 with the 3 drives for a 2TB system. I have ubuntu installed on a separate drive. Is it possible to convert my RAID 1 system to a RAID 5 without losing the data? Is there a better solution?
View 1 Replies
View Related
Jul 18, 2009
how can I create RAID 1+0 using two drives (one is with data and second one is new). Is it possible to synchronize data drive with empty drive and create RAID 1+0 ?
View 3 Replies
View Related
May 7, 2010
10.04
I managed to delete the Volume Applet that appears by default on the task bar. I'm sure it used to be listed in 'Add to Panel' in other version of Ubuntu however I can't see it there in 10.04.
Can someone explain to me how I get it back?
View 4 Replies
View Related
Feb 28, 2011
If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies
View Related
Dec 10, 2009
I am going to be using CentOs 5.4 for a home storage server. It will be RAID6 on 6 x 1TB drives. I plan on using an external enclosure which is connected via two SFF-8088 cables (4 drives a piece). I am looking to try and find a non-RAID HBA which would support this external enclosure and allow to use standard linux software raid.
If this is not an option, I'd consider using a hardware based raid card, but they are very expensive. The Adaptec 5085 is one option but is almost $800. If that is what I need for this thing to be solid then that is fine, I will spend the money but I am thinking that software raid may be the way to go.
View 3 Replies
View Related
Sep 15, 2010
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
View 4 Replies
View Related
Sep 1, 2011
i have noticed that if vista is not the active partition, hybernate does not work. it just goes black and then back to the user icon screen to log back in. another "slight" problem was that i was not able to apply a service pack. after restoring vistas dominance i was able to install the pack. is there any other work arounds for hybernate? even though you might not be interested in cleaning up after microsoft.
View 1 Replies
View Related
May 17, 2010
it was possible to back up time machine back ups from a mac in ubuntu.
I use a mac at work and use time machine to back up to an external hard drive which i take home each day. I wish to back up the time machine back ups off the external hard drive each day to my computer at home just to be safe is this possible?
I have managed to open the hard drive and have enabled view hidden files so i can see all the files but i am unable to copy them due to permission errors
View 1 Replies
View Related
Jul 21, 2011
I am looking to convert a raid 1 server I have to raid 10. It is using software raid, currently I have 3 drives in raid 1. Is it possible to boot into centos rescue, stop the raid 1 array. Then create the raid 10 with 4 drives, 3 of which still has the raid 1 metadata, will mdadm be able to figure it out and resync properly keeping my data? or is there a better way to do it?
View 2 Replies
View Related
Mar 24, 2011
I have a box that doesn't have a Raid controller or a software raid running currently. I would like to make it a RAID 1. Since it seems there isn't any IDE RAID controllers hardly around, I have another HD that is the exact model as the drive currently in the box running CentOS. Can I some how add the second drive and get the box to mirror from here own out? The box gets really hot and I want to be ready for a HD failure.
View 3 Replies
View Related
Jun 24, 2009
I've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
View 2 Replies
View Related
Dec 7, 2010
I'm working on a server and noticed that the to RAID5 setup is showing 4 Raid devices but only 3 Total devices. It's on a fully updated CentOS 5 system that only has three SATA drives, as it can not hold anymore. I've done some researching but am unable to remove the fourth device, which is listed as removed. The full output of `mdadm -D /dev/md2` can be see below. I've never run into this situation before.Anyone have any pointers on how I can reduced the Raid Devices from 4 to 3? I have tried
mdadm /dev/md2 -r failed
mdadm /dev/md2 -r detached
but neither work and since there is no block device listed I'm not quite sure how to get things back in sync so it's only seeing the three drives.
/dev/md2:
Version : 0.90
Creation Time : Tue May 25 11:07:04 2010
Raid Level : raid5
[code]....
View 8 Replies
View Related
Oct 24, 2010
I,m using Ubuntu 10.10 with Gimp. Ive got a lot of photos etc and need to back these up. Can I anyone suggest a good backup solution which does not require e to keep copying the same files? IE: Once the files are backed up I only want to back the files used since last back up?
View 11 Replies
View Related
Oct 19, 2010
Consider the following setup: Ubuntu system installed on a separate SSD for speed. An ubuntu software RAID array consisting of X number of physical HDD's for storage (RAID6 or RAID10). RAID setup is done during system install. If I suffer a total crash of the SSD and loose my system, will I be able to, using a new system disk, "reconnect" to the RAID array even if the "mothersystem" of the software RAID is lost? If yes, are there any particular config- or system files I need to backup to be able to rescue the array or will it just be recognized "out-of-the-box" when reinstalling ubuntu?
View 4 Replies
View Related
Apr 8, 2010
i have cretaed RAID on one of my server RAID health is ok but its shows warning. so what could be the problem. WARNING: 0:0:RAID-1:2 drives:153GB:Optimal Drives:2 (11528 Errors)
View 1 Replies
View Related
Aug 25, 2010
So I'm getting a new pc from my aunts husband and it has 2x 35GB disks with 10.000 rpm and another 250 gb (7.200 rpm).
I was thinking of putting it into a raid and run the 10.000rpm disks as the system, but I'm not too certain which one to pick. If I should take Raid 0 and have a 70 gb system drive or go for the security of a Raid 1, unless one of the two disks breaks. But that would only leave me with a 35 gb drive which seems a bit too low.
Should I run it as a 35 GB drive (Raid 1) and store all my software on the second disk instead (250 gb 7.200) and just use the system disk for..oh well, system. Instead of having my programs on the system drive as I've always had before.
View 3 Replies
View Related
Jan 6, 2010
Here is my system: I have dell poweredge 1950 PERC 6 with 300 GB raid system. It has two disks of each 300GB RAID mirrored system. I have few applications and data that reached around 280GB. As you know, poweredge 1950 we can have only two disk.
They are not mission critical. Hence, I wanted to remove the raid system and use as a non-raid system. By doing it, The applications and data can grow upto 600GB. I do not want to loose the data and setup. I am not so clear about RAID system and its conversion.
View 6 Replies
View Related
Oct 10, 2010
I can find many articles in google about migration from RAID 1 to RAID 5. But what about RAID 5 to RAID 1. I have a root(/) partition in RAID 1 and want to migrate to RAID 1. This is in production systems.
View 2 Replies
View Related
Oct 12, 2010
Recently while using a Highpoint 2310 (raid 5) I lost the mother board and CPU. I had to reinstall Centos and found it needed to initialize the array to function. Total loss of date. Question: If I use a true hardware card (3ware 9650se) and experience a serious hardware loss or the C drive can the card be installed with the drives on a new motherboard and function without data loss even if the OS must be reinstalled.
View 4 Replies
View Related
Mar 5, 2011
I recently installed language packs for Japanese and changed my system language to it, too. The problem is, now that I try to go back to English, the locale doesn't change back, only the menus are in english. "Apply system wide" in the Language Support didn't do anything; Firefox is in japanese too. Here is my locale output:
LANG=ja_JP.utf8
LANGUAGE=en_US:en
LC_CTYPE="ja_JP.utf8"
[code]....
View 1 Replies
View Related
