i wanaa to config tlenet server and did the steps to enable it
but when i try to connect to server this error show :
telnet : connect to address 10.0.0.100 : No route to host
telnet : Unable to connect to remote host : No route to host
[URL]
All I want is to be able to access files on one Ubuntu computer from another Ubuntu computer via a home wireless network. I have been at this for a week now. Scouring the web for answers and so far I have come up with this: Port 22 is open. I have both computers IP addr's via right clicking on the network icon-> Connection Information. ssh is installed and running. Both computers are listening on port22. But when I try Places->Connect to server, I get "no route to host". I'm not a networking guru and I'm at a complete loss on this.
View 9 Replies View RelatedI'm trying to ssh from my laptop to my desktop (both fedora 14) over a local network. I can ping my desktop and get responses, but if I ssh to it, I receive
ssh: connect to host 192.168.100.xxx port 22: No route to host
I can ssh from the desktop to itself.
I install and configure the vncserver following and reading 1000papers, but all of this present the same problem; when i try to connect to my vncserver,recive this mesage: unable connect to socket: No route to host (113) The OS version is Fedora Core 14 and tigervnc-server i try different solutions including:Allow TCP connection modifing files /etc/gdm/custom.conf and /usr/share/gdm/gdm.chemas Disable SELinux removing iptables Here follow the vncserver configuration:
[code].....
The ip address of the vncserver is correct because i can do ssh on it. Where or what can i do?
At nfs client end unable to mount nfs server.
mount: mount to NFS server '10.7.70.178' failed: System Error: No route to host.
I installed ntop on our server, after installing it, i ran ntop as a daemon. shortly after we lost the ability to ssh into the server.tried restarting ssh, but it didn't work, so had to restart the entire server.Where should we look to find why ssh suddenly stopped?
the error ssh gave when we try to connect was like: ssh: no route to host what log files should i look at and what should i look for to find the cause of the error?
I'm setting up apache on centOS 5.5 and administering it from another host on my LAN(this web server has no Xorg). I can ping from the config host to the web server but not the other way. My network is quite a way from being set up so i'm just configuring the web server at the moment, the simplest way i can. It's just trying to get two LAN hosts both with 192.168.1.0/24 I.Ps to talk to each other using a router to connect them.
Here are the outputs of ifconfig and netstat -rn for the web server, the config host and the router:
The ifconfig -a and netstat -rn of the config host are:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
[code]....
I cant send mail outs. I'm receiving
Quote:
When try send mails from pop3/imap or directly "root]#mail some@domain.com" but I CAN send mails to domains created in the server.
I stopped Iptables and still the error. The server is a common WHM/Cpanel installation with Centos 5.
Connection closed.
It has been years since I had to mess with sendmail (I prefer using postfix) - but I inherited a server that someone else configured. This machine is a webserver - but is running sendmail for the various webforms, etc. I want to configure sendmail on this machine to route ALL outgoing messages to the main email server. This means local users too. I have read through sendmail configurations for the past 3 hours, but it's mostly greek. Here is my current sendmail.mc file - could some kind soul tell me what I need to change (and WHERE)?
[code]...
My domain [URL]... has recently been moved to a new server. Since then, I have not been able to download email. Email sent to the domain can be seen in /var/spool/mail/akwebsoft, just as on the previous server. However when I go to download the email, I get the following error message (in part) in my fetchmail logfile:
[code]...
I am trying to access a DVD mounted on a machine running Fedora12 (192.168.0.105). I thought this should be possible with NFS, but the above error message is what I keep getting, no matter what I try.
Here is my mount command:
Code:
mount 192.168.0.105:/mnt/dvd -t nfs /tmp/scaleo
The Fedora 12 machine has the NFS server running, and the corresponding entry in /etc/exports is
Code:
/mnt/dvd *(ro)
I thought this might be a firewall problem, but it persists even if I turn firewalls off on both machines (client as well as server.) Also, doing
Code:
ssh 192.168.0.105
is OK, so what is wrong with the route?
I am trying to access a DVD mounted on a machine running Fedora12 (192.168.0.105). I thought this should be possible with NFS, but the above error message is what I keep getting, no matter what I try. Here is my mount command:
Code:
mount 192.168.0.105:/mnt/dvd -t nfs /tmp/scaleo
I now tried
Code:
mount 192.168.0.105:/mnt/dvd -t nfs4 /tmp/scaleo
and it seems the mount succeeded. So, instead of nfs, one must write nfs4?
I have 2 clients (one IP 200.x.y.52 and another 200.x.y.47) in ADSL conection and a same gateway (200.x.y.1).
