I'm running suse 11.1 which is configured as a router. Configured are two DSL connections with static IP's and one LAN connection (3 NIC's all together).
Problem: suse firewall will only port forward connections from one of the DSL connections and not the other.
Because I'm running two DSL connections is there something special I have to turn on/enable on the firewall?
As it stands I have a small home network operating behind my modem/router. Some of the ports on this are forwarded to my PS3 for gaming but I was looking at forward some for my file server.
At the moment I've forwarded port xxx22 to port 22 on my server for SSH for instance. ANd similarly 21 for FTP (although it doesnt seem to want to connect for any more than a few seconds using that). What I was thinking of doing was placing a small website for a handful of ppl to use on the server too and port forward again - xxx80 to 80. It works just fine but I'm a little concerned on the security front.
As I've moved the port to something different from the outside world I'm presuming I will have already cut the potential for malicious folks to wander in but is there anything else I should be doing? At the moment there's no firewall operating on the server, usually as its hidden behind the modem/router. But if I open this thign up more permanently what should I be doing? I've read a few articles on it but I'm always left with the overwhelming thought of "Thats if theres no firewall in my router" as they just seem to do the same.
I want to share my WiFi internet connection over LAN, so I'm trying to set up IP forwarding. An old tutorial tells me to go to Network Settings in YaST to do this, but that applet says that NetworkManager is now handling all of that stuff.How do I enable IP forwarding while NetworkManager handles my internet connections?
View 2 Replies View RelatedI used to have Opensuse 11.0 and Vuze 4.0.2 and both were working great. Recently I upgraded to OpenSuse 11.3 and installed Vuze 4.5.10. I did not change any configuration in the ADSL router but now I could not get the smiley icon to go green. I followed all the steps given here: A Quick Bittorrent Guide (with screenshots). It doesn't work. so I modified FW_ROUTE and FW_MASQUERADE to yes in /etc/sysconfig/SuSefirewall2. That also does not work. What did I miss here? My ADSL router is DSL-2640T.
View 3 Replies View RelatedI have the wake on lan option enabled on my debian computer. If i wake it by sending:
-mac adres
-internal ip in my home network
-subnetmask
-port 7
It all works fine, but when i try to do it from outside my network and change the ip address to the router adress it wont go on. I have also opened the port 7 in my router.
I have two SUSE(2.6) virtual machines running in the same subnet with two network cards each as shown below.
VM1------------------------------------------------------------------------------
appstage1:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:22:5A:24
inet addr:192.168.128.12 Bcast:192.168.128.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe22:5a24/64 Scope:Link
[Code]....
Ultimately my DB will run in VM2 and any DB requests coming in at 2055 of VM1 should be forwarded to port 2055 of VM2. Since I do not yet have a DB running I am trying to test with netcat.
I have logged into my router and set up port-forwarding on port 22. I can log into the machine fine from a machine on the local network using the machines internal IP but when I try to log on from a remote machine using my router's external IP or my DyDNS host-name I get a message saying "connection refused" or "connection timed out." I have configured port-forwarding on the router and the firewall rules says that port 22 is open but when I nmap my routers external ip it says that only port 23 and 80 are open. I am very new to linux and networking.
View 8 Replies View RelatedHow do you configure the firewall to allow external web access (it's a LAMP server) and internal access for samba shares ?
View 6 Replies View RelatedI'm trying to get my SSH server I set up on my home box working from behind a router. A 2wire 2700HG-B gateway, in fact. Now, I know my server is working fine, because I can get into it via loopback, anywhere inside the LAN from another machine, OR if I go into the router's config and enable DMZ for the machine. However, I don't like having DMZ on all the time because of the kludge-ness of it, and the security issue of the complete absence of a hardware firewall.If I try to port forward and access it from outside the LAN using the external IP (or my DynDNS, because it's dynamic), it just times out. I have a nonstandard port (45) for the listen port of the server, to keep away hack attempts if I were using the standard 22. I used this to see if the port was open, and it said it was. But, I tried the trick of telnetting the IP with that port, and it also timed out, instead of printing stuff about OpenSSH.
Attached is a screenie of my router's firewall page, so you all can look at it and see if I'm an idiot and doing it wrong. You might notice uTorrent there, it's because this machine is a dual-boot with 7, and the router doesn't differentiate the OS's. Also the SSH @ 46 port is for the Windows side, with freeSSHd. I changed the port on that one so the client I have can distinguish them, so it can run a reachability test.
Say I have Computer A behind a router with NAT. I'm unable to add any port forwarding rules to that router. Then I have Computer B with a public IP address that I want to forward X windows from. This computer is headless, but does have a video card so X windows can be used. Here are some of the things I'd perform to setup my scenario.
1. Computer B, I'd run xhost + public_ip of NAT router.
2. Make sure that computer B's sshd service has X11 forwarding enabled.
3. SSH from Computer A to Computer B with the X windows forward option.
4. Once in Computer B, set the DISPLAY env variable to the public_ip of NAT router.
5. On Computer B run xclock.
At this point I'd expect to see an instance of xclock originating from Computer B onto my desktop. However this obviously won't work. The problem is that when the request is made to Computer B to forward the instance of xclock to Computer A the forwarded instance of xclock will get stuck at the NAT router. Without a port forwarding rule the NAT router will not know which internal IP to route the instance of xclock.
