I'm using fluxbox on my eee pc 1000h and use conky to display % battery charge but (unlike my previous laptop) I don't get a hardware-triggered beep warning me of low battery.I've done a bit of searching but haven't yet found a neat software solution for either a beep or toolbar notification. Any suggestions?(I'm not wanting to switch back to KDE right now.)
View 4 RepliesI've been tooling around with Fedora with the Fluxbox environment on my old Dell 400SD4 laptop and it works fantastic. I'm still getting a feel for the environment, but one major concern that I had was a battery meter. Being a laptop, it's important to know when I'm almost out of juice. Does anyone have any suggestions for a battery meter for Fluxbox? Preferably one that can be installed through the yum repositories?
View 6 Replies View RelatedI don't know whats changed but since I installed 13.37 the fonts in fluxbox are crappy looking.Is there anything I should know thats changed with regards to this.They were fine in 13.1.
View 2 Replies View RelatedI would like to setup Fluxbox for a non-English, in this case German, environment. But I'd like to have the command line in terminal windows in English. With my attempts so far, either everything including command line error messages is in German, or nothing. Can anyone of you, please, provide a hint, what's the best way to solve this?
View 5 Replies View RelatedSo with 13.0 I compiled the fluxter pager and it come back with 'unable to connect to server' when bringing up fluxbox...I noticed that in KDE there is a nice pager that after some playing fits quite well into an enlarged taskbar, and began to set up my application to remember where it is in the pager, and the size/position of windows...Now, I have it set so that only minimised windows show as icons in the remainder of the taskbar, but I have noticed when I start up my app that all the windows show as minimised even though they are not.... when I click through each page of the panner they begin to dissapear and eventually I am just left with a couple that once I click them (even though there already maximised) they dissapear and I am left with a clean taskbar..
After this minising the window works as it should.The process I have spawns new processes, generally one in each pager window, and each process spawns multiple windows within that page window, so I have a lot of minimised stuff to go through!This is compounded by the fact that I have selected to only show minimised windows from that 'screen', which doesnt seem to work, unless of course the panner is still working on one screen, and not taking into account the virtual panner windows...
I've lost all sound output. Still works in xp. As root, reran alsaconf, alsamixer and alsactl store. No effect. Run xmms and all is normal except no sound; it plays the file, shows its title, the visual display is active as usual.Is there something I could have done that would mute all sound output?
View 3 Replies View RelatedI am planning to develop an application that will have a GUI. The first priority is stability and second is performance. Portability and eye candy is not important. To fit these primary requirements the app will be run under and optimized for Fluxbox WM.
What is the best GUI development kit such as Qt, GTK or FLTK that is best fit for such an app? I mean what is the most stable, reliable and fast GUI development library that works best with Fluxbox?
I use NetworkManager to handle my net connections and it's applet that allows me to control everything from the gui is called nm-applet. I was able to edit /etc/X11/xinit/xinitrc.fluxbox so that nm-applet starts when fluxbox does and away I go. From runlevel 3 that is.
On my laptop I like to boot into runlevel 4 for various reasons. When I start a fluxbox session from runlevel 4 this doesn't happen. What file do I have to edit to get this to start from runlevel 4?
I'm running Slackware 13.1 with fluxbox as my wm. I want to set up network-manager along with the pptp plugin. So far I've installed the NetworkManager and the network-manager-pptp plugin along with all the dependencies specified in the slackbuild packages which I downloaded from [URL]. I could use some help configuring the network-manager so that I can launch it as a regular user rather than as root and I want it to come up in the fluxbox toolbar if possible.
View 10 Replies View RelatedHey I just installed the wesnoth slackbuild. Then I tried to play it and it starts fine but when I click the buttons nothing happens.
So I tried exiting and used xwmconfig to switch to KDE from fluxbox. In KDE the buttons work.
ive used openbox for quite some time, but recently decided to make the switch to fluxbox. i have gotten everything up and running except for true transparency. i have seen screenshots in which this works, but i have not been able to duplicate the results.
in openbox, all i had to do was run cairo-compmgr at startup and my terminals were automatically transparent, and all the window effects i selected with cairo-compmgr were applied when i chose them. in fluxbox, i run cairo-compmgr, it starts up fine, and i know its running because i can use it's transparency settings to set whole windows to alpha (super + mouse scrolling), and the little "tab" buttons that fluxbox has have shadow effects drawn on them. the actual windows, however are not effected by cairo-compmgr running in the slightest. the windows themselves dont have shadows, and my terminals do not use transparency at all. even my xchat notifications have black boxes around them because not transparency is being used.
