Ubuntu :: Higher Idle Temperature With Nouveau Drivers
Apr 29, 2010Is it just me or has anyone else noticed rise in idle temperatures with nouveau drivers vs proprietary drivers?
View 2 Replies
ADVERTISEMENT
Ubuntu :: Resolution Won't Go Higher Than 640x480 With Nvidia Drivers?
May 24, 2010I have a FX 5200 and a 26" TV with VGA input which supports 1330x760. No problem with this in Windows, but in Ubuntu, as soon as I install nvidia drivers (175) resolution goes 640x480.
I've tried editing xorg.conf in several different ways, but resolution didn't change, maybe I was doing it the wrong way.
PD: 10.04 Lucid Lynx fresh install
Fedora :: Switching Between Nvdia And Nouveau Drivers?
Jul 8, 2011I have Fedora 15 installed in my PC and I use it both for gaming and work. Now the open source nouveau driver was working fine, until I had to install the nvidia driver so that I could play torcs, as I was unable to get good graphics in nouveau. Now, when using the nvidia driver, the gnome shell has become too slow and sometimes unworkable, though games run good. Is there any way so that I can use both the drivers and switch between them when needed (say use nvidia when gaming and nouveau while at work) without uninstalling and reinstalling them?
PS: when I boot up, the grub shows two options, one is the fedora with latest kernel and other is the old kernel. Is there a possible way that I use nouveau with old kernel and nvidia in the new kernel? This will really help in switching games and work.
OpenSUSE :: How To Switch From Nouveau To NVidia Drivers
Aug 4, 2010After installing 11.3, I realised that my graphic driver is not working as desired. I have a Compaq CQ60-430SA laptop with an NVIDIA 8200M graphics card. Earlier with 11.2, I had some proprietary NVidia drivers and my graphics were smooth. However, I am not getting the same performance with Nouveau...
As can be seen from the screen clipping below, the images especially in the preview mode and the icons look jarred (highlighted in red). I have no complains with the video but the images and icons do look shabby at times and therefore I want to switch over to the proprietary NVidia drivers.
[URL]
Ubuntu :: Switch From Nvidia Drivers To Nouveau In Latest Kernal?
Mar 6, 2010Anyone knows the easiest way to switch from the nvidia drivers to teh nouveau drivers in the latest kernel?
View 2 Replies View RelatedOpenSUSE Hardware :: Unable To Find A Way To Configure Nouveau Drivers
Jul 16, 2010I had dual screen config (large desktop) going on 11.2 with proprietary nvidia driver without problems. After upgrade to 11.3 this didin't work. I was not able to find a way to configure nouveau drivers, and it was stuck in the 'twinview' mode, so decided to install binary nvidia instead (the 'hard way'). Took me a while to figure out 'nomodeset' thing, but in the end drivers were installed successfully. The problem now is that only monitor displays anything, and I can't find the nvidia control panel to activate second monitor and extend the desktop there.
Used to be able to install nvidia control panel easily in 11.2 with one-click install, but for 11.3 the page says that the one-click install buttons aren't ready yet (SDB:NVIDIA drivers - openSUSE) So my question is 'how to get dual screen going and extend my desktop to second screen using 11.3 and nvidia 210 card' ? And I don't care whether it's nouveau or proprietary drivers, as long as it's easy to configure and it works.
Debian :: Install Nvidia Drivers, But Installer Wrote To Disable Nouveau First?
Aug 8, 2010I've just installed Squeeze and try to install Nvidia drivers, but installer wrote that I have to disable Nouveau first. So could you please tell me how to turn off nouveau driver totally and correctly.
View 6 Replies View RelatedDebian Hardware :: GTX460 In Console - Nouveau And Nv Drivers From Xorg Not Working
Jan 27, 2011I am using Debian Squeeze, I have GPU Nvidia GTX460. I have tried almost everything, but I am not able to have working console after X starts. Nouveau and nv drivers from xorg are not working ( they dont support gtx460 ), so I am using nvidia drivers from [URL]... version 260.19.36. I am using kernel 2.6.32-5-686.
