OpenSUSE Network :: Using 11.3 Gnome And Cannot Fix The Eth0 Connection
Apr 23, 2011
I'm using 11.3 gnome and cannot fix the eth0 connection. Tried to make it work with connection manager, ifup but both of them did'n make eth0 work. Here are some logs that you might wanna see:
lsmod:
Module Size Used by nls_utf8 1165 1 st - Pastebin.com
ifconfig:
eth0 Link encap:Ethernet HWaddr 1C:6F:65:47:03:16 UP BROADCAS - Pastebin.com
ifdown eth0:
[Code]....
I have TP-LINK router that sends wireless signal through the house which I'm using on my laptop's Ubuntu to connect on the internet, also I can connect with Ubuntu from laptop via the same cable that I'm trying to use on my desktop, so the router and cable are working. Also on my dekstop I've installed Windows 7 and can't connect from there either. The computer is new so i doubt that there is something wrong with its hardware. It all started when my connection disappeared. My ISP advised me to reset my router by plugging out the power cable and plugging it back in after 5min, and so I did. After that I could connect only from laptop. Tried to reinstall suse, to install ubuntu, but nothing worked. When I installed suse on my friend's computer, the only thing that I had to do is to open YaST and change the Network setup method from ifup to the NetworkManager, and also insert the MAC adress in the connection's properties. Tried that on my computer, but also didn't work.
View 2 Replies
ADVERTISEMENT
Oct 2, 2010
I recently setup a new SUSE box for the purposes of acting as an ftp/sftp server. It's currently setup to run ProFTPD 1.3.3.rc3 and mod_sftp/0.9.7. The server has two internal network interfaces eth0 and eth1. eth0 is purely for internal use to accept ftp and ssh. eth1 is outward facing and receives connections from the WAN via SFTP over port 22. The problem I am facing is that after half hour to an hour eth1 stops accepting connections whenever there is no SSH connection present on eth0. I can't figure out why this is happening.
ProFTPD is setup as follows: SocketBindTight directive is on, default server and port are commented out.
[code]...
When the external interface is unreachable the proftpd and proftpd-sftp logs show no record of any connection attempt. I have noticed however if I leave eth0 down eth1 stays contactable without problem. Can anyone give me some pointers on what I can check to find out why this may be happening.
View 2 Replies
View Related
Dec 13, 2010
When I log onto my Ubuntu 9.04 boot I am disconnected from the internet, on my windows 7 boot It works just fine, I have attempted disabling networking, power cycling the modem and router, and re-enabling networking, no dice though. hovering over the connection icon tells me that there is no network connection.
Opening the edit connections window tells me that there a wired connection called Auto eth0 that is set to never, and that is all that I can find. I hunted for other forums on this and found a few but none with a successful resolution.
View 1 Replies
View Related
Sep 25, 2010
I have recently upgraded the ubuntu desktop edition from 8.04 to 10.04. after upgrading i cannot show my eth0 nic interface in the System > Preferences > Network connections----- wired tab. and i also not getting network indication in the top of the panel beside the date time indication. but i can access network and using internet with that lan card. i cant understad my eth0 is connected or unpluged..
View 3 Replies
View Related
Aug 8, 2010
After rebooting, I found that the server couldn't see the network. The machine has dual gigabit ethernet (eth0 and eth1). eth0 is connected to the internet, but disappeared. ifconfig used to show eth0, eth1, and lo, but now only shows eth1 and lo. If I boot into rescue mode I can get internet and ifconfig returns eth0 and lo. Any ideas on how to fix this?
I apologize in advance if I ask any noob questions. I'm not a very experienced Linux user.
View 9 Replies
View Related
Dec 1, 2010
I've got access to my LAN and the Internet via my wired ethernet connection. I'd like to share that access with my iPod Touch (device shouldn't really matter) via an Ad-hoc wi-fi network.
