I'm somewhere between Novice and I have no idea what I'm doing with bash scripts. I'm writing a script to deploy images using partimage on my company's desktops, and while I have just about everything else figured out I have one issue left.Each of our 4 sites that will be using this disc will have a deployment server due to the fact that our sites have dedicated point to point links that our business traffic is conducted on. I need to be able to determine what site I'm at based onubnet and set a variable based on this determination. What I don't know is how to get the IP address in to an if statement, and properly determine subnet. For example:
192.168.1.0/16 - 192.168.7.0/16 need to use DEPLSERV01
192.168.8.0/16 - 192.168.16.0/16 use DEPLSERV02
192.168.17.0/16 - 192.168.24.0/16 use DEPLSERV03
I would like to know how do I print the line # in a script. My requirement is, I have a script which is about ~5000 lines long. If there are any errors happen I just exit. And I would like to add the line # of the script where the error happened.
Code: #!/bin/bash trap "echo 'you got me'" SIGINT SIGTERM # to trap ctrl+c echo "Press ctrl+c during 5 sec loop" for ((i=0;i<5;i++)); do
[Code]...
How come code behaves normally and stops when ctrl+c signal is caught and resumes, but after I use at least one timeout read in the code it looks like, if signal is caught again it doesn't pause the execution but skips the loop. If you remove -t (timeout) option from the read, both loops look the same!
Now in my bash script, I want to get the output /home/user instead of $HOME once read. So far, I have managed to get the $HOME variable but I can't get it to echo the variable. All I get is the output $HOME.
I have written quite a few separate bash & scripts and php scripts that up to now I have run from cron jobs. However I have to estimate how long each takes to run, before running the next and so it probably takes much longer than necessary to run them all. They have to run in order.
Now there are so many I am thinking it would be better to have a master bash script that would run one after the other, but I am not sure how to get the master script to wait before starting to run the next script. Is this possible and is there a command that will make the script wait between bash and php scripts , for them to finish, before running the next?
I think it would be better to count the len and remove 3 chars to right to get the extension, but it can be macintosh filenames with have 4 chars for extensions.
I need to rename the resulted searched files from a loopI have the following code:
find . -name DOC* | while read i do find $i -type f -name '*.txt' done
basically, I am searching for all txt files inside any folder starting with DOC name.this code is working fine with me.I need to rename those .txt files to .txtOLDOS: Ubuntu 10.4Bash shell
I am trying to write a bash script that sources another bash script. Essentially, I need a few lines to check to see if a certain variable is set. If not, I set it manually, and then source a scripts with that variable in the path. I wrote a test script to try it, but for some reason the last line does not work. Here is what I wrote:
#!/bin/sh source ~setupdir/setup.shrc #just a test, this line works echo ${#SETUP} # prints 0 if setup is not set, which it isn't if [ ${#SETUP} -eq 0 ] then SETUP="~setupdir" fi echo $SETUP # prints ~setupdir
I have a firewall between two different subnets. The reason for the second subnet within the internal network is because I have a mail server that I want to protect. However, we need to make sure that the mail server can communicate with the internal network as well.
Mail server is 192.168.100.100 Firewall is 192.168.100.1 and 10.110.101.5 (and its gateway is 10.110.101.1 to the router)
I go to another workstation and ping the mail server. I can't. It times out. I do the same from the mail server. It times out as well.
2 ethernet cardseth1 IP 192.168.1.254 Netmask 255.255.255.0 (fixed address) Internet eth0 IP 192.168.2.254 Netmask 255.255.255.0 (fixed address) LAN 01eth0:1 IP 172.16.1.254 Mask 255.255.255.0 (fixed address) LAN 02Lan 01 = Range (192.168.2.1 ~192.168.2.7) for 7 Stations fixed by mac addressLan 02 = Range (172.16.1.1 ~ 172.16.1.5) for 5 Stations fixed by mac address
I have a 2-floor house, with a single ethernet cable from the ground floor to the 1st. Downstair there is my ADSL modem, which is connected to the router upstair through this one cable. Now, I would like to have some more ethernet ports on the ground floor, but there's no room left to run another cable between the floors, so here's the big question: can I run both the modem-router connection and my regular LAN (which are on different subnets) through that one cable, with a switch at both ends?