Here's my question. Is there any way for Computer A to initiate a connection to Computer B and then forward the instance of xclock? That way if it uses that same connection the NAT router will know which internal IP to route it to because it would be an active connection in the router's routing table. Or is there an alternative? Of course I can vnc into another computer outside the NAT network and then forward an X window to it just fine. But in the spirit of expanding my knowledge on X windows I'd like to see what is possible.
1. Need to connect 2 CCTV DVRs and view from remote. 2. Can get a static IP address. But I dont know if this is a secure way since any once can view if the know the ip address. 3. Question is : is it possible to connect the DVR( s) to a linux server which will get user name and password before letting us view the DVR. Currently there is one set as follows: 1. From location X a device is connected to location Y using leased line and static IP (12 kms distance). In location Y a router is placed and port forwarding is configured. From Location Z using internet and remote desktop concept the device at location X is viewed and data captured. Is it possible to use a similar concept but with some sort of security authentication procedure in place.
View 1 Replies View Relatedwhat I have: Belkin G Wireless Router Model F5D7234-4. To attempt to get Subsonic working, I changed the port forwarding settings (Belkin calls it Virtual Servers) to forward port 4040 to my desktop computer. I then saved changes, and my wireless disconnected. I waited about 3 minutes, and nothing was happening, so I restarted my router. This left me in the position that I am in now. Even when the router and modem are fully booted, the router does not broadcast my SSID. In addition, a wired connection will not connect to the network through the router. This leaves me completely unable to use wireless, and unable to change any settings in the router.
View 3 Replies View RelatedI've managed to confirm that I can reach my home network via ssh from a remote location through my SMC Barricade when it is directly connected to the desktop machine but when the second router is put back into the chain ssh requests time out. The second router is a Linksys WRT 54GL running the Tomato firmware. The chain looks like this: ISP's router (bridged) --> Barricade -->WRT54GL-->desktop
The Barricade has port 22 forwarded to the Linksys' WAN address and it in turn forwards to the desktop address. It appears that it is a setting on the Linksys firmware that is preventing the remote connection. I've looked through the various settings many times but cannot see anything that would cause the problem.
I have just set up shorewall on my router running Arch Linux. The external network is on eth0 and the internal network on eth1.I have set it up for masquerading and that works fine and I can open ports to the firewall. But I'm having trouble with port forwarding to my internal machines.The problem I have is that when port 22350 is forwarded to 192.168.1.3 on my local network, checking the port with nmap from a remote computer gives me:
Code:
PORT STATE SERVICE
22350/tcp closed unknown
[code]....
I have a question about port forwarding. I have an internal Red Hat server and I would like to use it as a central connection point to some back end servers. This is not an internet router setup. I was thinking I could use iptables and do port forwarding similar to an internet router but internal to internal.
Basically I would like to take any connections to port 22 on server1 interface eth0 and forward them out of interface eth1 to server2 port 22.I am finding a lot of information on port forwarding, but it is all based on using an internet router that is passing through to an internal server. I need to know how to configure a basic linux setup with no existing iptables entries so that I can do this within an existing network.Also, if there is a better or easier approach I would appreciate any direction. I don't want to do this through an SSH tunnel.I know to start I need the following to enable forwarding in the kernel and a firewall PREROUTING rule.
I have an internal network behind a server <10.0.0.1> connected to the internet that NATs my ip <10.17.11.88> only. NAT is not allowed to any other ip addresses. When I use Transmission Bittorrent client to download torrents, The thing is that this 10.20.0.244 is not my machine and doesn't have access to the internet at all. What is happening here? Can anyone help me?
View 8 Replies View RelatedI am setting up Apache (Fedora 12) inside my home network. From inside my home network I access it without any problem. I need to set it up to access it from internet. I have the following questions. Here is temporary setup for testing purpose.
Internet-->ADSL modem (SEIMENS Speed Stream 4200)---> Apache (Fedora 12)
1. Do I have to do any kind of ports forwarding on ADSL modem. (There is no option to do port forwarding on Modem) May be I need different Model of Modem??
2. I tired to Ping my real IP for modem form another computer from internet. I am even unable to PING the ADSL 's real IP. Why it is that?
Is it fair to say that connLimit and hashlimit are very similiar on Linux i.e. while hashlimit caters to limits for groups of ports, they both set the connection rate limit per host? How in IPTables, do I configure a policy that limits connections on a port that encapsulates the total sum of all connections from all hosts? i.e. I do not want to allow more than 6000conn/minute for port range that is the sum of all connecting hosts?
View 3 Replies View RelatedI tried to make "ssh tunneling", but failed and got this message.