I like working with light text on black bg in Fluxbox however I need to use Kate editor which has bright white background and dark text. How can I change the background to black?(and the side panel of file list, too)? I presume I need to change the kde theme under Fluxbox. Does anyone know where the config file is and what to change in there if it's not obvious?
View 3 Replies View RelatedI often swapped window managers between fluxbox kde and gnome back when I ran ubuntu to suit my needs. When I installed slackware, I picked KDE because of the convenient app suite. I don't wish to uninstall kde but I'd like to be able to pick which environment I use when I swap to a GUI. Something like a flag, startx --fluxbox.
View 2 Replies View RelatedI have problem with my new distro and fluxbox. So I installed a slackware 13.37 with fluxbox, this is my first time with slack and fluxbox
I dont know how to install some netowrk manager and configure it in fluxbox I need wifi.
I've just install Slackware and Fluxbox windows manager. I suppose I have to configure some stuff, update my system, change theme etc etc. First of all I need to activate my wifi card because I can't have the laptop on my desk using ethernet all the time.
View 9 Replies View RelatedTrying to watch on-line videos in FluxBox - most will play some will not. I can't find any common thread re what does or doesn't play. Situation is the same no matter what browser I use (generally Swiftfox). If I switch to XFCE, there are no issues. Using standard install of 13.1 and have no other issues. Have no idea where to look or what to look for.
View 6 Replies View RelatedHere is what I have gotten my install down to with these packages:[url]
Just looking for suggestions on what packages I can still remove that are unnecessary for having firefox, fluxbox, pcmanfm, lxterminal, etc
And, I keep getting the error that the locale is not set, reverting to C? but I did set locale or thought I did, how to fix that?
I've just recently install slackware 13.1 on IBM R40e laptop but every time i try to start fluxbox with
startfluxbox it just comes up:
However xdm works.
The specs of the computer:
IBM R40e 2684 L9G
2.4GHz Intel celeron processor
128MB ram
ATI radeon 330M 16MB integrated
30GB hard drive
DVD rom drive
I'm not sure if it's of any use but here's my xorg.conf file:
Code:
I'm running the latest slackware64-current on my Dell laptop (Inspiron 1420). I rarely run it on battery power, so I don't know when this behavior started, but now it seems when I'm on battery power the hard drive likes to spin down and then spin up. This is not after 5 minutes or so of inactivity. This is 30 seconds of inactivity because I'm reading a web page or something. There is a noticable delay in the response of the system as a whole when the drive is having to spin back up. I'm also using xfce-4.6.2 with the xfce power manager. I've checked the settings, and I don't see anything about spinning down the hard drives. I've also looked through some ACPI rules, but I'm coming up empty.
View 3 Replies View RelatedMy linux laptop isn't able to detect the current battery state. I am using slackware64 13.37 xfce with a Toshiba L645 laptop.
This is what I came up with so far.
Code:
lsmod
Module Size Used by
snd_seq_dummy 1479 0
snd_seq_oss 30116 0
[Code].....
I use a program called conky that reports my cpu frequency and most of the time it's always at 0.93GHz instead of 2.53GHz. Sometimes it jumps to 1.20GHz and 2.53GHz but falls back down to 0.93GHz. Is this normal?
I noticed that there is a 1.0.1 version of xfce4-power-manager, so I tried it out last night. Note: It requires libxfce4ui >= 4.7. I compiled it using the same SlackBuild script as the one in Slackware 13.1. It compiled and installed just fine. However, when I logged out of XFCE and logged back in, I could only set a few options, and battery options were completely non-existant.
I double-checked, and my user account in in the power group. Has anyone else had a similar problem? In the meantime, I've downgraded back to the 0.8.5 version that Slackware ships with.
This is a new (Less than one month) old netbook that is just running Slackware 13.1 with KDE.Now, every 10 or so minutes I'm getting a "Battery disconnected/Not found" error and it's insisting I plug in.Now, the battery itself is fine since by ignoring these messages, I'm getting 5-6 hours battery life easily but none the less. It's a concern.It appears to be software related rather than a bad battery.Has anyone experienced this and/or know of a solution?