View 3 Replies View RelatedOpenSUSE Hardware :: Alteration In Fonts Looks After Change Of Graphic Drivers From Nouveau To NVIDIA?
Jan 8, 2011I recently changed my Graphic card drivers from Nouveau to nVIDIA in Suse 11.3 KDE.
One thing I have noticed that initially I had been using various Adobe Fonts in many applications prior to change of drivers. But after this change the looks of the same fonts became quite different, the length & breadth of "individual letters" changed quite a lot making them look not so beautiful as they were earlier. Am I missing something or is it a normal phenomenon. But I am satisfied with the present looks.
Fedora Installation :: Nouveau And NVidia Drivers - Jet-black Screen And A Completely Inexpressive Blinking White Cursor
Nov 29, 2009Although I managed fairly quickly to get 3D enabled on the GF 7600GS of my desktop, it took me longer to get 3D up on the GF 9650M GT of my Asus laptop M70Vn. Although I made extensive use of the numerous procedures outlined here, none of them worked and booting my laptop always ended up with me facing a jet-black screen and a completely inexpressive blinking white cursor. My solution was simple: I did not blacklist Nouveau and problems mysteriously disappeared.
View 2 Replies View RelatedGeneral :: CPUs Keep Toggling Between 100%idle And 0% Idle
Mar 22, 2011When I run top d 0.5 on my machine and I press 1 to enable the SMP View, I notice that all of the CPUs keep toggling between 100%idle and 0% idle.
The odd part is that when a CPU goes to 0.0% idle, I would expect to see one or more of the other columns peek, but they are not.
What is causing this?
Code:
Fedora :: Run Python3 Scripts From Command Line And Call Up Python 2.6.2 Idle With The Command Idle From Command Line?
May 29, 2010i've gotten my fedora 12 to the point where i can run python3 scripts from command line and can call up python 2.6.2 idle with the command 'idle' from command line. what command will call up python3 (3.1.2 to be exact) idle?
View 5 Replies View RelatedUbuntu :: Can't Monitor Cpu Temperature?
Jan 2, 2010I've recently installed Karmic on my new machine with the following specs;
Asus M4A785TD-V EVO Motherboard
AMD Athlon II X4 620 2.6GHz
Crucial 4GB (2x2GB) DDR3
Coolermaster Elite 330 Case
Western Digital WD5000AAKS 500GB
I'm looking to install some sort of temperature monitoring for my cpu and have had luck using either lm-sensors or acpi. With lm sensors, I've followed the various how to's on the forum and am still coming back with nothing. Trying to add hardware monitoring to panel brings up a 'no sensors found!' error, and x-sensors just starts up with a blank screen.
'sensors' in terminal spits back this -
Code:
lou@lou-quad:~$ sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
lou@lou-quad:~$
I've added the relevant lines into etc/modules as per the last question during configuration but still no joy. I've just run 'sensors-detect and had a gander at the output, and I'm wondering if its as simple as no one has written a driver for my mobo yet.
[Code]...
Ubuntu :: Getting CPU Temperature With MSI Board?
Oct 1, 2010So I just got a MSI 870A-G54 and have been trying to get the CPU temperature on the command line. I ran the following
Code:
sudo apt-get install lm-sensors hddtemp sensors-applet computertemp
And ran sensors-detect
Code:
sudo sensors-detect
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: MSI MS-7599
# Board: MSI 870A-G54 (MS-7599)
[Code].....
Ubuntu :: Check Out Temperature Of Cpu?
Sep 1, 2011So I would like to check out my cpu temperature in function of time. I've followed [URL]...gpu-en-ubuntu/ but unfortunately in the description it was for the old version of Ubuntu and despite having downloaded the program, I simply can't add it in the taskbar. I did in a terminal: sudo apt-get install sensors-applet. Then I installed a few remaining packets from synaptic. Now how do I run the program?