Quote:
Administrator@windstory-PC /
$ ssh -R 7869:localhost:7869 windowsstudy@192.168.0.4
windowsstudy@192.168.0.4's password:
Warning: remote port forwarding failed for listen port 7869 Last login: Wed Jul 21 01:56:04 2010 from 192.168.0.2 -bash-3.2$
1. system environment
192.168.0.2 - windows 7 + copssh
192.168.0.4 - centos 5.4 x86 + openssh
2. Guide for setting "ssh tunneling"
[URL]
3. Added this to sshd.conf
Quote:
AllowTcpForwarding yes
4. "netstat -na|grep 7869" at 192.168.0.4
Quote:
[root:maestro:~]# netstat -na|grep 7869
tcp 0 0 0.0.0.0:7869 0.0.0.0:* LISTEN
tcp 0 0 127.0.0.1:7869 127.0.0.1:53539 ESTABLISHED
[code]....
5. result of "ssh -vvv -R 7869:localhost:7869 windowsstudy@192.168.0.4"
Quote:
debug3: authmethod_lookup password
debug3: remaining preferred: ,password
debug3: authmethod_is_enabled password
[code]....
6. I added 7869 for telnet service as follow;
Quote:
mytelnet 7869/tcp # My Telnet server
sudo ssh -L 750:192.168.123.103:873 username@192.168.123.103It does exactly what it's supposed to do, but how do i edit / remove this rule?Is there some config file where i can alter the forwarding? How does it get stored?Im using Ubuntu 10.10Server Edition (allthough i recon it would be pretty much the same across all versions
View 5 Replies View RelatedI'm not that great with mailservers, and just been thrown a curveball with a MS Exchange environment for which there is apparently no solution... yeah, right. But is there a workaround?
The problem is that the site mail (SMTP) needs to be sent via port 26 instead of the commonly used 25. Port 25 is mapped to a mailfilter, which apparently causes havoc with some of the mail, and the techs that have been on site trying to coax the Exchange server to co-operate have said that the only way would be to get rid of the filter.
The problem is that there are number of apps that are unable to have the outgoing port changed and so keep sending mail out on port 25.
I look after the Unix/Linux side of things at work, and I was wondering if there was an easy way to set up a Ubuntu box to receive mail on port 25 and just forward it to the MS box on port 26? So, in other words (and I hope this makes sense): monitor port 25, and forward whatever comes in on port 25 to the server on port 26. Simple portforwarding, or is it? What steps do I need to take?
When I use the following command:
ssh user@ssh_server -L 5500:localhost:5500 -p 22
everything works fine. I can log in, and local port forwarding is done. Otherwise when I use the command:
ssh user@ssh_server -R 5500:localhost:5500 -p 22
I get an error "remote port forwarding failed for listen port 5500". However when I try remote port forwarding in WinXP by use of putty there is no problem...
I'll explain this in one sentence: Is it possible to program a port-binding shellcode in which people across the Internet can connect to, without being thwarted by the router blocking their data because the port its bound to doesn't allow port-forwarding
View 2 Replies View RelatedI want to set my ip as static and port forward it through a specific port can anyone help me with this im using ubuntu 10 with 64 bit OS
View 1 Replies View RelatedI have a mail server on which I would like to block port 25 on my eth0 for everyone except our external spam filter. the problem is that I want our users to be able to connect via port 10025 which is forwarded to port 25, which then is blocked...
View 2 Replies View RelatedI had to add them to my firewall script when I installed openvpn on my dd-wrt router:
iptables -I FORWARD -i br0 -o tun0 -j ACCEPT
iptables -I FORWARD -i tun0 -o br0 -j ACCEPT
iptables -I INPUT -i tun0 -j REJECT
iptables -t nat -A POSTROUTING -o tun0 -j MASQUERADE
what should I add/change to set up port forwarding of port 1000 to ip 192.168.1.200. also how to get the answer sent by 192.168.1.200 follow the same route used by the data received through port forwarding.
i want if a port (exp. 1001) have 20 connections that the next new connection forword to an other port (exp. 1002).
View 2 Replies View RelatedIn SuSE firewall0. I do have a openSuse 11.4 and multiple IP addresses on eth0 interface
I run (trying to/have to) multiple TOMCAT servers.
I am trying to have each tomcat instance listen to on separate IP address for example:
What i am trying to do is to redirect
a) tomcat 1 -
a) tomcat 2 -
And so on.
I know that it has to be possible.
I do have just eth0/
Is is it possible. Do I have to create "vittual interfaces"? eth0:1, .......... and do redirection ?
"Server" has got just single interface - just 1 ethernet calbe goes to that server. I am planning to have 10-15 tomcat's on that server (I have to unfortunatley) and each has to run on port 80
Is it possible to "grant" permissions to normal users to run app on port 80 - that would solve me lots of problems if impossible to redirect.
I tried to setcap 'cap_net_bind_service=+ep' /path/to/tomcat ...... but no luck
I have openSUSE 11.2 installed and i need to create a gateway server that allows virtual private network connections. I want to play with my friends some lan games, but we are in different networks, so i want to create this gateway server so we can connect with VPN clients to this server and play freely.
View 7 Replies View RelatedDoes anyone know how to permanently enable X connections from all machines on my local network. I keep having to enter 'xhost +' to allow X connections.
View 2 Replies View Related