This tutorial in the docs seems to describe the right setup but is very out of date (7.04). Instead I found this tutorial and followed it to create the Ad-hoc wireless network. I was able to connect my touch to the resulting ad-hoc network without a problem, but I didn't have LAN/Internet access.What's the next step to get the clients on the ad-hoc network out to the Internet?I found this page in the docs that says I'd need to install dnsmasq-base and uninstalling dnsmasq. I checked and dnsmasq-base is already installed but dnsmasq is not. I do have dnsmasq in /usr/sbin but the package description makes it sound like this should come with dnsmasq. Is the page out of date? Will uninstalling dnsmasq cause other problems?
View 9 Replies
View Related
Mar 3, 2010
I have my ubuntu box hard wired into my network. It all works fine, until I reboot my ubuntu box. After reboot, it can no longer see the network. I have it set up with a static ip. Not sure that I set it up completely correctly but it works fine...when working.. To fix the problem, I enter terminal: ifup eth0 That fixes all know problems until next reboot. What do I need to do so that it will remember settings and automatically be hooked into the network at power up?
View 3 Replies
View Related
Jun 7, 2010
I have a question regarding the configuration of Network Connection. My wired connection is fine right now and when I check the network connection applet, it display active information of eth0. However, when I click the Configure button, the Network Connection window appears but there's nothing in the Wired panel. Should there be a eth0 in that panel? I remember I had one before, but after I messed with some configuration of VPN, my network became unstable and I remove the Network Manager to try to solve the problem. Since then, there's nothing in my Network Connection window, though I can still connect to my router with eth0. Now even after I reinstalled the Network Manager, I still don't get anything.
View 7 Replies
View Related
Mar 8, 2010
If I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
View 9 Replies
View Related
Feb 14, 2010
Last night while setting up wired & wireless connection in openSuse 11.2 Gnome version via YAST's ifup, I got wireless but lost wired connection (interface eth0). Dmesg shows that eth0 became eth1. I cannot get eth0 back. Is there any way to remedy this situation, eg. get info from the Ubuntu partition in my triple-boot laptop, without having to re-install openSUSE?
View 3 Replies
View Related
Dec 24, 2010
I'm new to this forum site and I was wondering how can I bridge a network between the eth0 and wlan0 connections?my eth0 NIC is a RealTek RTL8111B 10/100/1000 Ethernet Card (OnBoard) and my wlan0 NIC is a RealTek RTL8187B 802.11b/g WiFi USB Adapter Card.Are there any utilities, such as bridge-utils that I can use, except for Firestarter since Firestarter states that the eth0 connection is not established, or do I right-click on the network icon and select Edit Connections and go to Auto eth0 and under the IPv4 Address setting and select Shared to other computers and run a live connection there?The main reason is that I need an Internet connection for my Xbox 360, which is connected to my Linksys WRT54G 802.11b/g Wireless Router, that has DD-WRT firmware installed and 4 WiFi hotspots for any wireless device, such as my PSP, DS, DS Lite, Wii, Laptop(s), my brother's PC (needs a WiFi card), and my dad's PC (needs either a WiFi card or an Internet connection from my brother's computer to my dad's PC)
Here are my Computer Specs:
ECS nForce6m-a Motherboard
2GB DDR-800 PC6400 Memory
[code]....
View 6 Replies
View Related
Apr 23, 2011
I own an ASUS N61JV-X2 notebook PC. It has an Atheros Communication, Inc. AR9285 Wireless Network Adapter. 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 0280: 168c:002b (rev 01) I cannot see any SSIDs including my home Verizon FiOS 802.11 G WPA2-AES-TKIP encrypted network. I went to Starbucks to try to connect to their free Wi-Fi and I could not make a connection. How do I solve this problem so that I can connect to a SSID of my choice and make a wireless connection while using GNOME 3?
View 2 Replies
View Related
Dec 1, 2009
I tried to update my fully-working 64-bit 11.1 system to 11.2. I used the network install and chose the Update option. It took a few hours so I didn't sit through the entire installation but when I returned the 11.2 login screen was displayed. Having logged in, however, I found that I couldn't access the network.The boot log showed that network had failed to start. "ifconfig" lists only the "lo" interface. "ifstatus eth0" returns "Interface eth0 is not available"
Network Settings in YaST lists 2 entries in the Overview tab. The first entry has Name:"NetXtreme BCM5755 Gigabit Ethernet PCI Express" and IP Address: "Not configured".The detail pane for this entry shows "NetXtreme BCM5755 Gigabit Ethernet PCI Express (Not connected) BusID:0000:3f00.0 Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details". The Edit and Delete buttons are both disabled for this entry.