To make it a little more clear, here is my present configuration
I have two subnets which I am interested in connecting.
Some basic network details:
Subnet A:
Subnet B:
I am trying to think of any further relevant details, but that seems to be it to me. If I forgot anything, please tell me.
Ok the question. WHAT do I type? (Explicitly!) And WHERE do I type it? In order to reach ubuntu-01.tec.lan, or ubuntu-02.tec.lan from perpetrator.tec.lan or rapine.tec.lan?
I'm interested in using actuall ROUTES. I can already achieve results similair to this with either a NAT firewall, or with VPN.. but that's not what I am interested in.
From what I have found out so far, I should need something like the following:
I have a network routing problem that I need to fix using a PC with ubuntu installed.
Here are the details of my problem: - I have two networks. - The first network is an ADSL router with subnet 192.168.1.x. I do not have access to the router nor change any of its configuration. - The second network has a subnet 172.26.x.x and connect via a wireless access point. Some of the devices connected to the network require to have static IPs. - I have a PC with ubuntu installed and two ethernet cards: one connected to the first network and the other connected to the access point. - I need to share the internet connection between the two networks using ubuntu. I already tried before on windows and the sharing worked when both networks were configured to use the same subnet. Once I changed the subnet of the second network, internet sharing stopped working.
Im having a issue with routing internet traffic from my router two different subnets (vlans).
Theres my setup:-
Server:
Both eth0,1 are running dhcp (two scoopes) that works fine!
The output of route -n is:
I have ip_forwarding on aswell, but i can ping the ip on the server running that dhcp scoope ie ping 192.168.4.1 works great but i just cant get the internet on the clients.
i have two subnets with different gateways.i am thinking of connecting them via a linux server which would enable them to communicate.but i dont know how to proceed for getting this done.how should the connection be made and what should be the configuration settings on the linux server.
I'm trying to build a linux(fedora 12) dhcpd server(and gateway), that have 3 network cards(eth0 have with public ip, eth1 192.168.2.1 class and eth3 with 192.168.3.1 class).
Because I have just a switch, I want to put both cables(from eth1, eth2) in the switch. Every client has 2 network card(eth0, eth1). My question is, is there any way to conf eth0 to take from server ip from 192.168.2.1 class, and eth1 from 192.168.3.1? The internet will work only on eth0.
I have some CISCO,Linux related problem with 2 Class C subnets:
192.168.64.0 -> PC5 192.168.65.0 -> PC6
Here's a picture of my situation: [URL]
HQ has to have 2 STATIC routes in order those 2 "PCs" mentioned above to have end to end connectivity with NETWORK A and NETWORK B. Now I try with
route0 -> network: 0.0.0.0, mask: 0.0.0.0, nexthop: Serial 0/0/0 route1 -> network: 0.0.0.0, mask: 0.0.0.0, nexthop: Serial 0/0/1
And it seems to work but I don't think it's proper! I feel it's kinda wrong ... but all my other attempts to set another couple of static routes ends in "Request timed out" and thus connection lost.
i'm in the process of learing C++. currently i'm creating shell scripts to get things done. i'm just curious how, as a programmer using C++ you would get a similar job done.as an example i have a script that takes the contents of files, pipes it to some sed and awk commands, which is piped to create a new file. that file is then imported into a mysql database.if you were going to do this in C++, would you call the sed/awk programs to modify the file, or can it be done within the program itself? i'm probably jumping the gun here because i've just started learing about pointers so this is above my ability
When trying to connect with SSH to address 192.168.1.100, I get a connection, when trying with address 192.168.2.200, SSH returns Network Error: Connection timed out.
Also receive no response when trying to ping 192.168.2.200 from a windows machine
If however Iadjust the wlan0 block in etc/network/interfaces to the following
I am able to connect to wlan0 in SSH to address 192.168.1.200, and I also receive requests when ping 192.168.1.200 from a windows machine. How can I use a different subnet for my wlan0 iface...