View 6 Replies View RelatedUbuntu :: 10.04 - 2 Cores CPU Temperature High
Apr 13, 2010I have a notebook with AMD Athlon 64 QL-62 2 cores CPU. Normally the temperature is 50-52 Celsius in idle but with Ubuntu 10.04 beta 2 idle temp is 60 Celsius. /proc/cpuinfo shows both cores on 1GHz which is good but still temp is higher than usual. I tried to find solution using Google but I didn't find anything.
View 1 Replies View RelatedUbuntu :: Temperature Too High Then Normal
May 3, 2010If I install Linux Mint 8 or Open Suse , temperature is 48 as windows mostly.If I install any other distro, temperature goes to 80-85 and fan is always On.Ive a laptop dell just bought it, dell studio 15, 4ghz ram dual core etc, a monster for linux but ive this problem, kinda annoying when you wanna have something silent and that doesnt become a furnace.
View 2 Replies View RelatedUbuntu :: How To Control At What Temperature The Fan Comes On And Shuts Off
May 20, 2010How to control at what temperature the fan comes on and shuts off. I am running Jaunty on a Compaq 610 laptop.
View 4 Replies View RelatedUbuntu :: LM Sensors - Cannot Find CPU Temperature
Dec 29, 2010I have tried lm-sensors and a few others, firefox just crashed.
Phenom II X6 1090T
MSI-890FXA-GD70 motherboard
Ubuntu 10.10
Senors:
k10temp-pci-00c3
Adapter: PCI adapter
temp1: +0.0C (high = +70.0C)
sensors-detect
Now follows a summary of the probes I have just done. Just press ENTER to continue:
Driver `k10temp' (autoloaded):
* Chip `AMD Family 10h thermal sensors' (confidence: 9)
No modules to load, skipping modules configuration.
Unloading i2c-dev... OK
There is a debugging panel on my motherboard, and I think that that displays the CPU temperature, although I am not sure.
General :: CPU Temperature When Installing Ubuntu?
Mar 12, 2010Trying to install Ubuntu from CD. I choose my language and hit Install and come to a black screen with the Ubuntu symbol glowing (loading everything I assume) and after a minute my screen fills up with messages saying my CPU Temperature is 99 (gets progressively higher) degrees. Is there something else I need to do before installing?
I have windows installed on my C drive and I'm planning on installing Linux on another blank drive. The Ubuntu version is the newest one (9.10) I think. I've got a Core i7, EVGA mobo, Nvidia 9600GT video card, and 6 gigs of memory. HDDs are all WD I believe, and the one I'm putting Linux on is 320 Gig.
Red Hat / Fedora :: Get Temperature Of CPU?
Jun 6, 2011In my system, the temperature of the CPU can be known from the file,/sys/bus/acpi/devices/LNXTHERM:00/ thermal_zone/temp . But I have found that not all systems have this file. Is there a generic method to get the temperature. Installing a package for this purpose won't be a solution as I'm building a simple gnome-shell extension. Something that comes along with the kernel would be perfect.
What could be other files that can possibly store temperature information, so that it would work on most atleast if not all? Any help like the file that stores temperature on your particular system only would also be highly appreciated.
Hardware :: VIA C7 CPU Temperature
Mar 5, 2011Does anybody know wich temperatures a VIA C7 processor can tolerate (max) ?
If i let the server run without the top: ~40C (104 Fahrenheit)
If i let the server run _with_ the top on: ~65C (149 Fahrenheit)
Someone over at silentpcreview.com suggests that the C7 can easely tolerate temperatures of 100C (212 Fahrenheit)
Ubuntu :: Laptop Automatically Shuts Down Because Of The CPU's Temperature
Jan 18, 2010For some reason,Ubuntu tends to use my CPU quite a lot.This cause my laptop to get really hot.Sometimes it even gets to the point when it automatically shuts down because of the CPU's temperature.Is there some sort of program or application to fix this?
View 5 Replies View RelatedUbuntu :: 10.04 Beta2 High Temperature And Internet
Apr 17, 2010I have installed the ubuntu 10.04 beta 2. I have notice that it has high temperature. I have try the "top" in terminal. There are no high usage of CPU and Memory. but still get high temperature. same in karmic 9.1. I have been using this ubuntu 10.04 beta2 fresh install just today. I did not do anything or install anything. It gets hot easily after few minutes. It was installed properly and no problem.