The second entry has exactly the same name as the first with the IP Address listed as "DHCP4". I assume this was the entry that was carried over from the 11.1 system. The detail pane for this entry shows "NetXtreme BCM5755 Gigabit Ethernet PCI Express (No hwinfo) Device Name: eth0. Started automatically at boot. IP address assigned using DHCP4". The Edit and Delete buttons are both enabled for this entry.lspci reports "3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755 Gigabit Ethernet PCI Express (rev 02)"
lsmod lists only "edd", "loop", "sr_mod", "sg", "cdrom" and "dm_mod".
The files in /etc/sysconfig/network/ are "if-down.d/", "if-up.d/", "providers/", "scripts/", "config", "dhcp", "ifcfg-eth0", "ifcfg-lo", "ifcfg.template", "ifroute-lo",
[code]....
View 8 Replies
View Related
Jun 22, 2010
My eth0 is not up everytime at boot up. I will need to <service network restart> to get it up.
I have used yast's /etc/sysconfig editor to set /etc/sysconfig/network/config -> MANDATORY_DEVICES to eth0
And I have also added <alias eth0 e1000e> to /etc/modprobe.conf.local
And also set eth0 device to activate device at boot time using Network Card Setup.
But eth0 is still not starting up at boot time. What should I do to get it up at boot time?
I'm using openSUSE 10.3. And no, I'm am unable to move to 11.2
View 1 Replies
View Related
Jul 24, 2010
Last weekend I upgraded my Opensuse 11.1 machine (pretty clean) to 11.3. After the upgrade, the NVidia graphics no longer worked, but more importantly, eth0 was not bound to my Intel 82566DC gigabit ethernet controller. I fooled around in yast network devices long enough to know that everything there is configured correctly. The Yast message at the bottom of the Network Settings screen says:
"Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details."dmesg output shows nothing related to networking. The boot screen shows:
Setting up (localfs) network interfaces:
lo ...
Waiting for mandatory devices: eth0 __NCS__
29 28 27 ... 1 0 ... failed
eth0 no interface found ... failed
[code].....
Any ideas here? I've googled till my fingers were tired and all I've found are references from folks with real hardware issues. This machine worked fine for me under 11.1. Now I can't get 11.3 to bind the nic.
View 9 Replies
View Related
Apr 13, 2011
I want to set my desktop IP address to always be 192.168.1.2. The NetworkManager connects to the network automatically and the IP address is assigned randomly. I can set up another connection in NetworkManager and always change over. But is there any way to make the default eth0 interface to be permanently set to a certain address (using NetworkManager, not ifup)?
View 9 Replies
View Related
Jan 30, 2010
I tryed to setup a second IP address with yast on a openSUSE 11.2 on eth0 as eth0:2nd but with a different firewall zone. But SUSE firewall just see eth0.
I want to define with services are available on with IP address. Also with custom rules I can't specify a destination IP.
So now can I do this with yast? Or have I todo this manually without SUSE firewall?
View 2 Replies
View Related
Jun 1, 2011
I have been noticing a trend on boxes running 11.4 getting RX dropped packets where prior to 11.4 they did not get them. Basically every box running 11.4 now logs dropped RX packets. Have tried changing cables, and in one case replaced the NIC with a different brand (and driver) nic. Also played with receive buffers and yet the counters still increment. In addition to OpenSUSE, I run several operating systems to include Centos, Scientific Linux, Debian, OpenIndiana, HP-UX, VMS and so forth. So far this anomaly has only shown up on machines running OpenSUSE 11.4. Any one else noticing this on your OS 11.4 machines? If so, were you able to resolve?
[code]....