I have a Ubuntu server with multiple NICs and I'm just thinking about a potential scenario that might come up soon.
Imagine I have a network on floor 1 with an independent cable connection to my Ubuntu server -> switch -> assorted devices, on the subnet 192.168.0.x Now imagine friends upstairs have another independent network with cable -> router -> assorted devices, on subnet 192.168.1.x.
How can I set up my server to provide access for the 1.x subnet to the 0.x and vice versa. Ideally the devices all access internet from their appropriate subnet. I've read something about bridging, is this what I need?
I have one main subnet 192.168.50.0/24 with a defaultrouter 192.168.50.1 connected to the internet. I have an NFS server on that network. Everything is working as desired and machines are able to see each other and access the internet.
Now, I would like to add two more interfaces to the NFS server (running Slackware Linux), each on its own different subnet, say 192.168.51.0/24 and 192.168.52.0/24. The clients on those new subnets should also be able to access the internet (through the router 192.168.50.1). how to setup routing? Do I need any additional hardware router in between, or just a software configuration on the NFS server?
On a side note I have VLAN capable switches (couple of ProCurve 1800-24G) and would like to separate the three subnets using VLANs instead of using three separate switches.
I am trying to remember how to determine the number of subnets there are in a given subnet range. The example range is shown below:Quote:217.133.64.0-217.133.127.255nce I did the binary conversions of the two addresses shown, the address that I got when comparing the two was the following:Quote:217.133.192.0he number of subnets I got from his was 63.Correct me if I am wrong, but is the number of subnets the difference between the number, in this case, the third octet and 255? If there is another, or correct, way of determining the number subnets what would it entail?
I have a Ubuntu 10.10 box which i've developed an IPTables Firewall script and is forwarding my ports correctly. This service also runs Openswan VPN Server with 2 VPN's, which is also working well.
I have come across a small snag with excluding the multiple VPN subnets I have from the NAT on this box.
Which when added to IPTables does make the VPN come to life. But I can't seem to get it to add the second subnet. Unfortunately, I can't do a blanket exclusion such as 192.168.0.0/16 because the second VPN is on a Class B subnet address which I cannot change.
Connecting two networks with ipsec on this manual [URL] The two networks are connected, everything works, the question is as follows: For a gateway to multiple subnets, I have access to only one subnet is listed in / etc/sysconfig/network-scripts/ifcfg-ipsec0 DSTNET = 192.168.2.0/24. How do I get access to all the subnets?
I have a server hosting with in a DC and I have two subnet on 1 VLAN. how can I add all the IPs from these two subnet in one go? lets say for instructional purpose they are 192.168.0.0/24 and 192.168.1.0/24
We have a need to shape outgoing traffic EXCEPT to certain IP/subnets (sounds opposite to the title, but not really :P), using iptables if possible. We've had decent luck doing it with various things, but one of the big problems is the decrease in download speed (which DOES NOT need to be shaped at all) due to upload shaping. ie, we want the shaping not to apply to TCP/UDP overhead. Semi related but probably not important is the ability to shape virtualised systems as well (ie the guests), but as the guest traffic goes through the host any traffic shaping done on/to the host should affect the guests as well.
I have set up OpenVPN server using a bridged configuration. My networking "powers" aren't that advanced, so I did this by following the openvpn tutorial for bridged servers. I have tested this with several clients connecting to my server from different locations and it works very nicely (including broadcasts).
My server's LAN IP address is 192.168.2.4, and my LAN's mask is 24. Clients connecting to my server get assigned IP address that also fall within that subnet (i.e., the 192.168.2.x pool contains both physical machines in my home and "virtual" hosts). This is what the OpenVPN walkthrough specifies:
[Code]...
I was wondering if it would be possible for the VPN to fall within a different subnet (such as 10.0.1.x). I would also like to do that without adding another physical NIC to my server, or changing my physical IP address. I would imagine this is possible, since that's how hamachi does it.