When the server send an email, the error "No route to host" appear. I used TELNET 200.x.y.52 25 (110 soo) and the error occurr in both servers and both directions. The Firewall was disabled .
Ok so I just installed Ubuntu 10.10 Server Edition. On the very first boot, everything seems to run perfectly. I can SSH into it from any remote computer with no problems. However, the installation of certain things calls for a system reboot, which 2 days ago never would have been a problem. But now for some reason, the SSH server only wants to work on the very first boot of a clean install. After I reboot it, I get the ssh: connect to host 192.168.0.180 port 22: No route to host error. The absurd part is sshd is running! I've even tried restarting sshd, restarting the server, and using both 64 and 32 bit installs. The only way I can get anything to connect to it is by using ssh localhost. It won't even let me connect using the IP on the local machine!
View 1 Replies View Relatedusing redhat on server machine and open suse on client machine.i have installed nfs server and and it is running properly but when i want to mount shares from my client machine it gives the following.
error. "mount.nfs: mount to NFS server '10.3.31.146:/share' failed: System Error: No route to host" both systems ping each other and firewall is also disabled. another problem is when i remotely access from my server machine to client machine it gives the following error ssh:connect to host 10.3.31.147 port 22:connection refused what can be the problem?
So the problem is that phpMyAdmin does not want to connect to host name (at remote server) but connects to that same server fine if it's ip address is used. Command line "mysql -h hostname ..." works fine and connects to host name. Mysqladmin also works.
it's giving error:
*****
Error
MySQL said:
#2005 - Unknown MySQL server host 'host.name' (2)
******
I've disabled SElinux and temporarily disabled Iptables but no luck.
Somehow I feel MySQL is not doing DNS lookup when used by Apache/PHP. So it just understands ip addresses.
I found that on MySQL startup you can disable DNS lookup. [URL]
Not sure if it's disabled and how to enable it at startup. Could not find anything at "System" -> "Administration" -> "Services".
Here is similar case with no solution [URL]
Having trouble getting my Netgear WNA1000 working thru wireless router. Have tried lots of suggestions from other threads to no avail. Someone suggested that th routing table isn't set correctly, so have been trying to use the follwing to make the proper entry in the routing table: sudo route add -net 192.168.0.1 netmask 255.255.255.0 dev wlan0
Result: error message stating with:
"route: netmask does not match route address"
followed by "Usage" instructions which tell me to do what I just did. Any ideas on how I can populate my routing table with correct entry for my wireless card? Not to complicate matters, but I temporarily turned off encryption on my router to eliminate that as a possibility until I get connected. So maybe it'still trying to connect via encrypted mode - do I need to turn off encryption on my (client) end?
I've been for a while trying to configure my apache to host 5 domains as virtualhosts in the same IP address, but seems that neither one makes it through... it always takes first one, because it is the default:
NameVirtualHost *:80
<VirtualHost *:80>
ServerAdmin xxxxxxx@xxxx.net
[code]....
As you can see I tried the ServerName with the http://, in quotes, without it...
I use linux.
I have below error, no route to host.
Code:
Code:
Code:
Code:
Code:
Why can I not reach 192.168.1.1 ?
I have two machines: A.domain.com: (Old mail server): Red Hat 9 (Linux 2.4.20-30.9) B.domain.com: (New mail server): RHEL Client 5 (2.6.18-164.2.1.el5) (Both machines are in the same subnet and on the same switch). I wanted to test the new mail server by sending an E-mail message to it from the old one, but the maillog says
[code]...
I can ping from A.domain.com to B.domain.com and from B.domain.com to A.domain.com . I can traceroute -p 25 from A.domain.com to B.domain.com and from B.domain.com to A.domain.com. I can *telnet* on port 25 from B.domain.com to A.domain.com. BUT when I telnet on port 25 from A.domain.com to B.domain.com. I get "telnet: connect to address x.x.x.x: No route to host". The resolved IP x.x.x.x is correct by the way. So I see no reason why. it should fail to telnet on port 25 to A.domain.com.