View 7 Replies
View Related
Jan 8, 2010
currently on an acer aspire 5532, and using mozilla and google chrome. webpages take about 10-12 seconds to load using the ethernet, wifi its about 2-3 seconds. using eth0 loading videos - broadcast yourself. in chrome, will sit at "resolving host" for about 10 seconds before bringing up the page. you would think eth0 is faster than wlan0, but for browsing the web its slower. i tested the speeds at speedtest.net - the global broadband speed test and both wlan0 and eth0 get the max speed my internet provides.i never downloaded drivers for the ethernet card or wifi, they worked so i didn't try to mess with them. but perhaps that is my problem?
code:
# lspci
00:00.0 host bridge: advanced micro devices [amd] rs780 host bridge
[code]....
View 6 Replies
View Related
Apr 22, 2010
I get connected to the internet via a router. The router dials to my provider and is connected to my computers via LAN and WLAN (mostly WLAN, see below). A few days ago I installed Suse11.2 to an old laptop (connected both ways: ethernet with wire and wireless ethernet).
The access to the online repositories worked only after I added the LAN-Adapter (Eth0) to the Demilitarised Zone of the firewall (I did also with the WLAN Adapter).
1. Is this normal?
2. Should I add the network devices now to an other zone?
I want to update my main laptop now from openSuse11.1 to 11.2 via new installation (from DVD) and make this installation right.
Or should I install only the data on the DVD and update after the installation via Yast?
(My main laptop has also an loose contact at the ethernet adapter.)
Greetings pistazienfresser
Now I am using (on my main laptop = Samsung X20) openSuse 11.1 and Gnome 2.24.1 (mostly, 1 account is using KDE) and Kernel Linux 2.6.27.45-01.1-pae. "/home" is on an separated partition (as part of an extended partition). I have also 2 NTFS partitions for Windows XP (System and Data), and a FAT, a root (/) and a swarp partition. My router is a AVM fritzbox 7270 (firewall should be included).
View 6 Replies
View Related
Jun 30, 2010
i'm using opensuse 11.3 and can't connect to the internet, my eth0 interface (which would be my modem i suppose) is found and when i "activate" it with ifup eth0, it gets stuck waiting for data (says so in ifstatus). If i try with knetworkmanager it is also stuck and doesn't connect to eth0. If i try to make it connect at boot, it doesn't work either.
I think the problem might be that in windows xp my modem has a "limited connection" but i can connect with my pppoe password anyway, but opensuse won't let me connect until it finds eth0 is working correctly which it never will because of how the internet company configures the modems i think. I don't know with which command i could "force" the pppoe connection even without a good connection to the modem, maybe that would work. But on the other hand, with other distros i can connect just fine so i don't know really.
View 1 Replies
View Related
Feb 27, 2011
I have installed Open SUSE in my DELL server which has 2 broadcom NIC cards, it showing both the NIC cards in Network configuration in YAST ,but it showing as not configured and not connected . Kernel device eth0,wlan0 are not present. In device manager also 2 Broadcom nic cards are detected.
View 4 Replies
View Related
Feb 28, 2011
The computer and system in question is the laptop from my description and openSUSE 11.3 with a different kernel from this repository :[URL]..free to move this thread if it should reside in the beta/prerelease forums section. The IMHO relevant information about my hardware and system is shown below.
The kernel I'm using :
Code:
grzes@opensuse:~> Linux opensuse.local 2.6.37.2-1-desktop #1 SMP PREEMPT 2011-02-25 19:59:41 +0100 i686 i686 i386 GNU/Linux
The hardware and drivers I'm using :
Code:
02:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
[Code]...
View 7 Replies
View Related
Dec 16, 2010
I have a laptop running OpenSuSE 11.2. I use the Yast menu to set up network settings via "traditional" ifconfig setup (not NetworkManager), because I found NM unusable in prior releases when doing network gymnastics such as router re-flashing, LAN reconfiguration, etc. where I needed control of the IP address, netmask, DHCP, tftp, etc. My laptop works fine with Yast "traditional" ifconfig configuration for eth0 connected to router to Internet. Works fine with Yast ifconfig configuration for USB WiFi as wlan1 to WiFi router to Internet. Also works fine for virtual machines on vmnets NAT-ed to the Internet. Works fine as long as there is only one network connection, that is.