2nd problem is I try to reboot then i see the wifi signal and it detects my wifi and also my accesspoint. so I try to connect. I was connected to my accesspoint. My accesspoint is near my side. then I click firefox to test the connection. but no luck. cannot display page. maybe the internet was block even i was connected to my accesspoint. I try to check the signal then I saw (88%).
Ubuntu :: Landscape-sysinfo Not Displaying Temperature?
Jun 30, 2010I am running Lucid x64 on an Gigabyte Mobo with an Intel E6500 CPU.I think this script pulls the temperature from /proc/acpi/thermal_zone. However, that directory is empty.I can get the cpu temp by using lm-sensors or by running this:
Code:
cat /sys/class/hwmon/hwmon0/device/temp1_input
Any ideas on how to get landscape-sysinfo to display the temperature
Ubuntu :: Show CPU Temperature With Conky (AMD / K10Temp)
Oct 13, 2010I'm struggling to get my Conky feed to show the CPU temperature. I'm working with a fresh install of Ubuntu 10.10. Currently my Conky display shows a CPU temperature of 0 degrees Celsius, and I know this isn't true because I built the computer myself and I'm definitely not that good! Also, the GNOME hardware applet contradicts this and gives a more realistic CPU temperature of 33 degrees Celsius. What I can do to rectify this and get this displayed in my Conky?
The science bit:
I have done a sudo-sensors detect, and for CPU sensors it tells me:
Code:
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... Success!
(driver `k10temp')
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... No
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
The end summary is as follows:
Code:
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `k10temp' (autoloaded):
* Chip `AMD Family 10h thermal sensors' (confidence: 9)
and here is the relevant snippet of my conkymain file:
Code:
${color purple}CPU ${hr 4}$color
${freq}MHz Load: ${loadavg} Temp: ${acpitemp}
$cpubar
${cpugraph 000000 ffffff}
Ubuntu :: Temperature Monitor And Fan Controller Program?
Feb 2, 2011I installed ubuntu for the first time tonight and to put it simply everything is very confusing. I have been looking at different forums and everyone is installing programs in code and tbh i have no idea how to and i was wondering is there a program available that lets me monitor my CPU temp & alter fan speeds?
View 4 Replies View RelatedUbuntu :: Ultra High CPU Temperature On Natty?
Apr 28, 2011Well, today I've installed 11.04 on my laptop. Fresh install.I'm getting the following temps (idle)
Code:
Adapter: Virtual device
temp1: +64.0�C (crit = +126.0�C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +81.0�C (high = +100.0�C, crit = +100.0�C)
[Code]...
Ubuntu :: NTLDR Is Missing - Critical Temperature ?
Jul 11, 2011I recently installed Ubuntu and wanted to remove the Windows XP installation is was dual booted with (I used Wubi to install Ubuntu), but I ended up just editing boot.ini to remove it from the boot menu and automatically boot in to Ubuntu. But then, Ubuntu started playing up and keeps on popping up with the Critical Temperature warning, saying it's 80-100C although it's the first time it's been turned on in 14 hours... But to add to my confusion, when I try to boot from ANY disk, it comes up with "NTLDR is missing" and a restart message.
View 2 Replies View RelatedOpenSUSE :: HDD Temperature Control?
Mar 29, 2010There is a question, i'd like to ask: is there any decent program to monitor HDD temperature for linux? WHy are they so few? Suse Install repositories do not show any that could be installed. I used to use hddtemp on my previous 11.2 gnome installation, but it seems now something gone wrong, and i cant get this program anymore through: "sudo apt-get install hddtemp" and receive "sudo: apt-get: command not found", so as i am a newbie i can barely guess what is wrong. maybe there are any other programs to get this thing running. Its really puzzling because every laptop user need such tool badly, and i do not understand why is there so many monitor tools for cpu temperature and not a single good for hard drive which is far more important than cpu temperature, that rises and drops constantly as soon as your fans are fine???
View 2 Replies View Related