HOW TO GET THE IP ADDRESS OF HOST IN LINUX WITH USING OF HOST AND NSLOOKUP COMMAND and after getting the ip address how to assign it in the variable
View 4 Replies View Relatedhost is windows 2003 server 64-bit
guest is ubuntu 9.04 server 64bit
Qemu : 0.11.1
Qemu manager: 7.0
from Qemu manager, if network card is using User Networking, it's a NAT and I can see that Guest Ubuntu has an ip address 10.0.2.15 and is able to access the internet. However, as Guest ubuntu is running server so I want to do use Tap networking and I assue with Tap, the Guest ubuntu will get an ip address which is in the same subnet as host machine by dhcp. so from Qemu Manager 7.0, I changed Network card to be:
NE2000PCI
Vlan Number =0
VLAN Type: Tap Networking
Mac address: tap0's mac address from host
TAP Network Adpator: Tap0
Note that tap0 was created by openvpn. and then fired Ubuntu guest, ifconfig shows no ip address on eth0 (which has the same mac address as Tap0) so the guest Ubuntu has no ip address and can't access public.
I am using fedora 14..i wanna create webservice in fedora 14...i am able to create sevice in server machine...but the client not able to get service from the server.it shows an error an i/o error has occured.no route to host.....we checked the ip address and port...i am able to ping the server...its connecting ...but it shows this error...?
View 1 Replies View RelatedI have 3 computers on a local home network. Computer 1 is not receiving incoming anything from other computers on the network, and I don't know why. The regular internet works fine.
Computer 1 can ping and ssh into either 2 or 3. 2 can ping and ssh into 3 and vice versa. But nothing can ping OR ssh into 1. Trying to do so says "no route to host".
All computers are running Ubuntu Karmic.
I have a server that I can ping, and I can connect remotely with ssh to it. But when I try to connect to apache (port 80) I get "no route to host". But I can connect to localhost It's not just my client system that is having this problem but also systems that are on the same subnet There is no firewall running on the server route on the server
[Code]...
We have a Red Hat Linux server that sends email out daily. It points to and Exchange server for smtp. It works fine, however, at least once a day, an email will fail and in the maillog I see "No route to host". After a few minutes, everything is working fine. The Linux server and Exchange are on the same VLAN and IP subnet.
View 2 Replies View RelatedI have two system, an Intel Core2 Duo system running the 32-bit version of Fedora 12, and a MacBook Pro running the 64-bit version of Fedora 12. I'm using the Gnome desktop on each system. I have enabled all the services I believe are necessary to support NFS including nfs, rpcbind, rpcgssd, rpcidmapd, and rpcsvcgssd on each system. I have added an entry to my /etc/exports file to export my home on each system, and if I type this command:
$ showmount -e localhost
I get a result like this:
Export list for localhost:
/home/tron 192.168.200.101,192.168.200.100
However when I issue this type of command:
$ showmount -e <remote host name>
I get this kind of result: rpc mount export: RPC: Unable to receive; errno = No route to host Research on the Internet indicates this is usually due to a firewall problem. However, I use the Firewall Configuration application to the disable the firewall on both systems, and I continue to get the same result. What is needed so I can get this two machines to display their exported file shares remotely? It turns out I did not disable the firewall when I thought I had. Now that I'm certain the firewall is disabled on both systems, I'm able to get the showmount command to succeed.
I setup my old laptop for my mom with F13 and have sshd running. My dad set up their DD-WRT router so that it's forwarding port 22 to the laptop's ip address. Yet, I get "No route to host" when I try and ssh in from my house. Is there anything that would be preventing F13 from accepting the SSH connection?
View 9 Replies View RelatedOpenSUSE version: 11.2 *and* 10.0 I am unable to send email. It appears I am being blocked by my ISP [URL]... A Wireshark trace shows ICMP type 3 Code 13 - "Administratively filtered". It's important to note that I don't know exactly when the problem started, because I seldom use my ISP email account, I use Yahoo web mail due to the "throwaway" nature if I get hit with spam. I only discovered the problem when testing the functionality of 11.2. I suspect the problem started several months ago: I restored openSUSE 10.0 and the problem exists there too. I wish I'd sent that last email via 10.0 before the upgrade.
The weird thing is that using Windows 2000 box I can get a successful connection using telnet (Telnet also fails on the openSUSE box.) It appears to me there is something in the Linux TCP stack that Teksavvy doesn't like. I am on dial up and I pointed this out to Teksavvy tech support, as I am probably the only person left on dialup and the reason no one else has reported the problem
I have 3 computers on a local home network. Computer 1 is not receiving incoming anything from other computers on the network, and I don't know why. The regular internet works fine. Computer 1 can ping and ssh into either 2 or 3. 2 can ping and ssh into 3 and vice versa. But nothing can ping OR ssh into 1. Trying to do so says "no route to host". All computers are running Ubuntu Karmic. I don't even know where to start figuring out what's causing this, but it's probably something simple. I'm using the IPs I found listed in my wireless router's web-based control panel.
View 9 Replies View Related