Now, I have a second laptop. I want to network laptop #2 eth0 to laptop #1 eth0 for file transfer and/or Internet access WHILE laptop #1 is is linked to the Internet through wlan1. Unfortunately, I have not figured out how to get Yast/Network Configuration to do that. I have not been able to get Yast/Network Configuration to see both wlan1 and eth0 at the same time--when the Yast utility finishes, I do >ifconfig and >route, and I find that I have lost either eth0 or wlan1. Thus, when I do direct-connect file transfers, I loose the WiFi Internet connection on both machines.
I suspect that it might have something to do with Yast/Network Configuration utility not being able to handle two network interfaces on the host with different IP addresses. how to properly put an OpenSuSE machine on two networks simultaneously? And then how to turn on IP forwarding so that I can use laptop #1's WiFi as an Internet gateway for laptop #2?
View 1 Replies
View Related
Feb 21, 2011
im on node1 when i type the command ssh node2@ip the terminal hangs up a bit then an error message stating that connection timeout but here is a thing: i cant ping to node2
but i can terminate the ping manually using ctrl+c when i terminate the ping usual message appears stating 10 packets transmitted, 100% loss
ps: when i go to node3 and ssh to node2 it works fine and also i can ping from node3 to node2 very fine. and the firewalls are down at all nodes -all wired connection over a switch
View 6 Replies
View Related
Feb 2, 2010
I can make a connection to the vpn server, the connection starts, but nothing happens! My IP address remains the same as previous! There is nothing added to my Knetworkmanager, I'm a beginner I should use a pcf file for my vpn connection. I use it properly, I'm sure because the connection starts and an icon is added to my panel and remains until I disconnect.
I checked it via ifconfig -a, the last part (which is for vpn) is:
Code:
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:141.213.169.76 P-t-P:141.213.169.76 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1390 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
View 2 Replies
View Related
Jul 13, 2011
I've had 11.4/KDE working pretty well on dual boot Asus G73SW for a few weeks now. Only issues were the FN-* functions that control keyboard lights and whatnot but no biggie since the essential worked.The last couple of days the update notification was indicating 1,201 updates to be made. Yeah it seemed extreme but I googled around and checked the forums and there was nothing related. I figured I might be missing some packages since I installed from the live KDE CD (still 1202 updates!!!???). So I updated. Big mistake!!!!! Ever since NetworkManager cannot connect to the internet, be it wired or wireless.
Initially it could not even see my home network but it picked it up after I removed the plasmoid from the panel and reinstalled it. However it doesn't respond when I click the network icon and still no connection.I managed to get eth0 working with ifup but not wifi. The last part of network manager log file is quoted below. I can send the whole thing to whoever is interested. I can't make sense of it but maybe someone on the forums can.
Code:
Jul 13 11:09:08 linux-yy10 NetworkManager[1649]: <info> NetworkManager (version 0.8.9997) is starting...
[code]....
View 9 Replies
View Related
Jun 7, 2011
I've not found how to configure more than one ip address with network manager.Nor with kde nor with plasmoid network manager.I need several virtual ip addresses for eth0 when the "default" of eth0 is connected i.e. "Connected to Auto eth0" should initialize the virtual interfaces.I have not found no even how to configure the ip address.I think this will be used from ifup config in yast or not?There I have the virtual interfaces but they are not taken from network manager.And last but no least: Is it possible that when using network manager the eth0 is enabled even no user has logged in?
View 4 Replies
View Related
Nov 17, 2010
I deleted the firewall files "K09SuSEfirewall2_init", "K01SuSEfirewall2_setup", "S11SuSEfirewall2_setup" and "S01SuSEfirewall2_init" from "/etc/rc.d/rc5.d" in order to disable the firewall when rebooting.
As a consequence all network services are not working. I can't connect to any other machine nor to the internet.
I rebuilt the symbolic files based on the ones for runlevel 3, but still no network services are available.
Any suggestions how to make it work again? I'm using Suse 11.3.
View 9 Replies
View Related
Feb 1, 2010
Im new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.
I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).
I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.
View 1 Replies
View Related