View 2 Replies View RelatedI am running Slackware64 -current. I just upgraded KDE to 4.6.0 from Alien Bob's ktown repo, and upon doing so my battery monitor no longer functions properly. More specifically, the icon will appear in the panel, but when I choose the option to show the charge/discharge state it does not show. The icon only ever shows that the battery is not plugged in to an external power source (showing a plug and a red x). It is important that I get the battery monitor functional once again as I am running my new Slackware64 -current install on a laptop and don't like to be left wondering when my laptop's battery will die and if I need to plug it in.
View 2 Replies View Relatedgetting back to our laptop, the stability window is ~3.2V. Meaning that when you operate the battery above this the electrolyte is oxidized on the positive electrode and reduced on the negative electrode. Remember that we only want to oxidize and reduce the active materials and don't want to do anything else. All these reactions other than the ones we want are called side reactions and these are really bad for the battery. The nominal voltage of a laptop battery is 3.7 V which means that something bad wants to happen as we use the battery.So long story short, stuff (e.g., passive layers and poor kinetics of reactions) happens and things are not as bad as they seem and you can increase the voltage up to 4.2V without bad things really happening. All chargers for Li-ion cells today cut the battery off when it reaches 4.2V. What you have to realize is that at 4.2V, these side reactions are present in finite amounts and start to chemically kill the battery, but its not that dramatic.
Operating to 4.1V makes things better and extends the life, 4.0 V is even better and so on. So why don't battery manufacturers cut the voltage off at, say, 4 V to get better battery life? Because every time you cut this voltage down you decrease the capacity of the battery and its run time. The 4.2V cutoff is a compromise between good run time and decent (read "not pathetic) life.On the other hand, if you charge the battery and then pull the plug (so to speak), the battery discharges some, the voltage drops, and these reactions become less of a problem and your battery life goes up. So the best things you can do is to charge the laptop (or cell phone, camera etc.) and once its charged, pull the plug. Your battery will thank you for it.As a matter of fact, if you own a Lenovo Thinkpad, you can actually change the state of charge to which you charge the battery using the Battery Maintenance utility. You can change this from charging to 100% state (where the voltage is 4.2V) to 90% so that your voltage is less. You lose some energy is doing that, but atleast you can change it to 100% when you need battery power and put it back down to 90% when you can plug in. I wish my Mac has the same feature.
I typically use the battery for a while (say 1/2 hour to 1 hour), then plug it in and wait to fully charge it, then I pull the plug and use it again for 1/2 hour to 1h and then I repeat this. Takes some getting used to and I forget to do this, but I try.
Just installed 9.10 followed by a 10.04 upgrade (wouldn't work as a 10.04 clean install). The install and upgrade all seemed to go well.
But now when booting I get a message saying "checking battery state" and then it boots no further. This is a laptop without a battery installed, running permanently from the mains through the charger.
How can I disable this check so that the laptop will still boot without a battery fitted?
I have included a "start" (slackware logo) button and an exit button. The problem is, neither of these buttons work. The start button should bring up the fluxbox menu but I have found to bring up this menu is by right clicking on the screen.the only way to logout and go back to the login screen seems to be via the fluxbox menu. Running "exit" from the command line only exits the terminal of course.
View 14 Replies View RelatedAny programs out there I can get to show this on my laptop please? I've searched this forum for "laptop" and "power", but threads are going on about increasing battery life and not actually showing how much battery is left on the machine.
View 14 Replies View RelatedI have a 3 year old laptop with the original battery and its drained pretty bad. The "Battery may be broken" popup was driving me insane and this is how you disable it, in case you are in the same situation as me. Open terminal
Code:
gconf-editor
Drill down to...
apps --> gnome-power-manager --> notify
uncheck the low_capacity checkbox. This should disable the popup for you if your battery has little life left in it. Now, if any knows how to disable the Avahi popup, let me know.
Is there any USB mouse battery indicators for Ubuntu that can tell me the battery level of my Logitech USB mouse? (something like a laptop battery one) I want to add it the panel.
View 6 Replies View RelatedI'm using Alarm-clock, not the alarm-clock-applet, and when i set Schedulle > AllWekdays an AllMonths the alarm gives me two pop-ups
View 1 Replies View Related